Abstract: We have studied the migration of a charged permeable aggregate in electrolyte under the influence of an axial electric field and pressure gradient. The migration of the positively charged aggregate leads to a deformation of the anionic cloud around it. The hydrodynamics of the aggregate is governed by the interaction of electroosmotic flow in and around the particle, hydrodynamic friction and electric force experienced by the aggregate. We have computed the non-linear Nernest-Planck equations coupled with the Dracy- Brinkman extended Navier-Stokes equations and Poisson equation for electric field through a finite volume method. The permeability of the aggregate enable the counterion penetration. The penetration of counterions depends on the volume charge density of the aggregate and ionic concentration of electrolytes at a fixed field strength. The retardation effect due to the double layer polarization increases the drag force compared to an uncharged aggregate. Increase in migration sped from the electrophretic velocity of the aggregate produces further asymmetry in charge cloud and reduces the electric body force exerted on the particle. The permeability of the particle have relatively little influence on the electric body force when Double layer is relatively thin. The impact of the key parameters of electrokinetics on the hydrodynamics of the aggregate is analyzed.
Abstract: This paper presents a synthetic jet air blower actuated
by PZT for air blowing for air-breathing micro PEM fuel cell. The
several factors to affect the performance of air-breathing PEM fuel cell
such as air flow rate, opening ratio and cathode open type in the
cathode side were studied. Especially, an air flow rate is critical
condition to improve its performance. In this paper, we developed a
synthetic jet air blower to supply a high stoichiometric air flow. The
synthetic jet mechanism is a zero mass flux device that converts
electrical energy into the momentum. The synthetic jet actuation is
usually generated by a traditional PZT actuator, which consists of a
small cylindrical cavity, in/outlet channel and PZT diaphragms. The
flow rate of the fabricated synthetic jet air blower was 400cc/min at
550Hz and its power consumption was very low under 0.3W. The
proposed air-breathing PEM fuel cell which installed synthetic jet air
blower was higher performance and stability during continuous
operation than the air-breathing fuel cell without auxiliary device to
supply the air. The results showed that the maximum power density
was 188mW/cm2 at 400mA/cm2. This maximum power density and
durability were improved more than 40% and 20%, respectively.
Abstract: The objective of this work was to investigate flow
properties of powdered infant formula samples. Samples were
purchased at a local pharmacy and differed in composition. Lactose
free infant formula, gluten free infant formula and infant formulas
containing dietary fibers and probiotics were tested and compared
with a regular infant formula sample which did not contain any of
these supplements. Particle size and bulk density were determined
and their influence on flow properties was discussed. There were no
significant differences in bulk densities of the samples, therefore the
connection between flow properties and bulk density could not be
determined. Lactose free infant formula showed flow properties
different to standard supplement-free sample. Gluten free infant
formula with addition of probiotic microorganisms and dietary fiber
had the narrowest particle size distribution range and exhibited the
best flow properties. All the other samples exhibited the same
tendency of decreasing compaction coefficient with increasing flow
speed, which means they all become freer flowing with higher flow
speeds.
Abstract: Many real-world data sets consist of a very high dimensional feature space. Most clustering techniques use the distance or similarity between objects as a measure to build clusters. But in high dimensional spaces, distances between points become relatively uniform. In such cases, density based approaches may give better results. Subspace Clustering algorithms automatically identify lower dimensional subspaces of the higher dimensional feature space in which clusters exist. In this paper, we propose a new clustering algorithm, ISC – Intelligent Subspace Clustering, which tries to overcome three major limitations of the existing state-of-art techniques. ISC determines the input parameter such as є – distance at various levels of Subspace Clustering which helps in finding meaningful clusters. The uniform parameters approach is not suitable for different kind of databases. ISC implements dynamic and adaptive determination of Meaningful clustering parameters based on hierarchical filtering approach. Third and most important feature of ISC is the ability of incremental learning and dynamic inclusion and exclusions of subspaces which lead to better cluster formation.
