Abstract: Heat transfer of leaves is a crucial factor in optimal
operation of metabolic functions in plants. In order to quantify this
phenomenon in different leaves and investigate the influence of leaf
shape on heat transfer, natural convection for pine, orange and olive
leaves was simulated as representatives of different groups of leaf
shapes. CFD techniques were used in this simulation with the
purpose to calculate heat transfer of leaves in similar environmental
conditions. The problem was simulated for steady state and threedimensional
conditions. From obtained results, it was concluded that
heat fluxes of all three different leaves are almost identical, however,
total rate of heat transfer have highest and lowest values for orange
leaves, and pine leaves, respectively.
Abstract: Pt/γ-Al2O3 membrane catalysts were prepared via an
evaporative-crystallization deposition method. The obtained Pt/γ-
Al2O3 catalyst activity was tested after characterization (SEM-EDAX
observation, BET measurement, permeability assessment) in the
catalytic oxidation of selected volatile organic compound (VOC) i.e.
propane, fed in mixture of oxygen. The VOC conversion (nearly
90%) obtained by varying the operating temperature showed that
flow-through membrane reactor might do better in the abatement of
VOCs.
Abstract: An unconventional composite inorganic ceramic
membrane capable of enhancing carbon dioxide emission decline was
fabricated and tested at laboratory scale in conformism to various
environmental guidelines and also to mitigate the effect of global
warming. A review of the existing membrane technologies for carbon
capture including the relevant gas transport mechanisms is presented.
Single gas permeation experiments using silica modified ceramic
membrane with internal diameter 20mm, outside diameter 25mm and
length of 368mm deposited on a macro porous support was carried
out to investigate individual gas permeation behaviours at different
pressures at room temperature. Membrane fabrication was achieved
using after a dip coating method. Nitrogen, Carbon dioxide, Argon,
Oxygen and Methane pure gases were used to investigate their
individual permeation rates at various pressures. Results show that
the gas flow rate increases with pressure drop. However above a
pressure of 3bar, CO2 permeability ratio to that of the other gases
indicated control of a more selective surface adsorptive transport
mechanism.
Abstract: Roadway planning and design is a very complex
process involving five key phases before a project is completed;
planning, project development, final design, right-of-way, and
construction. The planning phase for a new roadway transportation
project is a very critical phase as it greatly affects all latter phases of
the project. A location study is usually performed during the
preliminary planning phase in a new roadway project. The objective
of the location study is to develop alignment alternatives that are cost
efficient considering land acquisition and construction costs. This
paper describes a methodology to develop optimal preliminary
roadway alignments utilizing spatial-data. Four optimization criteria
are taken into consideration; roadway length, land cost, land slope,
and environmental impacts. The basic concept of the methodology is
to convert the proposed project area into a grid, which represents the
search space for an optimal alignment. The aforementioned
optimization criteria are represented in each of the grid’s cells. A
spatial-data optimization technique is utilized to find the optimal
alignment in the search space based on the four optimization criteria.
Two case studies for new roadway projects in Duval County in the
State of Florida are presented to illustrate the methodology. The
optimization output alignments are compared to the proposed Florida
Department of Transportation (FDOT) alignments. The comparison is
based on right-of-way costs for the alignments. For both case studies,
the right-of-way costs for the developed optimal alignments were
found to be significantly lower than the FDOT alignments.
Abstract: This work sets out to debate the tensions involved in
the processes of contamination and self-purification in the urban
space, particularly in the streams that run through the Buenos Aires
metropolitan area. For much of their course, those streams are piped;
their waters do not come into contact with the outdoors until they
have reached deeply impoverished urban areas with high levels of
environmental contamination. These are peripheral zones that, until
thirty years ago, were marshlands and fields. They are now densely
populated areas largely lacking in urban infrastructure.
The Cárcova neighborhood, where this project is underway, is in
the José León Suárez section of General San Martín county, Buenos
Aires province. A stretch of José León Suarez canal crosses the
neighborhood. Starting upstream, this canal carries pollutants due to
the sewage and industrial waste released into it. Further downstream,
in the neighborhood, domestic drainage is poured into the stream. In
this paper, we formulate a hypothesis diametrical to the one that
holds that these neighborhoods are the primary source of
contamination, suggesting instead that in the stretch of the canal that
runs through the neighborhood the stream’s waters are actually
cleaned and the sediments accumulate pollutants. Indeed, the
stretches of water that runs through these neighborhoods act as water
processing plants for the metropolis.
