Abstract: Magnetic powder of Sr-ferrite was prepared by
conventional and sol-gel auto-combustion methods. In conventional
method, strontium carbonate and ferric oxide powders were mixed
together and then mixture was calcined. In sol-gel auto-combustion
method, a solution containing strontium nitrate, ferric nitrate and
citric acid was heated until the combustion took place automatically;
then, as-burnt powder was calcined. Thermal behavior, phase
identification, morphology and magnetic properties of powders
obtained by these two methods were compared by DTA, XRD, SEM
and VSM techniques. According to the results of DTA analysis,
formation temperature of Sr-ferrite obtained by conventional and solgel
auto-combustion methods were 1300°C and 1000°C, respectively.
XRD results confirmed the formation of pure Sr-ferrite at the
mentioned temperatures. Plate and hexagonal-shape particles of Srferrite
were observed using SEM. The Sr-ferrite powder obtained by
sol-gel auto-combustion method had saturation magnetization of
66.03 emu/g and coercivity of 5731 Oe in comparison with values of
58.20 emu/g and 4378 Oe obtained by conventional method.
Abstract: Calcium phosphate cement (CPC) is one of the most
attractive bioceramics due to its moldable and shape ability to fill
complicated bony cavities or small dental defect positions. In this
study, CPC was produced by using mixture of tetracalcium phosphate
(TTCP, Ca4O(PO4)2) and dicalcium phosphate anhydrous (DCPA,
CaHPO4) in equimolar ratio (1/1) with aqueous solutions of acetic
acid (C2H4O2) and disodium hydrogen phosphate dehydrate
(Na2HPO4.2H2O) in combination with sodium alginate in order to
improve theirs moldable characteristic. The concentration of the
aqueous solutions and sodium alginate were varied to investigate the
effect of different aqueous solutions and alginate on properties of the
cements. The cement paste was prepared by mixing cement powder
(P) with aqueous solution (L) in a P/L ratio of 1.0g/0.35ml. X-ray
diffraction (XRD) was used to analyses phase formation of the
cements. Setting time and compressive strength of the set CPCs were
measured using the Gilmore apparatus and Universal testing
machine, respectively.
The results showed that CPCs could be produced by using both
basic (Na2HPO4.2H2O) and acidic (C2H4O2) solutions. XRD results
show the precipitation of hydroxyapatite in all cement samples. No
change in phase formation among cements using difference
concentrations of Na2HPO4.2H2O solutions. With increasing
concentration of acidic solutions, samples obtained less
hydroxyapatite with a high dicalcium phosphate dehydrate leaded to
a shorter setting time. Samples with sodium alginate exhibited higher
crystallization of hydroxyapatite than that of without alginate as a
result of shorten setting time in a basic solution but a longer setting
time in an acidic solution. The stronger cement was attained from
samples using the acidic solution with sodium alginate; however the
strength was lower than that of using the basic solution.
Abstract: The liver is the strongest regenerating organ of the
organism, and even with 2/3 surgically removed, it can regenerate
completely. Hence liver cirrhosis may only develop when the
regenerating system is off.
We present the results of a comparative study of structural and
functional characteristics of rat liver tissue under the conditions of
toxic liver cirrhosis development, induced by carbon tetrachloride,
and its prevention/treatment by natural compounds with antioxidant
and immune stimulating action. Studies were made on Wister rats,
weighing 120~140 g. Grape seeds extracts, separately and in
combination with well-known anticirrhotic drug ursodeoxycholic
acid (Urdoxa), have demonstrated effectiveness in prevention of liver
cirrhosis development and its treatment.
Abstract: Preparation of nanoparticles of cerium oxide and
adsorption of bovine serum albumin on them were studied. Particle
size distribution and influence of pH on zeta potential of prepared
CeO2 were determined. Average size of prepared cerium oxide
nanoparticles was 9 nm. The simultaneous measurements of the
bovine serum albumin adsorption and zeta potential determination of
the (adsorption) suspensions were carried out. The adsorption
isotherms were found to be of typical Langmuir type; values of the
bovine serum albumin adsorption capacities were calculated.
Increasing of pH led to decrease of zeta potential and decrease of
adsorption capacity of cerium oxide nanoparticles. The maximum
adsorption capacity was found for strongly acid suspension (am =
118 mg/g). The samples of nanoceria with positive zeta potential
adsorbed more bovine serum albumin on the other hand, the samples
with negative zeta potential showed little or no protein adsorption.
