Abstract: Intrusion Detection System is significant in network
security. It detects and identifies intrusion behavior or intrusion
attempts in a computer system by monitoring and analyzing the
network packets in real time. In the recent year, intelligent algorithms
applied in the intrusion detection system (IDS) have been an
increasing concern with the rapid growth of the network security.
IDS data deals with a huge amount of data which contains irrelevant
and redundant features causing slow training and testing process,
higher resource consumption as well as poor detection rate. Since the
amount of audit data that an IDS needs to examine is very large even
for a small network, classification by hand is impossible. Hence, the
primary objective of this review is to review the techniques prior to
classification process suit to IDS data.
Abstract: Robot manipulators are highly coupled nonlinear
systems, therefore real system and mathematical model of dynamics
used for control system design are not same. Hence, fine-tuning of
controller is always needed. For better tuning fast simulation speed
is desired. Since, Matlab incorporates LAPACK to increase the speed
and complexity of matrix computation, dynamics, forward and
inverse kinematics of PUMA 560 is modeled on Matlab/Simulink in
such a way that all operations are matrix based which give very less
simulation time. This paper compares PID parameter tuning using
Genetic Algorithm, Simulated Annealing, Generalized Pattern Search
(GPS) and Hybrid Search techniques. Controller performances for all
these methods are compared in terms of joint space ITSE and
cartesian space ISE for tracking circular and butterfly trajectories.
Disturbance signal is added to check robustness of controller. GAGPS
hybrid search technique is showing best results for tuning PID
controller parameters in terms of ITSE and robustness.
Abstract: Data security in u-Health system can be an important
issue because wireless network is vulnerable to hacking. However, it is
not easy to implement a proper security algorithm in an embedded
u-health monitoring because of hardware constraints such as low
performance, power consumption and limited memory size and etc. To
secure data that contain personal and biosignal information, we
implemented several security algorithms such as Blowfish, data
encryption standard (DES), advanced encryption standard (AES) and
Rivest Cipher 4 (RC4) for our u-Health monitoring system and the
results were successful. Under the same experimental conditions, we
compared these algorithms. RC4 had the fastest execution time.
Memory usage was the most efficient for DES. However, considering
performance and safety capability, however, we concluded that AES
was the most appropriate algorithm for a personal u-Health monitoring
system.
Abstract: Modeling of the distributed systems allows us to
represent the whole its functionality. The working system instance
rarely fulfils the whole functionality represented by model; usually
some parts of this functionality should be accessible periodically.
The reporting system based on the Data Warehouse concept seams to
be an intuitive example of the system that some of its functionality is
required only from time to time. Analyzing an enterprise risk
associated with the periodical change of the system functionality, we
should consider not only the inaccessibility of the components
(object) but also their functions (methods), and the impact of such a
situation on the system functionality from the business point of view.
In the paper we suggest that the risk attributes should be estimated
from risk attributes specified at the requirements level (Use Case in
the UML model) on the base of the information about the structure of
the model (presented at other levels of the UML model). We argue
that it is desirable to consider the influence of periodical changes in
requirements on the enterprise risk estimation. Finally, the
proposition of such a solution basing on the UML system model is
presented.
Abstract: The equilibrium chemical reactions taken place in a converter reactor of the Khorasan Petrochemical Ammonia plant was studied using the minimization of Gibbs free energy method. In the minimization of the Gibbs free energy function the Davidon– Fletcher–Powell (DFP) optimization procedure using the penalty terms in the well-defined objective function was used. It should be noted that in the DFP procedure along with the corresponding penalty terms the Hessian matrices for the composition of constituents in the Converter reactor can be excluded. This, in fact, can be considered as the main advantage of the DFP optimization procedure. Also the effect of temperature and pressure on the equilibrium composition of the constituents was investigated. The results obtained in this work were compared with the data collected from the converter reactor of the Khorasan Petrochemical Ammonia plant. It was concluded that the results obtained from the method used in this work are in good agreement with the industrial data. Notably, the algorithm developed in this work, in spite of its simplicity, takes the advantage of short computation and convergence time.