This project has studied the different organic-load polluting
contributions to the water in a certain stretch of the canal, the
reduction of that load over the course of the canal, and the
incorporation of pollutants into the sediments. We have found that
the surface water has considerable ability to self-purify, mostly due to
processes of sedimentation and adsorption. The polluting load is
accumulated in the sediments where that load stabilizes slowly by
means of anaerobic processes. In this study, we also investigated the
risks of sediment management and the use of the processes studied
here in controlled conditions as tools of environmental restoration.
Abstract: Coal fly ash is formed as a solid waste product from
the combustion of coal in coal fired power stations. Huge amounts of
fly ash are produced globally every year and are predicted to
increase. Nowadays, less than half of the fly ash is used as a raw
material for cement manufacturing, construction and the rest of it is
disposed as a waste causing yet another environmental concern. For
this reason, the recycling of this kind of slurries into useful materials
is quite important in terms of economical and environmental aspects.
The purpose of this study is to evaluate the Orhaneli and
Tuncbilek coal fly ashes for utilization in some industrial
applications. Therefore the mineralogical and chemical compositions
of these fly ashes were analyzed by X-ray fluorescence spectroscopy,
ourier-transform infrared spectrometer, and X-ray diffraction. The
silicon (Si) and aluminum (Al) in the fly ashes were activated by
alkali fusion technique with sodium hydroxide. The obtained extracts
were analyzed for Si and Al content by inductively coupled plasma
optical emission spectrometry.
Abstract: This study was carried out to investigate the adverse
effect of industrial wastewater on surface water quality in Gebeng
industrial estate, Pahang, Malaysia. Surface water was collected from
six sampling stations. Physicochemical parameters were
characterized based on in-situ and ex-situ analysis according to
standard methods by American Public Health Association (APHA).
Selected heavy metals were determined by using Inductively Coupled
Plasma Mass Spectrometry (ICP MS). The results revealed that the
concentration of heavy metals such as Pb, Cu, Cd, Cr and Hg were
high in samples. The results also showed that the value of Pb and Hg
were higher in the wet season in comparison to dry season.
According to Malaysia National Water Quality Standard (NWQS)
and Water Quality Index (WQI) all the sampling station were
categorized as class IV (highly polluted). The present study revealed
that the adverse effects of careless disposal of wastes and directly
discharge of effluents affected on surface water quality. Therefore,
the authorities should implement the laws to ensure the proper
practices of wastewater management for environmental sustainability
around the study area.
Abstract: Chrome tannery wastewater causes serious environmental hazard due to its high pollution potential. As a result, rigorous treatment is necessary for abatement of pollution from this type of wastewater. There are many research studies on chrome tannery wastewater treatment in the field of physical, chemical, and biological methods. In general, biological treatment process is found ineffective for direct application because of adverse effects by toxic chromium, sulphide, chloride etc. However, biological methods were employed mainly for a few sub processes generating significant amount of organic matter and without chromium, chlorides etc. In this context the present paper reviews the characteristics feature and pollution potential of wastewater generated from chrome tannery units and treatment of the same. The different biological processes used earlier and their chronological development for treatment of the chrome tannery wastewater are thoroughly reviewed in this paper. In this regard, the scope of hybrid bioreactor - an advanced technology option has also been explored, as this kind of treatment is well suited for the wastewater having inhibitory substances.
Abstract: Investigations on the accumulation of heavy metals in
water and sediments of river Ogbese were carried out between
December 2010 and February 2011 using Atomic Absorption
Spectrophotometer. Etheria elliptica a sessile organism was also used
to determine the concentration of heavy metal in the aquatic
environmental. In water, Cu had the highest concentration (0.55 –
0.13 mg/l ±0.1) while in sediments, the highest value obtained was in
Fe (1.46-3.89mg/l±0.27). The minimum concentrations recorded
were in Pb; which was below detectable level. The result also
revealed that the shell accumulate more heavy metals than the flesh
of the mussel with Cu in the shell exhibiting a negative correlation
with all the metals in the flesh. However, the condition factor (K)
value is 6.44, an indication of good health. The length-weight
relationship is expressed as W = -0.48 x L 1.94 (r2 = 0.29) showing the
growth pattern to be negatively allometric.
Abstract: The present work attempts to investigate the
combustion, performance and emission characteristics of an existing
single-cylinder four-stroke compression-ignition engine operated in
dual-fuel mode with hydrogen as an alternative fuel. Environmental
concerns and limited amount of petroleum fuels have caused interests
in the development of alternative fuels like hydrogen for internal
combustion (IC) engines. In this experimental investigation, a diesel
engine is made to run using hydrogen in dual fuel mode with diesel,
where hydrogen is introduced into the intake manifold using an LPGCNG
injector and pilot diesel is injected using diesel injectors. A
Timed Manifold Injection (TMI) system has been developed to vary
the injection strategies. The optimized timing for the injection of
hydrogen was 10^0 CA after top dead center (ATDC). From the study
it was observed that with increasing hydrogen rate, enhancement in
brake thermal efficiency (BTHE) of the engine has been observed
with reduction in brake specific energy consumption (BSEC).
