Abstract: Green and renewable energy is getting extraordinary
consideration today, because of ecological concerns made by blazing
of fossil powers. Photovoltaic and wind power generation are the
basic decisions for delivering power in this respects. Producing
power by the sun based photovoltaic systems is known to the world,
yet control makers may get confounded to pick between on-grid and
off-grid systems. In this exploration work, an endeavor is made to
compare the off-grid (stand-alone) and on-grid (grid-connected)
frameworks. The work presents relative examination, between two
distinctive PV frameworks situated at V.V.P. Engineering College,
Rajkot. The first framework is 100 kW remain solitary and the
second is 60 kW network joined. The real-time parameters compared
are; output voltage, load current, power in-flow, power output,
performance ratio, yield factor, and capacity factor. The voltage
changes and the power variances in both frameworks are given
exceptional consideration and the examination is made between the
two frameworks to judge the focal points and confinements of both
the frameworks.
Abstract: A Friction stir welding tool is a critical component to
the success of the process. The tool typically consists of a rotating
round shoulder and a threaded cylindrical pin that heats the work
piece, mostly by friction, and moves the softened alloy around it to
form the joint. In this research work, an attempt has been made to
investigate the relationship between FSW variables mainly tool
profile, rotating speed, welding speed and the mechanical properties
(tensile strength, yield strength, percentage elongation, and micro
hardness) of friction stir welded aluminum alloy 5083 joints. From
the experimental details, it can be assessed that the joint produced by
using Triflute profile tool has contribute superior mechanical and
structural properties as compared to Tapered unthreaded & Threaded
tool for 1000rpm.
Abstract: Wavelength Division Multiplexing (WDM)
technology is the most promising technology for the proper
utilization of huge raw bandwidth provided by an optical fiber. One
of the key problems in implementing the all-optical WDM network is
the packet contention. This problem can be solved by several
different techniques. In time domain approach the packet contention
can be reduced by incorporating Fiber Delay Lines (FDLs) as optical
buffer in the switch architecture. Different types of buffering
architectures are reported in literatures. In the present paper a
comparative performance analysis of three most popular FDL
architectures are presented in order to obtain the best contention
resolution performance. The analysis is further extended to consider
the effect of different fiber non-linearities on the network
performance.
Abstract: Online measurement of the product quality is a
challenging task in cement production, especially in the production of
Celitement, a novel environmentally friendly hydraulic binder. The
mineralogy and chemical composition of clinker in ordinary Portland
cement production is measured by X-ray diffraction (XRD) and
X-ray fluorescence (XRF), where only crystalline constituents can be
detected. But only a small part of the Celitement components can be
measured via XRD, because most constituents have an amorphous
structure. This paper describes the development of algorithms
suitable for an on-line monitoring of the final processing step of
Celitement based on NIR-data. For calibration intermediate products
were dried at different temperatures and ground for variable
durations. The products were analyzed using XRD and
thermogravimetric analyses together with NIR-spectroscopy to
investigate the dependency between the drying and the milling
processes on one and the NIR-signal on the other side. As a result,
different characteristic parameters have been defined. A short
overview of the Celitement process and the challenging tasks of the
online measurement and evaluation of the product quality will be
presented. Subsequently, methods for systematic development of
near-infrared calibration models and the determination of the final
calibration model will be introduced. The application of the model on
experimental data illustrates that NIR-spectroscopy allows for a quick
and sufficiently exact determination of crucial process parameters.
Abstract: In this paper, we introduce a flexible box erecting
machine (BEM) that swiftly and automatically transforms cardboard
into a three dimensional box. Recently, the parcel service and
home-shopping industries have grown rapidly, and there is an
increasing need for various box types to ship various products.
However, workers cannot fold thousands of boxes manually in a day.
