Abstract: Equipment miniaturisation offers several opportunities such as an increased surface-to-volume ratio and higher heat transfer coefficients. However, moving towards small-diameter channels demands extra attention to fouling, reliability and stable operation of the system. The present investigation explores possibilities to enhance the stability of the once-through micro evaporator by reducing its flow boiling induced pressure fluctuations. Experimental comparison shows that the measured reduction factor approaches a theoretically derived value. Pressure fluctuations are reduced by a factor of ten in the solid conical channel and a factor of 15 in the porous conical channel. This presumably leads to less backflow and therefore to a better flow control.
Abstract: Inconel718 has been widely used as a super alloy in aerospace application due to the high strength at elevated temperatures, satisfactory oxidation resistance and heat corrosion resistance. In this study, the Inconel718 has been fabricated using high technology of Metal Injection Molding (MIM) process due to the cost effective technique for producing small, complex and precision parts in high volume compared with conventional method through machining. Through MIM, the binder system is one of the most important criteria in order to successfully fabricate the Inconel718. Even though, the binder system is a temporary, but failure in the selection and removal of the binder system will affect on the final properties of the sintered parts. Therefore, the binder system based on palm oil derivative which is palm stearin has been formulated and developed to replace the conventional binder system. The rheological studies of the mixture between the powder and binders system have been determined properly in order to be successful during injection into injection molding machine. After molding, the binder holds the particles in place. The binder system has to be removed completely through debinding step. During debinding step, solvent debinding and thermal pyrolysis has been used to remove completely of the binder system. The debound part is then sintered to give the required physical and mechanical properties. The results show that the properties of the final sintered parts fulfill the Standard Metal Powder Industries Federation (MPIF) 35 for MIM parts.
Abstract: The study of the stress distribution on a hollow
cylindrical fiber placed in a composite material is considered in this
work and an analytical solution for this stress distribution has been
constructed. Finally some parameters such as fiber-s thickness and
fiber-s length are considered and their effects on the distribution of
stress have been investigated. For finding the governing relations,
continuity equations for the axisymmetric problem in cylindrical
coordinate (r,o,z) are considered. Then by assuming some conditions
and solving the governing equations and applying the boundary
conditions, an equation relates the stress applied to the representative
volume element with the stress distribution on the fiber has been
found.
Abstract: Synthetic juice clarification was done through spiral
wound ultrafiltration (UF) membrane module. Synthetic juice was
clarified at two different operating conditions, such as, with and
without permeates recycle at turbulent flow regime. The performance
of spiral wound ultrafiltration membrane was analyzed during
clarification of synthetic juice. Synthetic juice was the mixture of
deionized water, sucrose and pectin molecule. The operating
conditions are: feed flowrate of 10 lpm, pressure drop of 413.7 kPa
and Reynolds no of 5000. Permeate sample was analyzed in terms of
volume reduction factor (VRF), viscosity (Pa.s), ⁰Brix, TDS (mg/l),
electrical conductivity (μS) and turbidity (NTU). It was observe that
the permeate flux declined with operating time for both conditions of
with and without permeate recycle due to increase of concentration
polarization and increase of gel layer on membrane surface. For
without permeate recycle, the membrane fouling rate was faster
compared to with permeate recycle. For without permeate recycle,
the VRF rose up to 5 and for with recycle permeate the VRF is 1.9.
The VRF is higher due to adsorption of solute (pectin) molecule on
membrane surface and resulting permeateflux declined with VRF.
With permeate recycle, quality was within acceptable limit. Fouled
membrane was cleaned by applying different processes (e.g.,
deionized water, SDS and EDTA solution). Membrane cleaning was
analyzed in terms of permeability recovery.
Abstract: In the recent years, functionally gradient materials (FGMs) have gained considerable attention in the high temperature environment applications. In this paper, free vibration of thin functionally graded cylindrical shell with hole composed of stainless steel and zirconia is studied. The mechanical properties vary smoothly and continuously from one surface to the other according to a volume fraction power-law distribution. The Influence of shell geometrical parameters, variations of volume fractions and boundary conditions on natural frequency is considered. The equations of motion are based on strains-displacement relations from Love-s shell theory and Rayleigh method. The results have been obtained for natural frequencies of cylindrical shell with holes for different shape, number and location in this paper.