Abstract: In this paper, the melting of a semi-infinite body as a
result of a moving laser beam has been studied. Because the Fourier
heat transfer equation at short times and large dimensions does not
have sufficient accuracy; a non-Fourier form of heat transfer
equation has been used. Due to the fact that the beam is moving in x
direction, the temperature distribution and the melting pool shape are
not asymmetric. As a result, the problem is a transient threedimensional
problem. Therefore, thermophysical properties such as
heat conductivity coefficient, density and heat capacity are functions
of temperature and material states. The enthalpy technique, used for
the solution of phase change problems, has been used in an explicit
finite volume form for the hyperbolic heat transfer equation. This
technique has been used to calculate the transient temperature
distribution in the semi-infinite body and the growth rate of the melt
pool. In order to validate the numerical results, comparisons were
made with experimental data. Finally, the results of this paper were
compared with similar problem that has used the Fourier theory. The
comparison shows the influence of infinite speed of heat propagation
in Fourier theory on the temperature distribution and the melt pool
size.
Abstract: As the material used for fuselage structure must
possess low density, high strength to weight ratio, the selection of
appropriate materials for fuselage structure is one of the most
important tasks. Aluminum metal itself is soft and low in strength. It
can be made stronger by giving proper combination of suitable alloy
addition, mechanical treatment and thermal treatment. The usual
thermal treatment given to aluminum alloys is called age-hardening
or precipitation hardening. In this paper, the studies are carried out on
7075 aluminum alloy which is how to improve strength level for
fuselage structure. The marked effect of the strength on the ternary
alloy is clearly demonstrated at several ageing times and
temperatures. It is concluded that aluminum-zinc-magnesium alloy
can get the highest strength level in natural ageing.
Abstract: This study presents an investigation of
electrochemical variables and an application of the optimal
parameters in operating a continuous upflow electrocoagulation
reactor in removing dye. Direct red 23, which is azo-based, was used
as a representative of direct dyes. First, a batch mode was employed
to optimize the design parameters: electrode type, electrode distance,
current density and electrocoagulation time. The optimal parameters
were found to be iron anode, distance between electrodes of 8 mm
and current density of 30 A·m-2 with contact time of 5 min. The
performance of the continuous upflow reactor with these parameters
was satisfactory, with >95% color removal and energy consumption
in the order of 0.6-0.7 kWh·m-3.
Abstract: Evolution of one-dimensional electron system under
high-energy-density (HED) conditions is investigated, using the
principle of least-action and variational method. In a single-mode
modulation model, the amplitude and spatial wavelength of the
modulation are chosen to be general coordinates. Equations of motion
are derived by considering energy conservation and force balance.
Numerical results show that under HED conditions, electron density
modulation could exist. Time dependences of amplitude and
wavelength are both positively related to the rate of energy input.
Besides, initial loading speed has a significant effect on modulation
amplitude, while wavelength relies more on loading duration.
Abstract: Nonspecific protein adsorption generally occurs on
any solid surfaces and usually has adverse consequences. Adsorption
of proteins onto a solid surface is believed to be the initial and
controlling step in biofouling. Surfaces modified with end-tethered
poly(ethylene glycol) (PEG) have been shown to be protein-resistant
to some degree. In this study, the adsorption of β-casein and
lysozyme was performed on 6 different types of surfaces where PEG
was tethered onto stainless steel by polyethylene imine (PEI) through
either OH or NHS end groups. Protein adsorption was also performed
on the bare stainless steel surface as a control. The adsorption was
conducted at 23 °C and pH 7.2. In situ QCM-D was used to
determine PEG adsorption kinetics, plateau PEG chain densities,
protein adsorption kinetics and plateau protein adsorbed quantities.
PEG grafting density was the highest for a NHS coupled chain,
around 0.5 chains / nm2. Interestingly, lysozyme which has smaller
size than β-casein, appeared to adsorb much less mass than that of β-
casein. Overall, the surface with high PEG grafting density exhibited
a good protein rejection.
Abstract: This paper presents a new method for estimating the nonstationary
noise power spectral density given a noisy signal. The
method is based on averaging the noisy speech power spectrum using
time and frequency dependent smoothing factors. These factors are
adjusted based on signal-presence probability in individual frequency
bins. Signal presence is determined by computing the ratio of the
noisy speech power spectrum to its local minimum, which is updated
continuously by averaging past values of the noisy speech power
spectra with a look-ahead factor. This method adapts very quickly to
highly non-stationary noise environments. The proposed method
achieves significant improvements over a system that uses voice
activity detector (VAD) in noise estimation.
