Abstract: This study uses GIS (Geographic Information
Systems) to conduct an evaluation of the degree of the sufficiency of
public green spaces such as parks and urban green areas as an
indicator of the density of metropolitan areas, in particular the Chubu
metropolitan area, in Japan. To that end, it first grasps the distribution
situation of green spaces in the three metropolitan areas in Japan,
especially in the Chubu metropolitan area, using GIS digital maps.
And based on this result, it conducts a GIS evaluation of the degree of
sufficiency of public green spaces and arranges the result for every
distance belt from the central part to compare and exam for every
distance belt away from the center in the Chubu metropolitan area.
Furthermore, after pointing out the insufficient areas of public green
spaces based on the result, it also proposes the improvement policy
which can be introduced in the Chubu metropolitan area.
Abstract: This paper presents the results of a comprehensive
investigation of five blackouts that occurred on 28 August to 8
September 2011 due to bushing failures of the 132/33 kV, 125 MVA
transformers at JBB Ali Grid station. The investigation aims to
explore the root causes of the bushing failures and come up with
recommendations that help in rectifying the problem and avoiding the
reoccurrence of similar type of incidents. The incident reports about
the failed bushings and the SCADA reports at this grid station were
examined and analyzed. Moreover, comprehensive power quality
field measurements at ten 33/11 kV substations (S/Ss) in JBB Ali
area were conducted, and frequency scans were performed to verify
any harmonic resonance frequencies due to power factor correction
capacitors. Furthermore, the daily operations of the on-load tap
changers (OLTCs) of both the 125 MVA and 20 MVA transformers
at JBB Ali Grid station have been analyzed. The investigation
showed that the five bushing failures were due to a local problem, i.e.
internal degradation of the bushing insulation. This has been
confirmed by analyzing the time interval between successive OLTC
operations of the faulty grid transformers. It was also found that
monitoring the number of OLTC operations can help in predicting
bushing failure.
Abstract: The present work is concerned with the effect of turning process parameters (cutting speed, feed rate, and depth of cut) and distance from the center of work piece as input variables on the chip micro-hardness as response or output. Three experiments were conducted; they were used to investigate the chip micro-hardness behavior at diameter of work piece for 30[mm], 40[mm], and 50[mm]. Response surface methodology (R.S.M) is used to determine and present the cause and effect of the relationship between true mean response and input control variables influencing the response as a two or three dimensional hyper surface. R.S.M has been used for designing a three factor with five level central composite rotatable factors design in order to construct statistical models capable of accurate prediction of responses. The results obtained showed that the application of R.S.M can predict the effect of machining parameters on chip micro-hardness. The five level factorial designs can be employed easily for developing statistical models to predict chip micro-hardness by controllable machining parameters. Results obtained showed that the combined effect of cutting speed at it?s lower level, feed rate and depth of cut at their higher values, and larger work piece diameter can result increasing chi micro-hardness.
Abstract: In this paper, a new efficient method for load balancing in low voltage distribution systems is presented. The proposed method introduces an improved Leap-frog method for optimization. The proposed objective function includes the difference between three phase currents, as well as two other terms to provide the integer property of the variables; where the latter are the status of the connection of loads to different phases. Afterwards, a new algorithm is supplemented to undertake the integer values for the load connection status. Finally, the method is applied to different parts of Tabriz low voltage network, where the results have shown the good performance of the proposed method.
Abstract: This paper considers the problem of Null-Steering beamforming using Neural Network (NN) approach for antenna array system. Two cases are presented. First, unlike the other authors, the estimated Direction Of Arrivals (DOAs) are used for antenna array weights NN-based determination and the imprecise DOAs estimations are taken into account. Second, the blind null-steering beamforming is presented. In this case the antenna array outputs are presented at the input of the NN without DOAs estimation. The results of computer simulations will show much better relative mean error performances of the first NN approach compared to the NNbased blind beamforming.
Abstract: In this study the behavior of interlaminar fracture of
carbon-epoxy thermoplastic laminated composite is investigated
numerically and experimentally. Tests are performed with Arcan
specimens. Testing with Arcan specimen gives the opportunity of
utilizing just one kind of specimen for extracting fracture properties
for mode I, mode II and different mixed mode ratios of materials with
exerting load via different loading angles. Variation of loading angles
in range of 0-90° made possible to achieve different mixed mode
ratios. Correction factors for various conditions are obtained from
ABAQUS 2D finite element models which demonstrate the finite
shape of Arcan specimens used in this study. Finally, applying the
correction factors to critical loads obtained experimentally, critical
interlaminar fracture toughness of this type of carbon- epoxy
composite has been attained.
