Abstract: Locating the critical slip surface with the minimum factor of safety for a rock slope is a difficult problem. In recent years, some modern global optimization methods have been developed with success in treating various types of problems, but very few of such methods have been applied to rock mechanical problems. In this paper, use of hybrid model based on artificial immune system and cellular learning automata is proposed. The results show that the algorithm is an effective and efficient optimization method with a high level of confidence rate.
Abstract: In order to answer the general question: “What does a simple agent with a limited life-time require for constructing a useful representation of the environment?" we propose a robot platform including the simplest probabilistic sensory and motor layers. Then we use the platform as a test-bed for evaluation of the navigational capabilities of the robot with different “brains". We claim that a protocognitive behavior is not a consequence of highly sophisticated sensory–motor organs but instead emerges through an increment of the internal complexity and reutilization of the minimal sensory information. We show that the most fundamental robot element, the short-time memory, is essential in obstacle avoidance. However, in the simplest conditions of no obstacles the straightforward memoryless robot is usually superior. We also demonstrate how a low level action planning, involving essentially nonlinear dynamics, provides a considerable gain to the robot performance dynamically changing the robot strategy. Still, however, for very short life time the brainless robot is superior. Accordingly we suggest that small organisms (or agents) with short life-time does not require complex brains and even can benefit from simple brain-like (reflex) structures. To some extend this may mean that controlling blocks of modern robots are too complicated comparative to their life-time and mechanical abilities.
Abstract: In the last decade, energy based control theory has undergone a significant breakthrough in dealing with underactated mechanical systems with two successful and similar tools, controlled Lagrangians and controlled Hamiltanians (IDA-PBC). However, because of the complexity of these tools, successful case studies are lacking, in particular, MIMO cases. The seminal theoretical paper of controlled Lagrangians proposed by Bloch and his colleagues presented a benchmark example–a 4 d.o.f underactuated pendulum on a cart but a detailed and completed design is neglected. To compensate this ignorance, the note revisit their design idea by addressing explicit control functions for a similar device motivated by a vector thrust body hovering in the air. To the best of our knowledge, this system is the first MIMO, underactuated example that is stabilized by using energy based tools at the courtesy of the original design idea. Some observations are given based on computer simulation.
Abstract: This paper presents a novel method for prediction of
the mechanical behavior of proximal femur using the general
framework of the quantitative computed tomography (QCT)-based
finite element Analysis (FEA). A systematic imaging and modeling
procedure was developed for reliable correspondence between the
QCT-based FEA and the in-vitro mechanical testing. A speciallydesigned
holding frame was used to define and maintain a unique
geometrical reference system during the analysis and testing. The
QCT images were directly converted into voxel-based 3D finite
element models for linear and nonlinear analyses. The equivalent
plastic strain and the strain energy density measures were used to
identify the critical elements and predict the failure patterns. The
samples were destructively tested using a specially-designed gripping
fixture (with five degrees of freedom) mounted within a universal
mechanical testing machine. Very good agreements were found
between the experimental and the predicted failure patterns and the
associated load levels.
Abstract: In order to study the influence of different methods of controlling weeds such as mechanical weeding and mechanical weeder efficiency analysis in mechanical cultivation conditions, in farming year of 2011 an experiment was done in a farm in coupling and development of technology center in Haraz,Iran. The treatments consisted of (I) control treatment: where no weeding was done, (II) use of mechanical weeding without engine and (III) power mechanical weeding. Results showed that experimental treatments had significantly different effects (p=0.05) on yield traits and number of filled grains per panicle, while treatments had the significant effects on grain weight and dry weight of weeds in the first, second and third weeding methods at 1% of confidence level. Treatment (II) had its most significant effect on number of filled grains per panicle and yield performance standpoint, which was 3705.97 kg ha-1 in its highest peak. Treatment (III) was ranked as second influential with 3559.8 kg ha-1. In addition, under (I) treatments, 2364.73 kg ha-1 of yield produced. The minimum dry weights of weeds in all weeding methods were related to the treatment (II), (III) and (I), respectively. The correlation coefficient analysis showed that total yield had a significant positive correlation with the panicle grain yield per plant (r= 0.55*) and the number of grains per panicle-1 (r= 0.57*) and the number of filled grains (r= 0.63*). Total rice yield also had negative correlation of r= -0. 64* with weed dry weight at second weed sampling time (17 DAT). The weed dry weight at third and fourth sampling times (24 and 40 DAT) had negative correlations of -0.65** and r=-0.61* with rice yield, respectively.