Abstract: The objective of the present work is to conduct
investigations leading to a more complete explanation of single phase
natural convective heat transfer in an enclosure with fin utilizing
nano fluids. The nano fluid used, which is composed of Aluminum
oxide nano particles in suspension of Ethylene glycol, is provided at
various volume fractions. The study is carried out numerically for a
range of Rayleigh numbers, fin heights and aspect ratio. The flow and
temperature distributions are taken to be two-dimensional. Regions
with the same velocity and temperature distributions are identified as
symmetry of sections. One half of such a rectangular region is chosen
as the computational domain taking into account the symmetry about
the fin. Transport equations are modeled by a stream functionvorticity
formulation and are solved numerically by finite-difference
schemes. Comparisons with previously published works on the basis
of special cases are done. Results are presented in the form of
streamline, vector and isotherm plots as well as the variation of local
Nusselt number along the fin under different conditions.
Abstract: Internet is largely composed of textual contents and a
huge volume of digital contents gets floated over the Internet daily.
The ease of information sharing and re-production has made it
difficult to preserve author-s copyright. Digital watermarking came
up as a solution for copyright protection of plain text problem after
1993. In this paper, we propose a zero text watermarking algorithm
based on occurrence frequency of non-vowel ASCII characters and
words for copyright protection of plain text. The embedding
algorithm makes use of frequency non-vowel ASCII characters and
words to generate a specialized author key. The extraction algorithm
uses this key to extract watermark, hence identify the original
copyright owner. Experimental results illustrate the effectiveness of
the proposed algorithm on text encountering meaning preserving
attacks performed by five independent attackers.
Abstract: The electrokinetic flow resistance (electroviscous
effect) is predicted for steady state, pressure-driven liquid flow at
low Reynolds number in a microfluidic contraction of rectangular
cross-section. Calculations of the three dimensional flow are
performed in parallel using a finite volume numerical method. The
channel walls are assumed to carry a uniform charge density and the
liquid is taken to be a symmetric 1:1 electrolyte. Predictions are
presented for a single set of flow and electrokinetic parameters. It is
shown that the magnitude of the streaming potential gradient and the
charge density of counter-ions in the liquid is greater than that in
corresponding two-dimensional slit-like contraction geometry. The
apparent viscosity is found to be very close to the value for a
rectangular channel of uniform cross-section at the chosen Reynolds
number (Re = 0.1). It is speculated that the apparent viscosity for the
contraction geometry will increase as the Reynolds number is
reduced.
Abstract: Microbial oil was produced by soil isolated
oleaginous yeast YU5/2 in flask-batch fermentation. The yeast was
identified by molecular genetics technique based on sequence
analysis of the variable D1/D2 domain of the large subunit (26S)
ribosomal DNA and it was identified as Torulaspora globosa. T.
globosa YU5/2 supported maximum values of 0.520 g/L/d, 0.472 g
lipid/g cells, 4.16 g/L, and 0.156 g/L/d for volumetric lipid
production rate, and specific yield of lipid, lipid concentration, and
specific rate of lipid production respectively, when culture was
performed in nitrogen-limiting medium supplemented with 80g/L
glucose. Among the carbon sources tested, maximum cell yield
coefficient (YX/S, g/L), maximum specific yield of lipid (YP/X, g
lipid/g cells) and volumetric lipid production rate (QP, g/L/d) were
found of 0.728, 0.237, and 0.619, respectively, using sweet potato
tubers hydrolysates as carbon source.
Abstract: Predictions of flow and heat transfer characteristics and shape optimization in internally finned circular tubes have been performed on three-dimensional periodically fully developed turbulent flow and thermal fields. For a trapezoidal fin profile, the effects of fin height h, upper fin widths d1, lower fin widths d2, and helix angle of fin ? on transport phenomena are investigated for the condition of fin number of N = 30. The CFD and mathematical optimization technique are coupled in order to optimize the shape of internally finned tube. The optimal solutions of the design variables (i.e., upper and lower fin widths, fin height and helix angle) are numerically obtained by minimizing the pressure loss and maximizing the heat transfer rate, simultaneously, for the limiting conditions of d1 = 0.5~1.5 mm, d2 = 0.5~1.5 mm, h= 0.5~1.5mm, ? = 10~30 degrees. The fully developed flow and thermal fields are predicted using the finite volume method and the optimization is carried out by means of the multi-objective genetic algorithm that is widely used in the constrained nonlinear optimization problem.