Abstract: This paper presents a remote on-line diagnostic system
for vehicles via the use of On-Board Diagnostic (OBD), GPS, and 3G
techniques. The main parts of the proposed system are on-board
computer, vehicle monitor server, and vehicle status browser. First,
the on-board computer can obtain the location of deriver and vehicle
status from GPS receiver and OBD interface, respectively. Then
on-board computer will connect with the vehicle monitor server
through 3G network to transmit the real time vehicle system status.
Finally, vehicle status browser could show the remote vehicle status
including vehicle speed, engine rpm, battery voltage, engine coolant
temperature, and diagnostic trouble codes. According to the
experimental results, the proposed system can help fleet managers and
car knockers to understand the remote vehicle status. Therefore this
system can decrease the time of fleet management and vehicle repair
due to the fleet managers and car knockers who find the diagnostic
trouble messages in time.
Abstract: Forecasting the values of the indicators, which
characterize the effectiveness of performance of organizations is of
great importance for their successful development. Such forecasting
is necessary in order to assess the current state and to foresee future
developments, so that measures to improve the organization-s
activity could be undertaken in time. The article presents an
overview of the applied mathematical and statistical methods for
developing forecasts. Special attention is paid to artificial neural
networks as a forecasting tool. Their strengths and weaknesses are
analyzed and a synopsis is made of the application of artificial neural
networks in the field of forecasting of the values of different
education efficiency indicators. A method of evaluation of the
activity of universities using the Balanced Scorecard is proposed and
Key Performance Indicators for assessment of e-learning are
selected. Resulting indicators for the evaluation of efficiency of the
activity are proposed. An artificial neural network is constructed and
applied in the forecasting of the values of indicators for e-learning
efficiency on the basis of the KPI values.
Abstract: This paper aims at to develop a robust optimization methodology for the mechatronic modules of machine tools by considering all important characteristics from all structural and control domains in one single process. The relationship between these two domains is strongly coupled. In order to reduce the disturbance caused by parameters in either one, the mechanical and controller design domains need to be integrated. Therefore, the concurrent integrated design method Design For Control (DFC), will be employed in this paper. In this connect, it is not only applied to achieve minimal power consumption but also enhance structural performance and system response at same time. To investigate the method for integrated optimization, a mechatronic feed drive system of the machine tools is used as a design platform. Pro/Engineer and AnSys are first used to build the 3D model to analyze and design structure parameters such as elastic deformation, nature frequency and component size, based on their effects and sensitivities to the structure. In addition, the robust controller,based on Quantitative Feedback Theory (QFT), will be applied to determine proper control parameters for the controller. Therefore, overall physical properties of the machine tool will be obtained in the initial stage. Finally, the technology of design for control will be carried out to modify the structural and control parameters to achieve overall system performance. Hence, the corresponding productivity is expected to be greatly improved.
Abstract: This paper considers a scheduling problem in flexible
flow shops environment with the aim of minimizing two important
criteria including makespan and cumulative tardiness of jobs. Since
the proposed problem is known as an Np-hard problem in literature,
we have to develop a meta-heuristic to solve it. We considered
general structure of Genetic Algorithm (GA) and developed a new
version of that based on Data Envelopment Analysis (DEA). Two
objective functions assumed as two different inputs for each Decision
Making Unit (DMU). In this paper we focused on efficiency score of
DMUs and efficient frontier concept in DEA technique. After
introducing the method we defined two different scenarios with
considering two types of mutation operator. Also we provided an
experimental design with some computational results to show the
performance of algorithm. The results show that the algorithm
implements in a reasonable time.