Surface charge or better say zeta potential of CeO2 nanoparticles
plays the key role in adsorption of proteins on such type of materials.
Abstract: Esterification of p-bromo-m-cresol led to formation of
2-(4-bromo-3-methylphenoxy)acetate (1). 2-(4-Bromo-3-methyl
phenoxy)acetohydrazide (2) is derived from Compound (1) by
hydrazination. Compound (2) was reacted with different aromatic
aldehydes to yield N-(substituted benzylidiene)-2-(4-bromo-3-methyl
phenoxy)acetamide(3a-c). Cyclization of compound (3a-c) with
thioglycolic acid yielded 2-(4-bromo-3-methylphenoxy)-N-(4-oxo-2-
arylthiazolidin-3-yl) acetamide (4a-c). The newly synthesized
compounds were characterized on the basis of spectral studies and
evaluated for antibacterial and antifungal activities.
Abstract: Kigelia africana (Lam.) Benth. (Bignoniaceae) is a
reputed traditional remedy for various human ailments such as skin
diseases, microbial infections, melanoma, stomach troubles,
metabolic disorders, malaria and general pains. In spite of the fruit
being widely used for purposes related to its antibacterial and
antifungal properties, the chemical constituents associated with the
activity have not been fully identified. To elucidate the active
principles, we evaluated the antimicrobial activity of fruit extracts
and purified fractions against Staphylococcus aureus, Enterococcus
faecalis, Moraxella catarrhalis, Escherichia coli, Candida albicans
and Candida tropicalis. Shade-dried fruits were powdered and
extracted with hydroalcoholic (1:1) mixture by soaking at room
temperature for 72 h. The crude extract was further fractionated by
column chromatography, with successive elution using hexane,
dichloromethane, ethyl acetate, acetone and methanol. The
dichloromethane and ethyl acetate fractions were combined and
subjected to column chromatography to furnish a wax and oil from
the eluates of 20% and 40% ethyl acetate in hexane, respectively. The
GC-MS and GC×GC-MS results revealed that linoleic acid, linolenic
acid, palmitic acid, arachidic acid and stearic acid were the major
constituents in both oil and wax. The crude hydroalcoholic extract
exhibited the strongest activity with MICs of 0.125-0.5 mg/mL,
followed by the ethyl acetate (MICs = 0.125-1.0 mg/mL),
dichloromethane (MICs = 0.250-2.0 mg/mL), hexane (MICs = 0.25-
2.0 mg/mL), acetone (MICs = 0.5-2.0 mg/mL) and methanol (MICs =
1.0-2.0 mg/mL), whereas the wax (MICs = 2.0-4.0 mg/mL) and oil
(MICs = 4.0-8.0 mg/mL) showed poor activity. The study concludes
that synergistic interactions of chemical constituents could be
responsible for the antimicrobial activity of K. africana fruits, which
needs a more holistic approach to understand the mechanism of its
antimicrobial activity.
Abstract: Folic acid (FA) is known to be an important
supplement to prevent neural tube defect (NTD) in pregnant women.
Similar to some commercial formulations, sodium bicarbonate
solution is used as a solvent for FA. This work uses the antisolvent
vapour precipitation (AVP), incorporating ethanol vapour as the
convective drying medium in place of air to produce branch-like
micro-structure FA particles. Interestingly, the dissolution rate of the
resultant particle is 2-3 times better than the particle produce from
conventional air drying due to the higher surface area of particles
produced. The higher dissolution rate could possibly improve the
delivery and absorption of FA in human body. This application could
potentially be extended to other commercial products, particularly in
less soluble drugs to improve its solubility.
Abstract: In this paper, snow samples containing dust particles
from several sampling points around the city of Ostrava were
analyzed. The pH values of sampled snow were measured and solid
particles analyzed. Particle size, zeta potential and content of selected
heavy metals were determined in solid particles. The pH values of
most samples lay in the slightly acid region. Mean values of particle
size ranged from 290.5 to 620.5 nm. Zeta potential values varied
between -5 and -26.5 mV. The following heavy metal concentration
ranges were found: copper 0.08-0.75 mg/g, lead 0.05-0.9 mg/g,
manganese 0.45-5.9 mg/g and iron 25.7-280.46 mg/g. The highest
values of copper and lead were found in the vicinity of busy
crossroads, and on the contrary, the highest levels of manganese and
iron were detected close to a large steelworks. The proportion
between pH values, zeta potentials, particle sizes and heavy metal
contents was established. Zeta potential decreased with rising pH
values and, simultaneously, heavy metal content in solid particles
increased. At the same time, higher metal content corresponded to
lower particle size.
