Abstract: The purpose of this study is to identify human walking vertical force by using FFT power spectrum density from the experimental acceleration data of the human body. An experiment on human walking is carried out on a stationary floor especially paying attention to higher components of dynamic vertical walking force. Based on measured acceleration data of the human lumbar part, not only in-phase component with frequency of 2fw, 3fw, but also in-opposite-phase component with frequency of 0.5 fw, 1.5 fw, 2.5 fw where fw is the walking rate is observed. The vertical vibration of pedestrian bridge induced by higher components of human walking vertical force is also discussed in this paper. A full scale measurement for the existing pedestrian bridge with center span length of 33 m is carried out focusing on the resonance phenomenon due to higher components of human walking vertical force. Dynamic response characteristics excited by these vertical higher components of human walking are revealed from the dynamic design viewpoint of pedestrian bridge.
Abstract: This paper presents a grid synchronization technique based on adaptive notch filter for SPV (Solar Photovoltaic) system along with MPPT (Maximum Power Point Tracking) techniques. An efficient grid synchronization technique offers proficient detection of various components of grid signal like phase and frequency. It also acts as a barrier for harmonics and other disturbances in grid signal. A reference phase signal synchronized with the grid voltage is provided by the grid synchronization technique to standardize the system with grid codes and power quality standards. Hence, grid synchronization unit plays important role for grid connected SPV systems. As the output of the PV array is fluctuating in nature with the meteorological parameters like irradiance, temperature, wind etc. In order to maintain a constant DC voltage at VSC (Voltage Source Converter) input, MPPT control is required to track the maximum power point from PV array. In this work, a variable step size P & O (Perturb and Observe) MPPT technique with DC/DC boost converter has been used at first stage of the system. This algorithm divides the dPpv/dVpv curve of PV panel into three separate zones i.e. zone 0, zone 1 and zone 2. A fine value of tracking step size is used in zone 0 while zone 1 and zone 2 requires a large value of step size in order to obtain a high tracking speed. Further, adaptive notch filter based control technique is proposed for VSC in PV generation system. Adaptive notch filter (ANF) approach is used to synchronize the interfaced PV system with grid to maintain the amplitude, phase and frequency parameters as well as power quality improvement. This technique offers the compensation of harmonics current and reactive power with both linear and nonlinear loads. To maintain constant DC link voltage a PI controller is also implemented and presented in this paper. The complete system has been designed, developed and simulated using SimPower System and Simulink toolbox of MATLAB. The performance analysis of three phase grid connected solar photovoltaic system has been carried out on the basis of various parameters like PV output power, PV voltage, PV current, DC link voltage, PCC (Point of Common Coupling) voltage, grid voltage, grid current, voltage source converter current, power supplied by the voltage source converter etc. The results obtained from the proposed system are found satisfactory.
Abstract: Second generation military Filipino Amerasians
comprise a formidable contemporary segment of the estimated
250,000-plus biracial Amerasians in the Philippines today. Overall,
they are a stigmatized and socioeconomically marginalized diaspora;
historically, they were abandoned or estranged by U.S. military
personnel fathers assigned during the century-long Colonial, Post-
World War II and Cold War Era of permanent military basing (1898-
1992). Indeed, U.S. military personnel are assigned in smaller
numbers in the Philippines today. This inquiry is an outgrowth of two
recent small sample studies. The first surfaced the impact of the U.S.
