Abstract: Human heart valves diseased by congenital heart
defects, rheumatic fever, bacterial infection, cancer may cause stenosis
or insufficiency in the valves. Treatment may be with medication but
often involves valve repair or replacement (insertion of an artificial
heart valve). Bileaflet mechanical heart valves (BMHVs) are widely
implanted to replace the diseased heart valves, but still suffer from
complications such as hemolysis, platelet activation, tissue
overgrowth and device failure. These complications are closely related
to both flow characteristics through the valves and leaflet dynamics. In
this study, the physiological flow interacting with the moving leaflets
in a bileaflet mechanical heart valve (BMHV) is simulated with a
strongly coupled implicit fluid-structure interaction (FSI) method
which is newly organized based on the Arbitrary-Lagrangian-Eulerian
(ALE) approach and the dynamic mesh method (remeshing) of
FLUENT. The simulated results are in good agreement with previous
experimental studies. This study shows the applicability of the present
FSI model to the complicated physics interacting between fluid flow
and moving boundary.
Abstract: This paper presents PSS (Power system stabilizer) design based on optimal fuzzy PID (OFPID). OFPID based PSS design is considered for single-machine power systems. The main motivation for this design is to stabilize or to control low-frequency oscillation on power systems. Firstly, describing the linear PID control then to combine this PID control with fuzzy logic control mechanism. Finally, Fuzzy PID parameters (Kp. Kd, KI, Kupd, Kui) are tuned by Genetic Algorthm (GA) to reach optimal global stability. The effectiveness of the proposed PSS in increasing the damping of system electromechanical oscillation is demonstrated in a one-machine-infinite-bus system
Abstract: The motion planning technique described in this paper has been developed to eliminate or reduce the residual vibrations of belt-driven rotary platforms, while maintaining unchanged the motion time and the total angular displacement of the platform. The proposed approach is based on a suitable choice of the motion command given to the servomotor that drives the mechanical device; this command is defined by some numerical coefficients which determine the shape of the displacement, velocity and acceleration profiles. Using a numerical optimization technique, these coefficients can be changed without altering the continuity conditions imposed on the displacement and its time derivatives at the initial and final time instants. The proposed technique can be easily and quickly implemented on an actual device, since it requires only a simple modification of the motion command profile mapped in the memory of the electronic motion controller.
Abstract: The tensile properties of Mg-3%Al nanocrystalline
alloys were investigated at different test environment. Bulk
nanocrystalline samples of these alloy was successfully prepared by
mechanical alloying (MA) followed by cold compaction, sintering,
and hot extrusion process. The crystal size of the consolidated milled
sample was calculated by X-Ray line profile analysis. The
deformation mechanism and microstructural characteristic at
different test condition was discussed extensively. At room
temperature, relatively lower value of activation volume (AV) and
higher value of strain rate sensitivity (SRS) suggests that new rate
controlling mechanism accommodating plastic flow in the present
nanocrystalline sample. The deformation behavior and the
microstructural character of the present samples were discussed in
details.
Abstract: Depressurization and pressurization streams in
industrial systems constitute a work exchange network (WEN). In this
paper, a novel graphical approach for targeting energy conservation
potential of a WEN is proposed. Through constructing the composite
work curves in the pressure-work diagram and assuming all of the
mechanical energy of the depressurization streams is recovered by
expanders, the maximum work target of a WEN can be determined via
the proposed targeting steps. A WEN in an ammonia production
process is used as a case study to illustrate the applicability of the
proposed graphical approach.
Abstract: The aim of this study was to analyse the most
important parameters determining the quality of the motion structure
of the basic classical dance jump – grand jeté.Research sample
consisted of 8 students of the Dance Conservatory in Brno. Using the
system Simi motion we performed a 3D kinematic analysis of the
jump. On the basis of the comparison of structure quality and
measured data of the grand jeté, we defined the optimal values of the
relevant parameters determining the quality of the performance. The
take-off speed should achieve about 2.4 m·s-1, the optimum take-off
angle is 28 - 30º. The take-off leg should swing backward at the
beginning of the flight phase with the minimum speed of 3.3 m·s-1.If
motor abilities of dancers achieve the level necessary for optimal
performance of a classical dance jump, there is room for certain
variability of the structure of the dance jump.
