Abstract: This paper outlines the basic installation and operation of magnetic inductive flow velocity sensors on large underground cooling water pipelines. Research on the effects of cathodic protection as well as into other factors that might influence the overall performance of the meter is presented in this paper. The experiments were carried out on an immersion type magnetic meter specially used for flow measurement of cooling water pipeline. An attempt has been made in this paper to outline guidelines that can ensure accurate measurement related to immersion type magnetic meters on underground pipelines.
Abstract: In order to detect and quantify the phenolic contents
of a wastewater with biosensors, two working electrodes based on
modified Poly(Pyrrole) films were fabricated. Enzyme horseradish
peroxidase was used as biomolecule of the prepared electrodes.
Various phenolics were tested at the biosensor. Phenol detection was
realized by electrochemical reduction of quinones produced by
enzymatic activity. Analytical parameters were calculated and the
results were compared with each other.
Abstract: This paper presents two types of microstrip bandpass
filter (BPF) at microwave frequencies. The first one is a tunable BPF
using planar patch resonators based on a varactor diode. The filter is
formed by a triple mode circular patch resonator with two pairs of
slots, in which the varactor diodes are connected. Indeed, this filter is
initially centered at 2.4 GHz; the center frequency of the tunable
patch filter could be tuned up to 1.8 GHz simultaneously with the
bandwidth, reaching high tuning ranges. Lossless simulations were
compared to those considering the substrate dielectric, conductor
losses and the equivalent electrical circuit model of the tuning
element in order to assess their effects. Within these variations,
simulation results showed insertion loss better than 2 dB and return
loss better than 10 dB over the passband. The second structure is a
BPF for ultra-wideband (UWB) applications based on multiple-mode
resonator (MMR) and rectangular-shaped defected ground structure
(DGS). This filter, which is compact size of 25.2 x 3.8 mm2, provides
in the pass band an insertion loss of 0.57 dB and a return loss greater
than 12 dB. The proposed filters presents good performances and the
simulation results are in satisfactory agreement with the
experimentation ones reported elsewhere.
Abstract: This paper discusses the undesirable charge transfer
through the parasitic capacitances of the input transistors in a
multi-inputs voltage sense amplifier. Its intrinsic rail-to-rail voltage
transitions at the output nodes inevitably disturb the input sides
through the capacitive coupling between the outputs and inputs. Then,
it can possible degrade the stabilities of the reference voltage levels.
Moreover, it becomes more serious in multi-channel systems by
altering them for other channels, and so degrades the linearity of the
overall systems. In order to alleviate the internal node voltage
transition, the internal node stabilization techniques are proposed. It
achieves 45% and 40% improvements for node stabilization and input
referred disturbance, respectively.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: Newly synthesized Polypropylene-g-Polyethylene
glycol polymer was first time used for a compartment-less enzymatic
fuel cell. Working electrodes based on Polypropylene-g-Polyethylene
glycol were operated as unmediated and mediated system (with
ferrocene and gold/cobalt oxide nanoparticles). Glucose oxidase and
bilirubin oxidase was selected as anodic and cathodic enzyme,
respectively. Glucose was used as fuel in a single-compartment and
membrane-less cell. Maximum power density was obtained as 0.65
nW cm-2, 65 nW cm-2 and 23500 nW cm-2 from the unmediated,
ferrocene and gold/cobalt oxide modified polymeric film,
respectively. Power density was calculated to be ~16000 nW cm-2 for
undiluted wastewater sample with gold/cobalt oxide nanoparticles
including system.
Abstract: This study evaluated the use of raw or processed
Prosopis juliflora (Meskit) pods as a major ingredient in a formulated
ration to provide an alternative non-conventional concentrate for
livestock feeding in Oman. Dry Meskit pods were reduced to lengths
of 0.5- 1.0 cm to ensure thorough mixing into three diets. Meskit
pods were subjected to two types of treatments; roasting and soaking.
They were roasted at 150оC for 30 minutes using a locally-made
roasting device (40 kg barrel container rotated by electric motor and
heated by flame gas cooker). Chopped pods were soaked in tap water
for 24 hours and dried for 2 days under the sun with frequent turning.