military prostitution system on formation of the ‘Derivative
Amerasian Family Construct’ on first generation Amerasians; a
second, qualitative case study suggested the continued effect of the
prostitution systems' destructive impetuous on second generation
Amerasians. The intent of this current qualitative, multiple-case study
was to actively seek out second generation sex industry toilers. The
purpose was to focus further on this human phenomenon in the postbasing
and post-military prostitution system eras. As background, the
former military prostitution apparatus has transformed into a modern
dynamic of rampant sex tourism and prostitution nationwide. This is
characterized by hotel and resorts offering unrestricted carnal access,
urban and provincial brothels (casas), discos, bars and pickup clubs,
massage parlors, local barrio karaoke bars and street prostitution. A
small case study sample (N = 4) of female and male second
generation Amerasians were selected. Sample formation employed a
non-probability ‘snowball’ technique drawing respondents from the
notorious Angeles, Metro Manila, Olongapo City ‘AMO Amerasian
Triangle’ where most former U.S. military installations were sited
and modern sex tourism thrives. A six-month study and analysis of
in-depth interviews of female and male sex laborers, their families
and peers revealed a litany of disturbing, and troublesome
experiences. Results showed profiles of debilitating human poverty,
history of family disorganization, stigmatization, social
marginalization and the ghost of the military prostitution system and
its harmful legacy on Amerasian family units. Emerging were testimonials of wayward young people ensnared in a maelstrom of
deep economic deprivation, familial dysfunction, psychological
desperation and societal indifference. The paper recommends that
more study is needed and implications of unstudied psychosocial and
socioeconomic experiences of distressed younger generations of
military Amerasians require specific research. Heretofore apathetic or
disengaged U.S. institutions need to confront the issue and formulate
activist and solution-oriented social welfare, human services and
immigration easement policies and alternatives. These institutions
specifically include academic and social science research agencies,
corporate foundations, the U.S. Congress, and Departments of State,
Defense and Health and Human Services, and Homeland Security
(i.e. Citizen and Immigration Services) It is them who continue to
endorse a laissez-faire policy of non-involvement over the entire
Filipino Amerasian question. Such apathy, the paper concludes,
relegates this consequential but neglected blood progeny to the status
of humiliating destitution and exploitation. Amerasians; thus, remain
entrapped in their former colonial, and neo-colonial habitat.
Ironically, they are unwitting victims of a U.S. American homeland
that fancies itself geo-politically as a strong and strategic military
treaty ally of the Philippines in the Western Pacific.
Abstract: A novel Active Flap System (AFS) has been developed
at DTU Wind Energy, as a result of a 3-year R&D project following
almost 10 years of innovative research in this field. The full scale AFS
comprises an active deformable trailing edge has been tested at the
unique rotating test facility at the Risø Campus of DTU Wind Energy
in Denmark. The design and instrumentation of the wing section and
the AFS are described. The general description and objectives of the
rotating test rig at the Risø campus of DTU are presented, along
with an overview of sensors on the setup and the test cases. The
post-processing of data is discussed and results of steady, flap step
and azimuth control flap cases are presented.
Abstract: The purpose of this research was to investigate the
creep behaviour of the heterogeneous Timber-UHPFRC beams. New
developments have been done to further improve the structural
performance, such as strengthening of the timber (glulam) beam by
bonding composite material combine with an ultra-high performance
fibre reinforced concrete (UHPFRC) internally reinforced with or
without carbon fibre reinforced polymer (CFRP) bars. However, in
the design of wooden structures, in addition to the criteria of
strengthening and stiffness, deformability due to the creep of wood,
especially in horizontal elements, is also a design criterion. Glulam,
UHPFRC and CFRP may be an interesting composite mix to respond
to the issue of creep behaviour of composite structures made of
different materials with different rheological properties. In this paper,
we describe an experimental and analytical investigation of the creep
performance of the glulam-UHPFRC-CFRP beams assembled by
bonding. The experimental investigations creep behaviour was
conducted for different environments: in- and outside under constant
loading for approximately a year. The measured results are compared
with numerical ones obtained by an analytical model. This model was
developed to predict the creep response of the glulam-UHPFRCCFRP
beams based on the creep characteristics of the individual
components. The results show that heterogeneous glulam-UHPFRC
beams provide an improvement in both the strengthening and
stiffness, and can also effectively reduce the creep deflection of
wooden beams.
Abstract: Networked environments which provide platforms for
business organizations are configured in different forms depending
on many factors including life time, member characteristics,
communication structure, and business objectives, among others.
With continuing advances in digital technologies the distance has
become a less barrier for business minded collaboration among
organizations. With the need and ease to make business collaborate
nowadays organizations are sometimes forced to co-work with others
that are either unknown or less known to them in terms of history and
performance. A promising approach for sustaining established
collaboration has been establishment of trust relationship among
organizations based on assessed trustworthiness for each participating
organization. It has been stated in research that trust in organization is
dynamic and thus assessment of trust level must address such
dynamic nature. This paper assesses relevant aspects of trust and
applies the assessed concepts to propose a semi-automated system for
the management of Sustainability and Evolution of trust in
organizations participating in specific objective in a networked
organizations environment.