Abstract: the effects of refining and alkaline chemicals on potential of recycling bleached chemical pulp of bagasse were investigated in this study. Recycling was done until three times. Handsheet properties such as, apparent density, light scattering coefficient, tear index, burst index, breaking length, and fold number according to TAPPI standard were measured. Water retention value also was used to considering the treatments during recycling. Refining enhanced the strength of recycled pulp by increasing fiber flexibility and swelling ability, whereas by applying chemical treatment didn't observe any improvement. The morphology of recycled fiber was considered with scanning electron microscopy (SEM).
Abstract: Today automobile and aerospace industries realise Laser Beam Welding for a clean and non contact source of heating and fusion for joining of sheets. The welding performance is mainly based on by the laser welding parameters. Some concepts related to Artificial Neural Networks and how can be applied to model weld bead geometry and mechanical properties in terms of equipment parameters are reported in order to evaluate the accuracy and compare it with traditional modeling schemes. This review reveals the output features of Titanium and Aluminium weld bead geometry and mechanical properties such as ultimate tensile strength, yield strength, elongation and reduction of the area of the weld using Artificial Neural Network.
Abstract: In this paper as showed a non-invasive 3D eye tracker
for optometry clinical applications. Measurements of biomechanical
variables in clinical practice have many font of errors associated with
traditional procedments such cover test (CT), near point of
accommodation (NPC), eye ductions (ED), eye vergences (EG) and,
eye versions (ES). Ocular motility should always be tested but all
evaluations have a subjective interpretations by practitioners, the
results is based in clinical experiences, repeatability and accuracy
don-t exist. Optometric-lab is a tool with 3 (tree) analogical video
cameras triggered and synchronized in one acquisition board AD.
The variables globe rotation angle and velocity can be quantified.
Data record frequency was performed with 27Hz, camera calibration
was performed in a know volume and image radial distortion
adjustments.
Abstract: Internal combustion engines rejects 30-40% of the
energy supplied by fuel to the environment through exhaust gas. thus, there is a possibility for further significant improvement of efficiency with the utilization of exhaust gas energy and its conversion to mechanical energy or electrical energy. The Thermo-Electric
Generator (TEG) will be located in the exhaust system and will make use of an energy flow between the warmer exhaust gas and the external environment. Predict to th optimum position of temperature
distribution and the performance of TEG through numerical analysis.
The experimental results obtained show that the power output significantly increases with the temperature difference between cold
and hot sides of a thermoelectric generator.
Abstract: Acoustic function plays an important role in
aerodynamic mechanical engineering. It can classify the kind of
air-vehicle such as subsonic or supersonic. Acoustic velocity
relates with velocity and Mach number. Mach number relates
again acoustic stability or instability condition. Mach number
plays an important role in growth or decay in energy system.
Acoustic is a function of temperature and temperature is directly
proportional to pressure. If we control the pressure, we can control
acoustic function. To get pressure stability condition, we apply
Navier-Stokes equations.
Abstract: When a high DC voltage is applied to a capacitor with
strongly asymmetrical electrodes, it generates a mechanical force that
affects the whole capacitor. This phenomenon is most likely to be
caused by the motion of ions generated around the smaller of the two
electrodes and their subsequent interaction with the surrounding
medium. A method to measure this force has been devised and used.
A formula describing the force has also been derived. After
comparing the data gained through experiments with those acquired
using the theoretical formula, a difference was found above a certain
value of current. This paper also gives reasons for this difference.
Abstract: Aluminum/Copper clad sheet has been fabricated using
asymmetric extrusion method, which caused severe shear deformation
between Al and Cu plate to easily bond to each other. Interfacial
microstructure and mechanical properties of Al/Cu clad were studied
by scanning electron microscope equipped with energy dispersive
X-ray detector, micro-hardness, and tension tests. The asymmetric
extrusion bonding was very effective to provide a good interface for
atoms diffusion during subsequent annealing. The strength of bonding
was higher with the increasing extrusion ratio.
Abstract: Carbon steel is used in boilers, pressure vessels, heat
exchangers, piping, structural elements and other moderatetemperature
service systems in which good strength and ductility are
desired. ASME Boiler and Pressure Vessel Code, Section II Part A
(2004) provides specifications of ferrous materials for construction of
pressure equipment, covering wide range of mechanical properties
including high strength materials for power plants application.