Abstract: During the last few years, several sheet hydroforming
processes have been introduced. Despite the advantages of these
methods, they have some limitations. Of the processes, the two main
ones are the standard hydroforming and hydromechanical deep
drawing. A new sheet hydroforming die set was proposed that has the
advantages of both processes and eliminates their limitations. In this
method, a polyurethane plate was used as a part of the die-set to
control the blank holder force. This paper outlines the Taguchi
optimization methodology, which is applied to optimize the effective
parameters in forming cylindrical cups by the new die set of sheet
hydroforming process. The process parameters evaluated in this
research are polyurethane hardness, polyurethane thickness, forming
pressure path and polyurethane hole diameter. The design of
experiments based upon L9 orthogonal arrays by Taguchi was used
and analysis of variance (ANOVA) was employed to analyze the
effect of these parameters on the forming pressure. The analysis of
the results showed that the optimal combination for low forming
pressure is harder polyurethane, bigger diameter of polyurethane hole
and thinner polyurethane. Finally, the confirmation test was derived
based on the optimal combination of parameters and it was shown
that the Taguchi method is suitable to examine the optimization
process.
Abstract: A Cable-Driven Locomotion Interface provides a low
inertia haptic interface and is used as a way of enabling the user
to walk and interact with virtual surfaces. These surfaces generate
Cartesian wrenches which must be optimized for each motorized
reel in order to reproduce a haptic sensation in both feet. However,
the use of wrench control requires a measure of the cable tensions
applied to the moving platform. The latter measure may be inaccurate
if it is based on sensors located near the reel. Moreover, friction
hysteresis from the reel moving parts needs to be compensated
for with an evaluation of low angular velocity of the motor shaft.
Also, the pose of the platform is not known precisely due to cable
sagging and mechanical deformation. This paper presents a non-ideal
motorized reel design with its corresponding control strategy that
aims at overcoming the aforementioned issues. A transfert function
of the reel based on frequency responses in function of cable tension
and cable length is presented with an optimal adaptative PIDF
controller. Finally, an hybrid position/tension control is discussed with
an analysis of the stability for achieving a complete functionnality of
the haptic platform.
Abstract: There are various solutions for improving existing overhead line systems with the general purpose of increasing their limited capacity. The capacity reserve of the existing overhead lines is an important problem that must be considered from different aspects. The paper contains a comparative analysis of the mechanical and thermal limitations of an existing overhead line based on certain calculation conditions characterizing the examined variants. The methodology of the proposed estimation of the permissible conductor temperature and maximum load current is described in detail. The transmission line model consists of specific information of an existing overhead line of the Latvian power network. The main purpose of the simulation tasks is to find an additional capacity reserve by using accurate mathematical models. The results of the obtained data are presented.
Abstract: Composite laminates are relatively weak in out of
plane loading, inter-laminar stress, stress concentration near the edge
and stress singularities. This paper develops a new analytical
formulation for laminated composite rotating disc fabricated from
symmetric sequential quasi isotropic layers to predict three
dimensional stress and deformation. This analysis is necessary to
evaluate mechanical integrity of fiber reinforced multi-layer
laminates used for high speed rotating applications such as high
speed impellers. Three dimensional governing equations are written
for rotating composite disc. Explicit solution is obtained with
"Frobenius" expansion series. Based on analytical results, there are
two separate zones of three dimensional stress fields in centre and
edge of rotating disc. For thin discs, out of plane deformations and
stresses are small in comparison with plane ones. For relatively thick
discs deformation and stress fields are three dimensional.