Abstract: Salinity is one of the major factors limiting crop
production in an arid environment. Despite its global importance
soybean production suffer the problems of salinity stress causing
damages at plant development. So it is implacable to either search for
salinity enhancement of soybean plants. Therefore, in the current
study we try to clarify the mechanism that might be involved in the
ameliorating effects of osmo-protectants such as proline and glycine
betaine as well as, compost application on soybean plants grown
under salinity stress. The experiment was conducted under
greenhouse conditions at the Graduate School of Biosphere Science
Laboratory of Hiroshima University, Japan in 2011. The experiment
was designed as a spilt-split plot based on randomized complete
block design with four replications. The treatments could be
summarized as follows; (i) salinity concentrations (0 and 15 mM), (ii)
compost treatments (0 and 24 t ha-1) and (iii) the exogenous, proline
and glycine betaine concentrations (0 mM and 25 mM) for each.
Results indicated that salinity stress induced reduction in growth and
physiological aspects (dry weight per plant, chlorophyll content, N
and K+ content) of soybean plant compared with those of the
unstressed plants. On the other hand, salinity stress led to increases in
the electrolyte leakage ratio, Na and proline contents. Special
attention was paid to, the tolerance against salt stress was observed,
the improvement of salt tolerance resulted from proline, glycine
betaine and compost were accompanied with improved K+, and
proline accumulation. While, significantly decreased electrolyte
leakage ratio and Na+ content. These results clearly demonstrate that
harmful effect of salinity could reduce on growth aspects of soybean.
Consequently, exogenous osmoprotectants combine with compost
will effectively solve seasonal salinity stress problem and are a good
strategy to increase salinity resistance of soybean in the drylands.
Abstract: At the present time, awareness, education, computer
simulation and information systems protection are very serious and
relevant topics. The article deals with perspectives and possibilities of
implementation of emergence or natural hazard threats into the
system which is developed for communication among members of
crisis management staffs. The Czech Hydro-Meteorological Institute
with its System of Integrated Warning Service resents the largest
usable base of information. National information systems are connected to foreign systems,
especially to flooding emergency systems of neighboring countries,
systems of European Union and international organizations where the
Czech Republic is a member. Use of outputs of particular information
systems and computer simulations on a single communication
interface of information system for communication among members
of crisis management staff and setting the site interoperability in the
net will lead to time savings in decision-making processes in solving
extraordinary events and crisis situations. Faster managing of an
extraordinary event or a crisis situation will bring positive effects and
minimize the impact of negative effects on the environment.
Abstract: For the shrimp companies to remain relevant to its local
and international consumers, they must offer new shrimp product and
services. It must work actively not just to create value for the consumer,
but to involve the consumer in co-creating value for shrimp product
innovation in the market. In this theoretical work, we conceptualize the
business concept of value co-creation in the context of shrimp products,
and propose a framework of value co-creation for shrimp product
innovation in shrimp industries. With guidance on value co-creation in
in shrimp industry, and shrimp value chain actors mapped to the
co-creation cycle, companies can use the framework to offer new
shrimp product to consumer communities. Although customer
co-creation is known approach in the world, it is not commonly used
by the companies in Bangladesh. This paper makes an original
contribution by conceptualizing co-creation and set the examples of
best co-creation practices in food sector. The results of the study
provide management with guidelines for successful co-creation
projects with an innovation- and market-oriented approach. The
framework also provides a basis for further research in this area.
Abstract: Drought is one of the most serious problems posing a
grave threat to cereals production including maize. Maize
improvement in drought-stress tolerance poses a great challenge as
the global need for food and bio-energy increases. Thus, the current
study was planned to explore the variations and determine the
performance of target traits of maize hybrids at grain growth stage
under drought conditions during 2014 under Adana, Mediterranean
climate conditions, Turkey. Maize hybrids (Sancia, Indaco,
71May69, Aaccel, Calgary, 70May82, 72May80) were evaluated
under (irrigated and water stress). Results revealed that, grain yield
and yield traits had a negative effects because of water stress
conditions compared with the normal irrigation. As well as, based on
the result under normal irrigation, the maximum biological yield and
harvest index were recorded. According to the differences among
hybrids were found that, significant differences were observed among
hybrids with respect to yield and yield traits under current research. Based on the results, grain weight had more effect on grain yield
than grain number during grain filling growth stage under water
stress conditions. In this concern, according to low drought
susceptibility index (less grain yield losses), the hybrid (Indaco) was
more stable in grain number and grain weight. Consequently, it may
be concluded that this hybrid would be recommended for use in the
future breeding programs for production of drought tolerant hybrids.
