Abstract: This paper is intended to evaluate the structural performance of welded electronic road signs under various damage scenarios (DSs) using a finite element (FE) model calibrated with full-scale ultimate load testing results. The tested electronic road sign specimen was built with a back skin made of 5052 aluminum and two channels and a frame made of 6061 aluminum, where the back skin was connected to the frame by welding. The size of the tested specimen was 1.52 m long, 1.43 m wide, and 0.28 m deep. An actuator applied vertical loads at the center of the back skin of the specimen, resulting in a displacement of 158.7 mm and an ultimate load of 153.46 kN. Using these testing data, generation and calibration of a FE model of the tested specimen were executed in ABAQUS, indicating that the difference in the ultimate load between the calibrated model simulation and full-scale testing was only 3.32%. Then, six different DSs were simulated where the areas of the welded connection in the calibrated model were diminished for the DSs. It was found that the corners at the back skin-frame joint were prone to connection failure for all the DSs, and failure of the back skin-frame connection occurred remarkably from the distant edges.
Abstract: The present investigation is a study of the effect of advanced Physical Vapor Deposition (PVD) coatings on cutting temperature residual stresses and surface roughness during Duplex Stainless Steel (DSS) 2205 turning. Austenite stabilizers like nickel, manganese, and molybdenum reduced the cost of DSS. Surface Integrity (SI) plays an important role in determining corrosion resistance and fatigue life. Resistance to various types of corrosion makes DSS suitable for applications with critical environments like Heat exchangers, Desalination plants, Seawater pipes and Marine components. However, lower thermal conductivity, poor chip control and non-uniform tool wear make DSS very difficult to machine. Cemented carbide tools (M grade) were used to turn DSS in a dry environment. AlTiN and AlTiCrN coatings were deposited using advanced PVD High Pulse Impulse Magnetron Sputtering (HiPIMS) technique. Experiments were conducted with cutting speed of 100 m/min, 140 m/min and 180 m/min. A constant feed and depth of cut of 0.18 mm/rev and 0.8 mm were used, respectively. AlTiCrN coated tools followed by AlTiN coated tools outperformed uncoated tools due to properties like lower thermal conductivity, higher adhesion strength and hardness. Residual stresses were found to be compressive for all the tools used for dry turning, increasing the fatigue life of the machined component. Higher cutting temperatures were observed for coated tools due to its lower thermal conductivity, which results in very less tool wear than uncoated tools. Surface roughness with uncoated tools was found to be three times higher than coated tools due to lower coefficient of friction of coating used.
Abstract: Intrusion detection systems (IDS) are the main components of network security. These systems analyze the network events for intrusion detection. The design of an IDS is through the training of normal traffic data or attack. The methods of machine learning are the best ways to design IDSs. In the method presented in this article, the pruning algorithm of C5.0 decision tree is being used to reduce the features of traffic data used and training IDS by the least square vector algorithm (LS-SVM). Then, the remaining features are arranged according to the predictor importance criterion. The least important features are eliminated in the order. The remaining features of this stage, which have created the highest level of accuracy in LS-SVM, are selected as the final features. The features obtained, compared to other similar articles which have examined the selected features in the least squared support vector machine model, are better in the accuracy, true positive rate, and false positive. The results are tested by the UNSW-NB15 dataset.
Abstract: The concept of urban metabolism has increasingly been employed in a diverse range of disciplines as a mean to analyze and theorize the city. Urban ecology has a particular focus on the implications of applying the metabolism concept to the urban realm. This approach has been developed by a few researchers, though it has rarely if ever been used in policy development for city planning. The aim of this research is to use ecologically informed urban planning interventions to increase the sustainability of urban metabolism; with special focus on land stock as a most important city resource by developing a system dynamic based DSS. This model identifies two critical management strategy variables for the Strategic Urban Plan Alexandria SUP 2032. As a result, this comprehensive and precise quantitative approach is needed to monitor, measure, evaluate and observe dynamic urban changes working as a decision support system (DSS) for policy making.
Abstract: Cloud computing provides infrastructure to the enterprise through the Internet allowing access to cloud services at anytime and anywhere. This pervasive aspect of the services, the distributed nature of data and the wide use of information make cloud computing vulnerable to intrusions that violate the security of the cloud. This requires the use of security mechanisms to detect malicious behavior in network communications and hosts such as intrusion detection systems (IDS). In this article, we focus on the detection of intrusion into the cloud sing IDSs. We base ourselves on client authentication in the computing cloud. This technique allows to detect the abnormal use of ubiquitous service and prevents the intrusion of cloud computing. This is an approach based on client authentication data. Our IDS provides intrusion detection inside and outside cloud computing network. It is a double protection approach: The security user node and the global security cloud computing.
