Abstract: This paper investigates the influence of various
parameters on the behaviour of water droplets on polymeric surfaces
under high electric fields. An inclined plane test was carried out to
understand the droplet behaviour in strong electric field. Parameters
such as water droplet conductivity, droplet volume, polymeric
surface roughness and droplet positioning with respect to the
electrodes were studied. The flashover voltage is affected by all
aforementioned parameters. The droplet positioning is in some cases
more vital than the droplet volume. Surface damages were analysed
using Scanning Electron Microscopy (SEM) studies and by Energy
dispersive X-ray Analysis (EDAX). It is observes that magnitude of
discharge have direct influence on amount of surface da
Abstract: Most of ignition delay correlations studies have been
developed in a constant volume bombs which cannot capture the
dynamic variation in pressure and temperature during the ignition
delay as in real engines. Watson, Assanis et. al. and Hardenberg
and Hase correlations have been developed based on experimental
data of diesel engines. However, they showed limited predictive
ability of ignition delay when compared to experimental results. The
objective of the study was to investigate the dependency of ignition
delay time on engine brake power. An experimental investigation of
the effect of automotive diesel and water diesel emulsion fuels on
ignition delay under steady state conditions of a direct injection diesel
engine was conducted. A four cylinder, direct injection naturally
aspirated diesel engine was used in this experiment over a wide range
of engine speeds and two engine loads. The ignition delay
experimental data were compared with predictions of Assanis et. al.
and Watson ignition delay correlations. The results of the
experimental investigation were then used to develop a new ignition
delay correlation. The newly developed ignition delay correlation has
shown a better agreement with the experimental data than Assanis et.
al. and Watson when using automotive diesel and water diesel
emulsion fuels especially at low to medium engine speeds at both
loads. In addition, the second derivative of cylinder pressure which is
the most widely used method in determining the start of combustion
was investigated.
Abstract: Increasing growth of information volume in the
internet causes an increasing need to develop new (semi)automatic
methods for retrieval of documents and ranking them according to
their relevance to the user query. In this paper, after a brief review
on ranking models, a new ontology based approach for ranking
HTML documents is proposed and evaluated in various
circumstances. Our approach is a combination of conceptual,
statistical and linguistic methods. This combination reserves the
precision of ranking without loosing the speed. Our approach
exploits natural language processing techniques for extracting
phrases and stemming words. Then an ontology based conceptual
method will be used to annotate documents and expand the query.
To expand a query the spread activation algorithm is improved so
that the expansion can be done in various aspects. The annotated
documents and the expanded query will be processed to compute
the relevance degree exploiting statistical methods. The outstanding
features of our approach are (1) combining conceptual, statistical
and linguistic features of documents, (2) expanding the query with
its related concepts before comparing to documents, (3) extracting
and using both words and phrases to compute relevance degree, (4)
improving the spread activation algorithm to do the expansion based
on weighted combination of different conceptual relationships and
(5) allowing variable document vector dimensions. A ranking
system called ORank is developed to implement and test the
proposed model. The test results will be included at the end of the
paper.
Abstract: Since polymerase chain reaction (PCR) has been
invented, it has emerged as a powerful tool in genetic analysis. The
PCR products are closely linked with thermal cycles. Therefore, to
reduce the reaction time and make temperature distribution uniform in
the reaction chamber, a novel oscillatory thermal cycler is designed.
The sample is placed in a fixed chamber, and three constant isothermal
zones are established and lined in the system. The sample is oscillated
and contacted with three different isothermal zones to complete
thermal cycles. This study presents the design of the geometric
characteristics of the chamber. The commercial software
CFD-ACE+TM is utilized to investigate the influences of various
materials, heating times, chamber volumes, and moving speed of the
chamber on the temperature distributions inside the chamber. The
chamber moves at a specific velocity and the boundary conditions
with time variations are related to the moving speed. Whereas the
chamber moves, the boundary is specified at the conditions of the
convection or the uniform temperature. The user subroutines compiled
by the FORTRAN language are used to make the numerical results
realistically. Results show that the reaction chamber with a rectangular
prism is heated on six faces; the effects of various moving speeds of
the chamber on the temperature distributions are examined. Regarding
to the temperature profiles and the standard deviation of the
temperature at the Y-cut cross section, the non-uniform temperature
inside chamber is found as the moving speed is larger than 0.01 m/s.