Abstract: This paper involved the performance of a hightemperature
X-Ray powder diffraction analysis (XRD) of a sample of
chemical gypsum generated in the production of titanium white; this
gypsum originates by neutralizing highly acidic water with limestone
suspension. Specifically, it was gypsum formed in the first stage of
neutralization when the resulting material contains, apart from
gypsum, a number of waste products resulting from the
decomposition of ilmenite by sulphuric acid. So it can be described as
red titanogypsum. By conducting the experiment using XRD
apparatus Bruker D8 Advance with a Cu anode (λkα=1.54184 Å)
equipped with high-temperature chamber Anton Paar HTK 16, it was
possible to identify clearly in the sample each phase transition in the
system of CaSO4·xH2O.
Abstract: The objective of the study was to select the survival of
probiotic strains when exposed to acidic and bile salts condition. Four
probiotic strains Lactobacillus casei subsp. rhamnosus TISTR 047,
Lactobacillus casei TISTR 1500, Lactobacillus acidophilus TISTR
1338 and Lactobacillus plantarum TISTR 1465 were cultured in
MRS broth and incubated at 35ºC for 15 hours before being inoculated
into acidic condition 5 M HCl, pH 2 for 2 hours and bile salt 0.3%,
pH 5.8 for 8 hour. The survived probiotics were counted in MRS agar.
Among four stains, Lactobacillus casei subsp. rhamnosus TISTR 047
was the highest tolerance specie. Lactobacillus casei subsp.
rhamnosus TISTR 047 reduced 6.74±0.07 log CFU/ml after growing
in acid and 5.52±0.05 log CFU/ml after growing in bile salt. Then,
double emulsion of microorganisms was chosen to encapsulate before
spray drying. Spray drying was done with the inlet temperature 170ºC
and outlet temperature 80ºC. The results showed that the survival of
encapsulated Lactobacillus casei subsp. rhamnosus TISTR 047 after
spray drying decreased from 9.63 ± 0.32 to 8.31 ± 0.11 log CFU/ml
comparing with non-encapsulated, 9.63 ± 0.32 to 4.06 ± 0.08 log
CFU/ml. Therefore, Lactobacillus casei subsp. rhamnosus TISTR 047
would be able to survive in gastrointestinal and spray drying condition.
Abstract: This article presents summary on preparation and
characterization of zinc, copper, cadmium and cobalt chromite
nanocrystals, embedded in an amorphous silica matrix. The
ZnCr2O4/SiO2, CuCr2O4/SiO2, CdCr2O4/SiO2 and CoCr2O4/SiO2
nanocomposites were prepared by a conventional sol-gel method
under acid catalysis. Final heat treatment of the samples was carried
out at temperatures in the range of 900−1200 ◦C to adjust the
phase composition and the crystallite size, respectively. The resulting
samples were characterized by Powder X-ray diffraction (PXRD),
High Resolution Transmission Electron Microscopy (HRTEM),
Raman/FTIR spectroscopy and magnetic measurements. Formation
of the spinel phase was confirmed in all samples. The average size of
the nanocrystals was determined from the PXRD data and by direct
particle size observation on HRTEM; both results were correlated.
The mean particle size (reviewed by HRTEM) was in the range from
∼4 to 46 nm. The results showed that the sol-gel method can be
effectively used for preparation of the spinel chromite nanoparticles
embedded in the silica matrix and the particle size is driven by the
type of the cation A2+ in the spinel structure and the temperature
of the final heat treatment. Magnetic properties of the nanocrystals
were found to be just moderately modified in comparison to the bulk
phases.
Abstract: Heavy metals are one of the major groups of
contaminants in the environment and many of them are toxic even at
very low concentration in plants and animals. However, some metals
play important roles in the biological function of many enzymes in
living organisms. Metals such as zinc, iron, and cooper are important
for survival and activity of enzymes in plants, however heavy metals
can inhibit enzyme which is responsible for defense system of plants.
