Abstract: In this paper, a Dynamic Economic Dispatch (DED) model is developed for the system consisting of both thermal generators and wind turbines. The inclusion of a significant amount of wind energy into power systems has resulted in additional constraints on DED to accommodate the intermittent nature of the output. The probability of stochastic wind power based on the Weibull probability density function is included in the model as a constraint; A Here-and-Now Approach. The Environmental Protection Agency-s hourly emission target, which gives the maximum emission during the day, is used as a constraint to reduce the atmospheric pollution. A 69-bus test system with non-smooth cost function is used to illustrate the effectiveness of the proposed model compared with static economic dispatch model with including the wind power.
Abstract: Real world Speaker Identification (SI) application
differs from ideal or laboratory conditions causing perturbations that
leads to a mismatch between the training and testing environment
and degrade the performance drastically. Many strategies have been
adopted to cope with acoustical degradation; wavelet based Bayesian
marginal model is one of them. But Bayesian marginal models
cannot model the inter-scale statistical dependencies of different
wavelet scales. Simple nonlinear estimators for wavelet based
denoising assume that the wavelet coefficients in different scales are
independent in nature. However wavelet coefficients have significant
inter-scale dependency. This paper enhances this inter-scale
dependency property by a Circularly Symmetric Probability Density
Function (CS-PDF) related to the family of Spherically Invariant
Random Processes (SIRPs) in Log Gabor Wavelet (LGW) domain
and corresponding joint shrinkage estimator is derived by Maximum
a Posteriori (MAP) estimator. A framework is proposed based on
these to denoise speech signal for automatic speaker identification
problems. The robustness of the proposed framework is tested for
Text Independent Speaker Identification application on 100 speakers
of POLYCOST and 100 speakers of YOHO speech database in three
different noise environments. Experimental results show that the
proposed estimator yields a higher improvement in identification
accuracy compared to other estimators on popular Gaussian Mixture
Model (GMM) based speaker model and Mel-Frequency Cepstral
Coefficient (MFCC) features.
Abstract: Low-density parity-check (LDPC) codes have been shown to deliver capacity approaching performance; however, problematic graphical structures (e.g. trapping sets) in the Tanner graph of some LDPC codes can cause high error floors in bit-error-ratio (BER) performance under conventional sum-product algorithm (SPA). This paper presents a serial concatenation scheme to avoid the trapping sets and to lower the error floors of LDPC code. The outer code in the proposed concatenation is the LDPC, and the inner code is a high rate array code. This approach applies an interactive hybrid process between the BCJR decoding for the array code and the SPA for the LDPC code together with bit-pinning and bit-flipping techniques. Margulis code of size (2640, 1320) has been used for the simulation and it has been shown that the proposed concatenation and decoding scheme can considerably improve the error floor performance with minimal rate loss.
Abstract: Transpedicular screw fixation in spinal fractures,
degenerative changes, or deformities is a well-established procedure.
However, important rate of fixation failure due to screw bending,
loosening, or pullout are still reported particularly in weak bone stock
in osteoporosis. To overcome the problem, mechanism of failure has
to be fully investigated in vitro. Post-mortem human subjects are less
accessible and animal cadavers comprise limitations due to different
geometry and mechanical properties. Therefore, the development of a
synthetic model mimicking the realistic human vertebra is highly
demanded. A bone surrogate, composed of Polyurethane (PU) foam
analogous to cancellous bone porous structure, was tested for 3
different densities in this study. The mechanical properties were
investigated under uniaxial compression test by minimizing the end
artifacts on specimens. The results indicated that PU foam of 0.32
g.cm-3 density has comparable mechanical properties to human
cancellous bone in terms of young-s modulus and yield strength.
Therefore, the obtained information can be considered as primary
step for developing a realistic cancellous bone of human vertebral
body. Further evaluations are also recommended for other density
groups.