Abstract: This paper describes the shape optimization of impeller
blades for a anti-heeling bidirectional axial flow pump used in ships.
In general, a bidirectional axial pump has an efficiency much lower
than the classical unidirectional pump because of the symmetry of the
blade type. In this paper, by focusing on a pump impeller, the shape of
blades is redesigned to reach a higher efficiency in a bidirectional axial
pump. The commercial code employed in this simulation is CFX v.13.
CFD result of pump torque, head, and hydraulic efficiency was
compared. The orthogonal array (OA) and analysis of variance
(ANOVA) techniques and surrogate model based optimization using
orthogonal polynomial, are employed to determine the main effects
and their optimal design variables. According to the optimal design,
we confirm an effective design variable in impeller blades and explain
the optimal solution, the usefulness for satisfying the constraints of
pump torque and head.
Abstract: The multiple traveling salesman problem (mTSP) can be used to model many practical problems. The mTSP is more complicated than the traveling salesman problem (TSP) because it requires determining which cities to assign to each salesman, as well as the optimal ordering of the cities within each salesman's tour. Previous studies proposed that Genetic Algorithm (GA), Integer Programming (IP) and several neural network (NN) approaches could be used to solve mTSP. This paper compared the results for mTSP, solved with Genetic Algorithm (GA) and Nearest Neighbor Algorithm (NNA). The number of cities is clustered into a few groups using k-means clustering technique. The number of groups depends on the number of salesman. Then, each group is solved with NNA and GA as an independent TSP. It is found that k-means clustering and NNA are superior to GA in terms of performance (evaluated by fitness function) and computing time.
Abstract: Chemical detection is still a continuous challenge when
it comes to designing single-walled carbon nanotube (SWCNT)
sensors with high selectivity, especially in complex chemical
environments. A perfect example of such an environment would be in
thermally oxidized soybean oil. At elevated temperatures, oil oxidizes
through a series of chemical reactions which results in the formation of
monoacylglycerols, diacylglycerols, oxidized triacylglycerols, dimers,
trimers, polymers, free fatty acids, ketones, aldehydes, alcohols,
esters, and other minor products. In order to detect the rancidity of
oxidized soybean oil, carbon nanotube chemiresistor sensors have
been coated with polyethylenimine (PEI) to enhance the sensitivity
and selectivity. PEI functionalized SWCNTs are known to have a high
selectivity towards strong electron withdrawing molecules. The
sensors were very responsive to different oil oxidation levels and
furthermore, displayed a rapid recovery in ambient air without the
need of heating or UV exposure.
Abstract: In this paper, we propose the Modified Synchronous Detection (MSD) Method for determining the reference compensating currents of the shunt active power filter under non sinusoidal voltages conditions. For controlling the inverter switching we used the PI regulator. The numerical simulation results, using Power System Blockset Toolbox PSB of Matlab, from a complete structure, are presented and discussed.
Abstract: This paper presents an optimization technique to economic load dispatch (ELD) problems with considering the daily load patterns and generator constraints using a particle swarm optimization (PSO). The objective is to minimize the fuel cost. The optimization problem is subject to system constraints consisting of power balance and generation output of each units. The application of a constriction factor into PSO is a useful strategy to ensure convergence of the particle swarm algorithm. The proposed method is able to determine, the output power generation for all of the power generation units, so that the total constraint cost function is minimized. The performance of the developed methodology is demonstrated by case studies in test system of fifteen-generation units. The results show that the proposed algorithm scan give the minimum total cost of generation while satisfying all the constraints and benefiting greatly from saving in power loss reduction
Abstract: Science and technology of ultrasonic is widely used in
recent years for industrial and medicinal application. The acoustical
properties of 2-mercapto substituted pyrimidines viz.,2- Mercapto-4-
(2’,4’ –dichloro phenyl) – 6-(2’ – hydroxyl -4’ –methyl-5’ –
chlorophenyl) pyrimidine and 2 –Mercapto – 4-(4’ –chloro phenyl) –
6-(2’ – hydroxyl -4’ –methyl-5’ –chlorophenyl) pyrimidine have been
investigated from the ultrasonic velocity and density measurements at
different concentration and different % in dioxane-water mixture at
305K. The adiabatic compressibility (βs), acoustic impedance (Z),
intermolecular free length (Lf), apparent molar volume(ϕv) and
relative association (RA) values have been calculated from the
experimental data of velocity and density measurement at
concentration range of 0.01- 0.000625 mol/lit and 70%,75% and 80%
dioxane water mixture. These above parameters are used to discuss
the structural and molecular interactions.