By reducing the heating faces to four, the standard deviation of the
temperature of the reaction chamber is under 1.4×10-3K with the range
of velocities between 0.0001 m/s and 1 m/s. The nature convective
boundary conditions are set at all boundaries while the chamber moves
between two heaters, the effects of various moving velocities of the
chamber on the temperature distributions are negligible at the assigned
time duration.
Abstract: Presently and in line with the United Nations (EPA),
human thinking system has shifted towards clean fuels so as to
maintain a cleaner environment and to save our planet earth.
One of the most successful studies in order to achieve new
energies includes the use of animal wastes and their organic residues,
and the result of these researches has been represented in the form of
very simple and cheap methods called biogas technology. Biogas
technology has developed a lot in the recent decades; its reason is the
high cost of fossil fuels and the greater attention of countries to the
environmental pollutions due to the consumption of this kind of
fuels.
IRAN is ready for the optimized application of renewable
energies, having much enriched resources of this kind of energies; so
a special place could be considered for it when making programs.
The purpose of biogas technology is the recovery of energy and
finally the protection of the environment, which is much appropriate
for the third world farmers with respect to their technical abilities and
economic potentials. Studies show that the production and
consumption of biogas is appropriate and economic in IRAN,
because of the high amount of waste in the agriculture sector, the
significant amount of animal and human excrement production, the
great volume of garbage produced and the most important the
specific social, climatic and agricultural conditions in IRAN, in order
to proceed towards the reduction of pollution due to the use of fossil
fuels.
Abstract: In this study acoustic emission (AE) signals obtained during deformation and fracture of two types of ferrite-martensite dual phase steels (DPS) specimens have been analyzed in frequency domain. For this reason two low carbon steels with various amounts of carbon were chosen, and intercritically heat treated. In the introduced method, identifying the mechanisms of failure in the various phases of DPS is done. For this aim, AE monitoring has been used during tensile test of several DPS with various volume fraction of the martensite (VM) and attempted to relate the AE signals and failure mechanisms in these steels. Different signals, which referred to 2-3 micro-mechanisms of failure due to amount of carbon and also VM have been seen. By Fast Fourier Transformation (FFT) of signals in distinct locations, an excellent relationship between peak frequencies in these areas and micro-mechanisms of failure were seen. The results were verified by microscopic observations (SEM).
Abstract: Study of the vibration cylindrical shells made of
a functionally gradient material (FGM) composed of stainless
steel and nickel is important. Material properties are graded in
the thickness direction of the shell according to volume
fraction power law distribution. The objective is to study the
natural frequencies, the influence of constituent volume
fractions and the effects of boundary conditions on the natural
frequencies of the FG cylindrical shell. The study is carried
out using third order shear deformation shell theory. The
governing equations of motion of FG cylindrical shells are
derived based on shear deformation theory. Results are
presented on the frequency characteristics, influence of
constituent volume fractions and the effects of clampedclamped
boundary conditions.
Abstract: This paper aims to fabricated high quality anodic
aluminum oxide (AAO) film by anodization method. AAO pore size,
pore density, and film thickness can be controlled in 10~500 nm,
108~1011 pore．cm-2, and 1~100 μm. AAO volume and surface area can
be computed based on structural parameters such as thickness, pore
size, pore density, and sample size. Base on the thetorical calculation,
AAO has 100 μm thickness with 15 nm, 60 nm, and 500 nm pore
diameters AAO surface areas are 1225.2 cm2, 3204.4 cm2, and 549.7
cm2, respectively. The large unit surface area which is useful for
adsorption application. When AAO adsorbed pH indictor of
bromphenol blue presented a sensitive pH detection of solution
change. This testing method can further be used for the precise
measurement of biotechnology, convenience measurement of
industrial engineering.