As such, automatic BEMs are garnering greater attention. This study
takes equipment operation into consideration as well as mechanical
improvements in order to design a BEM that is able to outperform its
conventional counterparts. We analyzed six dispatching rules – First In
First Out (FIFO), Shortest Processing Time (SPT), Earliest Due Date
(EDD), Setup Avoidance, EDD + SPT, and EDD + Setup Avoidance –
to determine which one was most suitable for BEM operation.
Consequently, SPT and Setup Avoidance were found to be the most
critical rules, followed by EDD + Setup Avoidance, EDD + SPT,
EDD, and FIFO. This hierarchy was valid for both our conventional
BEM and our new flexible BEM from the viewpoint of processing
time. We believe that this research can contribute to flexible BEM
management, which has the potential to increase productivity and
convenience.
Abstract: Fresh concrete has one of dynamic properties known
as slump. Slump of concrete is design to compatible with placing
method. Due to hydration reaction of cement, the slump of concrete
is loss through time. Therefore, delayed concrete probably get reject
because slump is unacceptable. In order to recover the slump of
delayed concrete the second dose of superplasticizer (naphthalene
based type F) is added into the system, the slump recovery can be
done as long as the concrete is not setting. By adding superplasticizer
as solution for recover unusable slump loss concrete may affects
other concrete properties. Therefore, this paper was observed setting
times and compressive strength of concrete after being re-dose with
chemical admixture type F (superplasticizer, naphthalene based) for
slump recovery. The concrete used in this study was fly ash concrete
with fly ash replacement of 0%, 30% and 50% respectively. Concrete
mix designed for test specimen was prepared with paste content (ratio
of volume of cement to volume of void in the aggregate) of 1.2 and
1.3, water-to-binder ratio (w/b) range of 0.3 to 0.58, initial dose of
superplasticizer (SP) range from 0.5 to 1.6%. The setting times of
concrete were tested both before and after re-dosed with different
amount of second dose and time of dosing. The research was
concluded that addition of second dose of superplasticizer would
increase both initial and final setting times accordingly to dosage of
addition. As for fly ash concrete, the prolongation effect was higher
as the replacement of fly ash increase. The prolongation effect can
reach up to maximum about 4 hours. In case of compressive strength,
the re-dosed concrete has strength fluctuation within acceptable range
of ±10%.
Abstract: This paper describes the development of new class of
epoxy based rice husk filled jute reinforced composites. Rice husk
flour is added in 0%, 1%, 3%, 5% by weight. Epoxy resin and
triethylenetetramine (T.E.T.A) is used as matrix and hardener
respectively. It investigates the mechanical properties of the
composites and a comparison is done for monolithic jute composite
and the filled ones. The specimens are prepared according to the
ASTM standards and experimentation is carried out using INSTRON
8801. The result shows that with the increase of filler percentage the
tensile properties increases but compressive and flexural properties
decreases.
Abstract: This study evaluated to facilitate separation of ABS
plastics from other waste plastics by froth flotation after surface
hydrophilization of ABS with heat treatment. The mild heat treatment
at 100oC for 60s could selectively increase the hydrophilicity of the
ABS plastics surface (i.e., ABS contact angle decreased from 79o to
65.8o) among other plastics mixture. The SEM and XPS results of
plastic samples sufficiently supported the increase in hydrophilic
functional groups and decrease contact angle on ABS surface, after
heat treatment. As a result of the froth flotation (at mixing speed 150
rpm and airflow rate 0.3 L/min) after heat treatment, about 85% of
ABS was selectively separated from other heavy plastics with 100%
of purity. The effect of optimum treatment condition and detailed
mechanism onto separation efficiency in the froth floatation was also
investigated. This research is successful in giving a simple, effective,
and inexpensive method for ABS separation from waste plastics.
