Abstract: Asphalt surfaces are exposed to various weather
conditions and dynamic loading caused by passing trucks and
vehicles. In such situations, asphalt cement shows so different
rheological-mechanical behavior. If asphalt cement isn-t compatible
enough, asphalt layer will be damaged immediately and expensive
repairing procedures should be performed then. To overcome this
problem, researchers study on mechanical improved asphalt cement.
In this study, bentonite was used in order to modify bitumen
characteristics and the modified bitumen's characteristics were
investigated by asphalt cement tests. Then, the optimal bitumen
content in various compounds was determined and asphalt samples
with different contents of additives were prepared and tested. Results
show using this kind of additive not only has caused improvement in
bitumen mechanical properties, but also improvement in Marshall
Parameters was achieved.
Abstract: Utilization of waste material in asphalt pavement
would be beneficial in order to find an alternative solution to increase
service life of asphalt pavement and reduce environmental pollution
as well. One of these waste materials is Polyethylene Terephthalate
(PET) which is a type of polyester material and is produced in a large
extent. This research program is investigating the effects of adding
waste PET particles into the asphalt mixture with a maximum size of
2.36 mm. Different percentages of PET were added into the mixture
during dry process. Gap-graded mixture (SMA 14) and PG 80-100
asphalt binder have been used for this study. To evaluate PET
reinforced asphalt mixture different laboratory investigations have
been conducted on specimens. Marshall Stability test was carried
out. Besides, stiffness modulus test and indirect tensile fatigue test
were conducted on specimens at optimum asphalt content. It was
observed that in many cases PET reinforced SMA mixture had better
mechanical properties in comparison with control mixture.
Abstract: New advancement of technology and never satisfying demands of the civilization are putting huge pressure on the natural fuel resources and these resources are at a constant threat to its sustainability. To get the best out of the automobile, the optimum balance between performance and fuel economy is important. In the present state of art, either of the above two aspects are taken into mind while designing and development process which puts the other in the loss as increase in fuel economy leads to decrement in performance and vice-versa. In-depth observation of the vehicle dynamics apparently shows that large amount of energy is lost during braking and likewise large amount of fuel is consumed to reclaim the initial state, this leads to lower fuel efficiency to gain the same performance. Current use of Kinetic Energy Recovery System is only limited to sports vehicles only because of the higher cost of this system. They are also temporary in nature as power can be squeezed only during a small time duration and use of superior parts leads to high cost, which results on concentration on performance only and neglecting the fuel economy. In this paper Kinetic Energy Recovery System for storing the power and then using the same while accelerating has been discussed. The major storing element in this system is a Flat Spiral Spring that will store energy by compression and torsion.
The use of spring ensure the permanent storage of energy until used by the driver unlike present mechanical regeneration system in which the energy stored decreases with time and is eventually lost. A combination of internal gears and spur gears will be used in order to make the energy release uniform which will lead to safe usage. The system can be used to improve the fuel efficiency by assisting in overcoming the vehicle’s inertia after braking or to provide instant acceleration whenever required by the driver. The performance characteristics of the system including response time, mechanical efficiency and overall increase in efficiency are demonstrated. This technology makes the KERS (Kinetic Energy Recovery System) more flexible and economical allowing specific application while at the same time increasing the time frame and ease of usage.
Abstract: Curing of paints by exposure to UV radiations is
emerging as one of the best film forming technique as an alternative
to traditional solvent borne oxidative and thermal curing coatings.