Abstract: The aim of this study was to compare the
sensitometric properties of commonly used radiographic films
processed with chemical solutions in different workload hospitals.
The effect of different processing conditions on induced densities on
radiologic films was investigated. Two accessible double emulsions
Fuji and Kodak films were exposed with 11-step wedge and
processed with Champion and CPAC processing solutions. The
mentioned films provided in both workloads centers, high and low.
Our findings displays that the speed and contrast of Kodak filmscreen
in both work load (high and low) is higher than Fuji filmscreen
for both processing solutions. However there was significant
differences in films contrast for both workloads when CPAC solution
had been used (p=0.000 and 0.028). The results showed base plus
fog density for Kodak film was lower than Fuji. Generally Champion
processing solution caused more speed and contrast for investigated
films in different conditions and there was significant differences in
95% confidence level between two used processing solutions
(p=0.01). Low base plus fog density for Kodak films provide more
visibility and accuracy and higher contrast results in using lower
exposure factors to obtain better quality in resulting radiographs. In
this study we found an economic advantages since Champion
solution and Kodak film are used while it makes lower patient dose.
Thus, in a radiologic facility any change in film processor/processing
cycle or chemistry should be carefully investigated before
radiological procedures of patients are acquired.
Abstract: The acidity of different raw Jordanian clays
containing zeolite, bentonite, red and white kaolinite and diatomite
was characterized by means of temperature programmed desorption
(TPD) of ammonia, conversion of 2-methyl-3-butyn-2-ol (MBOH),
FTIR and BET-measurements. FTIR spectra proved presence of
silanol and bridged hydroxyls on the clay surface. The number of
acidic sites was calculated from experimental TPD-profiles. We
observed the decrease of surface acidity correlates with the decrease
of Si/Al ratio except for diatomite. On the TPD-plot for zeolite two
maxima were registered due to different strength of surface acidic
sites. Values of MBOH conversion, product yields and selectivity
were calculated for the catalysis on Jordanian clays. We obtained that
all clay samples are able to convert MBOH into a major product
which is 3-methyl-3-buten-1-yne (MBYNE) catalyzed by acid
surface sites with the selectivity close to 70%. There was found a
correlation between MBOH conversion and acidity of clays
determined by TPD-NH3, i.e. the higher the acidity the higher the
conversion of MBOH. However, diatomite provided the lowest
conversion of MBOH as result of poor polarization of silanol groups.
Comparison of surface areas and conversions revealed the highest
density of active sites for red kaolinite and the lowest for zeolite and
diatomite.
Abstract: Sediment and mangrove root samples from Iko River
Estuary, Nigeria were analyzed for microbial and polycyclic
aromatic hydrocarbon (PAH) content. The total heterotrophic
bacterial (THB) count ranged from 1.1x107 to 5.1 x107 cfu/g, total
fungal (TF) count ranged from 1.0x106 to 2.7x106 cfu/g, total
coliform (TC) count ranged from 2.0x104 to 8.0x104cfu/g while
hydrocarbon utilizing bacterial (HUB) count ranged from 1.0x 105 to
5.0 x 105cfu/g. There was a range of positive correlation (r = 0.72 to
0.93) between THB count and total HUB count, respectively. The
organisms were Staphylococcus aureus, Bacillus cereus,
Flavobacterium breve, Pseudomonas aeruginosa, Erwinia
amylovora, Escherichia coli, Enterobacter sp, Desulfovibrio sp,
Acinetobacter iwoffii, Chromobacterium violaceum, Micrococcus
sedentarius, Corynebacterium sp, and Pseudomonas putrefaciens.