The Meskit-pod-based diets (MPBD) were formulated and pelleted
from 500 g/kg ground Meskit pods, 240 g/kg wheat bran, 200 g/kg
barley grain, 50 g/kg local dried sardines and 10 g/kg of salt. Twenty
four 10 months-old intact Omani male lambs with average body
weight of 27.3 kg (± 0.5 kg) were used in a feeding trial for 84 days.
They were divided (on body weight basis) and allocated to four diet
combination groups. These were: Rhodes grass hay (RGH) plus a
general ruminant concentrate (GRC); RGH plus raw Meskit pods
(RMP) based concentrate; RGH plus roasted Meskit pods (ROMP)
based concentrate; RGH plus soaked Meskit pods (SMP) based
concentrate Daily feed intakes and bi-weekly body weights were
recorded. MPBD had higher contents of crude protein (CP), acid
detergent fibre (ADF) and neutral detergent fibre (NDF) than the
GRC. Animals fed various types of MPBD did not show signs of ill
health. There was a significant effect of feeding ROMP on the
performance of Omani sheep compared to RMP and SMP. The
ROMP fed animals had similar performance to those fed the GRC in
terms of feed intake, body weight gain and feed conversion ratio
(FCR).This study indicated that roasted Meskit pods based diet may
be used instead of the commercial concentrate for feeding Omani
sheep without adverse effects on performance. It offers a cheap
alternative source of protein and energy for feeding Omani sheep.
Also, it might help in solving the spread impact of Meskit trees,
maintain the ecosystem and helping in preserving the local tree
species.
Abstract: The aim of this paper is to perform experimental
modal analysis (EMA) of reinforced concrete (RC) square slabs.
EMA is the process of determining the modal parameters (Natural
Frequencies, damping factors, modal vectors) of a structure from a
set of frequency response functions FRFs (curve fitting). Although,
experimental modal analysis (or modal testing) has grown steadily in
popularity since the advent of the digital FFT spectrum analyzer in
the early 1970’s, studying all types of members and materials using
such method have not yet been well documented. Therefore, in this
work, experimental tests were conducted on RC square slab
specimens of dimensions 600mm x 600mmx 40mm. Experimental
analysis was based on freely supported boundary condition.
Moreover, impact testing as a fast and economical means of finding
the modes of vibration of a structure was used during the
experiments. In addition, Pico Scope 6 device and MATLAB
software were used to acquire data, analyze and plot Frequency
Response Function (FRF). The experimental natural frequencies
which were extracted from measurements exhibit good agreement
with analytical predictions. It is showed that EMA method can be
usefully employed to investigate the dynamic behavior of RC slabs.
Abstract: The practice of freeing monuments from subsequent
additions crosses the entire history of conservation and it is
traditionally connected to the aim of valorisation, both for cultural
and educational purpose and recently even for touristic exploitation.
Defence heritage has been widely interested by these cultural and
technical moods from philological restoration to critic innovations. A
renovated critical analysis of Italian episodes and in particular the
Sardinian case of the area of San Pancrazio in Cagliari, constitute an
important lesson about the limits of this practice and the uncertainty
in terms of results, towards the definition of a sustainable good
practice in the restoration of military architectures.
Abstract: This paper presents small signal stability study carried
over the 140-Bus, 31-Machine, 5-Area MEPE system and validated
on free and open source software: PSAT. Well-established linearalgebra
analysis, eigenvalue analysis, is employed to determine the
small signal dynamic behavior of test system. The aspects of local
and interarea oscillations which may affect the operation and
behavior of power system are analyzed. Eigenvalue analysis is carried
out to investigate the small signal behavior of test system and the
participation factors have been determined to identify the
participation of the states in the variation of different mode shapes.
Also, the variations in oscillatory modes are presented to observe the
damping performance of the test system.