The composition and chemistry of UV curable coatings and role of
multifunctional and monofunctional monomers, oligomers, and
photoinitiators have been discussed. The limitations imposed by
thermodynamic equilibrium and tendency for acrylic double bond
polymerizations during synthesis of multifunctional acrylates have
been presented. Aim of present investigation was thus to explore the
reaction variables associated with synthesis of multifunctional
acrylates. Zirconium oxychloride was evaluated as catalyst against
regular acid functional catalyst. The catalyzed synthesis of glyceryl
acrylate and neopentyl glycol acrylate was conducted by variation of
following reaction parameters: two different reactant molar ratios-
1:4 and 1:6; catalyst usage in % by moles on polyol- 2.5, 5.0 and 7.5
and two different reaction temperatures- 45 and 75 0C. The reaction
was monitored by determination of acid value and hydroxy value at
regular intervals, besides TLC, HPLC, and FTIR analysis of
intermediates and products. On the basis of determination of reaction
progress over 1-60 hrs, the esterification reaction was observed to
follow 2nd order kinetics with rate constant varying from 1*10-4 to
7*10-4. The thermal and catalytic components of second order rate
constant and energy of activation were also determined. Uses of
these kinetic and thermodynamic parameters in design of reactor for
manufacture of multifunctional acrylate ester have been presented.
The synthesized multifunctional acrylates were used to formulate and
apply UV curable clear coat followed by determination of curing
characteristics and mechanical properties of cured film. The overall
curing rates less than 05 min. were easily attained indicating
economical viability of radiation curable system due to faster
production schedules
Abstract: The current study has investigated the ageing
phenomena of silica optical fibres in relation to water activity which might be accelerated when exposed to a supplementary energy, such as microwaves. A controlled stress by winding fibres onto accurate
diameter mandrel was applied. Taking into account that normally a
decrease in fibre strength is induced in time by chemical action of water, the effects of cumulative reagents such as: water, applied stress and supplementary energy (microwave) in some cases acted in
the opposite manner. The microwave effect as a structural relaxation
catalyst appears unexpected, even if the overall gain in fibre strength is not high, but the stress corrosion factor revealed significant
increase in certain simulation conditions.
Abstract: Limited infrastructure development on peats and
organic soils is a serious geotechnical issues common to many
countries of the world especially Malaysia which distributed 1.5 mill
ha of those problematic soil. These soils have high water content and
organic content which exhibit different mechanical properties and
may also change chemically and biologically with time. Constructing
structures on peaty ground involves the risk of ground failure and
extreme settlement. Nowdays, much efforts need to be done in
making peatlands usable for construction due to increased landuse.
Deep mixing method employing cement as binders, is generally used
as measure again peaty/ organic ground failure problem. Where the
technique is widely adopted because it can improved ground
considerably in a short period of time. An understanding of
geotechnical properties as shear strength, stiffness and compressibility
behavior of these soils was requires before continues construction on
it. Therefore, 1- 1.5 meter peat soil sample from states of Johor and
an organic soil from Melaka, Malaysia were investigated. Cement
were added to the soil in the pre-mixing stage with water cement ratio
at range 3.5,7,14,140 for peats and 5,10,30 for organic soils,
essentially to modify the original soil textures and properties. The
mixtures which in slurry form will pour to polyvinyl chloride (pvc)
tube and cured at room temperature 250C for 7,14 and 28 days.
Laboratory experiments were conducted including unconfined
compressive strength and bender element , to monitor the improved
strength and stiffness of the 'stabilised mixed soils'. In between,
scanning electron miscroscopic (SEM) were observations to
investigate changes in microstructures of stabilised soils and to
evaluated hardening effect of a peat and organic soils stabilised
cement. This preliminary effort indicated that pre-mixing peat and
organic soils contributes in gaining soil strength while help the
engineers to establish a new method for those problematic ground
improvement in further practical and long term applications.
Abstract: Among all mechanical joining processes, welding has
been employed for its advantage in design flexibility, cost saving,
reduced overall weight and enhanced structural performance.