Abstract: In Automotive Industry, sliding door systems that are
also used as body closures are safety members. Extreme product tests
are realized to prevent failures in design process, but these tests
realized experimentally result in high costs. Finite element analysis is
an effective tool used for design process. These analyses are used
before production of prototype for validation of design according to
customer requirement. In result of this, substantial amount of time
and cost is saved. Finite element model is created for geometries that are designed in
3D CAD programs. Different element types as bar, shell and solid,
can be used for creating mesh model. Cheaper model can be created
by selection of element type, but combination of element type that
was used in model, number and geometry of element and degrees of
freedom affects the analysis result. Sliding door system is a good
example which used these methods for this study. Structural analysis
was realized for sliding door mechanism by using FE models. As
well, physical tests that have same boundary conditions with FE
models were realized. Comparison study for these element types,
were done regarding test and analyses results then optimum
combination was achieved.
Abstract: In this study, failure analysis of pipe system at a micro
hydroelectric power plant is investigated. Failure occurred at the pipe
system in the powerhouse during shut down operation of the water
flow by a valve. This locking had caused a sudden shock wave, also
called “Water-hammer effect”, resulting in noise and inside pressure
increase. After visual investigation of the effect of the shock wave on
the system, a circumference crack was observed at the pipe flange
weld region. To establish the reason for crack formation, calculations
of pressure and stress values at pipe, flange and welding seams were
carried out and concluded that safety factor was high (2.2), indicating
that no faulty design existed. By further analysis, pipe system and
hydroelectric power plant was examined. After observations it is
determined that the plant did not include a ventilation nozzle (air
trap), that prevents the system of sudden pressure increase inside the
pipes which is caused by water-hammer effect. Analyses were carried
out to identify the influence of water-hammer effect on inside
pressure increase and it was concluded that, according Jowkowsky’s
equation, shut down time is effective on inside pressure increase. The
valve closing time was uncertain but by a shut down time of even one
minute, inside pressure would increase by 7.6 bar (working pressure
was 34.6 bar). Detailed investigations were also carried out on the
assembly of the pipe-flange system by considering technical
drawings. It was concluded that the pipe-flange system was not
installed according to the instructions. Two of five weld seams were
not applied and one weld was carried out faulty. This incorrect and
inadequate weld seams resulted in; insufficient connection of the pipe
to the flange constituting a strong notch effect at weld seam regions,
increase in stress values and the decrease of strength and safety
factor.
Abstract: Polymeric micro-cantilevers (Cs) are rapidly
becoming popular for MEMS applications such as chemo- and biosensing
as well as purely electromechanical applications such as
microrelays. Polymer materials present suitable physical and
chemical properties combined with low-cost mass production. Hence,
micro-cantilevers made of polymers indicate much more
biocompatibility and adaptability of rapid prototyping along with
mechanical properties. This research studies the effects of three
process and one size factors on the filling behaviour in micro cavity,
and the role of each in the replication of micro parts using different
polymer materials i.e. polypropylene (PP) SABIC 56M10 and
acrylonitrile butadiene styrene (ABS) Magnum 8434 . In particular,
the following factors are considered: barrel temperature, mould
temperature, injection speed and the thickness of micro features. The
study revealed that the barrel temperature and the injection speed are
the key factors affecting the flow length of micro features replicated
in PP and ABS. For both materials, an increase of feature sizes
improves the melt flow. However, the melt fill of micro features does
not increase linearly with the increase of their thickness.
Abstract: Elliptic curve discrete logarithm problem(ECDLP) is
one of problems on which the security of pairing-based cryptography
is based. This paper considers Pollard’s rho method to evaluate
the security of ECDLP on Barreto-Naehrig(BN) curve that is an
efficient pairing-friendly curve. Some techniques are proposed to
make the rho method efficient. Especially, the group structure on
BN curve, distinguished point method, and Montgomery trick are
well-known techniques. This paper applies these techniques and
shows its optimization. According to the experimental results for
which a large-scale parallel system with MySQL is applied, 94-bit
ECDLP was solved about 28 hours by parallelizing 71 computers.