Polyphenol oxidase (PPO) is a copper-containing metalloenzyme
which is responsible for enzymatic browning reaction of plants.
Enzymatic browning is a major problem for the handling of
vegetables and fruits in food industry. It can be increased and
effected with many different futures such as metals in the nature and
ground. In the present work, PPO was isolated and characterized
from green leaves of red poppy plant (Papaverr hoeas). Then, the
effect of some known antibrowning agents which can form
complexes with metals and metals were investigated on the red poppy
PPO activity. The results showed that glutathione was the most
potent inhibitory effect on PPO activity. Cu(II) and Fe(II) metals
increased the enzyme activities however, Sn(II) had the maximum
inhibitory effect and Zn(II) and Pb(II) had no significant effect on the
enzyme activity. In order to reduce the effect of heavy metals, the
effects of metal-antibrowning agent complexes on the PPO activity
were determined. EDTA and metal complexes had no significant
effect on the enzyme. L-ascorbic acid and metal complexes decreased
but L-ascorbic acid-Cu(II)-complex had no effect. Glutathione–metal
complexes had the best inhibitory effect on Red poppy leaf PPO
activity.
Abstract: The aim of the present study is to investigate the
potential use of the selected seed oils. The oil was extracted using
Soxhlet apparatus and the physicochemical characteristics of the oil
determined using standard methods. The following results were
obtained for the physicochemical parameters analysed: for Egusi seed
oil, Oil yield 53.20%, Saponification value 178.03±1.25 mgKOH/g,
Iodine value 49.10±0.32 g I2/100g, Acid value 4.30±0.86 mgKOH/g,
and Peroxide value 5.80±0.27 meq/kg were obtained. For Pawpaw
seed oil, Oil yield 40.10%, Saponification value 24.13±3.93
mgKOH/g, Iodine value 24.87±0.19 g I2/100g, Acid value 9.46±0.40
mgKOH/g, and Peroxide value 3.12±1.22 meq/kg were obtained. For
Sweet orange seed oil, Oil yield 43.10%, Saponification value
106.30±2.37 mgKOH/g, Iodine value 37.08±0.04 g I2/100g, Acid
value 7.59±0.77 mgKOH/g, and Peroxide value 2.21±0.46 meq/kg
were obtained. From the obtained values of the determined
parameters, the oils can be extracted from the three selected seeds in
commercial quantities and that the egusi and sweet orange seed oils
may be utilized in the industrial soap production.
Abstract: The lactic acid bacteria (LAB) were isolated from
10 samples of fermented foods (Sa-tor-dong and Bodo) in South
locality of Thailand. The 23 isolates of lactic acid bacteria were
selected, which were exhibited a clear zone and growth on MRS
agar supplemented with CaCO3. All of lactic acid bacteria were
tested on morphological and biochemical. The result showed that
all isolates were Gram’s positive, non-spore forming but only
10 isolates displayed catalase negative. The 10 isolates including
BD1 .1, BD 1.2, BD 2.1, BD2.2, BD 2.3, BD 3.1, BD 4.1, BD 5.2,
ST 4.1 and ST 5.2 were selected for inhibition activity
determination. Only 2 strains (ST 4.1 and BD 2.3) showed
inhibition zone on agar, when using Escherichia coli sp. as target
strain. The ST 4.1 showed highest inhibition zone on agar, which
was selected for probiotic property testing. The ST4.1 isolate
could grow in MRS broth containing a high concentration of
sodium chloride 6%, bile salts 7%, pH 4-10 and vary temperature
at 15-45°C.
Abstract: With demand for primary energy continuously
growing, search for renewable and efficient energy sources has been
high on agenda of our society. One of the most promising energy
sources is biogas technology. Residues coming from dairy industry
and milk processing could be used in biogas production; however,
low efficiency and high cost impede wide application of such
technology. One of the main problems is management and conversion
of organic residues through the anaerobic digestion process which is
characterized by acidic environment due to the low whey pH (
Abstract: Voltage sags are the most common power quality
disturbance in the distribution system. It occurs due to the fault in the
electrical network or by the starting of a large induction motor and
this can be solved by using the custom power devices such as
Dynamic Voltage Restorer (DVR). In this paper DVR is proposed to
compensate voltage sags on critical loads dynamically. The DVR
consists of VSC, injection transformers, passive filters and energy
storage (lead acid battery). By injecting an appropriate voltage, the
DVR restores a voltage waveform and ensures constant load voltage.