Abstract: In aircraft applications, according to the nature of
electrical equipment its location may be in unpressurized area or very
close to the engine; thus, the environmental conditions may change
from atmospheric pressure to less than 100 mbar, and the temperature
may be higher than the ambient one as in most real working
conditions of electrical equipment. Then, the classical Paschen curve
has to be replotted since these parameters may affect the discharge
ignition voltage. In this paper, we firstly investigate the domain of
validity of two corrective expressions on the Paschen-s law found in
the literature, in case of changing the air environment and known as
Peek and Dunbar corrections. Results show that these corrections are
no longer valid for combined variation of temperature and pressure.
After that, a new empirical expression for breakdown voltage is
proposed and is validated in the case of combined variations of
temperature and pressure.
Abstract: The potential of entomopathogenic nematodes in suppressing T. squalida population on cauliflower from transplanting to harvest was evaluated. Significant reductions in plant infestation percentage and population density (/m2) were recorded throughout the plantation seasons, 2011 and 2012 before and after spraying the plants. The percent reduction in numbers/m2 was the highest in March for the treatments with Heterorhabditis indica Behera and Heterorhabditis bacteriophora Giza during the plantation season 2011, while at the plantation season 2012, the reduction in population density was the highest in January for Heterorhabditis Indica Behera and in February for H . bacteriophora Giza treatments. In a comparison test with conventional insecticides Hostathion and Lannate, there were no significant differences in control measures resulting from treatments with H. indica Behera, H. bacteriophora Giza and Lannate. At the plantation season is 2012. Also, the treatments reduced the economic threshold of T. squalida on cauliflower in this experiment as compared with before and after spraying with both the two entomopathogenic nematodes at both seasons 2011 and 2012. This means an increase in the marketability of heads harvested as a consequence of monthly treatments.
Abstract: A simple approach is demonstrated for growing large
scale, nearly vertically aligned ZnO nanowire arrays by thermal
oxidation method. To reveal effect of temperature on growth and
physical properties of the ZnO nanowires, gold coated zinc substrates
were annealed at 300 °C and 400 °C for 4 hours duration in air. Xray
diffraction patterns of annealed samples indicated a set of well
defined diffraction peaks, indexed to the wurtzite hexagonal phase of
ZnO. The scanning electron microscopy studies show formation of
ZnO nanowires having length of several microns and average of
diameter less than 500 nm. It is found that the areal density of wires
is relatively higher, when the annealing is carried out at higher
temperature i.e. at 400°C. From the field emission studies, the values
of the turn-on and threshold field, required to draw emission current
density of 10 μA/cm2 and 100 μA/cm2 are observed to be 1.2 V/μm
and 1.7 V/μm for the samples annealed at 300 °C and 2.9 V/μm and
3.7 V/μm for that annealed at 400 °C, respectively. The field
emission current stability, investigated over duration of more than 2
hours at the preset value of 1 μA, is found to be fairly good in both
cases. The simplicity of the synthesis route coupled with the
promising field emission properties offer unprecedented advantage
for the use of ZnO field emitters for high current density
applications.
Abstract: We report here, the results of molecular dynamics
simulation of p-doped (Ga-face)GaN over n-doped (Siface)(
0001)4H-SiC hetero-epitaxial material system with one-layer
each of Ga-flux and (Al-face)AlN, as the interface materials, in the
form of, the total Density of States (DOS). It is found that the total
DOS at the Fermi-level for the heavily p-doped (Ga-face)GaN and ndoped
(Si-face)4H-SiC hetero-epitaxial system, with one layer of
(Al-face)AlN as the interface material, is comparatively higher than
that of the various cases studied, indicating that there could be good
vertical conduction across the (Ga-face)GaN over (Si-face)(0001)4HSiC
hetero-epitaxial material system.
Abstract: This paper presents a novel method for prediction of
the mechanical behavior of proximal femur using the general
framework of the quantitative computed tomography (QCT)-based
finite element Analysis (FEA). A systematic imaging and modeling
procedure was developed for reliable correspondence between the
QCT-based FEA and the in-vitro mechanical testing. A speciallydesigned
holding frame was used to define and maintain a unique
geometrical reference system during the analysis and testing. The
QCT images were directly converted into voxel-based 3D finite
element models for linear and nonlinear analyses. The equivalent
plastic strain and the strain energy density measures were used to
identify the critical elements and predict the failure patterns. The
samples were destructively tested using a specially-designed gripping
fixture (with five degrees of freedom) mounted within a universal
mechanical testing machine. Very good agreements were found
between the experimental and the predicted failure patterns and the
associated load levels.