Abstract: Multiple Sclerosis (MS) is a disease which affects the
central nervous system and causes balance problem. In clinical, this
disorder is usually evaluated using static posturography. Some linear
or nonlinear measures, extracted from the posturographic data (i.e.
center of pressure, COP) recorded during a balance test, has been
used to analyze postural control of MS patients. In this study, the
trend (TREND) and the sample entropy (SampEn), two nonlinear
parameters were chosen to investigate their relationships with the
expanded disability status scale (EDSS) score. 40 volunteers with
different EDSS scores participated in our experiments with eyes open
(EO) and closed (EC). TREND and 2 types of SampEn (SampEn1
and SampEn2) were calculated for each combined COP’s position
signal. The results have shown that TREND had a weak negative
correlation to EDSS while SampEn2 had a strong positive correlation
to EDSS. Compared to TREND and SampEn1, SampEn2 showed a
better significant correlation to EDSS and an ability to discriminate
the MS patients in the EC case. In addition, the outcome of the study
suggests that the multi-dimensional nonlinear analysis could provide
some information about the impact of disability progression in MS on
dynamics of the COP data.
Abstract: Dengue is a mosquito-borne viral disease endemic in
many countries in the tropics and sub-tropics. The state of Punjab in
India shows cyclical and seasonal variation in dengue cases. The
Case Fatality Rate of Dengue has ranged from 0.6 to 1.0 in the past
years. The department has initiated review of the cases that have died
due to dengue in order to know the exact cause of the death in a case
of dengue. The study has been undertaken to know the other
associated co-morbidities and factors causing death in a case of
dengue. The study used the predesigned proforma on which the
records (medical and Lab) were recorded and reviewed by the expert
committee of the doctors. This study has revealed that cases of
dengue having co-morbidities have longer stay in hospital. Fluid
overload and co-morbidities have been found as major factors leading
to death, however, in a confirmed case of dengue hepatorenal
shutdown was found to be major cause of mortality. The data
obtained will help in sensitizing the treating physicians in order to
decrease the mortality due to dengue in future.
Abstract: This paper investigates the problem of sampling from transactional data streams. We introduce CFISDS as a content based sampling algorithm that works on a landmark window model of data streams and preserve more informed sample in sample space. This algorithm that work based on closed frequent itemset mining tasks, first initiate a concept lattice using initial data, then update lattice structure using an incremental mechanism.Incremental mechanism insert, update and delete nodes in/from concept lattice in batch manner. Presented algorithm extracts the final samples on demand of user. Experimental results show the accuracy of CFISDS on synthetic and real datasets, despite on CFISDS algorithm is not faster than exist sampling algorithms such as Z and DSS.
Abstract: In this paper, we present user pattern learning
algorithm based MDSS (Medical Decision support system) under
ubiquitous. Most of researches are focus on hardware system, hospital
management and whole concept of ubiquitous environment even
though it is hard to implement. Our objective of this paper is to design
a MDSS framework. It helps to patient for medical treatment and
prevention of the high risk patient (COPD, heart disease, Diabetes).
This framework consist database, CAD (Computer Aided diagnosis
support system) and CAP (computer aided user vital sign prediction
system). It can be applied to develop user pattern learning algorithm
based MDSS for homecare and silver town service. Especially this
CAD has wise decision making competency. It compares current vital
sign with user-s normal condition pattern data. In addition, the CAP
computes user vital sign prediction using past data of the patient. The
novel approach is using neural network method, wireless vital sign
acquisition devices and personal computer DB system. An intelligent
agent based MDSS will help elder people and high risk patients to
prevent sudden death and disease, the physician to get the online
access to patients- data, the plan of medication service priority (e.g.
emergency case).
Abstract: Most Decision Support Systems (DSS) for waste
management (WM) constructed are not widely marketed and lack
practical applications. This is due to the number of variables and
complexity of the mathematical models which include the
assumptions and constraints required in decision making. The
approach made by many researchers in DSS modelling is to isolate a
few key factors that have a significant influence to the DSS. This
segmented approach does not provide a thorough understanding of
the complex relationships of the many elements involved. The
various elements in constructing the DSS must be integrated and
optimized in order to produce a viable model that is marketable and
has practical application. The DSS model used in assisting decision
makers should be integrated with GIS, able to give robust prediction
despite the inherent uncertainties of waste generation and the plethora
of waste characteristics, and gives optimal allocation of waste stream
for recycling, incineration, landfill and composting.
Abstract: This conference paper discusses a risk allocation problem for subprime investing banks involving investment in subprime structured mortgage products (SMPs) and Treasuries. In order to solve this problem, we develop a L'evy process-based model of jump diffusion-type for investment choice in subprime SMPs and Treasuries. This model incorporates subprime SMP losses for which credit default insurance in the form of credit default swaps (CDSs) can be purchased. In essence, we solve a mean swap-at-risk (SaR) optimization problem for investment which determines optimal allocation between SMPs and Treasuries subject to credit risk protection via CDSs. In this regard, SaR is indicative of how much protection investors must purchase from swap protection sellers in order to cover possible losses from SMP default. Here, SaR is defined in terms of value-at-risk (VaR). Finally, we provide an analysis of the aforementioned optimization problem and its connections with the subprime mortgage crisis (SMC).