Abstract: Many applications require surface modification and
micro-structuring of polymers. For these purposes is mainly used
ultraviolet (UV) radiation from excimer lamps or excimer lasers.
However, these sources have a decided disadvantage - degrading the
polymer deep inside due to relatively big radiation penetration depth
which may exceed 100 μm. In contrast, extreme ultraviolet (EUV)
radiation is absorbed in a layer approximately 100 nm thick only. In
this work, the radiation from a discharge-plasma EUV source (with
wavelength 46.9 nm) based on a capillary discharge driver is focused
with a spherical Si/Sc multilayer mirror for surface modification of
PMMA sample or thin gold layer (thickness about 40 nm). It was
found that the focused EUV laser beam is capable by one shot to
ablate PMMA or layer of gold, even if the focus is significantly
influenced by astigmatism.
Abstract: Recently, Thai education system is engaged in serious and promising reforms. One of the crucial elements in most of these educational reforms is the teacher professional development. Teachers today are under growing pressure to perform. However, most new teachers are not adequately prepared to meet the expectation. Consequently, this paper seeks to investigate the opinion of mentor teachers and university supervisors about professional development in the aspect of learning management skill of the preservice teachers in Rajabhat Universities, then compare the opinion between the mentor teachers and university supervisors about professional development in the aspect of learning management skill of the pre-service teachers. The study involved a cohort of 40 university supervisors and 77 mentor teachers. The research concludes by showing that mentor teachers viewed pre-service teacher as a professional teacher with an effective learning management skill. However, in the perspective of the university supervisor, pre-service teachers still have inadequate learning management skill.
Abstract: This paper presents a methodology to harvest the kinetic energy of the raindrops using piezoelectric devices. In the study 1m×1m PVDF (Polyvinylidene fluoride) piezoelectric membrane, which is fixed by the four edges, is considered for the numerical simulation on deformation of the membrane due to the impact of the raindrops. Then according to the drop size of the rain, the simulation is performed classifying the rainfall types into three categories as light stratiform rain, moderate stratiform rain and heavy thundershower. The impact force of the raindrop is dependent on the terminal velocity of the raindrop, which is a function of raindrop diameter. The results were then analyzed to calculate the harvestable energy from the deformation of the piezoelectric membrane.
Abstract: In this study, control performance of a smart base
isolation system consisting of a friction pendulum system (FPS) and a
magnetorheological (MR) damper has been investigated. A fuzzy
logic controller (FLC) is used to modulate the MR damper so as to
minimize structural acceleration while maintaining acceptable base
displacement levels. To this end, a multi-objective optimization
scheme is used to optimize parameters of membership functions and
find appropriate fuzzy rules. To demonstrate effectiveness of the
proposed multi-objective genetic algorithm for FLC, a numerical
study of a smart base isolation system is conducted using several
historical earthquakes. It is shown that the proposed method can find
optimal fuzzy rules and that the optimized FLC outperforms not only a
passive control strategy but also a human-designed FLC and a
conventional semi-active control algorithm.
Abstract: Network on Chip (NoC) has emerged as a promising
on chip communication infrastructure. Three Dimensional Integrate
Circuit (3D IC) provides small interconnection length between layers
and the interconnect scalability in the third dimension, which can
further improve the performance of NoC. Therefore, in this paper,
a hierarchical cluster-based interconnect architecture is merged with
the 3D IC. This interconnect architecture significantly reduces the
number of long wires. Since this architecture only has approximately
a quarter of routers in 3D mesh-based architecture, the average
number of hops is smaller, which leads to lower latency and higher
throughput. Moreover, smaller number of routers decreases the area
overhead. Meanwhile, some dual links are inserted into the bottlenecks
of communication to improve the performance of NoC.
Simulation results demonstrate our theoretical analysis and show the
advantages of our proposed architecture in latency, throughput and
area, when compared with 3D mesh-based architecture.