Abstract: A Laboratory-scale packed bed reactor with microbial
cellulose as the biofilm carrier was used to investigate the
denitrification of high-strength nitrate wastewater with specific
emphasis on the effect the nitrogen loading rate and hydraulic
retention time. Ethanol was added as a carbon source for
denitrification. As a result of this investigation, it was found that up
to 500 mg/l feed nitrate concentration the present system is able to
produce an effluent with nitrate content below 10 ppm at 3 h
hydraulic retention time. The highest observed denitrification rate
was 4.57 kg NO3-N/ (m3 .d) at a nitrate load of 5.64 kg NO3-
N/(m3 .d), and removal efficiencies higher than 90% were obtained
for loads up to 4.2 kg NO3-N/(m3 .d). A mass relation between COD
consumed and NO3-N removed around 2.82 was observed. This
continuous-flow bioreactor proved an efficient denitrification system
with a relatively low retention time.
Abstract: In Orthogonal Frequency Division Multiplexing (OFDM) systems, the peak to average power ratio (PAR) is much high. The clipping signal scheme is a useful method to reduce PAR. Clipping the OFDM signal, however, increases the overall noise level by introducing clipping noise. It is necessary to recover the figure of the original signal at receiver in order to reduce the clipping noise. Considering the continuity of the signal and the figure of the peak, we obtain a certain conic function curve to replace the clipped signal module within the clipping time. The results of simulation show that the proposed scheme can reduce the systems? BER (bit-error rate) 10 times when signal-to-interference-and noise-ratio (SINR) equals to 12dB. And the BER performance of the proposed scheme is superior to that of kim's scheme, too.
Abstract: Several methods are available for weight and shape
optimization of structures, among which Evolutionary Structural
Optimization (ESO) is one of the most widely used methods. In ESO,
however, the optimization criterion is completely case-dependent.
Moreover, only the improving solutions are accepted during the
search. In this paper a Simulated Annealing (SA) algorithm is used
for structural optimization problem. This algorithm differs from other
random search methods by accepting non-improving solutions. The
implementation of SA algorithm is done through reducing the
number of finite element analyses (function evaluations).
Computational results show that SA can efficiently and effectively
solve such optimization problems within short search time.
Abstract: Pressure wave velocity in a hydraulic system was
determined using piezo pressure sensors without removing fluid from
the system. The measurements were carried out in a low pressure
range (0.2 – 6 bar) and the results were compared with the results of
other studies. This method is not as accurate as measurement with
separate measurement equipment, but the fluid is in the actual
machine the whole time and the effect of air is taken into
consideration if air is present in the system. The amount of air is
estimated by calculations and comparisons between other studies.
This measurement equipment can also be installed in an existing
machine and it can be programmed so that it measures in real time.
Thus, it could be used e.g. to control dampers.
Abstract: Paced Auditory Serial Addition Test (PASAT) has
been used as a common research tool for different neurological
disorders like Multiple Sclerosis. Recently, technology let
researchers to introduce a new versions of the visual test, the paced
visual serial addition test (PVSAT). In this paper, the computerized
version of these two tests is introduced. Beside the number of true
responses are interpreted, the reaction time of subjects are calculated
by the software. We hypothesize that paying attention to the reaction
time may be valuable. For this purpose, sixty eight female normal
subjects and fifty eight male normal subjects are enrolled in the
study. We investigate the similarity between the PASAT3 and
PVSAT3 in number of true responses and the new criterion (the
average reaction time of each subject). The similarity between two
tests were rejected (p-value = 0.000) which means that these two test
differ. The effect of sex in the tests were not approved since the pvalues
of different between PASAT3 and PVSAT3 in both sex is the
same (p-value = 0.000) which means that male and female subjects
performed the tests at no different level of performance. The new
criterion shows a negative correlation with the age which offers aged
normal subjects may have the same number of true responses as the
young subjects but they have latent responses. This will give prove
for the importance of reaction time.