Abstract: Recently, Northeast Asia has become one of the three
largest trade areas, covering approximately 30% of the total trade
volume of the world. However, the distribution facilities are saturated
due to the increase in the transportation volume within the area and
with the European countries. In order to accommodate the increase of
the transportation volume, the transportation networking with the
major countries in Northeast Asia and Europe is absolutely necessary.
The Eurasian Logistics Network will develop into an international
passenger transportation network covering the Northeast Asian region
and an international freight transportation network connecting across
Eurasia Continent. This paper surveys the changes and trend of the
distribution network in the Eurasian Region according to the political,
economic and environmental changes of the region, analyses the
distribution network according to the changes in the transportation
policies of the related countries, and provides the direction of the
development of composite transportation on the basis of the present
conditions of transportation means. The transportation means optimal
for the efficiency of transportation system are suggested to be train
ferries, sea & rail or sea & rail & sea. It is suggested to develop
diversified composite transportation means and routes within the
boundary of international cooperation system.
Abstract: A new dual-fluid concept was studied that could eventually find application for cold-gas propulsion for small space satellites or other constant flow applications. In basic form, the concept uses two different refrigerant working fluids, each having a different saturation vapor pressure. The higher vapor pressure refrigerant remains in the saturation phase and is used to pressurize the lower saturation vapor pressure fluid (the propellant) which remains in the compressed liquid phase. A demonstration thruster concept based on this principle was designed and built to study its operating characteristics. An automotive-type electronic fuel injector was used to meter and deliver the propellant. Ejected propellant mass and momentum were measured for several combinations of refrigerants and hydrocarbon fluids. The thruster has the advantage of delivering relatively large total impulse at low tank pressure within a small volume.
Abstract: The volume of XML data exchange is explosively increasing, and the need for efficient mechanisms of XML data management is vital. Many XML storage models have been proposed for storing XML DTD-independent documents in relational database systems. Benchmarking is the best way to highlight pros and cons of different approaches. In this study, we use a common benchmarking scheme, known as XMark to compare the most cited and newly proposed DTD-independent methods in terms of logical reads, physical I/O, CPU time and duration. We show the effect of Label Path, extracting values and storing in another table and type of join needed for each method's query answering.
Abstract: Horseradish (Armoracia rusticana) is a perennial herb belonging to the Brassicaceae family and contains biologically active substances. The aim of the current research was to determine best method for extraction of phenolic compounds from horseradish roots showing high antiradical activity. Three genotypes (No. 105; No. 106 and variety ‘Turku’) of horseradish roots were extracted with eight different solvents: n-hexane, ethyl acetate, diethyl ether, 2-propanol, acetone, ethanol (95%), ethanol / water / acetic acid (80/20/1 v/v/v) and ethanol / water (80/20 by volume) using two extraction methods (conventional and Soxhlet). As the best solvents ethanol and ethanol / water solutions can be chosen. Although in Soxhlet extracts TPC was higher, scavenging activity of DPPH˙ radicals did not increase. It can be concluded that using Soxhlet extraction method more compounds that are not effective antioxidants.
Abstract: In this paper, we analyzed the pattern of urban spatial structure of Siheung City that had been divided into two parts and presented alternative plans in order to get rid of these phenomena. Concerning patterns of urban spatial structure, we examined it through means of analyzing status of land use, population density and distribution of residence, status of distribution of main facilities, medical facilities, status of distribution of cultural facilities, distribution of land prices and traffic volume trends. The results of study revealed that status of facilities distribution and distribution of land prices, etc. were bisected by the surrounding area of former municipal office and the district of Sihwa, which were both regarded as one apex of the city divide, forming a duo-centric city. In order to get rid of this problem concerned with urban spatial structure that has been bisected, it is required that measures in order to expand facilities in Siheung City should be taken.