Abstract: Considering payload, reliability, security and operational lifetime as major constraints in transmission of images we put forward in this paper a steganographic technique implemented at the physical layer. We suggest transmission of Halftoned images (payload constraint) in wireless sensor networks to reduce the amount of transmitted data. For low power and interference limited applications Turbo codes provide suitable reliability. Ensuring security is one of the highest priorities in many sensor networks. The Turbo Code structure apart from providing forward error correction can be utilized to provide for encryption. We first consider the Halftoned image and then the method of embedding a block of data (called secret) in this Halftoned image during the turbo encoding process is presented. The small modifications required at the turbo decoder end to extract the embedded data are presented next. The implementation complexity and the degradation of the BER (bit error rate) in the Turbo based stego system are analyzed. Using some of the entropy based crypt analytic techniques we show that the strength of our Turbo based stego system approaches that found in the OTPs (one time pad).
Abstract: In a complex project environment, project teams face
multi-dimensional communication problems that can ultimately lead
to project breakdown. Team Performance varies in Face-to-Face
(FTF) environment versus groups working remotely in a computermediated
communication (CMC) environment. A brief review of the
Input_Process_Output model suggested by James E. Driskell, Paul H.
Radtke and Eduardo Salas in “Virtual Teams: Effects of
Technological Mediation on Team Performance (2003)", has been
done to develop the basis of this research. This model theoretically
analyzes the effects of technological mediation on team processes,
such as, cohesiveness, status and authority relations, counternormative
behavior and communication. An empirical study
described in this paper has been undertaken to test the
“cohesiveness" of diverse project teams in a multi-national
organization. This study uses both quantitative and qualitative
techniques for data gathering and analysis. These techniques include
interviews, questionnaires for data collection and graphical data
representation for analyzing the collected data. Computer-mediated
technology may impact team performance because of difference in
cohesiveness among teams and this difference may be moderated by
factors, such as, the type of communication environment, the type of
task and the temporal context of the team. Based on the reviewed
model, sets of hypotheses are devised and tested. This research,
reports on a study that compared team cohesiveness among virtual
teams using CMC and non-CMC communication mediums. The
findings suggest that CMC can help virtual teams increase team
cohesiveness among their members, making CMC an effective
medium for increasing productivity and team performance.
Abstract: This paper features the kinematic modelling of a 5-axis stationary articulated robot arm which is used for doing successful robotic manipulation task in its workspace. To start with, a 5-axes articulated robot was designed entirely from scratch and from indigenous components and a brief kinematic modelling was performed and using this kinematic model, the pick and place task was performed successfully in the work space of the robot. A user friendly GUI was developed in C++ language which was used to perform the successful robotic manipulation task using the developed mathematical kinematic model. This developed kinematic model also incorporates the obstacle avoiding algorithms also during the pick and place operation.
Abstract: A robust wheel slip controller for electric vehicles is
introduced. The proposed wheel slip controller exploits the dynamics
of electric traction drives and conventional hydraulic brakes for
achieving maximum energy efficiency and driving safety. Due to
the control of single wheel traction motors in combination with a
hydraulic braking system, it can be shown, that energy recuperation
and vehicle stability control can be realized simultaneously. The
derivation of a sliding mode wheel slip controller accessing two
drivetrain actuators is outlined and a comparison to a conventionally
braked vehicle is shown by means of simulation.
Abstract: In a travelling wave thermoacoustic device, the
regenerator sandwiched between a pair of (hot and cold) heat
exchangers constitutes the so-called thermoacoustic core, where the
thermoacoustic energy conversion from heat to acoustic power takes
place. The temperature gradient along the regenerator caused by the
two heat exchangers excites and maintains the acoustic wave in the
resonator. The devices are called travelling wave thermoacoustic
systems because the phase angle difference between the pressure and
velocity oscillation is close to zero in the regenerator. This paper
presents the construction and testing of a thermoacoustic engine
equipped with a ceramic regenerator, made from a ceramic material
that is usually used as catalyst substrate in vehicles- exhaust systems,
with fine square channels (900 cells per square inch). The testing
includes the onset temperature difference (minimum temperature
difference required to start the acoustic oscillation in an engine), the
acoustic power output, thermal efficiency and the temperature profile
along the regenerator.
