Abstract: The present article deals with a composite casting process that allows to produce bilayer AlSn6-Al strips based on the technique of horizontal continuous casting. In the first part experimental investigations on the production of a single layer AlSn6 strip are described. Afterwards essential results of basic compound casting trials using simple test specimen are presented to define the thermal conditions required for a metallurgical compound between the alloy AlSn6 and pure aluminium. Subsequently, numerical analyses are described. A finite element model was used to examine a continuous composite casting process. As a result of the simulations the main influencing parameters concerning the thermal conditions within the composite casting region could be pointed out. Finally, basic guidance is given for the design of an appropriate composite mould system.
Abstract: Metal cutting is a severe plastic deformation process
involving large strains, high strain rates, and high temperatures.
Conventional analysis of the chip formation process is based on bulk
material deformation disregarding the inhomogeneous nature of the
material microstructure. A series of orthogonal cutting tests of AISI
1045 and 1144 steel were conducted which yielded similar process
characteristics and chip formations. With similar shear angles and cut
chip thicknesses, shear strains for both chips were found to range
from 2.0 up to 2.8. The manganese-sulfide (MnS) precipitate in the
1144 steel has a very distinct and uniform shape which allows for
comparison before and after chip formation. From close observations
of MnS precipitates in the cut chips it is shown that the conventional
approach underestimates plastic strains in metal cutting.
Experimental findings revealed local shear strains around a value of
6. These findings and their implications are presented and discussed.
Abstract: One year (November 2009-October 2010) sediment monitoring was used to evaluate pollution status, concentration and distribution of heavy metals (As, Cu, Cd, Cr, Hg, Ni, Pb and Zn) in West Port of Malaysia. Sediment sample were collected from nine stations every four months. Geo-accumulation factor and Pollution Load Index (PLI) were estimated to better understand the pollution level in study area. The heavy metal concentration (Mg/g dry weight) were ranged from 20.2 to 162 for As, 7.4 to 27.6 for Cu, 0.244 to 3.53 for Cd, 11.5 to 61.5 for Cr, 0.11 to 0.409 for Hg, 7.2 to 22.2 for Ni, 22.3 to 80 for Pb and 23 to 98.3 for Zn. In general, concentration some metals (As,Cd, Hg and Pb) was higher than background values that are considered as serious concern for aquatic life and the human health.
Abstract: In a metal forming process, the friction between the
material and the tools influences the process by modifying the stress
distribution of the workpiece. This frictional behaviour is often taken
into account by using a constant coefficient of friction in the finite
element simulations of sheet metal forming processes. However,
friction coefficient varies in time and space with many parameters.
The Stribeck friction model is investigated in this study to predict
springback behaviour of AA6061-T4 sheets during V-bending
process. The coefficient of friction in Stribeck curve depends on
sliding velocity and contact pressure. The plane-strain bending
process is simulated in ABAQUS/Standard. We compared the
computed punch load-stroke curves and springback related to the
constant coefficient of friction with the defined friction model. The
results clearly showed that the new friction model provides better
agreement between experiments and results of numerical simulations.
The influence of friction models on stress distribution in the
workpiece is also studied numerically
Abstract: The paper presents a novel method for the 3D shaping
of different materials using a high-pressure abrasive water jet and a
flat target image. For steering movement process of the jet a principle
similar to raster image way of record and readout was used.
However, respective colors of pixel of such a bitmap are connected
with adequate jet feed rate that causes erosion of material with
adequate depth. Thanks to that innovation, one can observe spatial
imaging of the object. Theoretical basis as well as spatial model of
material shaping and experimental stand including steering program
are presented in. There are also presented methodic and some
experimental erosion results as well as practical example of object-s
bas-relief made of metal.
Abstract: Aiming the application of localized hyperthermia, a
magnetic induction system with new approaches is proposed. The techniques in this system for improving the effectiveness of localized hyperthermia are that using magnetic circuit and the multiple-coil array instead of a giant coil for generating magnetic field. Specially, amorphous metal is adopted as the material of magnetic circuit. Detail
design parameters of hardware are well described. Simulation tool is
employed for this work and experiment result is reported as well.