Furthermore, Soot contents decrease with an increase in indicated
specific NOx emissions with the enhancement of hydrogen flow rate.
Abstract: The paper is focused on the identification of limiting
environmental factors of individual industrial floors on which newly
developed polymer protection and repair systems with the use of
secondary raw materials will be used. These mainly include floors
with extreme stresses and special requirements for materials used. In
relation to the environment of a particular industrial floor, it is
necessary to ensure, for example, chemical stability, resistance to
higher temperatures, resistance to higher mechanical stress, etc. for
developed materials, which is reflected in the demands for the
developed material systems. The paper describes individual
environments and, in relation to them, also requirements for
individual components of the developed materials and for the
developed materials as a whole.
Abstract: In emerging economies, recycling is an opportunity
for the cities to increase the lifespan of sanitary landfills, reduce the
costs of the solid waste management, decrease the environmental
problems of the waste treatment through reincorporate waste in the
productive cycle and protect and develop people’s livelihoods of
informal waste pickers. However, few studies have analysed the
possibilities and strategies to integrate formal and informal sectors in
the solid waste management for the benefit of both. This study seek
to make a strength, weakness, opportunity, and threat (SWOT)
analysis in three recycling associations of Bogotá with the aim to
understand and determine the situation of recycling from perspective
of informal sector in its transition to enter as authorized waste
providers. Data used in the analysis are derived from multiple
strategies such as literature review, the Bogota’s recycling database,
focus group meetings, governmental reports, national laws and
regulations and specific interviews with key stakeholders. Results of
this study show as the main stakeholders of formal and informal
sector of waste management can identify the internal and internal
conditions of recycling in Bogotá. Several strategies were designed
based on the SWOTs determined, could be useful for Bogotá to
advance and promote recycling as a key strategy for integrated
sustainable waste management in the city.
Abstract: The textile industry plays a major role in the economy
of India and on the other side of the coin it is the major source for
water pollution. As azo dyes is the largest dye class they are
extensively used in many fields such as textile industry, leather
tanning industry, paper production, food, color photography,
pharmaceuticals and medicine, cosmetic, hair colorings, wood
staining, agricultural, biological and chemical research etc. In
addition to these, they can have acute and/or chronic effects on
organisms depending on their concentration and length of exposure
when they discharged as effluent in the environment. The aim of this
study was to assess the genotoxic and histotoxic potentials of
environmentally relevant concentrations of C. I. Reactive Red 120
(RR 120) on Catla catla, important edible freshwater fingerlings. For
this, healthy Catla catla fingerlings were procured from the
Government Fish Farm and acclimatized in 100 L capacity and
continuously aerated glass aquarium in laboratory for 15 days.
According to APHA some physic-chemical parameters were
measured and maintained such as temperature, pH, dissolve oxygen,
alkalinity, total hardness. Water along with excreta had been changed
every 24 hrs. All fingerlings were fed artificial food palates once a
day @ body weight. After 15 days fingerlings were grouped in 5 (10
in each) and exposed to various concentrations of RR 120 (Control,
10, 20, 30 and 40 mg.l-1) and samples (peripheral blood and gills,
kidney) were collected and analyzed at 96 hrs. All results were
compared with the control. Micronuclei (MN), nuclear buds (NB),
fragmented-apoptotic (FA) and bi-nucleated (BN) cells in blood
smears and in tissues (gills and kidney cells) were observed.
Prominent histopathological alterations were noticed in gills such as
aneurism, hyperplasia, degenerated central axis, lifting of gill
epithelium, curved secondary gill lamellae etc. Similarly kidney
showed some detrimental changes like shrunken glomeruli with
increased periglomerular space, degenerated renal tubules etc. Both
haematological and histopathological changes clearly reveal the toxic
potential of RR 120. This work concludes that water pollution
assessment can be done by these two biomarkers which provide
baseline to the further chromosomal or molecular work.
Abstract: The design philosophy of building structure has been
changing time to time. The reason for this is because of an increase of
human inertest, an improved building materials and technology that
will impact how we live, to speed up construction period and natural
effect which includes earthquake disasters and environmental effect.
One technique which takes in to account the above case is using a
prefabricable structural system. In which each and every structural
element is designed and prefabricated and assembled on a site so that
the construction speed is increased and the environmental impact is
also enhanced. This system has an immense advantage such as: reduce
construction cost, reusable, recyclable, speed up construction period
and less environmental effect. In this study, it is tried to present some
of the developed and evaluated structural elements of building
structures.