Abstract: A business case is a proposal for an investment
initiative to satisfy business and functional requirements. The
business case provides the foundation for tactical decision making
and technology risk management. It helps to clarify how the
organization will use its resources in the best way by providing
justification for investment of resources. This paper describes how
simulation was used for business case benefits and return on
investment for the procurement of 8 production machines. With
investment costs of about 4.7 million dollars and annual operating
costs of about 1.3 million, we needed to determine if the machines
would provide enough cost savings and cost avoidance. We
constructed a model of the existing factory environment consisting of
8 machines and subsequently, we conducted average day simulations
with light and heavy volumes to facilitate planning decisions
required to be documented and substantiated in the business case.
Abstract: In this study, the kinetic of biogas production was studied by performing a series laboratory experiment using rumen fluid of animal ruminant as inoculums. Cattle manure as substrate was inoculated by rumen fluid to the anaerobic biodigester. Laboratory experiments using 400 ml biodigester were performed in batch operation mode. Given 100 grams of fresh cattle manure was fed to each biodigester and mixed with rumen fluid by manure : rumen weight ratio of 1:1 (MR11). The operating temperatures were varied at room temperature and 38.5 oC. The cumulative volume of biogas produced was used to measure the biodigester performance. The research showed that the rumen fluid inoculated to biodigester gave significant effect to biogas production (P
Abstract: Absorptive characteristics of polyaniline synthesized
in mixture of water and acetonitrile in 50/50 volume ratio was
studied. Synthesized polyaniline in powder shape is used as an
adsorbent to remove toxic hexavalent chromium from aqueous
solutions. Experiments were conducted in batch mode with different
variables such as agitation time, solution pH and initial concentration
of hexavalent chromium. Removal mechanism is the combination of
surface adsorption and reduction. The equilibrium time for removal
of Cr(T) and Cr(VI) was about 2 and 10 minutes respectively. The
optimum pH for total chromium removal occurred at pH 7 and
maximum hexavalent chromium removal took place under acidic
condition at pH 3. Investigating the isothermal characteristics showed
that the equilibrium adsorption data fitted both Freundlich-s and
Langmuir-s isotherms. The maximum adsorption of chromium was
calculated 36.1 mg/g for polyaniline
Abstract: This work presents the experimental results obtained
at a pilot plant which works with a slow, wet and catalytic pyrolysis
process of dry fowl manure. This kind of process mainly consists in
the cracking of the organic matrix and in the following reaction of
carbon with water, which is either already contained in the organic
feed or added, to produce carbon monoxide and hydrogen. Reactions
are conducted in a rotating reactor maintained at a temperature of
500°C; the required amount of water is about 30% of the dry organic
feed. This operation yields a gas containing about 59% (on a volume
basis) of hydrogen, 17% of carbon monoxide and other products such
as light hydrocarbons (methane, ethane, propane) and carbon
monoxide in lesser amounts. The gas coming from the reactor can be
used to produce not only electricity, through internal combustion
engines, but also heat, through direct combustion in industrial
boilers. Furthermore, as the produced gas is devoid of both solid
particles and pollutant species (such as dioxins and furans), the
process (in this case applied to fowl manure) can be considered as an
optimal way for the disposal and the contemporary energetic
valorization of organic materials, in such a way that is not damaging
to the environment.