However, increased level of springback is one of the major problems
in fabricating components of high strength steel using bending.
Presented work discuss the springback simulations for five different
steels (i.e. SA-36, SA-299, SA-515 grade 70, SA-612 and SA-724
grade B) using finite element analysis of air V-bending. Analytical
springback simulations of hypothetical layered materials are
presented. Result shows that; (i) combination of the material property
parameters controls the springback, (ii) layer of the high ductility
steel on the high strength steel greatly suppresses the springback.
Abstract: In this paper static and dynamic response of a
varactor of a micro-phase shifter to DC, step DC and AC
voltages have been studied. By presenting a mathematical
modeling Galerkin-based step by step linearization method
(SSLM) and Galerkin-based reduced order model have been
used to solve the governing static and dynamic equations,
respectively. The calculated static and dynamic pull-in
voltages have been validated by previous experimental and
theoretical results and a good agreement has been achieved.
Then the frequency response and phase diagram of the system
has been studied. It has been shown that applying the DC
voltage shifts down the phase diagram and frequency
response. Also increasing the damping ratio shifts up the
phase diagram.
Abstract: The carbon based coils with the nanometer scale have
the 3 dimension helix geometry. We synthesized the carbon nano-coils
by the use of chemical vapor deposition technique with iron and tin as
the catalysts. The fabricated coils have the external diameter of
ranging few hundred nm to few thousand nm. The Scanning
Electro-Microscope (SEM) and Tunneling Electro-Microscope has
shown detail images of the coil-s structure. The fabrication of the
carbon nano-coils can be grown on the metal and non-metal substrates,
such as the stainless steel and silicon substrates. Besides growth on the
flat substrate; they also can be grown on the stainless steel wires. After
the synthesis of the coils, the mechanical and electro-mechanical
property is measured. The experimental results were reported.
Abstract: In industry, on of the most important subjects is die
and it's characteristics in which for cutting and forming different
mechanical pieces, various punch and matrix metal die are used.
whereas the common parts which form the main frame die are not
often proportion with pieces and dies therefore using a part as socalled
common part for frames in specified dimension ranges can
decrease the time of designing, occupied space of warehouse and
manufacturing costs. Parts in dies with getting uniform in their shape
and dimension make common parts of dies. Common parts of punch
and matrix metal die are as bolster, guide bush, guide pillar and
shank. In this paper the common parts and effective parameters in
selecting each of them as the primary information are studied,
afterward for selection and design of mechanical parts an
introduction and investigation based on the Mech. Desk. software is
done hence with developing this software can standardize the metal
common parts of punch and matrix. These studies will be so useful
for designer in their designing and also using it has with very much
advantage for manufactures of products in decreasing occupied
spaces by dies.
Abstract: Minimum Quantity Lubrication (MQL) technique
obtained a significant attention in machining processes to reduce
environmental loads caused by usage of conventional cutting fluids.
Recently nanofluids are finding an extensive application in the field
of mechanical engineering because of their superior lubrication and
heat dissipation characteristics. This paper investigates the use of a
nanofluid under MQL mode to improve grinding characteristics of
Ti-6Al-4V alloy. Taguchi-s experimental design technique has been
used in the present investigation and a second order model has been
established to predict grinding forces and surface roughness.
Different concentrations of water based Al2O3 nanofluids were
applied in the grinding operation through MQL setup developed in
house and the results have been compared with those of conventional
coolant and pure water. Experimental results showed that grinding
forces reduced significantly when nano cutting fluid was used even at
low concentration of the nano particles and surface finish has been
found to improve with higher concentration of the nano particles.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: Mechanical and water transport properties of high
performance concrete (HPC) containing natural zeolite as partial
replacement of Portland cement are studied. Experimental results
show that in the investigated mixes the use of natural zeolite leads to
an increase of porosity, decrease of compressive strength and
increase of moisture diffusivity and water vapor diffusion coefficient,
as compared with the reference HPC. However, for the replacement
level up to 20% of the mass of Portland cement the concretes still
maintain their high performance character and exhibit acceptable
water transport properties. Therefore, natural zeolite can be
considered an environmental friendly binder with a potential to
replace a part of Portland cement in concrete in building industry.