Abstract: The paper investigates parallel channel instabilities of
natural circulation boiling water reactor. A thermal-hydraulic model
is developed to simulate two-phase flow behavior in the natural circulation boiling water reactor (NCBWR) with the incorporation of
ex-core components and recirculation loop such as steam separator, down-comer, lower-horizontal section and upper-horizontal section
and then, numerical analysis is carried out for parallel channel
instabilities of the reactor undergoing both in-phase and out-of-phase
modes of oscillations. To analyze the relative effect on stability of the reactor due to inclusion of various ex-core components and
recirculation loop, marginal stable point is obtained at a particular inlet enthalpy of the reactor core without the inclusion of ex-core
components and recirculation loop and then with the inclusion of the
same. Numerical simulations are also conducted to determine the
relative dominance between two modes of oscillations i.e. in-phase and out-of-phase. Simulations are also carried out when the channels
are subjected to asymmetric power distribution keeping the inlet enthalpy same.
Abstract: Attempt was made to improve certain characteristics of bio-oil derived from palm kernel pyrolysis by blending it with diesel fuel and alcohols. Two types of alcohol, ethanol or butanol, was used as cosolvent to stabilize the phase of ternary systems. Phase behaviors and basic fuel properties of palm kernel bio-oildiesel- alcohol systems were investigated in this study. Alcohol types showed a significant influence on the phase characteristics with palm kernel bio-oil-diesel-butanol system giving larger soluble area than that of palm kernel bio-oil-diesel-ethanol system. For fuel properties, blended fuels showed superior properties including lower values of density (~860 kg/m3 at 25°C), viscosity (~4.12 mm2/s at 40°C), carbon residue (1.02-2.53 wt%), ash (0.018-0.034 wt%) and pour point (
Abstract: In a field experiment, growth parameters of soybean
cultivars in different weeding regimes was investigated. The trial was
split plot in a randomized complete block design. The four cultivars
and two lines of soybean (Glycine max L.) including: Sahar, Hill,
Sari, Telar, 032 and 033 in main plot and weeding regime consist of
no weeding (control), one weeding (35 days after planting) and two
weeding (35+20 days after planting) were randomized in sub plot.
The results showed that during the growth season 033 had the highest
dry matter in two weeding. In two weeding regime the dry matter
decreased. ). In all weeding regimes 033 had the highest CGR (Figs.
3a, 3b and 3c), which cleared this cultivar ability compare to the
others. This cultivar by increasing its leaf area could do more
photosynthesis, so, have a higher CGR.
Abstract: Studies on gas solid mass transfer using Supercritical fluid CO2 (SC-CO2) in a packed bed of palm kernels was investigated at operating conditions of temperature 50 °C and 70 °C and pressures ranges from 27.6 MPa, 34.5 MPa, 41.4 MPa and 48.3 MPa. The development of mass transfer models requires knowledge of three properties: the diffusion coefficient of the solute, the viscosity and density of the Supercritical fluids (SCF). Matematical model with respect to the dimensionless number of Sherwood (Sh), Schmidt (Sc) and Reynolds (Re) was developed. It was found that the model developed was found to be in good agreement with the experimental data within the system studied.
Abstract: The flow field within the combustor of scramjet
engine is very complex and poses a considerable challenge in the
design and development of a supersonic combustor with an optimized
geometry. In this paper comprehensive numerical studies on flow
field characteristics of different cavity based scramjet combustors
with transverse injection of hydrogen have been carried out for both
non-reacting and reacting flows. The numerical studies have been
carried out using a validated 2D unsteady, density based 1st-order
implicit k-omega turbulence model with multi-component finite rate
reacting species. The results show a wide variety of flow features
resulting from the interactions between the injector flows, shock
waves, boundary layers, and cavity flows. We conjectured that an
optimized cavity is a good choice to stabilize the flame in the
hypersonic flow, and it generates a recirculation zone in the scramjet
combustor. We comprehended that the cavity based scramjet
combustors having a bearing on the source of disturbance for the
transverse jet oscillation, fuel/air mixing enhancement, and flameholding
improvement. We concluded that cavity shape with
backward facing step and 45o forward ramp is a good choice to get
higher temperatures at the exit compared to other four models of
scramjet combustors considered in this study.