Abstract: Silica was extracted from agriculture waste rice husk
ash (RHA) and was used as the silica source for synthesis of
RMCM-48 and RSBA-16. An alkali fusion process was utilized to
separate silicate supernatant and the sediment effectively. The
CTAB/Si and F127/Si molar ratio was employed to control the
structure properties of the obtained RMCM-48 and RSBA-16
materials. The N2 adsorption-desorption results showed the
micro-mesoporous RSBA-16 possessed high specific surface areas
(662-1001 m2/g). All the obtained RSBA-16 materials were applied as
the adsorbents for acetone adsorption. And the breakthrough tests
clearly revealed that the RSBA-16(0.004) materials could achieve the
highest acetone adsorption capacity of 181 mg/g under 1000 ppmv
acetone vapor concentration at 25oC, which was also superior to
ZSM-5 (71mg/g) and MCM-41 (157mg/g) under same test conditions.
This can help to reduce the solid waste and the high adsorption
performance of the obtained materials could consider as potential
adsorbents for acetone adsorption.
Abstract: Properties of Portland cement mixtures with various
fractions of metakaolin were studied. 10% of Portland cement CEM I
42.5 R was replaced by different fractions of high reactivity
metakaolin with defined chemical and mineralogical properties.
Various fractions of metakaolin were prepared by jet mill classifying
system. There is a clear trend between fineness of metakaolin and
hydration heat development. Due to metakaolin presence in mixtures
the compressive strength development of mortars is rather slower for
coarser fractions but 28-day flexural strengths are improved for all
fractions of metakaoline used in mixtures compared to reference
sample of pure Portland cement. Yield point, plastic viscosity and
adhesion of fresh pastes are considerably influenced by fineness of
metakaolin used in cement pastes.
Abstract: In this study, the Compressive strength of concretes
made with Ground Granulated Blast furnace Slag (GGBS),
Pulverised Fuel Ash (PFA), Rice Husk Ash (RHA) and Waste Glass
Powder (WGP) after they were exposed 7800C (exposure duration of
around 60 minutes) and then allowed to cool down gradually in the
furnace for about 280 minutes at water binder ratio of 0.50 was
investigated. GGBS, PFA, RHA and WGP were used to replace up to
20% Portland cement in the control concrete. Test for the
determination of workability, compressive strength and tensile
splitting strength of the concretes were carried out and the results
were compared with control concrete. The test results showed that the
compressive strength decreased by an average of around 30% after
the concretes were exposed to the heating and cooling scenario.
Abstract: The capability of CNC gantry milling machines in
manufacturing long components has caused the expanded use of such
machines. On the other hand, the machines’ gantry rigidity can
reduce under severe loads or vibration during operation. Indeed, the
quality of machining is dependent on the machine’s dynamic
behavior throughout the operating process. For this reason, these
types of machines have always been used widely and are not
efficient. Therefore, they can usually be employed for rough
machining and may not produce adequate surface finishing. In this
paper, a CNC gantry milling machine with the potential to produce
good surface finish has been designed and analyzed. The lowest
natural frequency of this machine is 202 Hz corresponding to 12000
rpm at all motion amplitudes with a full range of suitable frequency
responses. Meanwhile, the maximum deformation under dead loads
for the gantry machine is 0.565*m, indicating that this machine tool
is capable of producing higher product quality.
Abstract: Knowledge is considered as an important asset which
can help organizations to create competitive advantage. The necessity
of taking care of these assets is more important in these days – in
days of turbulent changes in business environment. Knowledge could
facilitate adaption to constant changes. The aim of this paper is to
describe how the knowledge sharing can be supported in the
manufacturing companies. The methods of case studies and grounded
theory were used to present information gained by carrying out semistructured
interviews. Results show that knowledge sharing is
supported in very similar ways in respondent companies.
Abstract: Meeting the growth in demand for digital services
such as social media, telecommunications, and business and cloud
services requires large scale data centres, which has led to an increase
in their end use energy demand. Generally, over 30% of data centre
power is consumed by the necessary cooling overhead. Thus energy
can be reduced by improving the cooling efficiency. Air and liquid
can both be used as cooling media for the data centre. Traditional
data centre cooling systems use air, however liquid is recognised as a
promising method that can handle the more densely packed data
centres. Liquid cooling can be classified into three methods; rack heat
exchanger, on-chip heat exchanger and full immersion of the
microelectronics. This study quantifies the improvements of heat
transfer specifically for the case of immersed microelectronics by
varying the CPU and heat sink location. Immersion of the server is
achieved by filling the gap between the microelectronics and a water
jacket with a dielectric liquid which convects the heat from the CPU
to the water jacket on the opposite side. Heat transfer is governed by
two physical mechanisms, which is natural convection for the fixed
enclosure filled with dielectric liquid and forced convection for the
water that is pumped through the water jacket. The model in this
study is validated with published numerical and experimental work
and shows good agreement with previous work. The results show that
the heat transfer performance and Nusselt number (Nu) is improved
by 89% by placing the CPU and heat sink on the bottom of the
microelectronics enclosure.