Abstract: Porcine production in China represents approximately
the 50% of the worldwide pig production. Information about pig
husbandry characteristics in China and manure properties from sows
to fatteners in intensive pig farms are not broadly available for
scientific studies as it is a time consuming, expensive task and highly
inaccessible. This study provides a report about solid pig manures
(28% dry matter) in a commercial pig farm located in the peri-urban
area of Beijing as well as a general overview of the current pig
husbandry techniques including pig breeds, feeds, diseases, housing as
well as pig manure and wastewater disposal. The main results are
intended to serve as a literature source for young scientists in order to
understand the main composition of pig manures as well as to identify
the husbandry techniques applied in an intensive pig farm in Beijing.
Abstract: The potential of economically cheaper cellulose
containing natural materials like rice husk was assessed for nickel
adsorption from aqueous solutions. The effects of pH, contact time,
sorbent dose, initial metal ion concentration and temperature on the
uptake of nickel were studied in batch process. The removal of nickel
was dependent on the physico-chemical characteristics of the
adsorbent, adsorbate concentration and other studied process
parameters. The sorption data has been correlated with Langmuir,
Freundlich and Dubinin-Radush kevich (D-R) adsorption models. It
was found that Freundlich and Langmuir isotherms fitted well to the
data. Maximum nickel removal was observed at pH 6.0. The
efficiency of rice husk for nickel removal was 51.8% for dilute
solutions at 20 g L-1 adsorbent dose. FTIR, SEM and EDAX were
recorded before and after adsorption to explore the number and
position of the functional groups available for nickel binding on to
the studied adsorbent and changes in surface morphology and
elemental constitution of the adsorbent. Pseudo-second order model
explains the nickel kinetics more effectively. Reusability of the
adsorbent was examined by desorption in which HCl eluted 78.93%
nickel. The results revealed that nickel is considerably adsorbed on
rice husk and it could be and economic method for the removal of
nickel from aqueous solutions.
Abstract: Vertical Double Gate (DG) Metal Oxide Semiconductor Field Effect Transistor (MOSFET) is believed to suppress various short channel effect problems. The gate to channel coupling in vertical DG-MOSFET are doubled, thus resulting in higher current density. By having two gates, both gates are able to control the channel from both sides and possess better electrostatic control over the channel. In order to ensure that the transistor possess a superb turn-off characteristic, the subs-threshold swing (SS) must be kept at minimum value (60-90mV/dec). By utilizing SILVACO TCAD software, an n-channel vertical DG-MOSFET was successfully designed while keeping the sub-threshold swing (SS) value as minimum as possible. From the observation made, the value of sub-threshold swing (SS) was able to be varied by adjusting the height of the silicon pillar. The minimum value of sub-threshold swing (SS) was found to be 64.7mV/dec with threshold voltage (VTH) of 0.895V. The ideal height of the vertical DG-MOSFET pillar was found to be at 0.265 µm.
Abstract: Regarding previous research studies it was concluded
that thin-walled fiber-cement composites are able to conduct electric
current under specific conditions. This property is ensured by using
of various kinds of carbon materials. Though carbon fibers are less
conductive than metal fibers, composites with carbon fibers were
evaluated as better current conductors than the composites with metal
fibers. The level of electric conductivity is monitored by the means of
impedance measurement of designed samples. These composites
could be used for a range of applications such as heating of
trafficable surfaces or shielding of electro-magnetic fields.
The aim of the present research was to design an element with the
ability to monitor internal processes in building structures and
prevent them from collapsing. As a typical element for laboratory
testing there was chosen a concrete column, which was repeatedly
subjected to load by simple pressure with continual monitoring of
changes in electrical properties.
Abstract: Equal Channel Angular Pressing (ECAP) is currently
being widely investigated because of its potential to produce ultrafine
grained microstructures in metals and alloys. A sound
knowledge of the plastic deformation and strain distribution is
necessary for understanding the relationships between strain
inhomogeneity and die geometry. Considerable research has been
reported on finite element analysis of this process, assuming threedimensional
plane strain condition. However, the two-dimensional
models are not suitable due to the geometry of the dies, especially in
cylindrical ones. In the present work, three-dimensional simulation of
ECAP process was carried out for six outer corner radii (sharp to 10
mm in steps of 2 mm), with channel angle 105¶Çü▒, for strain hardening
aluminium alloy (AA 6101) using ABAQUS/Standard software.