The PAH were Naphthalene, 2-Methylnaphthalene, Acenapthylene,
Acenaphthene, Fluorene, Phenanthene, Anthracene, Fluoranthene,
Pyrene, Benzo(a)anthracene, Chrysene, Benzo(b)fluoranthene,
Benzo(k)fluoranthene, Benzo(a)pyrene, Dibenzo(a,h)anthracene,
Benzo(g,h,l)perylene ,Indeno(1,2,3-d)pyrene with individual PAH
concentrations that ranged from 0.20mg/kg to 1.02mg/kg, 0.20mg/kg
to 1.07mg/kg and 0.2mg/kg to 4.43mg/kg in the benthic sediment,
epipellic sediment and mangrove roots, respectively. Total PAH
ranged from 6.30 to 9.93mg/kg, 6.30 to 9.13mg/kg and 9.66 to
16.68mg/kg in the benthic sediment, epipellic sediment and
mangrove roots, respectively. The high concentrations in the
mangrove roots are indicative of bioaccumulation of the pollutant in
the plant tissue. The microorganisms are of ecological significance
and the detectable quantities of polycyclic aromatic hydrocarbon
could be partitioned and accumulated in tissues of infaunal and
epifaunal organisms in the study area.
Abstract: Experimental investigations were made on the instability of supercritical kerosene flowing in active cooling channels. Two approaches were used to control the pressure in the channel. One is the back-pressure valve while the other is the venturi. In both conditions, a kind of low-frequency oscillation of pressure and temperature is observed. And the oscillation periods are calculated. By comparison with the flow time, it is concluded that the instability occurred in active cooling channels is probably one kind of density wave instability. And its period has no relationship with the cooling channel geometry, nor the pressure, but only depends on the flow time of kerosene in active cooling channels. When the mass flow rate, density and pressure drop couple with each other, the density wave instability will appear.
Abstract: In the last 15 years, a number of methods have been proposed for forecasting based on fuzzy time series. Most of the fuzzy time series methods are presented for forecasting of enrollments at the University of Alabama. However, the forecasting accuracy rates of the existing methods are not good enough. In this paper, we compared our proposed new method of fuzzy time series forecasting with existing methods. Our method is based on frequency density based partitioning of the historical enrollment data. The proposed method belongs to the kth order and time-variant methods. The proposed method can get the best forecasting accuracy rate for forecasting enrollments than the existing methods.
Abstract: Porcelain specimens were fired at 6C/min to 1250C (dwell time 0.5-3h) and cooled at 6C/min to room temperature. Additionally, three different slower firing/cooling cycles were tried. Sintering profile and effects on MOR, crystalline phase content and morphology were investigated using dilatometry, 4-point bending strength, XRD and FEG-SEM respectively. Industrial-sized specimens prepared using the promising cycle were tested basing on the ANSI standards. Increasing dwell time from 1h to 3h at peak temperature of 1250C resulted in neither a significant effect on the quartz and mullite content nor MOR. Reducing the firing/cooling rate to below 6C/min, for peak temperature of 1250C (dwell time of 1h) does not result in improvement of strength of porcelain. The industrial sized specimen exhibited flashover voltages of 20.3kV (dry) and 9.3kV (wet) respectively, transverse strength of 12.5kN and bulk density of 2.27g/cm3, which are satisfactory. There was however dye penetration during porosity test. KeywordsDwell time, Microstructure, Porcelain, Strength.
Abstract: We fabricated the inverted-staggered etch stopper
structure oxide-based TFT and investigated the characteristics of oxide
TFT under the 400 nm wavelength light illumination. When 400 nm
light was illuminated, the threshold voltage (Vth) decreased and
subthreshold slope (SS) increased at forward sweep, while Vth and SS
were not altered when larger wavelength lights, such as 650 nm, 550
nm and 450 nm, were illuminated. At reverse sweep, the transfer curve
barely changed even under 400 nm light. Our experimental results
support that photo-induced hole carriers are captured by donor-like
interface trap and it caused the decrease of Vth and increase of SS. We
investigated the interface trap density increases proportionally to the
photo-induced hole concentration at active layer.