Abstract: Elastomeric dielectric material has recently become a
new alternative for actuator technology. The characteristics of
dielectric elastomers placed between two electrodes to withstand
large strain when electrodes are charged has attracted the attention of
many researcher to study this material for actuator technology. Thus,
in the past few years Danfoss Ventures A/S has established their own
dielectric electro-active polymer (DEAP), which was called
PolyPower.
The main objective of this work was to investigate the dynamic
characteristics for vibration control of a PolyPower actuator folded in
‘pull’ configuration. A range of experiments was carried out on the
folded actuator including passive (without electrical load) and active
(with electrical load) testing. For both categories static and dynamic
testing have been done to determine the behavior of folded DEAP
actuator.
Voltage-Strain experiments show that the DEAP folded actuator is
a non-linear system. It is also shown that the voltage supplied has no
effect on the natural frequency. Finally, varying AC voltage with
different amplitude and frequency shows the parameters that
influence the performance of DEAP folded actuator. As a result, the
actuator performance dominated by the frequency dependence of the
elastic response and was less influenced by dielectric properties.
Abstract: Geometric and mechanical properties all influence the
resistance of RC structures and may, in certain combination of
property values, increase the risk of a brittle failure of the whole
system.
This paper presents a statistical and probabilistic investigation on
the resistance of RC beams designed according to Eurocodes 2 and 8,
and subjected to multiple failure modes, under both the natural
variation of material properties and the uncertainty associated with
cross-section and transverse reinforcement geometry. A full
probabilistic model based on JCSS Probabilistic Model Code is
derived. Different beams are studied through material nonlinear
analysis via Monte Carlo simulations. The resistance model is
consistent with Eurocode 2. Both a multivariate statistical evaluation
and the data clustering analysis of outcomes are then performed.
Results show that the ultimate load behaviour of RC beams
subjected to flexural and shear failure modes seems to be mainly
influenced by the combination of the mechanical properties of both
longitudinal reinforcement and stirrups, and the tensile strength of
concrete, of which the latter appears to affect the overall response of
the system in a nonlinear way. The model uncertainty of the
resistance model used in the analysis plays undoubtedly an important
role in interpreting results.
Abstract: This study concerned the dynamic behavior of the
wind turbine rotor. Before all we have studied the loads applied to the
rotor, which allows the knowledge their effect on the fatigue, also
studied the rotor with longitudinal crack in order to determine stress,
strain and displacement. Firstly we compared the first six modes
shapes between cracking and uncracking of HAWT rotor. Secondly
we show show evolution of first six natural frequencies with
longitudinal crack propagation. Finally we conclude that the residual
change in the natural frequencies can be used as in shaft crack
diagnosis predictive maintenance.
Abstract: The progress of industry integrated circuits in recent
years has been pushed by continuous miniaturization of transistors.
With the reduction of dimensions of components at 0.1 micron and
below, new physical effects come into play as the standard simulators
of two dimensions (2D) do not consider. In fact the third dimension
comes into play because the transverse and longitudinal dimensions
of the components are of the same order of magnitude. To describe
the operation of such components with greater fidelity, we must
refine simulation tools and adapted to take into account these
phenomena. After an analytical study of the static characteristics of
the component, according to the different operating modes, a
numerical simulation is performed of field-effect transistor with
submicron gate MESFET GaInP. The influence of the dimensions of
the gate length is studied. The results are used to determine the
optimal geometric and physical parameters of the component for their
specific applications and uses.
Abstract: Iris codes contain bits with different entropy. This
work investigates different strategies to reduce the size of iris
code templates with the aim of reducing storage requirements and
computational demand in the matching process. Besides simple subsampling
schemes, also a binary multi-resolution representation as
used in the JBIG hierarchical coding mode is assessed. We find that
iris code template size can be reduced significantly while maintaining
recognition accuracy. Besides, we propose a two-stage identification
approach, using small-sized iris code templates in a pre-selection
stage, and full resolution templates for final identification, which
shows promising recognition behaviour.