Abstract: Dual phase steels (DPS)s have a microstructure
consisting of a hard second phase called Martensite in the soft Ferrite
matrix. In recent years, there has been interest in dual-phase steels,
because the application of these materials has made significant usage;
particularly in the automotive sector Composite microstructure of
(DPS)s exhibit interesting characteristic mechanical properties such
as continuous yielding, low yield stress to tensile strength
ratios(YS/UTS), and relatively high formability; which offer
advantages compared with conventional high strength low alloy
steels(HSLAS). The research dealt with the characterization of
damage in (DPS)s. In this study by review the mechanisms of failure
due to volume fraction of martensite second phase; a new method is
introduced to identifying the mechanisms of failure in the various
phases of these types of steels. In this method the acoustic emission
(AE) technique was used to detect damage progression. These failure
mechanisms consist of Ferrite-Martensite interface decohesion and/or
martensite phase fracture. For this aim, dual phase steels with
different volume fraction of martensite second phase has provided by
various heat treatment methods on a low carbon steel (0.1% C), and
then AE monitoring is used during tensile test of these DPSs. From
AE measurements and an energy ratio curve elaborated from the
value of AE energy (it was obtained as the ratio between the strain
energy to the acoustic energy), that allows detecting important
events, corresponding to the sudden drops. These AE signals events
associated with various failure mechanisms are classified for ferrite
and (DPS)s with various amount of Vm and different martensite
morphology. It is found that AE energy increase with increasing Vm.
This increasing of AE energy is because of more contribution of
martensite fracture in the failure of samples with higher Vm. Final
results show a good relationship between the AE signals and the
mechanisms of failure.
Abstract: This work relates the development of an optical fiber
(OF) sensor for the detection and quantification of single walled
carbon nanotubes in aqueous solutions. The developed OF displays a
compact design, it requires less expensive materials and equipment
as well as low volume of sample (0.2 mL). This methodology was
also validated by the comparison of its analytical performance with
that of a standard methodology based on ultraviolet-visible
spectroscopy. The developed OF sensor follows the general SDS
calibration proposed for OF sensors as a more suitable calibration
fitting compared with classical calibrations.
Abstract: Experiments were carried out to evaluate the
influence of the addition of hydrogen to the inlet air on the
performance of a single cylinder direct injection diesel engine.
Hydrogen was injected in the inlet manifold. The addition of
hydrogen was done on energy replacement basis. It was found that
the addition of hydrogen improves the combustion process due to
superior combustion characteristics of hydrogen in comparison to
conventional diesel fuels. It was also found that 10% energy
replacement improves the engine thermal efficiency by about 40%
and reduces the sfc by about 35% however the volumetric efficiency
was reduced by about 35%.
Abstract: In this study, some physical and mechanical properties
of jujube fruits, were measured and compared at constant moisture
content of 15.5% w.b. The results showed that the mean length, width
and thickness of jujube fruits were 18.88, 16.79 and 15.9 mm,
respectively. The mean projected areas of jujube perpendicular to
length, width, and thickness were 147.01, 224.08 and 274.60 mm2,
respectively. The mean mass and volume were 1.51 g and 2672.80
mm3, respectively. The arithmetic mean diameter, geometric mean
diameter and equivalent diameter varied from 14.53 to 20 mm, 14.5
to 19.94 mm, and 14.52 to 19.97 mm, respectively. The sphericity,
aspect ratio and surface area of jujube fruits were 0.91, 0.89 and
926.28 mm2, respectively. Whole fruit density, bulk density and
porosity of jujube fruits were measured and found to be 1.52 g/cm3,
0.3 g/cm3 and 79.3%, respectively. The angle of repose of jujube fruit
was 14.66° (±0.58°). The static coefficient of friction on galvanized
iron steel was higher than that on plywood and lower than that on
glass surface. The values of rupture force, deformation, hardness and
energy absorbed were found to be between 11.13-19.91N, 2.53-
4.82mm, 3.06-5.81N mm and 20.13-39.08 N/mm, respectively.
Abstract: The paper provides a numerical investigation of the
entropy generation analysis due to natural convection in an inclined
square porous cavity. The coupled equations of mass, momentum,
energy and species conservation are solved using the Control Volume
Finite-Element Method. Effect of medium permeability and
inclination angle on entropy generation is analysed. It was found that
according to the Darcy number and the porous thermal Raleigh
number values, the entropy generation could be mainly due to heat
transfer or to fluid friction irreversibility and that entropy generation
reaches extremum values for specific inclination angles.