Abstract: Brushless DC motors (BLDC) are widely used in
industrial areas. The BLDC motors are driven either by indirect ACAC
converters or by direct AC-AC converters. Direct AC-AC
converters i.e. matrix converters are used in this paper to drive the
three phase BLDC motor and it eliminates the bulky DC link energy
storage element. A matrix converter converts the AC power supply to
an AC voltage of variable amplitude and variable frequency. A
control technique is designed to generate the switching pulses for the
three phase matrix converter. For the control of speed of the BLDC
motor a separate PI controller and Fuzzy Logic Controller (FLC) are
designed and a hysteresis current controller is also designed for the
control of motor torque. The control schemes are designed and tested
separately. The simulation results of both the schemes are compared
and contrasted in this paper. The results show that the fuzzy logic
control scheme outperforms the PI control scheme in terms of
dynamic performance of the BLDC motor. Simulation results are
validated with the experimental results.
Abstract: The research investigates the causes of unemployment
in Namibia, Nigeria and South Africa and the role of Capital
Accumulation in reducing the unemployment profile of these
economies as proposed by the post-Keynesian economics. This is
conducted through extensive review of literature on the NAIRU
models and focused on the post-Keynesian view of unemployment
within the NAIRU framework. The NAIRU (non-accelerating
inflation rate of unemployment) model has become a dominant
framework used in macroeconomic analysis of unemployment. The
study views the post-Keynesian economics arguments that capital
accumulation is a major determinant of unemployment.
Unemployment remains the fundamental socio-economic challenge
facing African economies. It has been a burden to citizens of those
economies. Namibia, Nigeria, and South Africa are great African
nations battling with high unemployment rates. The high
unemployment rate in the country led the citizens to chase away
foreigners in the country claiming that they have taken away their
jobs. The study proposes there is a strong relationship between
capital accumulation and unemployment in Namibia, Nigeria, and
South Africa, and capital accumulation is responsible for high
unemployment rates in these countries. For the economies to achieve
steady state level of employment and satisfactory level of economic
growth and development, there is need for capital accumulation to
take place. The countries in the study have been selected after a
critical research and investigations. They are selected based on the
following criteria; African economies with high unemployment rates
above 15% and have about 40% of their workforce unemployed. This
level of unemployment is the critical level of unemployment in
Africa as expressed by International Labour Organization (ILO). And
finally, the African countries experience a slow growth in their Gross
fixed capital formation. Adequate statistical measures have been
employed using a time-series analysis in the study and the results
revealed that capital accumulation is the main driver of
unemployment performance in the chosen African countries. An
increase in the accumulation of capital causes unemployment to
reduce significantly. The results of the research work will be useful
and relevant to federal governments and ministries, departments and
agencies (MDAs) of Namibia, Nigeria and South Africa to resolve
the issue of high and persistent unemployment rates in their
economies which are great burden that slows growth and
development of developing economies. Also, the result can be useful
to World Bank, African Development Bank and International Labour
Organization (ILO) in their further research and studies on how to
tackle unemployment in developing and emerging economies.
Abstract: The question of legal liability over injury arising out
of the import and the introduction of GM food emerges as a crucial
issue confronting to promote GM food and its derivatives. There is a
greater possibility of commercialized GM food from the exporting
country to enter importing country where status of approval shall not
be same. This necessitates the importance of fixing a liability
mechanism to discuss the damage, if any, occurs at the level of
transboundary movement or at the market. There was a widespread consensus to develop the Cartagena
Protocol on Biosafety and to give for a dedicated regime on liability
and redress in the form of Nagoya Kuala Lumpur Supplementary
Protocol on the Liability and Redress (‘N-KL Protocol’) at the
international context. The national legal frameworks based on this
protocol are not adequately established in the prevailing food
legislations of the developing countries. The developing economy
like India is willing to import GM food and its derivatives after the
successful commercialization of Bt Cotton in 2002. As a party to the
N-KL Protocol, it is indispensable for India to formulate a legal
framework and to discuss safety, liability, and regulatory issues
surrounding GM foods in conformity to the provisions of the
Protocol. The liability mechanism is also important in the case where
the risk assessment and risk management is still in implementing
stage. Moreover, the country is facing GM infiltration issues with its
neighbors Bangladesh. As a precautionary approach, there is a need
to formulate rules and procedure of legal liability to discuss any kind
of damage occurs at transboundary trade. In this context, the
proposed work will attempt to analyze the liability regime in the
existing Food Safety and Standards Act, 2006 from the applicability
and domestic compliance and to suggest legal and policy options for
regulatory authorities.