Abstract: The concentrations of cadmium and lead in sewage
sludge samples were determined by Atomic Absorption
Spectrometric Method. Samples of sewage sludge were obtained
from three sewage treatment plants localised in Middle Region of
Libya (Misrata, Msallata and Tarhünah cities).
The results shows that, the mean levels of Cadmium for all regions
are ranges from 81 to 123.4 ppm and these values are higher than the
limitations for the international standard which are not registered
more than 50 ppm (dry weight) in USA, Egypt and the EU countries.
While, the lead concentrations are ranged from 8.0 to 189.2 ppm and
all values are within the standard limits which graduated between
(275–613) ppm.
Abstract: In this paper, the author studied the possibilities of
using Rice Husk Ash (RHA) available in India; to produce concrete.
Experiments conducted with RHA obtained from West Bengal, India;
to replace cement partially to produce concrete of grade M10, M15,
M20, M25 and M30. The concrete produced in the laboratory by
replacing cement by 5%, 10%, 15%, 20%, 25% and 30% RHA.
Compressive strength tests carried out to determine the strength of
concrete. Cost analysis and comparison done to show the cost
effectiveness of RHA Concrete. Traditional uses of Rice Husk in
India pointed out and the advantages of using RHA in making
concrete highlighted. Suggestion provided regarding prospective
application of RHA concrete in India; which in turn will definitely
reduce the cost of concrete and environmental friendly due to
utilization of waste and replacement of Cement.
Abstract: The rhizome of Java grass, Cyperus rotundus was
extracted different organic polar and non-polar solvents and
performed the in vitro antiviral and immunostimulant activities
against White Spot Syndrome Virus (WSSV) and Vibrio harveyi
respectively. Based on the initial screening the ethyl acetate extract of
C. rotundus was strong activities and further it was purified through
silica column chromatography and the fractions were screened again
for antiviral and immunostimulant activity. Among the different
fractions screened against the WSSV and V. harveyi, the fractions, FIII
to FV had strong activities. In order to study the in vivo influence
of C. rotundus, the fractions (F-III to FV) were pooled and delivered
to the F. indicus through artificial feed for 30 days. After the feeding
trail the experimental and control diet fed F. indicus were challenged
with virulent WSSV and studied the survival, molecular diagnosis,
biochemical, haematological, and immunological parameters.
Surprisingly, the pooled fractions (F-IV to FVI) incorporated diets
helped to significantly (P
Abstract: Ti6Al4V alloy is highly used in the automotive and
aerospace industry due to its good machining characteristics. Micro
EDM drilling is commonly used to drill micro hole on extremely hard
material with very high depth to diameter ratio. In this study, the
parameters of micro-electrical discharge machining (EDM) in drilling
of Ti6Al4V alloy is optimized for higher machining accuracy with
less hole-dilation and hole taper ratio. The micro-EDM machining
parameters includes, peak current and pulse on time. Fuzzy analysis
was developed to evaluate the machining accuracy. The analysis
shows that hole-dilation and hole-taper ratio are increased with the
increasing of peak current and pulse on time. However, the surface
quality deteriorates as the peak current and pulse on time increase.
The combination that gives the optimum result for hole dilation is
medium peak current and short pulse on time. Meanwhile, the
optimum result for hole taper ratio is low peak current and short pulse
on time.
Abstract: In this paper, groundwater seepage into Amirkabir
tunnel has been estimated using analytical and numerical methods for
14 different sections of the tunnel. Site Groundwater Rating (SGR)
method also has been performed for qualitative and quantitative
classification of the tunnel sections. The obtained results of above
mentioned methods were compared together. The study shows
reasonable accordance with results of the all methods unless for two
sections of tunnel. In these two sections there are some significant
discrepancies between numerical and analytical results mainly
originated from model geometry and high overburden. SGR and the
analytical and numerical calculations, confirm high concentration of
seepage inflow in fault zones. Maximum seepage flow into tunnel has
been estimated 0.425 lit/sec/m using analytical method and 0.628
lit/sec/m using numerical method occured in crashed zone. Based on
SGR method, six sections of 14 sections in Amirkabir tunnel axis are
found to be in "No Risk" class that is supported by the analytical and
numerical seepage value of less than 0.04 lit/sec/m.