Abstract: This paper investigates the effectiveness of the use of
seismic isolation devices on the overall 3D seismic response of
curved highway viaducts with an emphasis on expansion joints.
Furthermore, an evaluation of the effectiveness of the use of cable
restrainers is presented. For this purpose, the bridge seismic
performance has been evaluated on four different radii of curvature,
considering two cases: restrained and unrestrained curved viaducts.
Depending on the radius of curvature, three-dimensional non-linear
dynamic analysis shows the vulnerability of curved viaducts to
pounding and deck unseating damage. In this study, the efficiency of
using LRB supports combined with cable restrainers on curved
viaducts is demonstrated, not only by reducing in all cases the
possible damage, but also by providing a similar behavior in the
viaducts despite of curvature radius.
Abstract: The simple methods used to plan and measure non
patterned production system are developed from the basic definition
of working efficiency. Processing time is assigned as the variable
and used to write the equation of production efficiency.
Consequently, such equation is extensively used to develop the
planning method for production of interest using one-dimensional
stock cutting problem. The application of the developed method
shows that production efficiency and production planning can be
determined effectively.
Abstract: The regulatory competence of blood glucose homeostasis might determine the degree of academic performance. The aim of this study was to produce a model of students' alcohol use based on glucose homeostasis control and cognitive functions that might define the pathogenetic mechanism of alcohol's effect on academic performance. The study took six hours and thirty minutes on fasting, involving thirteen male students. Disturbances in cognitive functions, precisely a decrease in the effectiveness of active attention and a faster development of fatigue after four to six hours of mental work in alcohol users, compared to abstainers was statistically proven. These disturbances in alcohol users were retained even after seven to ten days of moderate alcohol use and might be the reason for the low academic performances among students who use alcoholic beverages.
Abstract: Infrared communication in the wavelength band 780-
950 nm is very suitable for short-range point-to-point communications.
It is a good choice for vehicle-to-vehicle communication in several
intelligent-transportation-system (ITS) applications such as cooperative
driving, collision warning, and pileup-crash prevention. In this
paper, with the aid of a physical model established in our previous
works, we explore the communication area of an infrared intervehicle
communication system utilizing a typical low-cost cormmercial lightemitting
diodes (LEDs) as the emitter and planar p-i-n photodiodes
as the receiver. The radiation pattern of the emitter fabricated by
aforementioned LEDs and the receiving pattern of the receiver are
approximated by a linear combination of cosinen functions. This
approximation helps us analyze the system performance easily. Both
multilane straight-road conditions and curved-road conditions with
various radius of curvature are taken into account. The condition of
a small car communicating with a big truck, i.e., there is a vertical
mounting height difference between the emitter and the receiver, is
also considered. Our results show that the performance of the system
meets the requirement of aforementioned ITS applications in terms
of the communication area.
Abstract: A numerical study is presented on convective heat transfer in enclosures. The results are addressed to automotive headlights containing new-age light sources like Light Emitting Diodes (LED). The heat transfer from the heat source (LED) to the enclosure walls is investigated for mixed convection as interaction of the forced convection flow from an inlet and an outlet port and the natural convection at the heat source. Unlike existing studies, inlet and outlet port are thermally coupled and do not serve to remove hot fluid. The input power of the heat source is expressed by the Rayleigh number. The internal position of the heat source, the aspect ratio of the enclosure, and the inclination angle of one wall are varied. The results are given in terms of the global Nusselt number and the enclosure Nusselt number that characterize the heat transfer from the source and from the interior fluid to the enclosure walls, respectively. It is found that the heat transfer from the source to the fluid can be maximized if the source is placed in the main stream from the inlet to the outlet port. In this case, the Reynolds number and heat source position have the major impact on the heat transfer. A disadvantageous position has been found where natural and forced convection compete each other. The overall heat transfer from the source to the wall increases with increasing Reynolds number as well as with increasing aspect ratio and decreasing inclination angle. The heat transfer from the interior fluid to the enclosure wall increases upon decreasing the aspect ratio and increasing the inclination angle. This counteracting behaviour is caused by the variation of the area of the enclosure wall. All mixed convection results are compared to the natural convection limit.