Abstract: The strain intensity and redundant strains, dependent
in multistage TRIP wire drawing processes from values used single
partial reductions, should influence on the intensity of transformation
the retained austenite into martensite and thereby on mechanical
properties of drawn wires. The numerical analysis of drawing
processes with use of Drawing 2D programme, for steel wires made
from TRIP steel with 0,29% has been shown in the work. The change
of strain intensity εc and the values of redundant strain εxy, has been
determined for particular draws in dependence of used single partial
reductions.
Abstract: Average temperatures worldwide are expected to
continue to rise. At the same time, major cities in developing
countries are becoming increasingly populated and polluted.
Governments are tasked with the problem of overheating and air
quality in residential buildings. This paper presents the development
of a model, which is able to estimate the occupant exposure
to extreme temperatures and high air pollution within domestic
buildings. Building physics simulations were performed using the
EnergyPlus building physics software. An accurate metamodel is
then formed by randomly sampling building input parameters and
training on the outputs of EnergyPlus simulations. Metamodels are
used to vastly reduce the amount of computation time required when
performing optimisation and sensitivity analyses. Neural Networks
(NNs) have been compared to a Radial Basis Function (RBF)
algorithm when forming a metamodel. These techniques were
implemented using the PyBrain and scikit-learn python libraries,
respectively. NNs are shown to perform around 15% better than RBFs
when estimating overheating and air pollution metrics modelled by
EnergyPlus.
Abstract: This article discusses the passage of RDB to XML
documents (schema and data) based on metadata and semantic
enrichment, which makes the RDB under flattened shape and is
enriched by the object concept. The integration and exploitation of
the object concept in the XML uses a syntax allowing for the
verification of the conformity of the document XML during the
creation. The information extracted from the RDB is therefore
analyzed and filtered in order to adjust according to the structure of
the XML files and the associated object model. Those implemented
in the XML document through a SQL query are built dynamically. A
prototype was implemented to realize automatic migration, and so
proves the effectiveness of this particular approach.
Abstract: The purposes of this study were to: 1) investigate
operation conditions of SME automotive part industry in Bangkok
and vicinity and 2) to compare operation problem levels of SME
automotive part industry in Bangkok and vicinity according to the
sizes of the enterprises. Samples in this study included 196
entrepreneurs of SME automotive part industry in Bangkok and
vicinity derived from simple random sampling and calculation from
R. V. Krejcie and D. W. Morgan’s tables. Research statistics included
frequency, percentage, mean, standard deviation, and T-test. The
results revealed that in general the problem levels of SME automotive
part industry in Bangkok and vicinity were high. When considering
in details, it was found that the problem levels were high at every
aspect, i.e. personal, production, export, finance, and marketing
respectively. The comparison of the problem levels according to the
sizes of the enterprises revealed statistically significant differences at
.05. When considering on each aspect, it was found that the aspect
with the statistical difference at .05 included 5 aspects, i.e.
production, marketing, finance, personal, and export. The findings
also showed that small enterprises faced more severe problems than
those of medium enterprises.
Abstract: The increase in electric power demand in face of
environmental issues has intensified the participation of renewable
energy sources such as photovoltaics, in the energy matrix of various
countries. Due to their operational characteristics, they can generate
time-varying harmonic and inter-harmonic distortions. For this
reason, the application of methods of measurement based on
traditional Fourier analysis, as proposed by IEC 61000-4-7, can
provide inaccurate results. Considering the aspects mentioned herein,
came the idea of the development of this work which aims to present
the results of a comparative evaluation between a methodology
arising from the combination of the Prony method with the Kalman
filter and another method based on the IEC 61000-4-30 and IEC
61000-4-7 standards. Employed in this study were synthetic signals
and data acquired through measurements in a 50kWp photovoltaic
installation.
