Abstract: The continued interest in the use of distributed generation in recent years is leading to the growth in number of distributed generators connected to distribution networks. Steady state voltage rise resulting from the connection of these generators can be a major obstacle to their connection at lower voltage levels. The present electric distribution network is designed to keep the customer voltage within tolerance limit. This may require a reduction in connectable generation capacity, under utilization of appropriate generation sites. Thus distribution network operators need a proper voltage regulation method to allow the significant integration of distributed generation systems to existing network. In this work a voltage rise problem in a typical distribution system has been studied. A method for voltage regulation of distribution system with multiple DG system by coordinated operation distributed generator, capacitor and OLTC has been developed. A sensitivity based analysis has been carried out to determine the priority for individual generators in multiple DG environment. The effectiveness of the developed method has been evaluated under various cases through simulation results.
Abstract: This paper develops driver reaction-time models for
car-following analysis based on human factors. The reaction time
was classified as brake-reaction time (BRT) and
acceleration/deceleration reaction time (ADRT). The BRT occurs
when the lead vehicle is barking and its brake light is on, while the
ADRT occurs when the driver reacts to adjust his/her speed using the
gas pedal only. The study evaluates the effect of driver
characteristics and traffic kinematic conditions on the driver reaction
time in a car-following environment. The kinematic conditions
introduced urgency and expectancy based on the braking behaviour
of the lead vehicle at different speeds and spacing. The kinematic
conditions were used for evaluating the BRT and are classified as
normal, surprised, and stationary. Data were collected on a driving
simulator integrated into a real car and included the BRT and ADRT
(as dependent variables) and driver-s age, gender, driving experience,
driving intensity (driving hours per week), vehicle speed, and
spacing (as independent variables). The results showed that there was
a significant difference in the BRT at normal, surprised, and
stationary scenarios and supported the hypothesis that both urgency
and expectancy had significant effects on BRT. Driver-s age, gender,
speed, and spacing were found to be significant variables for the
BRT in all scenarios. The results also showed that driver-s age and
gender were significant variables for the ADRT. The research
presented in this paper is part of a larger project to develop a driversensitive
in-vehicle rear-end collision warning system.
Abstract: In order to calculate the flexural strength of
normal-strength concrete (NSC) beams, the nonlinear actual concrete
stress distribution within the compression zone is normally replaced
by an equivalent rectangular stress block, with two coefficients of α
and β to regulate the intensity and depth of the equivalent stress
respectively. For NSC beams design, α and β are usually assumed
constant as 0.85 and 0.80 in reinforced concrete (RC) codes. From an
earlier investigation of the authors, α is not a constant but significantly
affected by flexural strain gradient, and increases with the increasing
of strain gradient till a maximum value. It indicates that larger
concrete stress can be developed in flexure than that stipulated by
design codes. As an extension and application of the authors- previous
study, the modified equivalent concrete stress block is used here to
produce a series of design charts showing the maximum design limits
of flexural strength and ductility of singly- and doubly- NSC beams,
through which both strength and ductility design limits are improved
by taking into account strain gradient effect.
Abstract: This paper identifies five key design characteristics of
production scheduling software systems in printed circuit board (PCB) manufacturing. The authors consider that, in addition to an effective scheduling engine, a scheduling system should be able to
process a preventative maintenance calendar, to give the user the
flexibility to handle data using a variety of electronic sources, to run
simulations to support decision-making, and to have simple and
customisable graphical user interfaces. These design considerations
were the result of a review of academic literature, the evaluation of
commercial applications and a compilation of requirements of a PCB manufacturer. It was found that, from those systems that were evaluated, those that effectively addressed all five characteristics
outlined in this paper were the most robust of all and could be used in
PCB manufacturing.
Abstract: There has been a growing interest in the field of
bio-mimetic robots that resemble the shape of an insect or an aquatic
animal, among many others. One bio-mimetic robot serves the
purpose of exploring pipelines, spotting any troubled areas or
malfunctions and reporting its data. Moreover, the robot is able to
prepare for and react to any abnormal routes in the pipeline. In order
to move effectively inside a pipeline, the robot-s movement will
resemble that of a lizard. When situated in massive pipelines with
complex routes, the robot places fixed sensors in several important
spots in order to complete its monitoring. This monitoring task is to
prevent a major system failure by preemptively recognizing any minor
or partial malfunctions. Areas uncovered by fixed sensors are usually
impossible to provide real-time observation and examination, and thus
are dependant on periodical offline monitoring. This paper provides
the Monitoring System that is able to monitor the entire area of
pipelines–with and without fixed sensors–by using the bio-mimetic
robot.