Strain inhomogeneity is presented and discussed for all cases. Pattern
of strain variation along selected radial lines in the body of the workpiece
is presented. It is found from the results that the outer corner
has a significant influence on the strain distribution in the body of
work-piece. Based on inhomogeneity and average strain criteria,
there is an optimum outer corner radius.
Abstract: The Mahin area is a part of Tarom- Hashtjin zone that
located in west of Qazvin province in northwest of Iran. Many copper
and base metals ore deposits are hosted by this zone. High potential
localities identification in this area is very necessary. The objective of
this research, is finding hydrothermal alteration zones by remote
sensing methods and best processing technique of Advanced
Spaceborne Thermal Emission and Reflection Radiometer (ASTER)
data. Different methods such as band ratio, Principal Component
Analysis (PCA), Minimum Noise Fraction (MNF) and Least Square
Fit (LS-Fit) were used for mapping hydrothermal alteration zones.
Abstract: This research presents the development of simulation
modeling for WIP management in semiconductor fabrication.
Manufacturing simulation modeling is needed for productivity
optimization analysis due to the complex process flows involved
more than 35 percent re-entrance processing steps more than 15 times
at same equipment. Furthermore, semiconductor fabrication required
to produce high product mixed with total processing steps varies from
300 to 800 steps and cycle time between 30 to 70 days. Besides the
complexity, expansive wafer cost that potentially impact the
company profits margin once miss due date is another motivation to
explore options to experiment any analysis using simulation
modeling. In this paper, the simulation model is developed using
existing commercial software platform AutoSched AP, with
customized integration with Manufacturing Execution Systems
(MES) and Advanced Productivity Family (APF) for data collections
used to configure the model parameters and data source. Model
parameters such as processing steps cycle time, equipment
performance, handling time, efficiency of operator are collected
through this customization. Once the parameters are validated, few
customizations are made to ensure the prior model is executed. The
accuracy for the simulation model is validated with the actual output
per day for all equipments. The comparison analysis from result of
the simulation model compared to actual for achieved 95 percent
accuracy for 30 days. This model later was used to perform various
what if analysis to understand impacts on cycle time and overall
output. By using this simulation model, complex manufacturing
environment like semiconductor fabrication (fab) now have
alternative source of validation for any new requirements impact
analysis.
Abstract: We design and discuss metal-dielectric antireflection coating on metallic substrates for Solar Selective Absorbers of Concentrating Solar Power Systems. The average reflectance is 8.5% at 400-3000nm and 84.4% at 3000nm-10000nm of the metal-dielectric structure.
Abstract: The agriculture lignocellulosic by-products are receiving increased attention, namely in the search for filter materials that retain contaminants from water. These by-products, specifically almond and hazelnut shells are abundant in Portugal once almond and hazelnuts production is a local important activity. Hazelnut and almond shells have as main constituents lignin, cellulose and hemicelluloses, water soluble extractives and tannins. Along the adsorption of heavy metals from contaminated waters, water soluble compounds can leach from shells and have a negative impact in the environment. Usually, the chemical characterization of treated water by itself may not show environmental impact caused by the discharges when parameters obey to legal quality standards for water. Only biological systems can detect the toxic effects of the water constituents. Therefore, the evaluation of toxicity by biological tests is very important when deciding the suitability for safe water discharge or for irrigation applications.
The main purpose of the present work was to assess the potential impacts of waters after been treated for heavy metal removal by hazelnut and almond shells adsorption systems, with short term acute toxicity tests.
To conduct the study, water at pH 6 with 25 mg.L-1 of lead, was treated with 10 g of shell per litre of wastewater, for 24 hours. This procedure was followed for each bark. Afterwards the water was collected for toxicological assays; namely bacterial resistance, seed germination, Lemna minor L. test and plant grow. The effect in isolated bacteria strains was determined by disc diffusion method and the germination index of seed was evaluated using lettuce, with temperature and humidity germination control for 7 days. For aquatic higher organism, Lemnas were used with 4 days contact time with shell solutions, in controlled light and temperature. For terrestrial higher plants, biomass production was evaluated after 14 days of tomato germination had occurred in soil, with controlled humidity, light and temperature.
Toxicity tests of water treated with shells revealed in some extent effects in the tested organisms, with the test assays showing a close behaviour as the control, leading to the conclusion that its further utilization may not be considered to create a serious risk to the environment.