However, for structures made of relatively thin components, welding
can introduce significant buckling distortion which causes loss of
dimensional control, structural integrity and increased fabrication
costs. Different parameters can affect buckling behavior of welded
thin structures such as, heat input, welding sequence, dimension of
structure. In this work, a 3-D thermo elastic-viscoplastic finite
element analysis technique is applied to evaluate the effect of shell
dimensions on buckling behavior and entropy generation of welded
thin shells. Also, in the present work, the approximated longitudinal
transient stresses which produced in each time step, is applied to the
3D-eigenvalue analysis to ratify predicted buckling time and
corresponding eigenmode. Besides, the possibility of buckling
prediction by entropy generation at each time is investigated and it is
found that one can predict time of buckling with drawing entropy
generation versus out of plane deformation. The results of finite
element analysis show that the length, span and thickness of welded
thin shells affect the number of local buckling, mode shape of global
buckling and post-buckling behavior of welded thin shells.
Abstract: Nowadays, cardiac disease is one of the most common
cause of death. Each year almost one million of angioplasty interventions and stents implantations are made all over the world.
Unfortunately, in 20-30% of cases neointimal proliferations leads to
restenosis occurring within the following period of 3-6 months. Three major factors are believed to contribute mostly to the edge
restenosis: (a) mechanical damage of the artery-s wall caused by the
stent implantation, (b) interaction between the stent and the blood constituents and (c) endothelial growth stimulation by small (lower
that 1.5 Pa) and oscillating wall shear stress. Assuming that this last actor is particularly important, a numerical model of restenosis
basing on wall shear stress distribution in the stented artery was elaborated. A numerical simulations of the development of in-stent
restenosis have been performed and realistic geometric patterns of a
progressing lumen reduction have been obtained
Abstract: Virtual engineering technology has undergone rapid progress in recent years and is being adopted increasingly by manufacturing companies of many engineering disciplines. There is an increasing demand from industry for qualified virtual engineers. The qualified virtual engineers should have the ability of applying engineering principles and mechanical design methods within the commercial software package environment. It is a challenge to the engineering education in universities which traditionally tends to lack the integration of knowledge and skills required for solving real world problems. In this paper, a case study shows some recent development of a MSc Mechanical Engineering course at Department of Engineering and Technology in MMU, and in particular, two units Simulation of Mechanical Systems(SMS) and Computer Aided Fatigue Analysis(CAFA) that emphasize virtual engineering education and promote integration of knowledge acquisition, skill training and industrial application.
Abstract: In this paper, a new cooling system using a nacelle duct
is proposed for the mechanical room in the household refrigerator. The
conventional mechanical room consists of a condenser, a compressor
and an axial fan. The axial fan is mainly responsible for cooling the
condenser and the compressor. The new cooling system is developed
by replacing the axial fan with the nacelle duct including the small
centrifugal fan. The parametric study is carried out to find the optimum
designs of the nacelle duct in terms of performance and efficiency.
Through this study, it is revealed that the new system can reduce the
space, electrical power and noise compared with the conventional
system
Abstract: Micro electromechanical sensors (MEMS) play a vital
role along with global positioning devices in navigation of
autonomous vehicles .These sensors are low cost ,easily available but
depict colored noises and unpredictable discontinuities .Conventional
filters like Kalman filters and Sigma point filters are not able to cope
with nonwhite noises. This research has utilized H∞ filter in nonlinear
frame work both with Kalman filter and Unscented filter for
navigation and self alignment of an airborne vehicle. The system is
simulated for colored noises and discontinuities and results are
compared with not robust nonlinear filters. The results are found
40%-70% more robust against colored noises and discontinuities.
Abstract: In order to give high expertise the computer aided
design of mechanical systems involves specific activities focused on
processing two type of information: knowledge and data. Expert rule
based knowledge is generally processing qualitative information and
involves searching for proper solutions and their combination into
synthetic variant. Data processing is based on computational models
and it is supposed to be inter-related with reasoning in the knowledge
processing. In this paper an Intelligent Integrated System is proposed,
for the objective of choosing the adequate material. The software is
developed in Prolog – Flex software and takes into account various
constraints that appear in the accurate operation of gears.
Abstract: Hair is a non homogenous complex material which
can be associated with a polymer. It is made up 95% of Keratin.