Abstract: The biodegradable family of polymers
polyhydroxyalkanoates is an interesting substitute for convectional
fossil-based plastics. However, the manufacturing and environmental
impacts associated with their production via intracellular bacterial
fermentation are strongly dependent on the raw material used and on
energy consumption during the extraction process, limiting their
potential for commercialization. Industrial wastewater is studied in
this paper as a promising alternative feedstock for waste valorization.
Based on results from laboratory and pilot-scale experiments, a
conceptual process design, techno-economic analysis and life cycle
assessment are developed for the large-scale production of the most
common type of polyhydroxyalkanoate, polyhydroxbutyrate.
Intracellular polyhydroxybutyrate is obtained via fermentation of
microbial community present in industrial wastewater and the
downstream processing is based on chemical digestion with
surfactant and hypochlorite. The economic potential and
environmental performance results help identifying bottlenecks and
best opportunities to scale-up the process prior to industrial
implementation. The outcome of this research indicates that the
fermentation of wastewater towards PHB presents advantages
compared to traditional PHAs production from sugars because the
null environmental burdens and financial costs of the raw material in
the bioplastic production process. Nevertheless, process optimization
is still required to compete with the petrochemicals counterparts.
Abstract: Poly bag and mulch films for agricultural field caused
pose environmental problem due to the non-degradable plastics
wastes upon disposal. Thus, a degradable poly bag was designed with
hybrid sago starch (SS) and polyvinyl alcohol (PVA). Two Different
blended compositions of SS and PVA hybrid have been compounded.
Then, the hybrids blended are mixed with linear line density
polyethylene (LLDPE) resin to fabricate poly bag film through
conventional film blowing process. Samples of LLDPE, SS and PVA
hybrid film were exposed to UV light and soil burial. The weight
losses were determined during degradation process. Hybrid film by
degradation of starch was found to hydrolyze and hydroxyl groups
decrease on esterification upon exposure to soil burial and uv
radiation. It was found out that, the hybrid film for 60% of SS
composition showed greatest degradation in soil and UV radiation.
Abstract: Freshly laid eggs from green turtles, Chelonia mydas,
were randomly collected from Ras Al-Hadd Reserve, Oman.
Eggshells taken from eggs and sand collected from the body chamber
were analyzed for eight heavy metals (Al, Br, Cd, Co, Cu, Fe, S, and
Zn) using inductively coupled plasma mass spectrometry (ICP).
Heavy metal concentrations varied significantly (P
Abstract: The introduction of degradable plastic materials into
agricultural sectors has represented a promising alternative to
promote green agriculture and environmental friendly of modern
farming practices. Major challenges of developing degradable
agricultural films are to identify the most feasible types of
degradation mechanisms, composition of degradable polymers and
related processing techniques. The incorrect choice of degradable
mechanisms to be applied during the degradation process will cause
premature losses of mechanical performance and strength. In order to
achieve controlled process of agricultural film degradation, the
compositions of degradable agricultural film also important in order
to stimulate degradation reaction at required interval of time and to
achieve sustainability of the modern agricultural practices. A set of
photodegradable polyethylene based agricultural film was developed
and produced, following the selective optimization of processing
parameters of the agricultural film manufacturing system. Example of
agricultural films application for oil palm seedlings cultivation is
presented.
Abstract: This paper discusses the value theory in cultural
heritage and the value theory in environmental economics. Two
economic views of the value theory are compared, within the field of
cultural heritage maintenance and within the field of the environment.
The main aims are to find common features in these two differently
structured theories under the layer of differently defined terms as well
as really differing features of these two approaches; to clear the
confusion which stems from different terminology as in fact these
terms capture the same aspects of reality; and to show possible
inspiration these two perspectives can offer one another. Another aim
is to present these two value systems in one value framework. First,
important moments of the value theory from the economic
perspective are presented, leading to the marginal revolution of (not
only) the Austrian School. Then the theory of value within cultural
heritage and environmental economics are explored. Finally,
individual approaches are compared and their potential mutual
inspiration searched for.
Abstract: International and domestic environmental law has
evolved quite rapidly in the last few decades. At the international
level the Stockholm and Rio Declarations paved the way for a broad
based consensus of the international community on environmental
issues and principles. At the Domestic level also many states have
incorporated environmental protection in their constitutions and even
more states are doing the same at least in their domestic legislations.
In this process of evolution environmental law has unleashed a
number of novel principles such as; the participatory principle, the
polluter pays principle, the precautionary principle, the intergenerational
and intra-generational principles, the prevention
principle, the sustainable development principle and so on.