Abstract: This paper presents a supervised clustering algorithm,
namely Grid-Based Supervised Clustering (GBSC), which is able to
identify clusters of any shapes and sizes without presuming any
canonical form for data distribution. The GBSC needs no prespecified
number of clusters, is insensitive to the order of the input
data objects, and is capable of handling outliers. Built on the
combination of grid-based clustering and density-based clustering,
under the assistance of the downward closure property of density
used in bottom-up subspace clustering, the GBSC can notably reduce
its search space to avoid the memory confinement situation during its
execution. On two-dimension synthetic datasets, the GBSC can
identify clusters with different shapes and sizes correctly. The GBSC
also outperforms other five supervised clustering algorithms when
the experiments are performed on some UCI datasets.
Abstract: Following the laser ablation studies leading to a
theory of nuclei confinement by a Debye layer mechanism, we
present here numerical evaluations for the known stable nuclei where
the Coulomb repulsion is included as a rather minor component
especially for lager nuclei. In this research paper the required
physical conditions for the formation and stability of nuclei
particularly endothermic nuclei with mass number greater than to
which is an open astrophysical question have been investigated.
Using the Debye layer mechanism, nuclear surface energy, Fermi
energy and coulomb repulsion energy it is possible to find conditions
under which the process of nucleation is permitted in early universe.
Our numerical calculations indicate that about 200 second after the
big bang at temperature of about 100 KeV and subrelativistic region
with nucleon density nearly equal to normal nuclear density namely,
10cm all endothermic and exothermic nuclei have been
formed.
Abstract: This paper studies the application of a variety of
sawdust materials in the production of lightweight insulating bricks.
First, the mineralogical and chemical composition of clays was determined. Next, ceramic bricks were fabricated with different
quantities of materials (3–6 and 9 wt. % for sawdust, 65 wt. % for grey clay, 24–27 and 30 wt. % for yellow clay and 2 wt% of tuff).
These bricks were fired at 800 and 950 °C. The effect of adding this sawdust on the technological behaviour of the brick was assessed by
drying and firing shrinkage, water absorption, porosity, bulk density
and compressive strength. The results have shown that the optimum
sintering temperature is 950 °C. Below this temperature, at 950 °C,
increased open porosity was observed, which decreased the compressive strength of the bricks. Based on the results obtained, the
optimum amounts of waste were 9 wt. % sawdust of eucalyptus, 24 wt. % shaping moisture and 1.6 particle size diameter. These percentages produced bricks whose mechanical properties were
suitable for use as secondary raw materials in ceramic brick
production.
Abstract: An inflation–extension test with human vena cava
inferior was performed with the aim to fit a material model. The vein
was modeled as a thick–walled tube loaded by internal pressure and
axial force. The material was assumed to be an incompressible
hyperelastic fiber reinforced continuum. Fibers are supposed to be
arranged in two families of anti–symmetric helices. Considered
anisotropy corresponds to local orthotropy. Used strain energy
density function was based on a concept of limiting strain
extensibility. The pressurization was comprised by four pre–cycles
under physiological venous loading (0 – 4kPa) and four cycles under
nonphysiological loading (0 – 21kPa). Each overloading cycle was
performed with different value of axial weight. Overloading data
were used in regression analysis to fit material model. Considered
model did not fit experimental data so good. Especially predictions
of axial force failed. It was hypothesized that due to
nonphysiological values of loading pressure and different values of
axial weight the material was not preconditioned enough and some
damage occurred inside the wall. A limiting fiber extensibility
parameter Jm was assumed to be in relation to supposed damage.
Each of overloading cycles was fitted separately with different values
of Jm. Other parameters were held the same. This approach turned out
to be successful. Variable value of Jm can describe changes in the
axial force – axial stretch response and satisfy pressure – radius
dependence simultaneously.