Hair has a great social significance for human beings. In the High
Middle Ages, for example, long hairs have been reserved for kings
and nobles.
Most common interest in hair is focused on hair growth, hair types
and hair care, but hair is also an important biomaterial which can
vary depending on ethnic origin or on age, hair colour for example
can be a sign of ethnic ancestry or age (dark hair for Asiatic, blond
hair for Caucasian and white hair for old people in general).
In this context, different approaches have been conducted to
determine the differences in mechanical properties and characterize
the fracture topography at the surface of hair depending on its type
and its age.
A tensile testing machine was especially designed to achieve
tensile tests on hair. This device is composed of a microdisplacement
system and a force sensor whose peak load is limited to
3N. The curves and the values extracted from each experiment, allow
us to compare the evolution of the mechanical properties from one
hair to another.
Observations with a Scanning Electron Microscope (SEM) and
with an interferometer were made on different hairs. Thus, it is
possible to access the cuticle state and the fracture topography for
each category.
Abstract: The composite materials were prepared by sawdust, cassava starch and natural rubber latex (NR). The mixtures of 15%w/v gelatinized cassava starch and 15%w/v PVOH were used as the binder of these composite materials. The concentrated rubber latex was added to the mixtures. They were mixed rigorously to the treated sawdust in the ratio of 70:30 until achive uniform dispersion. The batters were subjected to the hot compression moulding at the temperature of 160°C and 3,000 psi pressure for 5 min. The experimental results showed that the mechanical properties of composite materials, which contained the gelatinized cassava starch and PVOH in the ratio of 2:1, 20% NR latex by weight of the dry starch and treated sawdust with 5%NaOH or 1% BPO, were the best. It contributed the maximal compression strength (341.10 + 26.11 N), puncture resistance (8.79 + 0.98 N/mm2) and flexural strength (3.99 + 0.72N/mm2). It is also found that the physicochemical and mechanical properties of composites strongly depends on the interface quality of sawdust, cassava starch and NR latex.
Abstract: Soft clays are defined as cohesive soil whose water
content is higher than its liquid limits. Thus, soil-cement mixing is
adopted to improve the ground conditions by enhancing the strength
and deformation characteristics of the soft clays. For the above
mentioned reasons, a series of laboratory tests were carried out to
study some fundamental mechanical properties of cement stabilized
soft clay. The test specimens were prepared by varying the portion of
ordinary Portland cement to the soft clay sample retrieved from the
test site of RECESS (Research Centre for Soft Soil). Comparisons
were made for both homogeneous and columnar system specimens
by relating the effects of cement stabilized clay of for 0, 5 and 10 %
cement and curing for 3, 28 and 56 days. The mechanical properties
examined included one-dimensional compressibility and undrained
shear strength. For the mechanical properties, both homogeneous and
columnar system specimens were prepared to examine the effect of
different cement contents and curing periods on the stabilized soil.
The one-dimensional compressibility test was conducted using an
oedometer, while a direct shear box was used for measuring the
undrained shear strength. The higher the value of cement content, the
greater is the enhancement of the yield stress and the decrease of
compression index. The value of cement content in a specimen is a
more active parameter than the curing period.
Abstract: Impact is one of very important subjects which always have been considered in mechanical science. Nature of impact is such that which makes its control a hard task. Therefore it is required to present the transfer of impact to other vulnerable part of a structure, when it is necessary, one of the best method of absorbing energy of impact, is by using Thin-walled tubes these tubes collapses under impact and with absorption of energy, it prevents the damage to other parts.Purpose of recent study is to survey the deformation and energy absorption of tubes with different type of cross section (rectangular or square) and with similar volumes, height, mean cross section thickness, and material under loading with different speeds. Lateral loading of tubes are quasi-static type and beside as numerical analysis, also experimental experiences has been performed to evaluate the accuracy of the results. Results from the surveys is indicates that in a same conditions which mentioned above, samples with square cross section ,absorb more energy compare to rectangular cross section, and also by increscent in speed of loading, energy absorption would be more.