Abstract: A multilayer passive shield composed of low-activity
lead (Pb), copper (Cu), tin (Sn) and iron (Fe) was designed and
manufactured for a coaxial HPGe detector placed at a surface
laboratory for reducing background radiation and radiation dose to
the personnel. The performance of the shield was evaluated and
efficiency curves of the detector were plotted by using of various
standard sources in different distances. Monte Carlo simulations and
a set of TLD chips were used for dose estimation in two distances of
20 and 40 cm. The results show that the shield reduced background
spectrum and the personnel dose more than 95%.
Abstract: This paper investigates the effectiveness of two
natural zeolites in reducing expansion of concrete due to alkali-silica
reaction. These natural zeolites have different reactive silica content.
Three aggregates; two natural sands and one crushed stone aggregate
were used while preparing mortar bars in accordance with accelerated
mortar bar test method, ASTM C1260. Performances of natural
zeolites are compared by examining the expansions due to alkali
silica reaction. Natural zeolites added to the mixtures at 10% and
20% replacement levels by weight of cement. Natural zeolite with
high reactive silica content had better performance on reducing
expansions due to ASR. In this research, using high reactive zeolite at
20% replacement levels was effective in mitigating expansions.
Abstract: Cole-Cole parameters of 40 post-menopausal women
are compared with their DEXA bone mineral density measurements.
Impedance characteristics of four extremities are compared; left and
right extremities are statistically same, but lower extremities are
statistically different than upper ones due to their different fat
content. The correlation of Cole-Cole impedance parameters to bone
mineral density (BMD) is observed to be higher for dominant arm.
With the post-menopausal population, ANOVA tests of the dominant
arm characteristic frequency, as a predictor for DEXA classified
osteopenic and osteoporic population around lumbar spine, is
statistically very significant. When used for total lumbar spine
osteoporosis diagnosis, the area under the Receiver Operating Curve
of the characteristic frequency is 0.830, suggesting that the Cole-Cole
plot characteristic frequency could be a useful diagnostic parameter
when integrated into standard screening methods for osteoporosis.
Moreover, the characteristic frequency can be directly measured by
monitoring frequency driven angular behavior of the dominant arm
without performing any complex calculation.
Abstract: Fiber Reinforced Polymer (FRP) is a composite material with exceptional properties that are capable to replace conventional steel reinforcement in reinforced and pre-stressed concrete structures. However, the main obstacle for their wide use in pre-stressed concrete application is the anchorage system. Due to the weakness of FRP in the transverse direction, the pre-stressing capacity of FRP bars are limited. This paper investigates the modification of the conventional wedge anchorage system to be used for stressing of FRP bars in pre-stressed applications. Epoxy adhesive material with glass FRP (GFRP) bars and conventional steel wedge were used in this paper. The GFRP bars are encased with epoxy at the anchor zone and the wedge system was used in pull-out test. The results showed a loading capacity of 47.6 kN which is 69% of the bar ultimate capacity. Additionally, nylon wedge was made with the same dimensions of the steel wedge and tested for GFRP bars without epoxy layer. The nylon wedge showed a loading capacity of 19.7 kN which is only 28.5% of the ultimate bar capacity.
Abstract: Passive control methods can be utilized to build
earthquake resistant structures, and also to strengthen the vulnerable
ones. In this paper, we studied the effect of this system in increasing
the ductility and energy dissipation and also modeled the behavior of
this type of eccentric bracing, and compared the hysteresis diagram
of the modeled samples with the laboratory samples. We studied
several samples of frames with vertical shear-links in order to assess
the behavior of this type of eccentric bracing. Each of these samples
was modeled in finite element software ANSYS 9.0, and was
analyzed under the static cyclic loading. It was found that vertical
shear-links have a more stable hysteresis loops. Another analysis
showed that using honeycomb beams as the horizontal beam along
with steel reinforcement has no negative effect on the hysteresis
behavior of the sample.
Abstract: This paper describes the collection and analysis of
data obtained from face-to-face interviews conducted in selected
Libyan industrial companies. The objectives of the interviews are to
enhance understanding, and generate explanations of current issues in
culture and quality management systems in Libyan companies. The
method used in analyzing the questions, as well as the main finding
of each question are explained. The interviews probed areas identify
national and organizational culture, quality management systems,
current methods, effects, barriers and other factors affecting the
success of quality management implementation. Eleven questions are
prepared and been discussed with the interviewees.