Abstract: Emphasis on the advancement of new materials and technology has been there for the past few decades. The global development towards using cheap and durable materials from renewable resources contributes to sustainable development. An experimental investigation of mechanical behaviour of sisal fibre-reinforced concrete is reported for making a suitable building material in terms of reinforcement. Fibre reinforced Composite is one such material, which has reformed the concept of high strength. Sisal fibres are abundantly available in the hot areas. Sisal fibre has emerged as a reinforcing material for concretes, used in civil structures. In this work, properties such as hardness and tensile strength of sisal fibre reinforced cement composites with 6, 12, 18 and 24% by weight of sisal fibres were assessed. Sisal fibre reinforced cement composite slabs with long sisal fibres were manufactured using a cast hand lay up technique. Mechanical response was measured under tension. The high energy absorption capacity of the developed composite system was reflected in high toughness values under tension respectively.
Abstract: Lightweight ceramic materials in the form of bricks
and blocks are widely used in modern construction. They may be
obtained by adding of rice husk, rye straw, etc, as porous forming
materials. Rice husk is a major by-product of the rice milling
industry. Its utilization as a valuable product has always been a
problem. Various technologies for utilization of rice husk through
biological and thermochemical conversion are being developed.
The purpose of this work is to develop lightweight ceramic
materials with clay matrix and filler of rice husk and examine their
main physicomechanical properties. The results obtained allow to
suppose that the materials synthesized on the basis of waste materials
can be used as lightweight materials for construction purpose.
Abstract: The intention of this lessons is to assess the probability
of optical coherence tomography (OCT) for biometric recognition.
The OCT is the foundation on an optical signal acquisition and
processing method and has the micrometer-resolution. In this study,
we used the porcine skin for verifying the abovementioned means. The
porcine tissue was sound acknowledged for structural and
immunohistochemical similarity with human skin, so it could be
suitable for pre-clinical trial as investigational specimen. For this
reason, it was tattooed by the tattoo machine with the tattoo-pigment.
We detected the pattern of the tattooed skin by the OCT according to
needle speed. The result was consistent with the histology images.
This result showed that the OCT was effective to examine the tattooed
skin section noninvasively. It might be available to identify
morphological changes inside the skin.
Abstract: Ti-6Al-4V alloy has demonstrated a high strength to
weight ratio as well as good properties at high temperature. The
successful application of the alloy in some important areas depends
on suitable joining techniques. Friction welding has many
advantageous features to be chosen for joining Titanium alloys. The
present work investigates the feasibility of producing similar metal
joints of this Titanium alloy by rotary friction welding method. The
joints are produced at three different speeds and the performances of
the welded joints are evaluated by conducting microstructure studies,
Vickers Hardness and tensile tests at the joints. It is found that the
weld joints produced are sound and the ductile fractures in the tensile
weld specimens occur at locations away from the welded joints. It is
also found that a rotational speed of 1500 RPM can produce a very
good weld, with other parameters kept constant.
Abstract: The wrinkling of a thin elastic bi-annular plate with piecewise-constant mechanical properties, subjected to radial stretching, is considered. The critical wrinkling stretching loading and the corresponding wrinkling patterns are extensively investigated, together with the roles played by both the geometrical and mechanical parameters.
Abstract: In the forming of ceramic materials the plasticity
concept is commonly used. This term is related to a particular
mechanical behavior when clay is mixed with water. A plastic
ceramic material shows a permanent strain without rupture
when a compressive load produces a shear stress that exceeds
the material-s yield strength. For a plastic ceramic body it
observes a measurable elastic behavior before the yield
strength and when the applied load is removed. In this work, a
mathematical model was developed from applied concepts of
the plasticity theory by using the stress/strain diagram under
compression.