Abstract: Power-line networks are widely used today for broadband data transmission. However, due to multipaths within the broadband power line communication (BPLC) systems owing to stochastic changes in the network load impedances, branches, etc., network or channel capacity performances are affected. This paper attempts to investigate the performance of typical medium voltage channels that uses Orthogonal Frequency Division Multiplexing (OFDM) techniques with Quadrature Amplitude Modulation (QAM) sub carriers. It has been observed that when the load impedances are different from line characteristic impedance channel performance decreases. Also as the number of branches in the link between the transmitter and receiver increases a loss of 4dB/branch is found in the signal to noise ratio (SNR). The information presented in the paper could be useful for an appropriate design of the BPLC systems.
Abstract: Connected dominating set (CDS) problem in unit disk
graph has signi£cant impact on an ef£cient design of routing protocols
in wireless sensor networks, where the searching space for a
route is reduced to nodes in the set. A set is dominating if all the
nodes in the system are either in the set or neighbors of nodes in the
set. In this paper, a simple and ef£cient heuristic method is proposed
for £nding a minimum connected dominating set (MCDS) in ad hoc
wireless networks based on the new parameter support of vertices.
With this parameter the proposed heuristic approach effectively
£nds the MCDS of a graph. Extensive computational experiments
show that the proposed approach outperforms the recently proposed
heuristics found in the literature for the MCD
Abstract: Linear stability of wake-shear layers in two-phase
shallow flows is analyzed in the present paper. Stability analysis is
based on two-dimensional shallow water equations. It is assumed that
the fluid contains uniformly distributed solid particles. No dynamic
interaction between the carrier fluid and particles is expected in the
initial moment. Linear stability curves are obtained for different
values of the particle loading parameter, the velocity ratio and the
velocity deficit. It is shown that the increase in the velocity ratio
destabilizes the flow. The particle loading parameter has a stabilizing
effect on the flow. The role of the velocity deficit is also
destabilizing: the increase of the velocity deficit leads to less stable
flow.
Abstract: This research focuses on the use of a recommender
system in decision support by means of a used car dealer case study
in Bangkok Metropolitan. The goal is to develop an effective used car
purchasing system for dealers based on the above premise. The
underlying principle rests on content-based recommendation from a
set of usability surveys. A prototype was developed to conduct
buyers- survey selected from 5 experts and 95 general public. The
responses were analyzed to determine the mean and standard
deviation of buyers- preference. The results revealed that both groups
were in favor of using the proposed system to assist their buying
decision. This indicates that the proposed system is meritorious to
used car dealers.
Abstract: The effect of cassava root ensiled with cassava top or
legumes on voluntary feed intake and milk production were
determined in 12 dairy cows using a 4×3 change-over design.
Experimental period were 30 days long and consisted of 14 days of
adaptation. Silage was prepared from cassava root mixed with
cassava top or legumes at ratio 60:40. Cows were allotted at random
to receive ad libitum one of four rations: T1) control, T2) cassava
root +cassava top-silages, T3) cassava root +hamata - silages and T4)
cassava root +Thapra stylo-silages.
The dry matter intake (BW0.75) was higher (P< 0.05) in cow fed
with silages diets compared with T1. However, the intake of T2 was
higher among treatments. Milk production was lowest in cow fed
with T1. Among silages based diets, milk production was not
significantly different but 4%FCM was higher in cow fed T2. Milk
compositions were not affected by feeding diets.
It is concluded that feeding cassava root ensiled with its leaves as
a supplement increased dry matter intake and significantly improved
4%FCM. The combination of cassava root and legume silages did not
improve the feed intake but did increase the milk production.
Abstract: A study was carried out at the Rice Research Institute of Iran (RRII) to investigate the effect of rollers differential peripheral speed of commercial rubber roll husker and paddy moisture content on the husking index and percentage of broken rice. The experiment was conducted at six levels of rollers differential speed (1.5, 2.2, 2.9, 3.6, 4.3 and 5 m/s) and three levels of paddy moisture content (8-9, 10-11 and 12-13% w.b.). Two common paddy varieties namely, Binam and Khazer, were selected for this study. Results revealed that the effect of rollers differential speed and moisture content significantly (P
Abstract: In this paper, experimental testing and numerical analysis were used to investigate the effect of tube thickness on the face bending for concrete filled hollow sections connected to other structural members using Extended Hollobolts. Six samples were tested experimentally by applying pull-out load on the bolts. These samples were designed to fail by column face bending. The main variable in all tests is the column face thickness. Finite element analyses were also performed using ABAQUS 6.11 to extend the experimental results and to quantify the effect of column face thickness. Results show that, the column face thickness has a clear impact on the connection strength and stiffness. However, the amount of improvement in the connection stiffness by changing the column face thickness from 5mm to 6.3mm seems to be higher than that when increasing it from 6.3mm to 8mm. The displacement at which the bolts start pulling-out from their holes increased with the use of thinner column face due to the high flexibility of the section. At the ultimate strength, the yielding of the column face propagated to the column corner and there was no yielding in its walls. After the ultimate resistance is reached, the propagation of the yielding was mainly in the column face with a miner yielding in the walls.