Abstract: The quality of concrete is usually defined by compressive strength, but flexural strength is the most important characteristic of concrete in a pavement which control the mix design of concrete instead of compressive strength. Therefore, the aggregates which are selected for the pavements are affected by higher flexural strength. Roller Compacting Concrete Pavement (RCCP) is not a new construction method. The other characteristic of this method is no bleeding and less shrinkage due to the lower amount of water. For this purpose, a roller is needed for placing and compacting. The surface of RCCP is not smooth; therefore, the most common use of this pavement is in an industrial zone with slower traffic speed which requires durable and tough pavement. For preparing a smoother surface, it can be achieved by asphalt paver. RCCP decrease the finishing cost because there are no bars, formwork, and the lesser labor need for placing the concrete. In this paper, different aspect of RCCP such as mix design, flexural, compressive strength and focus on the different part of RCCP on detail have been investigated.
Abstract: Carbon dioxide is one of the major greenhouse gas
(GHG) contributors. It is an obligation of the industry to reduce the
amount of carbon dioxide emission to the acceptable limits.
Tremendous research and studies are reported in the past and still the
quest to find the suitable and economical solution of this problem
needed to be explored in order to develop the most plausible absorber
for carbon dioxide removal. Amino acids can be potential alternate
solvents for carbon dioxide capture from gaseous streams. This is due
to its ability to resist oxidative degradation, low volatility and its
ionic structure. In addition, the introduction of promoter-like
piperazine to amino acid helps to further enhance the solubility. In
this work, the effect of piperazine on thermo physical properties and
solubility of β-Alanine aqueous solutions were studied for various
concentrations. The measured physicochemical properties data was
correlated as a function of temperature using least-squares method
and the correlation parameters are reported together with it respective
standard deviations. The effect of activator piperazine on the CO2
loading performance of selected amino acid under high-pressure
conditions (1bar to 10bar) at temperature range of (30 to 60)oC was
also studied. Solubility of CO2 decreases with increasing temperature
and increases with increasing pressure. Quadratic representation of
solubility using Response Surface Methodology (RSM) shows that
the most important parameter to optimize solubility is system
pressure. The addition of promoter increases the solubility effect of
the solvent.
Abstract: Dengue is a mosquito-borne viral disease endemic in
many countries in the tropics and sub-tropics. The state of Punjab in
India shows cyclical and seasonal variation in dengue cases. The
Case Fatality Rate of Dengue has ranged from 0.6 to 1.0 in the past
years. The department has initiated review of the cases that have died
due to dengue in order to know the exact cause of the death in a case
of dengue. The study has been undertaken to know the other
associated co-morbidities and factors causing death in a case of
dengue. The study used the predesigned proforma on which the
records (medical and Lab) were recorded and reviewed by the expert
committee of the doctors. This study has revealed that cases of
dengue having co-morbidities have longer stay in hospital. Fluid
overload and co-morbidities have been found as major factors leading
to death, however, in a confirmed case of dengue hepatorenal
shutdown was found to be major cause of mortality. The data
obtained will help in sensitizing the treating physicians in order to
decrease the mortality due to dengue in future.
Abstract: This paper presents the effect of the orbit inclination
on the pointing error of the satellite antenna and consequently on its
footprint on earth for a typical Ku- band payload system. The performance assessment is examined using both analytical
simulations and practical measurements, taking into account all the
additional sources of the pointing errors, such as East-West station
keeping, orbit eccentricity, and actual attitude control performance. An implementation and computation of the sinusoidal biases in
satellite roll and pitch used to compensate the pointing error of the
satellite antenna coverage is studied and evaluated before and after
the pointing corrections performed. A method for evaluation of the performance of the implemented
biases has been introduced through measuring satellite received level
from a mono-pulse tracking 11.1m transmitting antenna before and
after the implementation of the pointing corrections.