Abstract: At present, the cascade PID control is widely used to
control the superheating temperature (main steam temperature). As
Main Steam Temperature has the characteristics of large inertia, large
time-delay and time varying, etc., conventional PID control strategy
cannot achieve good control performance. In order to overcome the
bad performance and deficiencies of main steam temperature control
system, Model Free Adaptive Control (MFAC) - P cascade control
system is proposed in this paper. By substituting MFAC in PID of the
main control loop of the main steam temperature control, it can
overcome time delays, non-linearity, disturbance and time variation.
Abstract: The wide use of the Internet-based applications bring many challenges to the researchers to guarantee the continuity of the connections needed by the mobile hosts and provide reliable Internet access for them. One of proposed solutions by Internet Engineering Task Force (IETF) is to connect the local, multi-hop, and infrastructure-less Mobile Ad hoc Network (MANET) with Internet structure. This connection is done through multi-interface devices known as Internet Gateways. Many issues are related to this connection like gateway discovery, handoff, address auto-configuration and selecting the optimum gateway when multiple gateways exist. Many studies were done proposing gateway selection schemes with a single selection criterion or weighted multiple criteria. In this research, a review of some of these schemes is done showing the differences, the features, the challenges and the drawbacks of each of them.
Abstract: Standard processes, similar and limited production
lines, the production of high direct costs will be more accurate than
the use of parts of the traditional cost systems in the literature.
However, direct costs, overhead expenses, in turn, decrease the
burden of increasingly sophisticated production facilities, a situation
that led the researchers to look for the cost of traditional systems of
alternative techniques. Variety cost management approaches for
example Total quality management (TQM), just-in-time (JIT),
benchmarking, kaizen costing, targeting cost, life cycle costs (LLC),
activity-based costing (ABC) value engineering have been
introduced. Management and cost applications have changed over the
past decade and will continue to change. Modern cost systems can
provide relevant and accurate cost information. These methods
provide the decisions about customer, product and process
improvement. The aim of study is to describe and explain the
adoption and application of costing systems in SME. This purpose
reports on a survey conducted during 2014 small and medium sized
enterprises (SME) in Ankara. The survey results were evaluated
using SPSS18 package program.
Abstract: The detection of the polymer melt state during
manufacture process is regarded as an efficient way to control the
molded part quality in advance. Online monitoring rheological
property of polymer melt during processing procedure provides an
approach to understand the melt state immediately. Rheological
property reflects the polymer melt state at different processing
parameters and is very important in injection molding process
especially. An approach that demonstrates how to calculate
rheological property of polymer melt through in-process
measurement, using injection molding as an example, is proposed in
this study. The system consists of two sensors and a data acquisition
module can process the measured data, which are used for the
calculation of rheological properties of polymer melt. The rheological
properties of polymer melt discussed in this study include shear rate
and viscosity which are investigated with respect to injection speed
and melt temperature. The results show that the effect of injection
speed on the rheological properties is apparent, especially for high
melt temperature and should be considered for precision molding
process.
Abstract: Doxorubicin, also known as Adriamycin, is an
anthracycline class of drug used in cancer chemotherapy. It is used in
the treatment of non-Hodgkin’s lymphoma, multiple myeloma, acute
leukemia, breast cancer, lung cancer, endometrium cancer and ovary
cancers. It functions via intercalating DNA and ultimately killing
cancer cells. The major side effects of doxorubicin are hair loss,
myelosuppression, nausea & vomiting, oesophagitis, diarrhea, heart
damage and liver dysfunction. The minor modifications in the
structure of compound exhibit large variation in the biological
activity, has prompted us to carry out the synthesis of sulfonamide
derivatives. Sulfonamide is an important feature with broad spectrum
of biological activity such as antiviral, antifungal, diuretics, antiinflammatory,
antibacterial and anticancer activities. Structure of the
synthesized compound N-(1-methyl-2-oxo-2-N-methyl anilinoethyl)
benzene sulfonamide confirmed by proton nuclear magnetic
resonance (1H NMR),13C NMR, Mass and FTIR spectroscopic tools
to assure the position of all protons and hence stereochemistry of the
molecule. Further we have reported the binding potential of
synthesized sulfonamide analogues in comparison to doxorubicin
drug using Auto Dock 4.2 software. Computational binding energy
(B.E.) and inhibitory constant (Ki) has been evaluated for the
synthesized compound in comparison of doxorubicin against Poly
(dA-dT).Poly (dA-dT) and Poly (dG-dC).Poly (dG-dC) sequences.