Abstract: The mechanics of rip currents are complex, involving
interactions between waves, currents, water levels and the bathymetry,
that present particular challenges for numerical models. Here,
the effects of a grid-spacing dependent horizontal mixing on the
wave-current interactions are studied. Near the shore, wave rays
diverge from channels towards bar crests because of refraction by
topography and currents, in a way that depends on the rip current
intensity which is itself modulated by the horizontal mixing. At
low resolution with the grid-spacing dependent horizontal mixing,
the wave motion is the same for both coupling modes because the
wave deviation by the currents is weak. In high resolution case,
however, classical results are found with the stabilizing effect of
the flow by feedback of waves on currents. Lastly, wave-current
interactions and the horizontal mixing strongly affect the intensity
of the three-dimensional rip velocity.
Abstract: The contact resistance between source/drain electrodes
and semiconductor layer is an important parameter affecting electron
transporting performance in the thin film transistor (TFT). In this
work, we introduced a transparent and the solution prossable
single-walled carbon nanotube (SWCNT)/Al-doped ZnO nano particle
(AZO NP) bilayer electrodes showing low contact resistance with
indium-oxide (In2O3) sol gel thin film. By inserting low work function
AZO NPs into the interface between the SWCNTs and the In2O3 which
has a high energy barrier, we could obtain an electrical Ohmic contact
between them. Finally, with the SWCNT-AZO NP bilayer electrodes,
we successfully fabricated a TFT showing a field effect mobility of
5.38 cm2/V·s at 250°C.
Abstract: The idea of the asynchronous transmission in
wavelength division multiplexing (WDM) ring MANs is studied in
this paper. Especially, we present an efficient access technique to
coordinate the collisions-free transmission of the variable sizes of IP
traffic in WDM ring core networks. Each node is equipped with a
tunable transmitter and a tunable receiver. In this way, all the
wavelengths are exploited for both transmission and reception. In
order to evaluate the performance measures of average throughput,
queuing delay and packet dropping probability at the buffers, a
simulation model that assumes symmetric access rights among the
nodes is developed based on Poisson statistics. Extensive numerical
results show that the proposed protocol achieves apart from high
bandwidth exploitation for a wide range of offered load, fairness of
queuing delay and dropping events among the different packets size
categories.
Abstract: Wireless mesh networking is rapidly gaining in
popularity with a variety of users: from municipalities to enterprises,
from telecom service providers to public safety and military
organizations. This increasing popularity is based on two basic facts:
ease of deployment and increase in network capacity expressed in
bandwidth per footage; WMNs do not rely on any fixed
infrastructure. Many efforts have been used to maximizing
throughput of the network in a multi-channel multi-radio wireless
mesh network. Current approaches are purely based on either static or
dynamic channel allocation approaches. In this paper, we use a
hybrid multichannel multi radio wireless mesh networking
architecture, where static and dynamic interfaces are built in the
nodes. Dynamic Adaptive Channel Allocation protocol (DACA), it
considers optimization for both throughput and delay in the channel
allocation. The assignment of the channel has been allocated to be codependent
with the routing problem in the wireless mesh network and
that should be based on passage flow on every link. Temporal and
spatial relationship rises to re compute the channel assignment every
time when the pattern changes in mesh network, channel assignment
algorithms assign channels in network. In this paper a computing
path which captures the available path bandwidth is the proposed
information and the proficient routing protocol based on the new path
which provides both static and dynamic links. The consistency
property guarantees that each node makes an appropriate packet
forwarding decision and balancing the control usage of the network,
so that a data packet will traverse through the right path.
Abstract: In this study, data loss tolerance of Support Vector Machines (SVM) based activity recognition model and multi activity classification performance when data are received over a lossy wireless sensor network is examined. Initially, the classification algorithm we use is evaluated in terms of resilience to random data loss with 3D acceleration sensor data for sitting, lying, walking and standing actions. The results show that the proposed classification method can recognize these activities successfully despite high data loss. Secondly, the effect of differentiated quality of service performance on activity recognition success is measured with activity data acquired from a multi hop wireless sensor network, which introduces high data loss. The effect of number of nodes on the reliability and multi activity classification success is demonstrated in simulation environment. To the best of our knowledge, the effect of data loss in a wireless sensor network on activity detection success rate of an SVM based classification algorithm has not been studied before.