Abstract: The Yasuj city stream named the Beshar supply
water for different usages such as aquaculture farms , drinking,
agricultural and industrial usages. Fish processing plants
,Agricultural farms, waste water of industrial zones and hospitals
waste water which they are generate by human activity produce a
considerable volume of effluent and when they are released in to the
stream they can effect on the water quality and down stream aquatic
systems. This study was conducted to evaluate the effects of outflow
effluent from different human activity and point and non point
pollution sources on the water quality and health of the Beshar
river next to Yasuj. Yasuj is the biggest and most important city in
the Kohkiloye and Boyerahmad province . The Beshar River is one
of the most important aquatic ecosystems in the upstream of the
Karun watershed in south of Iran which is affected by point and non
point pollutant sources . This study was done in order to evaluate the
effects of human activities on the water quality and health of the
Beshar river. This river is approximately 190 km in length and
situated at the geographical positions of 51° 20' to 51° 48' E and 30°
18' to 30° 52' N it is one of the most important aquatic ecosystems of
Kohkiloye and Boyerahmad province in south-west Iran. In this
research project, five study stations were selected to examine water
pollution in the Beshar River systems. Human activity is now one of
the most important factors affecting on hydrology and water quality
of the Beshar river. Humans use large amounts of resources to sustain
various standards of living, although measures of sustainability are
highly variable depending on how sustainability is defined. The
Beshar river ecosystems are particularly sensitive and vulnerable to
human activities. The water samples were analyzed, then some
important water quality parameters such as pH, dissolve oxygen
(DO), Biochemical Oxygen Demand (BOD5), Chemical Oxygen
Demand (COD), Total Suspended Solids (TDS),Turbidity,
Temperature, Nitrates (NO3) and Phosphates (PO4) were estimated
at the two stations. The results show a downward trend in the water
quality at the down stream of the city. The amounts of
BOD5,COD,TSS,T,Turbidity, NO3 and PO4 in the down stream
stations were considerably more than the station 1. By contrast the
amounts of DO in the down stream stations were less than to the
station 1. However when effluent discharge consequence of human
activities are released into the Beshar river near the city, the quality
of river are decreases and the environmental problems of the river
during the next years are predicted to rise.
Abstract: Shadows add great amount of realism to a scene and
many algorithms exists to generate shadows. Recently, Shadow
volumes (SVs) have made great achievements to place a valuable
position in the gaming industries. Looking at this, we concentrate on
simple but valuable initial partial steps for further optimization in SV
generation, i.e.; model simplification and silhouette edge detection
and tracking. Shadow volumes (SVs) usually takes time in generating
boundary silhouettes of the object and if the object is complex then
the generation of edges become much harder and slower in process.
The challenge gets stiffer when real time shadow generation and
rendering is demanded. We investigated a way to use the real time
silhouette edge detection method, which takes the advantage of
spatial and temporal coherence, and exploit the level-of-details
(LOD) technique for reducing silhouette edges of the model to use
the simplified version of the model for shadow generation speeding
up the running time. These steps highly reduce the execution time of
shadow volume generations in real-time and are easily flexible to any
of the recently proposed SV techniques. Our main focus is to exploit
the LOD and silhouette edge detection technique, adopting them to
further enhance the shadow volume generations for real time
rendering.
Abstract: Cashew nut shells were converted into activated carbon powders using KOH activation plus CO2 gasification at 1027 K. The increase both of impregnation ratio and activation time, there was swiftly the development of mesoporous structure with increasing of mesopore volume ratio from 20-28% and 27-45% for activated carbon with ratio of KOH per char equal to 1 and 4, respectively. Activated carbon derived from KOH/char ratio equal to 1 and CO2 gasification time from 20 to 150 minutes were exhibited the BET surface area increasing from 222 to 627 m2.g-1. And those were derived from KOH/char ratio of 4 with activation time from 20 to 150 minutes exhibited high BET surface area from 682 to 1026 m2.g-1. The adsorption of Lead(II) and Cadmium(II) ion was investigated. This adsorbent exhibited excellent adsorption for Lead(II) and Cadmium(II) ion. Maximum adsorption presented at 99.61% at pH 6.5 and 98.87% at optimum conditions. The experimental data was calculated from Freundlich isotherm and Langmuir isotherm model. The maximum capacity of Pb2+ and Cd2+ ions was found to be 28.90 m2.g-1 and 14.29 m2.g-1, respectively.