Abstract: The adaptive power control of Code Division Multiple
Access (CDMA) communications using Remote Radio Head
(RRH) between multiple Unmanned Aerial Vehicles (UAVs) with
a link-budget based Signal-to-Interference Ratio (SIR) estimate is
applied to four inner loop power control algorithms. It is concluded
that Base Station (BS) can calculate not only UAV distance using
linearity between speed and Consecutive Transmit-Power-Control
Ratio (CTR) of Adaptive Step-size Closed Loop Power Control (ASCLPC),
Consecutive TPC Ratio Step-size Closed Loop Power Control
(CS-CLPC), Fixed Step-size Power Control (FSPC), but also UAV
position with Received Signal Strength Indicator (RSSI) ratio of
RRHs.
Abstract: In this work, we perform numerical simulation of fluid
mixing in a floor-grooved micro-channel with wavy sidewalls which
may impose perturbation on the helical flow induced by the slanted
grooves on the channel floor. The perturbation is caused by separation
vortices in the recesses of the wavy-walled channel as the Reynolds
number is large enough. The results show that the effects of the wavy
sidewalls of the present micromixer on the enhancement of fluid
mixing increase with the increase of Reynolds number. The degree of
mixing increases with the increase of the corrugation angle, until the
angle is greater than 45 degrees. Besides, the pumping pressure of the
micromixer increases with the increase of the corrugation angle
monotonically. Therefore, we would suggest setting the corrugation
angle of the wavy sidewalls to be 45 degrees.
Abstract: This paper investigates experimental studies on
vibration suppression for a cantilever beam using an
Electro-Rheological (ER) sandwich shock absorber. ER fluid (ERF) is a
class of smart materials that can undergo significant reversible changes
immediately in its rheological and mechanical properties under the
influence of an applied electric field. Firstly, an ER sandwich beam is
fabricated by inserting a starch-based ERF into a hollow composite
beam. At the same time, experimental investigations are focused on the
frequency response of the ERF sandwich beam. Second, the ERF
sandwich beam is attached to a cantilever beam to become as a shock
absorber. Finally, a fuzzy semi-active vibration control is designed to
suppress the vibration of the cantilever beam via the ERF sandwich
shock absorber. To check the consistency of the proposed fuzzy
controller, the real-time implementation validated the performance of
the controller.
Abstract: This paper studies mixed-mode fracture mechanics in
rock based on experimental and numerical analyses. Experiments
were performed on sharp-cracked specimens using the modified
Arcan specimen test loading device. The modified Arcan specimen
test was, in association with a special loading device, an appropriate
apparatus for experimental mixed-mode fracture analysis. By
varying the loading angle from 0° to 90°, pure mode-I, pure mode-II
and a wide range of mixed-mode data were obtained experimentally.
Using the finite element results, correction factors applied to the
rectangular fracture specimen. By employing experimentally
measured critical loads and the aid of the finite element method,
mixed-mode fracture toughness for the limestone under consideration
determined.
Abstract: This paper presents a integer frequency offset (IFO)
estimation scheme for the 3GPP long term evolution (LTE) downlink
system. Firstly, the conventional joint detection method for IFO and
sector cell index (CID) information is introduced. Secondly, an IFO
estimation without explicit sector CID information is proposed, which
can operate jointly with the proposed IFO estimation and reduce
the time delay in comparison with the conventional joint method.
Also, the proposed method is computationally efficient and has almost
similar performance in comparison with the conventional method over
the Pedestrian and Vehicular channel models.