The in vitro cytotoxic study against human breast cancer cell lines
confirms the better anticancer activity of the synthesized compound
over currently in use anticancer drug doxorubicin. The IC50 value of
the synthesized compound is 7.12 μM whereas for doxorubicin is 7.2
μM.
Abstract: In order to detect and quantify the phenolic contents
of a wastewater with biosensors, two working electrodes based on
modified Poly(Pyrrole) films were fabricated. Enzyme horseradish
peroxidase was used as biomolecule of the prepared electrodes.
Various phenolics were tested at the biosensor. Phenol detection was
realized by electrochemical reduction of quinones produced by
enzymatic activity. Analytical parameters were calculated and the
results were compared with each other.
Abstract: The work studied the effect of germination on
proximate, phenol and flavonoid content and antioxidant activities
(AOA) of African Yam been (AYB). Germination was done in
controlled dark chamber (100% RH, 28oC). The proximate, phenol
and flavonoid content and antioxidant activities before and after
germination were investigated. The crude protein, moisture, and
crude fiber content of germinated AYB were significantly higher
(P
Abstract: In this study, we have focused our attention on
combining of molecular imprinting into nanofilms and QCM
nanosensor approaches and producing QCM nanosensor for anti-
CCP, chosen as model protein, using anti-CCP imprinted nanofilms.
The nonimprinted nanosensor was also prepared to evaluate the
selectivity of the imprinted nanosensor. Anti-CCP imprinted QCM
nanosensor was tested for real time detection of anti-CCP from
aqueous solution. The kinetic and affinity studies were determined by
using anti-CCP solutions with different concentrations. The
responses related with mass shifts (%m) and frequency shifts (%f)
were used to evaluate adsorption properties. To show the selectivity
of the anti-CCP imprinted QCM nanosensor, competitive adsorption
of anti-CCP and IgM was investigated. The results indicate that anti-
CCP imprinted QCM nanosensor has higher adsorption capabilities
for anti-CCP than for IgM, due to selective cavities in the polymer
structure.
Abstract: This study evaluated the use of raw or processed
Prosopis juliflora (Meskit) pods as a major ingredient in a formulated
ration to provide an alternative non-conventional concentrate for
livestock feeding in Oman. Dry Meskit pods were reduced to lengths
of 0.5- 1.0 cm to ensure thorough mixing into three diets. Meskit
pods were subjected to two types of treatments; roasting and soaking.
They were roasted at 150оC for 30 minutes using a locally-made
roasting device (40 kg barrel container rotated by electric motor and
heated by flame gas cooker). Chopped pods were soaked in tap water
for 24 hours and dried for 2 days under the sun with frequent turning.
The Meskit-pod-based diets (MPBD) were formulated and pelleted
from 500 g/kg ground Meskit pods, 240 g/kg wheat bran, 200 g/kg
barley grain, 50 g/kg local dried sardines and 10 g/kg of salt. Twenty
four 10 months-old intact Omani male lambs with average body
weight of 27.3 kg (± 0.5 kg) were used in a feeding trial for 84 days.
They were divided (on body weight basis) and allocated to four diet
combination groups. These were: Rhodes grass hay (RGH) plus a
general ruminant concentrate (GRC); RGH plus raw Meskit pods
(RMP) based concentrate; RGH plus roasted Meskit pods (ROMP)
based concentrate; RGH plus soaked Meskit pods (SMP) based
concentrate Daily feed intakes and bi-weekly body weights were
recorded. MPBD had higher contents of crude protein (CP), acid
detergent fibre (ADF) and neutral detergent fibre (NDF) than the
GRC. Animals fed various types of MPBD did not show signs of ill
health. There was a significant effect of feeding ROMP on the
performance of Omani sheep compared to RMP and SMP. The
ROMP fed animals had similar performance to those fed the GRC in
terms of feed intake, body weight gain and feed conversion ratio
(FCR).This study indicated that roasted Meskit pods based diet may
be used instead of the commercial concentrate for feeding Omani
sheep without adverse effects on performance. It offers a cheap
alternative source of protein and energy for feeding Omani sheep.
Also, it might help in solving the spread impact of Meskit trees,
maintain the ecosystem and helping in preserving the local tree
species.