Abstract: Doubly fed induction machines DFIM are used
mainly for wind energy conversion in MW power plants. This paper
presents a new strategy of field oriented control ,it is based on the
principle of a double flux orientation of stator and rotor at the same
time. Therefore, the orthogonality created between the two oriented
fluxes, which must be strictly observed, leads to generate a linear and
decoupled control with an optimal torque. The obtained simulation
results show the feasibility and the effectiveness of the suggested
method.
Abstract: The authors of this work indicate by means of a concrete example that it is possible to apply efficaciously the method of multiple criteria programming in dealing with the problem of determining the optimal production plan for a certain period of time. The work presents: (1) the selection of optimization criteria, (2) the setting of the problem of determining an optimal production plan, (3) the setting of the model of multiple criteria programming in finding a solution to a given problem, (4) the revised surrogate trade-off method, (5) generalized multicriteria model for solving production planning problem and problem of choosing technological variants in the metal manufacturing industry. In the final part of this work the authors reflect on the application of the method of multiple criteria programming while determining the optimal production plan in manufacturing enterprises.
Abstract: Activated carbon was prepared from agricultural waste “almond (Prunus amygdalus) nut shells" by chemical activation with phosphoric acid as an activating agent at 450 °C for 24 hr soaking time. The physical and chemical properties were analyzed. The adsorption of chromium VI from aqueous solution on almond nut shell activated carbon (ASAC) was investigated. The adsorption process parameters pH, agitation speed, agitation time, adsorbent dose were optimized. 98% of Cr VI was sorbed at pH 2 and stirring speed 200 rpm.. Surface structure showed that ASAC has a spongy type structure showing large number of pores
Abstract: This study presents an investigation of
electrochemical variables and an application of the optimal
parameters in operating a continuous upflow electrocoagulation
reactor in removing dye. Direct red 23, which is azo-based, was used
as a representative of direct dyes. First, a batch mode was employed
to optimize the design parameters: electrode type, electrode distance,
current density and electrocoagulation time. The optimal parameters
were found to be iron anode, distance between electrodes of 8 mm
and current density of 30 A·m-2 with contact time of 5 min. The
performance of the continuous upflow reactor with these parameters
was satisfactory, with >95% color removal and energy consumption
in the order of 0.6-0.7 kWh·m-3.
Abstract: Theoptimal extraction condition of dried Phaseolus
vulgaris powderwas studied. The three independent variables are raw
material concentration, shaking and centrifugaltime. The dependent
variables are both yield percentage of crude extract and alphaamylase
enzyme inhibition activity. The experimental design was
based on box-behnkendesign. Highest yield percentage of crude
extract could get from extraction condition at concentration of 1, 0,1,
concentration of 0.15 M ,extraction time for 2hour, and
separationtime for60 min. Moreover, the crude extract with highest
alpha-amylase enzyme inhibition activityoccurred by extraction
condition at concentration of 0.10 M, extraction time for 2 min, and
separation time for 45 min
Abstract: Least Development Countries (LDC) like
Bangladesh, whose 25% revenue earning is achieved from Textile
export, requires producing less defective textile for minimizing
production cost and time. Inspection processes done on these
industries are mostly manual and time consuming. To reduce error
on identifying fabric defects requires more automotive and
accurate inspection process. Considering this lacking, this research
implements a Textile Defect Recognizer which uses computer
vision methodology with the combination of multi-layer neural
networks to identify four classifications of textile defects. The
recognizer, suitable for LDC countries, identifies the fabric defects
within economical cost and produces less error prone inspection
system in real time. In order to generate input set for the neural
network, primarily the recognizer captures digital fabric images by
image acquisition device and converts the RGB images into binary
images by restoration process and local threshold techniques.
Later, the output of the processed image, the area of the faulty
portion, the number of objects of the image and the sharp factor of
the image, are feed backed as an input layer to the neural network
which uses back propagation algorithm to compute the weighted
factors and generates the desired classifications of defects as an
output.