Abstract: In two studies we tested the hypothesis that the
appropriate linguistic formulation of a deontic rule – i.e. the
formulation which clarifies the monadic nature of deontic operators
- should produce more correct responses than the conditional
formulation in Wason selection task. We tested this assumption by
presenting a prescription rule and a prohibition rule in conditional
vs. proper deontic formulation. We contrasted this hypothesis with
two other hypotheses derived from social contract theory and
relevance theory. According to the first theory, a deontic rule
expressed in terms of cost-benefit should elicit a cheater detection
module, sensible to mental states attributions and thus able to
discriminate intentional rule violations from accidental rule
violations. We tested this prevision by distinguishing the two types
of violations. According to relevance theory, performance in
selection task should improve by increasing cognitive effect and
decreasing cognitive effort. We tested this prevision by focusing
experimental instructions on the rule vs. the action covered by the
rule. In study 1, in which 480 undergraduates participated, we
tested these predictions through a 2 x 2 x 2 x 2 (type of the rule x
rule formulation x type of violation x experimental instructions)
between-subjects design. In study 2 – carried out by means of a 2 x
2 (rule formulation x type of violation) between-subjects design -
we retested the hypothesis of rule formulation vs. the cheaterdetection
hypothesis through a new version of selection task in
which intentional vs. accidental rule violations were better
discriminated. 240 undergraduates participated in this study.
Results corroborate our hypothesis and challenge the contrasting
assumptions. However, they show that the conditional formulation
of deontic rules produces a lower performance than what is
reported in literature.
Abstract: A conjugate heat transfer for steady two-dimensional
mixed convection with magnetic hydrodynamic (MHD) flow of an
incompressible quiescent fluid over an unsteady thermal forming
stretching sheet has been studied. A parameter, M, which is used to
represent the dominance of the magnetic effect has been presented in
governing equations. The similar transformation and an implicit
finite-difference method have been used to analyze the present
problem. The numerical solutions of the flow velocity distributions,
temperature profiles, the wall unknown values of f''(0) and '(θ (0) for
calculating the heat transfer of the similar boundary-layer flow are
carried out as functions of the unsteadiness parameter (S), the Prandtl
number (Pr), the space-dependent parameter (A) and
temperature-dependent parameter (B) for heat source/sink and the
magnetic parameter (M). The effects of these parameters have also
discussed. At the results, it will produce greater heat transfer effect
with a larger Pr and M, S, A, B will reduce heat transfer effects. At
last, conjugate heat transfer for the free convection with a larger G has
a good heat transfer effect better than a smaller G=0.
Abstract: Experiments with pumpkin-rowanberry marmalade
candies were carried out at the Faculty of Food Technology of the
Latvia University of Agriculture. The objective of this investigation
was to evaluate the quality changes of pumpkin-rowanberry
marmalade candies packed in different packaging materials during
the storage of 15 weeks, and to find the most suitable packaging
material for prolongation of low sugar marmalade candies shelf-life.
An active packaging in combination with modified atmosphere
(MAP, CO2 100%) was examined and compared with traditional
packaging in air ambiance. Polymer Multibarrier 60 and paper bags
were used. Influence of iron based oxygen absorber in sachets of 500
cc obtained from Mitsubishi Gas Chemical Europe Ageless® on the
marmalade candies’ quality was tested during shelf life. Samples of
80±5 g were packaged in polymer pouches (110 mm x 110 mm),
hermetically sealed by MULTIVAC C300 vacuum chamber machine,
and stored in a room temperature +21±0.5 °C. The physiochemical
properties –moisture content, hardness, aw, pH, changes of
atmosphere content (CO2 and O2), ascorbic acid, total carotenoids,
total phenols in headspace of packs, and microbial conditions were
analysed before packaging and in the 1st, 3rd , 5th, 8th, 11th and 15th
weeks of storage.