Abstract: To study the performance of soybean (Glycine max L.) cultivars in varying weeding regimes, a field experiment was conducted in 2010. The experiment was split plot in a randomized complete block design with 3 replicates. The four cultivars and two lines of soybean including: Sahar, Hill, Sari, Telar, 032 and 033 in main plot and weeding regime consist of no weeding (control), one weeding (35 days after planting) and two weeding (35+20 days after planting) were randomized in sub plot. In weed infested plots inevitably had the highest yield reduction in all varieties. On the other hand, plots weeded twice showed the best performance for all cultivars and lines. Although 033 had the highest yield over weeding regimes, but Hill was the best cultivar in suppression of weeds, which indicated the competitiveness of this cultivar. Double weeding, with the use of competitive soybean cultivars would be an effective approach for producing yield.
Abstract: Alumina matrix composites with addition of hexagonal boron nitride (hBN), acting as solid lubricant, were produced. Main purpose of solid lubricants is to dispose the necessity of using cooling lubricants in machining process. Hot pressing was used as a consolidating process for Al2O3-x%wt.hBN (x=1/ 2,5/ 5 /7,5 /10) composites. Properties of sinters such as relative density, hardness, Young-s modulus and fracture toughness were examined. Obtained samples characterize by high relative density. Hardness and fracture toughness values allow the use of alumina – hBN composites for machining steels even in hardened condition. However it was observed that high weight content of hBN can negatively influence the mechanical properties of composites.
Abstract: In this paper, an erosion-based model for abrasive
waterjet (AWJ) turning process is presented. By using modified
Hashish erosion model, the volume of material removed by impacting
of abrasive particles to surface of the rotating cylindrical specimen is
estimated and radius reduction at each rotation is calculated.
Different to previous works, the proposed model considers the
continuous change in local impact angle due to change in workpiece
diameter, axial traverse rate of the jet, the abrasive particle roundness
and density. The accuracy of the proposed model is examined by
experimental tests under various traverse rates. The final diameters
estimated by the proposed model are in good accordance with
experiments.
Abstract: The purpose of this article is to study the effects of
plants cover on overland flow and, therefore, its influences on the
amount of eroded and transported soil. In this investigation, all the
experiments were conducted in the LEGHYD laboratory using a
rainfall simulator and a soil tray. The experiments were conducted
using an experimental plot (soil tray) which is 2m long, 0.5 m wide
and 0.15 m deep. The soil used is an agricultural sandy soil (62,08%
coarse sand, 19,14% fine sand, 11,57% silt and 7,21% clay). Plastic
rods (4 mm in diameter) were used to simulate the plants at different
densities: 0 stem/m2 (bared soil), 126 stems/m², 203 stems/m², 461
stems/m² and 2500 stems/m²). The used rainfall intensity is 73mm/h
and the soil tray slope is fixed to 3°. The results have shown that the
overland flow velocities decreased with increasing stems density, and
the density cover has a great effect on sediment concentration.
Darcy–Weisbach and Manning friction coefficients of overland flow
increased when the stems density increased. Froude and Reynolds
numbers decreased with increasing stems density and, consequently,
the flow regime of all treatments was laminar and subcritical. From
these findings, we conclude that increasing the plants cover can
efficiently reduce soil loss and avoid denuding the roots plants.
Abstract: Organ motion, especially respiratory motion, is a technical challenge to radiation therapy planning and dosimetry. This motion induces displacements and deformation of the organ tissues within the irradiated region which need to be taken into account when simulating dose distribution during treatment. Finite element modeling (FEM) can provide a great insight into the mechanical behavior of the organs, since they are based on the biomechanical material properties, complex geometry of organs, and anatomical boundary conditions. In this paper we present an original approach that offers the possibility to combine image-based biomechanical models with particle transport simulations. We propose a new method to map material density information issued from CT images to deformable tetrahedral meshes. Based on the principle of mass conservation our method can correlate density variation of organ tissues with geometrical deformations during the different phases of the respiratory cycle. The first results are particularly encouraging, as local error quantification of density mapping on organ geometry and density variation with organ motion are performed to evaluate and validate our approach.