Abstract: In the numerical solution of the forward dynamics of a
multibody system, the positions and velocities of the bodies in the
system are obtained first. With the information of the system state
variables at each time step, the internal and external forces acting on
the system are obtained by appropriate contact force models if the
continuous contact method is used instead of a discrete contact
method. The local deformation of the bodies in contact, represented
by penetration, is used to compute the contact force. The ability and
suitability with current cylindrical contact force models to describe
the contact between bodies with cylindrical geometries with
particular focus on internal contacting geometries involving low
clearances and high loads simultaneously is discussed in this paper.
A comparative assessment of the performance of each model under
analysis for different contact conditions, in particular for very
different penetration and clearance values, is presented. It is
demonstrated that some models represent a rough approximation to
describe the conformal contact between cylindrical geometries
because contact forces are underestimated.
Abstract: The present study is concerned with effect of exciting
boundary layer on increase in heat transfer from flat surfaces. As any
increase in heat transfer between a fluid inside a face and another one
outside of it can cause an increase in some equipment's efficiency, so
at this present we have tried to increase the wall's heat transfer
coefficient by exciting the fluid boundary layer. By a collision
between flow and the placed block at the fluid way, the flow pattern
and the boundary layer stability will change. The flow way inside the
channel is simulated as a 2&3-dimensional channel by Gambit
TM
software.
With studying the achieved results by this simulation for the flow
way inside the channel with a block coordinating with Fluent
TM
software, it's determined that the figure and dimensions of the exciter
are too important for exciting the boundary layer so that any increase
in block dimensions in vertical side against the flow and any
reduction in its dimensions at the flow side can increase the average
heat transfer coefficient from flat surface and increase the flow
pressure loss. Using 2&3-dimensional analysis on exciting the flow at
the flow way inside a channel by cylindrical block at the same time
with the external flow, we came to this conclusion that the heat flux
transferred from the surface, is increased considerably in terms of the
condition without excitation. Also, the k-e turbulence model is used.
Abstract: In this paper, we present the region based hidden Markov random field model (RBHMRF), which encodes the characteristics of different brain regions into a probabilistic framework for brain MR image segmentation. The recently proposed TV+L1 model is used for region extraction. By utilizing different spatial characteristics in different brain regions, the RMHMRF model performs beyond the current state-of-the-art method, the hidden Markov random field model (HMRF), which uses identical spatial information throughout the whole brain. Experiments on both real and synthetic 3D MR images show that the segmentation result of the proposed method has higher accuracy compared to existing algorithms.
Abstract: In this paper, a novel and fast algorithm for segmental
and subsegmental lung vessel segmentation is introduced using
Computed Tomography Angiography images. This process is quite
important especially at the detection of pulmonary embolism, lung
nodule, and interstitial lung disease. The applied method has been
realized at five steps. At the first step, lung segmentation is achieved.
At the second one, images are threshold and differences between the
images are detected. At the third one, left and right lungs are gathered
with the differences which are attained in the second step and Exact
Lung Image (ELI) is achieved. At the fourth one, image, which is
threshold for vessel, is gathered with the ELI. Lastly, identifying and
segmentation of segmental and subsegmental lung vessel have been
carried out thanks to image which is obtained in the fourth step. The
performance of the applied method is found quite well for
radiologists and it gives enough results to the surgeries medically.
Abstract: In this work a new offline signature recognition system
based on Radon Transform, Fractal Dimension (FD) and Support Vector Machine (SVM) is presented. In the first step, projections of
original signatures along four specified directions have been performed using radon transform. Then, FDs of four obtained
vectors are calculated to construct a feature vector for each
signature. These vectors are then fed into SVM classifier for recognition of signatures. In order to evaluate the effectiveness of
the system several experiments are carried out. Offline signature
database from signature verification competition (SVC) 2004 is used
during all of the tests. Experimental result indicates that the proposed method achieved high accuracy rate in signature recognition.