Abstract: In metal cutting industries, mathematical/statistical
models are typically used to predict tool replacement time. These
off-line methods usually result in less than optimum replacement
time thereby either wasting resources or causing quality problems.
The few online real-time methods proposed use indirect measurement
techniques and are prone to similar errors. Our idea is based on
identifying the optimal replacement time using an electronic nose to
detect the airborne compounds released when the tool wear reaches
to a chemical substrate doped into tool material during the
fabrication. The study investigates the feasibility of the idea, possible
doping materials and methods along with data stream mining
techniques for detection and monitoring different phases of tool
wear.
Abstract: Cashew nut shells were converted into activated carbon powders using KOH activation plus CO2 gasification at 1027 K. The increase both of impregnation ratio and activation time, there was swiftly the development of mesoporous structure with increasing of mesopore volume ratio from 20-28% and 27-45% for activated carbon with ratio of KOH per char equal to 1 and 4, respectively. Activated carbon derived from KOH/char ratio equal to 1 and CO2 gasification time from 20 to 150 minutes were exhibited the BET surface area increasing from 222 to 627 m2.g-1. And those were derived from KOH/char ratio of 4 with activation time from 20 to 150 minutes exhibited high BET surface area from 682 to 1026 m2.g-1. The adsorption of Lead(II) and Cadmium(II) ion was investigated. This adsorbent exhibited excellent adsorption for Lead(II) and Cadmium(II) ion. Maximum adsorption presented at 99.61% at pH 6.5 and 98.87% at optimum conditions. The experimental data was calculated from Freundlich isotherm and Langmuir isotherm model. The maximum capacity of Pb2+ and Cd2+ ions was found to be 28.90 m2.g-1 and 14.29 m2.g-1, respectively.
Abstract: Impact is one of very important subjects which always have been considered in mechanical science. Nature of impact is such that which makes its control a hard task. Therefore it is required to present the transfer of impact to other vulnerable part of a structure, when it is necessary, one of the best method of absorbing energy of impact, is by using Thin-walled tubes these tubes collapses under impact and with absorption of energy, it prevents the damage to other parts.Purpose of recent study is to survey the deformation and energy absorption of tubes with different type of cross section (rectangular or square) and with similar volumes, height, mean cross section thickness, and material under loading with different speeds. Lateral loading of tubes are quasi-static type and beside as numerical analysis, also experimental experiences has been performed to evaluate the accuracy of the results. Results from the surveys is indicates that in a same conditions which mentioned above, samples with square cross section ,absorb more energy compare to rectangular cross section, and also by increscent in speed of loading, energy absorption would be more.
Abstract: In the present study, the effect of ferrous sulfate concentration and total solids on bioleaching of heavy metals from sewage sludge has been examined using indigenous iron-oxidizing microorganisms. The experiments on effects of ferrous sulfate concentrations on bioleaching were carried out using ferrous sulfate of different concentrations (5-20 g L-1) to optimize the concentration of ferrous sulfate for maximum bioleaching. A rapid change in the pH and ORP took place in first 2 days followed by a slow change till 16th day in all the sludge samples. A 10 g L-1 ferrous sulfate concentration was found to be sufficient in metal bioleaching in the following order: Zn: 69%>Cu: 52%>Cr: 46%>Ni: 45. Further, bioleaching using 10 g/L ferrous sulfate was found to be efficient up to 20 g L-1 sludge solids concentration. The results of the present study strongly indicate that using 10 g L-1 ferrous sulfate indigenous iron-oxidizing microorganisms can bring down pH to a value needed for significant metal solubilization.
Abstract: Bioleaching of spent catalyst using moderate thermophilic chemolithotrophic acidophiles in growth medium without Fe source was investigated with two different pulp densities and three different size fractions. All the experiments were conducted on shake flasks at a temperature of 65 °C. The leaching yield of Ni and Al was found to be promising with very high leaching yield of 92-96% followed by Al as 41-76%, which means both Ni and Al leaching were favored by the moderate thermophilic bioleaching compared to the mesophilic bioleaching. The acid consumption was comparatively higher for the 10% pulp density experiments. Comparatively minimal difference in the leaching yield with different size fractions and different pulp densities show no requirement of grinding and using low pulp density less than 10%. This process would rather be economical as well as eco-friendly process for future optimization of the recovery of metal values from spent catalyst.