Abstract: A full six degrees of freedom (6-DOF) flight dynamics
model is proposed for the accurate prediction of short and long-range
trajectories of high spin and fin-stabilized projectiles via atmospheric
flight to final impact point. The projectiles is assumed to be both rigid
(non-flexible), and rotationally symmetric about its spin axis launched
at low and high pitch angles. The mathematical model is based on the
full equations of motion set up in the no-roll body reference frame and
is integrated numerically from given initial conditions at the firing
site. The projectiles maneuvering motion depends on the most
significant force and moment variations, in addition to wind and
gravity. The computational flight analysis takes into consideration the
Mach number and total angle of attack effects by means of the
variable aerodynamic coefficients. For the purposes of the present
work, linear interpolation has been applied from the tabulated database
of McCoy-s book. The developed computational method gives
satisfactory agreement with published data of verified experiments and
computational codes on atmospheric projectile trajectory analysis for
various initial firing flight conditions.
Abstract: In this study the effect of incorporation of recycled
glass-fibre reinforced polymer (GFRP) waste materials, obtained by
means of milling processes, on mechanical behaviour of polyester
polymer mortars was assessed. For this purpose, different contents of
recycled GFRP waste powder and fibres, with distinct size gradings,
were incorporated into polyester based mortars as sand aggregates
and filler replacements. Flexural and compressive loading capacities
were evaluated and found better than unmodified polymer mortars.
GFRP modified polyester based mortars also show a less brittle
behaviour, with retention of some loading capacity after peak load.
Obtained results highlight the high potential of recycled GFRP waste
materials as efficient and sustainable reinforcement and admixture for
polymer concrete and mortars composites, constituting an emergent
waste management solution.
Abstract: Multicarrier code-division multiple-access is one of the
effective techniques to gain its multiple access capability, robustness
against fading, and to mitigate the ISI. In this paper, we propose an
improved mulcarrier CDMA system with adaptive subchannel
allocation. We analyzed the performance of our proposed system in
frequency selective fading environment with narrowband interference
existing and compared it with that of parallel transmission over many
subchannels (namely, conventional MC-CDMA scheme) and
DS-CDMA system. Simulation results show that adaptive subchannel
allocation scheme, when used in conventional multicarrier CDMA
system, the performance will be greatly improved.
Abstract: In the planning point of view, it is essential to have
mode choice, due to the massive amount of incurred in transportation
systems. The intercity travellers in Libya have distinct features, as
against travellers from other countries, which includes cultural and
socioeconomic factors. Consequently, the goal of this study is to
recognize the behavior of intercity travel using disaggregate models,
for projecting the demand of nation-level intercity travel in Libya.
Multinomial Logit Model for all the intercity trips has been
formulated to examine the national-level intercity transportation in
Libya. The Multinomial logit model was calibrated using nationwide
revealed preferences (RP) and stated preferences (SP) survey. The
model was developed for deference purpose of intercity trips (work,
social and recreational). The variables of the model have been
predicted based on maximum likelihood method. The data needed for
model development were obtained from all major intercity corridors
in Libya. The final sample size consisted of 1300 interviews. About
two-thirds of these data were used for model calibration, and the
remaining parts were used for model validation. This study, which is
the first of its kind in Libya, investigates the intercity traveler’s
mode-choice behavior. The intercity travel mode-choice model was
successfully calibrated and validated. The outcomes indicate that, the
overall model is effective and yields higher precision of estimation.
The proposed model is beneficial, due to the fact that, it is receptive
to a lot of variables, and can be employed to determine the impact of
modifications in the numerous characteristics on the need for various
travel modes. Estimations of the model might also be of valuable to
planners, who can estimate possibilities for various modes and
determine the impact of unique policy modifications on the need for
intercity travel.