Abstract: Abdominal aortic aneurysms rupture (AAAs) is one of the main causes of death in the world. This is a very complex phenomenon that usually occurs “without previous warning". Currently, criteria to assess the aneurysm rupture risk (peak diameter and growth rate) can not be considered as reliable indicators. In a first approach, the main geometric parameters of aneurysms have been linked into five biomechanical factors. These are combined to obtain a dimensionless rupture risk index, RI(t), which has been validated preliminarily with a clinical case and others from literature. This quantitative indicator is easy to understand, it allows estimating the aneurysms rupture risks and it is expected to be able to identify the one in aneurysm whose peak diameter is less than the threshold value. Based on initial results, a broader study has begun with twelve patients from the Clinic Hospital of Valladolid-Spain, which are submitted to periodic follow-up examinations.
Abstract: The procurement and cost management approach adopted for mechanical and electrical (M&E) services in Malaysian construction industry have been criticized for its inefficiency. The study examined early cost estimating practices adopted for mechanical and electrical services (M&E) in Malaysia so as to understand the level of compliance of the current techniques with best practices. The methodology adopted for the study is a review of bidding documents used on both completed and on – going building projects awarded between 2008 – 2010 under 9th Malaysian Plan. The analysis revealed that, M&E services cost cannot be reliably estimated at pre-contract stage; the bidding techniques adopted for M&E services failed to provide uniform basis for contractors to submit tender; detailed measurement of items were not made which could complicate post contract cost control and financial management. The paper concluded that, there is need to follow a structured approach in determining the pre-contract cost estimate for M&E services which will serve as a virile tool for post contract cost control.
Abstract: The objective from this paper is to design a solar
thermal engine for space vehicles orbital control and electricity
generation. A computational model is developed for the prediction of
the solar thermal engine performance for different design parameters and conditions in order to enhance the engine efficiency. The engine is divided into two main subsystems. First, the concentrator dish
which receives solar energy from the sun and reflects them to the
cavity receiver. The second one is the cavity receiver which receives
the heat flux reflected from the concentrator and transfers heat to the
fluid passing over. Other subsystems depend on the application required from the engine. For thrust application, a nozzle is
introduced to the system for the fluid to expand and produce thrust.
Hydrogen is preferred as a working fluid in the thruster application.
Results model developed is used to determine the thrust for a
concentrator dish 4 meters in diameter (provides 10 kW of energy),
focusing solar energy to a 10 cm aperture diameter cavity receiver.
The cavity receiver outer length is 50 cm and the internal cavity is 47
cm in length. The suggested design material of the internal cavity is
tungsten to withstand high temperature. The thermal model and
analysis shows that the hydrogen temperature at the plenum reaches
2000oK after about 250 seconds for hot start operation for a flow rate
of 0.1 g/sec.Using solar thermal engine as an electricity generation
device on earth is also discussed. In this case a compressor and
turbine are used to convert the heat gained by the working fluid (air)
into mechanical power. This mechanical power can be converted into
electrical power by using a generator.
Abstract: Cement, the most widely used construction material
is very brittle and characterized by low tensile strength and strain
capacity. Macro to nano fibers are added to cement to provide
tensile strength and ductility to it. Carbon Nanotube (CNT), one of
the nanofibers, has proven to be a promising reinforcing material in
the cement composites because of its outstanding mechanical
properties and its ability to close cracks at the nano level. The
experimental investigations for CNT reinforced cement is costly,
time consuming and involves huge number of trials. Mathematical
modeling of CNT reinforced cement can be done effectively and
efficiently to arrive at the mechanical properties and to reduce the
number of trials in the experiments. Hence, an attempt is made to
numerically study the effective mechanical properties of CNT
reinforced cement numerically using Representative Volume
Element (RVE) method. The enhancement in its mechanical
properties for different percentage of CNTs is studied in detail.