Abstract: The fixed partial dentures are mainly used in the frontal
part of the dental arch because of their great esthetics. There are
several factors that are associated with the stress state created in
ceramic restorations, including: thickness of ceramic layers,
mechanical properties of the materials, elastic modulus of the
supporting substrate material, direction, magnitude and frequency of
applied load, size and location of occlusal contact areas, residual
stresses induced by processing or pores, restoration-cement
interfacial defects and environmental defects. The purpose of this
study is to evaluate the capability of Polarization Sensitive Optical
Coherence Tomography (PSOCT) in detection and analysis of
possible material defects in metal-ceramic and integral ceramic fixed
partial dentures. As a conclusion, it is important to have a non
invasive method to investigate fixed partial prostheses before their
insertion in the oral cavity in order to satisfy the high stress
requirements and the esthetic function.
Abstract: In the present study, the incorporation of graphene
into blends of acrylonitrile-butadiene-styrene terpolymer with
polypropylene (ABS/PP) was investigated focusing on the
improvement of their thermomechanical characteristics and the effect
on their rheological behavior. The blends were prepared by melt
mixing in a twin-screw extruder and were characterized by measuring
the MFI as well as by performing DSC, TGA and mechanical tests.
The addition of graphene to ABS/PP blends tends to increase their
melt viscosity, due to the confinement of polymer chains motion.
Also, graphene causes an increment of the crystallization temperature
(Tc), especially in blends with higher PP content, because of the
reduction of surface energy of PP nucleation, which is a consequence
of the attachment of PP chains to the surface of graphene through the
intermolecular CH-π interaction. Moreover, the above nanofiller
improves the thermal stability of PP and increases the residue of
thermal degradation at all the investigated compositions of blends,
due to the thermal isolation effect and the mass transport barrier
effect. Regarding the mechanical properties, the addition of graphene
improves the elastic modulus, because of its intrinsic mechanical
characteristics and its rigidity, and this effect is particularly strong in
the case of pure PP.
Abstract: This research aimed to modify pineapple leaf paper
(PALP) for using as wet media in the evaporation cooling system by
improving wet mechanical property (tensile strength) without
compromising water absorption property. Polyamideamineepichorohydrin
resin (PAE) and carboxymethylcellulose (CMC)
were used to strengthen the paper, and the PAE and CMC ratio of
80:20 showed the optimum wet and dry tensile index values, which
were higher than those of the commercial cooling pad (CCP).
Compared with CCP, PALP itself and all the PAE/CMC modified
PALP possessed better water absorption. The PAE/CMC modified
PALP had potential to become a new type of wet media.
Abstract: In the upstream we place a piece of ring and rotate
it with 83Hz, 166Hz, 333Hz,and 666H to find the effect of the
periodic distortion.In the experiment this type of the perturbation
will not allow since the mechanical failure of any parts of the
equipment in the upstream will destroy the blade system. This type of
study will be only possible by CFD. We use two pumps NS32
(ENSAM) and three blades pump (Tamagawa Univ). The benchmark
computations were performed without perturbation parts, and confirm
the computational results well agreement in head-flow rate. We
obtained the pressure fluctuation growth rate that is representing the
global instability of the turbo-system. The fluctuating torque
components were 0.01Nm(5000rpm), 0.1Nm(10000rmp),
0.04Nm(20000rmp), 0.15Nm( 40000rmp) respectively. Only for
10000rpm(166Hz) the output toque was random, and it implies that it
creates unsteady flow by separations on the blades, and will reduce the
pressure loss significantly
Abstract: This paper deals with the evaluation of flow properties
of polymeric matrix with natural animal fillers. Technical university
of Liberec cooperates on the long-term development of “green
materials“ that should replace conventionally used materials
(especially in automotive industry). Natural fibres (of animal and
plant origin) from all over the world are collected and adapted
(drying, cutting etc.) for extrusion processing. Inside the extruder
these natural additives are blended with polymeric (synthetic and
biodegradable - PLA) matrix and created compound is subsequently
cut for pellets in the wet way. These green materials with unique
recipes are then studied and their mechanical, physical and
processing properties are determined. The main goal of this research
is to develop new ecological materials very similar to unfilled
polymers. In this article the rheological behaviour of chosen natural
animal fibres is introduced considering their shape and surface that
were observed with use of SEM microscopy.