Abstract: Sediment formation and its transport along the river course is considered as important hydraulic consideration in river engineering. Their impact on the morphology of rivers on one hand and important considerations of which in the design and construction of the hydraulic structures on the other has attracted the attention of experts in arid and semi-arid regions. Under certain conditions where the momentum energy of the flow stream reaches a specific rate, the sediment materials start to be transported with the flow. This can usually be analyzed in two different categories of suspended and bed load materials. Sedimentation phenomenon along the waterways and the conveyance of vast volume of materials into the canal networks can potentially influence water abstraction in the intake structures. This can pose a serious threat to operational sustainability and water delivery performance in the canal networks. The situation is serious where ineffective watershed management (poor vegetation cover in the water basin) is the underlying cause of soil erosion which feeds the materials into the waterways that intern would necessitate comprehensive study. The present paper aims to present an analytical investigation of the sediment process in the waterways on one hand and estimation of the sediment load transport into the lined canals using the SHARC software on the other. For this reason, the paper focuses on the comparative analysis of the hydraulic behaviors of the Sabilli main canal that feeds the pumping station with that of the Western canal in the Greater Dezful region to identify effective factors in sedimentation and ways of mitigating their impact on water abstraction in the canal systems. The method involved use of observational data available in the Dezful Dastmashoon hydrometric station along a 6 km waterway of the Sabilli main canal using the SHARC software to estimate the suspended load concentration and bed load materials. Results showed the transport of a significant volume of sediment loads from the waterways into the canal system which is assumed to have arisen from the absence of stilling basin on one hand and the gravity flow on the other has caused serious challenges. This is contrary to what occurs in the Sabilli canal, where the design feature which incorporates a settling basin just before the pumping station is the major cause of reduced sediment load transport into the canal system.Results showed that modification of the present design features by constructing a settling basin just upstream of the western intake structure can considerably reduce the entry of sediment materials into the canal system. Not only this can result in the sustainability of the hydraulic structures but can also improve operational performance of water conveyance and distribution system, all of which are the pre-requisite to secure reliable and equitable water delivery regime for the command area.
Abstract: This paper presents results obtained from the
numerical solution for the flow past an oscillating circular cylinder at
Reynolds number of 200. The frequency of oscillation was fixed to
the vortex shedding frequency from a fixed cylinder, f0, while the
amplitudes of oscillations were varied from to 1.1a, where a
represents the radius of the cylinder. The response of the flow
through the fluid forces acting on the surface of the cylinder are
investigated. The lock-on phenomenon is captured at low oscillation
amplitudes.
Abstract: Laser soldering is based on applying some soldering material (albumin) onto the approximated edges of the cut and heating the solder (and the underlying tissues) by a laser beam. Endogenous and exogenous materials such as indocyanine green (ICG) are often added to solders to enhance light absorption. Gold nanoshells are new materials which have an optical response dictated by the plasmon resonance. The wavelength at which the resonance occurs depends on the core and shell sizes, allowing nanoshells to be tailored for particular applications. The purposes of this study was use combination of ICG and different concentration of gold nanoshells for skin tissue soldering and also to examine the effect of laser soldering parameters on the properties of repaired skin. Two mixtures of albumin solder and different combinations of ICG and gold nanoshells were prepared. A full thickness incision of 2×20 mm2 was made on the surface and after addition of mixtures it was irradiated by an 810nm diode laser at different power densities. The changes of tensile strength σt due to temperature rise, number of scan (Ns), and scan velocity (Vs) were investigated. The results showed at constant laser power density (I), σt of repaired incisions increases by increasing the concentration of gold nanoshells in solder, Ns and decreasing Vs. It is therefore important to consider the tradeoff between the scan velocity and the surface temperature for achieving an optimum operating condition. In our case this corresponds to σt =1800 gr/cm2 at I~ 47 Wcm-2, T ~ 85ºC, Ns =10 and Vs=0.3mms-1.
Abstract: In this study, we investigated the effects of ginger and
L-carnitine on the reproductive performance of male rats with respect
to semen parameters, male sex hormones and the testicular
antioxidant system. A total of sixty mature male albino rats were
divided into four groups of fifteen rats. The control group received
saline, whereas the other three groups received ginger (100 mg kg-1 d-
1.), L-carnitine (150 mg kg-1 d-1.) or a combination of both ginger
(100 mg kg-1 d-1.) and L-carnitine (150 mg kg-1 d-1.) via a stomach
tube daily for one month. At the end of the treatment period, the rats
were sacrificed, and their sperm characteristics (count, motility and
viability), antioxidant enzyme factors levels (reduced glutathione,
catalase, superoxide dismutase and total antioxidant capacity) and sex
hormone levels (testosterone, Follicle stimulating hormone(FSH) and
luteinizing hormone (LH) were analysed. Our results showed that the
three experimental treatments improved sperm parameters,
antioxidant enzyme activity and testosterone hormone levels; the
most pronounced positive effects were observed in the group that
received a combination of both ginger and L-carnitine. Therefore, the
administration of a combination of ginger and L-carnitine may be
beneficial for improving male sexual performance.