Abstract: Plants are rich sources of bioactive compounds. In this study the photochemical screening of hexane, ethanolic and aqueous extracts of roots and latex of jojoba (Simmondsia chinensis) plant revealed the presence of saponins, tannins, alkaloids, steroids and glycosides. Ethanolic extract was found to be richer in these metabolites than hexane, aqueous extracts and latex. The extracts and latex displayed effective antimicrobial activity against Salmonella typhimurium, Bacillus cereus, Clostridium perfringens, Staphylococcus aureus, Escherichia coli, Candida albicans and Aspergillus flavus. The increase in volume of the extracts and latex caused more activity, as shown by zones of inhibition. Candida albicans growth was inhibited only by hexane extract. Jojoba latex was not effective against Candida albicans at 0.1 and 0.5 ml extracts concentration but showed 5mm zone of inhibition at (1.0 ml). Lower volume (0.1ml) of latex encouraged Aspergillus flavus growth, while at (1.00 ml) reduced its mycelial growth. Thus, jojoba root extracts and latex can be of potential natural antimicrobial agents.
Abstract: The first and basic cause of the failure of concrete is repeated freezing (thawing) of moisture contained in the pores, microcracks, and cavities of the concrete. On transition to ice, water existing in the free state in cracks increases in volume, expanding the recess in which freezing occurs. A reduction in strength below the initial value is to be expected and further cycle of freezing and thawing have a further marked effect. By using some experimental parameters like nuclear magnetic resonance variation (NMR), enthalpy-temperature (or heat capacity) variation, we can resolve between the various water states and their effect on concrete properties during cooling through the freezing transition temperature range. The main objective of this paper is to describe the principal type of water responsible for the reduction in strength and structural damage (frost damage) of concrete following repeated freeze –thaw cycles. Some experimental work was carried out at the institute of cryogenics to determine what happens to water in concrete during the freezing transition.
Abstract: Impact is one of very important subjects which always have been considered in mechanical science. Nature of impact is such that which makes its control a hard task. Therefore it is required to present the transfer of impact to other vulnerable part of a structure, when it is necessary, one of the best method of absorbing energy of impact, is by using Thin-walled tubes these tubes collapses under impact and with absorption of energy, it prevents the damage to other parts.Purpose of recent study is to survey the deformation and energy absorption of tubes with different type of cross section (rectangular or square) and with similar volumes, height, mean cross section thickness, and material under loading with different speeds. Lateral loading of tubes are quasi-static type and beside as numerical analysis, also experimental experiences has been performed to evaluate the accuracy of the results. Results from the surveys is indicates that in a same conditions which mentioned above, samples with square cross section ,absorb more energy compare to rectangular cross section, and also by increscent in speed of loading, energy absorption would be more.
Abstract: Cement, the most widely used construction material
is very brittle and characterized by low tensile strength and strain
capacity. Macro to nano fibers are added to cement to provide
tensile strength and ductility to it. Carbon Nanotube (CNT), one of
the nanofibers, has proven to be a promising reinforcing material in
the cement composites because of its outstanding mechanical
properties and its ability to close cracks at the nano level. The
experimental investigations for CNT reinforced cement is costly,
time consuming and involves huge number of trials. Mathematical
modeling of CNT reinforced cement can be done effectively and
efficiently to arrive at the mechanical properties and to reduce the
number of trials in the experiments. Hence, an attempt is made to
numerically study the effective mechanical properties of CNT
reinforced cement numerically using Representative Volume
Element (RVE) method. The enhancement in its mechanical
properties for different percentage of CNTs is studied in detail.
Abstract: In the present work, study of the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. Material properties are graded in the thickness direction of the shell according to volume fraction power law distribution. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of boundary conditions on the natural frequencies of the FG cylindrical shell. The study is carried out using third order shear deformation shell theory. The analysis is carried out using Hamilton's principle. The governing equations of motion of FG cylindrical shells are derived based on shear deformation theory. Results are presented on the frequency characteristics, influence of constituent volume fractions and the effects of clamped-free boundary conditions