The simulation and experimental results of a DVR using MATLAB
software shows clearly the performance of the DVR in mitigating
voltage sags.
Abstract: Boron-gypsum is a waste which occurs in the boric
acid production process. In this study, the boron content of this waste
is evaluated for the use in synthesis of magnesium borates and such
evaluation of this kind of waste is useful more than storage or
disposal. Magnesium borates, which are a sub-class of boron
minerals, are useful additive materials for the industries due to their
remarkable thermal and mechanical properties. Magnesium borates
were obtained hydrothermally at different temperatures. Novelty of
this study is the search of the solution density effects to magnesium
borate synthesis process for the increasing the possibility of borongypsum
usage as a raw material. After the synthesis process, products
are subjected to XRD and FT-IR to identify and characterize their
crystal structure, respectively.
Abstract: Enzyme activity was evaluated in the intestine of
juvenile dourado (Salminus brasiliensis) fed with diets containing 0,
10 or 20% of lyophilized bovine colostrum (LBC) inclusion for either
30 or 60 days. The intestinal enzymes acid and alkaline phosphatase
(ACP and ALP, respectively), non-specific esterase (NSE), lipase
(LIP), dipeptidyl aminopeptidase IV (DAP IV) and leucine
aminopeptidase (LAP) were studied using histochemistry in four
intestinal segments (S1, S2, S3 and posterior intestine). Weak
proteolitic activity was observed in all intestinal segments for DAP
IV and LAP. The activity of NSE and LIP was also weak in all
intestines, except for the moderate activity of NSE in the S2 of 20%
LBC group after 30 days and in the S1 of 0% LBC group after 60
days. The ACP was detected only in the S2 and S3 of the 10% LBC
group after 30 days. Moderate and strong staining was observed in
the first three intestinal segments for ALP and weak activity in the
posterior intestine. The activity of DAP IV, LAP and ALP were also
present in the cytoplasm of the enterocytes. In the present results,
bovine colostrum feeding did not cause alterations in activity of
intestinal enzymes.
Abstract: Amyloid aggregation of polypeptides is related to a
growing number of pathologic states known as amyloid disorders. In
recent years, blocking or reversing amyloid aggregation via the use of
small compounds are considered as two useful approaches in
hampering the development of these diseases. In this research, we
have compared the ability of several manganese-salen derivatives, as
synthetic compounds, and apigenin, as a natural flavonoid, to inhibit
of hen egg-white lysozyme (HEWL) aggregation, as an in vitro
model system.
Different spectroscopic analyses such as Thioflavin T (ThT) and
Anilinonaphthalene-8-sulfonic acid (ANS) fluorescence, Congo red
(CR) absorbance along with transmission electron microscopy were
used in this work to monitor the HEWL aggregation kinetic and
inhibition. Our results demonstrated that both type of compounds
were capable to prevent the formation of lysozyme amyloid
aggregation in vitro. In addition, our data indicated that synthetic
compounds had higher activity to inhibit of the β-sheet structures
relative to natural compound. Regarding the higher antioxidant
activities of the salen derivatives, it can be concluded that in addition
to aromatic rings of each of the compounds, the potent antioxidant
properties of salen derivatives contributes to lower lysozyme fibril
accumulation.
Abstract: Ion exchange is one of the methods used to remove heavy metal such as copper and cobalt from wastewaters. Parameters affecting the ion-exchange of copper and cobalt aqueous solutions using clinoptilolite are the objectives of this study. Synthetic solutions were prepared with the concentration of 0.02M, 0.06M and 0.1M. The cobalt solution was maintained to 0.02M while varying the copper solution to the above stated concentrations. The clinoptilolite was activated with HCl and H2SO4 for removal efficiency. The pHs of the solutions were found to be acidic hence enhancing the copper and cobalt removal. The natural clinoptilolite performance was also found to be lower compared to the HCl and H2SO4 activated one for the copper removal ranging from 68% to 78% of Cu2+ uptake with the natural clinoptilolite to 66% to 51% with HCl and H2SO4 respectively. It was found that the activated clinoptilolite removed more copper and cobalt than the natural one and found that the electronegativity of the metal plays a role in the metal removal and the clinoptilolite selectivity.