Abstract: The present work describes the implementation of the
Enhanced Collaborative Optimization (ECO) multilevel architecture
with a gradient-based optimization algorithm with the aim of
performing a multidisciplinary design optimization of a generic
unmanned aerial vehicle with morphing technologies. The concepts
of weighting coefficient and dynamic compatibility parameter are
presented for the ECO architecture. A routine that calculates the
aircraft performance for the user defined mission profile and vehicle’s
performance requirements has been implemented using low fidelity
models for the aerodynamics, stability, propulsion, weight, balance
and flight performance. A benchmarking case study for evaluating
the advantage of using a variable span wing within the optimization
methodology developed is presented.
Abstract: The dissimilar joint between aluminum/titanium
alloys (Al 6082 and Ti G2) were successfully achieved by CO2 laser
welding with a single pass and without filler material using the
overlap joint design. Laser welding parameters ranges combinations
were experimentally determined using Taguchi approach with the
objective of producing welded joint with acceptable welding profile
and high quality of mechanical properties. In this study a joining of
dissimilar Al 6082 / Ti G2 was resulted in three distinct regions
fusion area in the weldment. These regions are studied in terms of its
microstructural characteristics and microhardness which are directly
affecting the welding quality.
The weld metal was mainly composed of martensite alpha prime.
In two different metals in the two different sides of joint HAZ, grain
growth was detected. The microhardness of the joint distribution also
has shown microhardness increasing in the HAZ of two base metals
and a varying microhardness in fusion zone.
Abstract: In this study, we compare the profiles of transitory
hybrid entrepreneurs and persistent hybrid entrepreneurs to determine
how they differ. Hybrid entrepreneurs (HEs) represent a significant
share of entrepreneurial activity yet little is known about them. We
define HEs as individuals who are active as entrepreneurs but do no
support themselves primarily by their enterprise. Persistent HEs
(PHEs) are not planning to transition to fulltime entrepreneurship
whereas transitory HEs (THEs) consider it probable. Our results
show that THEs and PHEs are quite similar in background. THEs are
more interested in increasing their turnover than PHEs, as expected,
but also emphasize self-fulfillment as a motive for entrepreneurship
more than PHEs. The clearest differences between THEs and PHEs
are found in their views on how well their immediate circle supports
full-time entrepreneurship, and their views of their own
entrepreneurial abilities and the market potential of their firm. Our
results support earlier arguments that hybrids should be considered
separately in research on entrepreneurial entry and self-employment.
Abstract: Iron is an essential nutrient with limited
bioavailability. Nutritional anemia caused mainly by iron deficiency
is the most recognized nutritional problem in both countries as well
as affluent societies. Rice (Oryza sativa L.) has become the most
important cereal crop for the improvement of human health due to the
starch, protein, oil, and the majority of micronutrients, particularly in
Asian countries. In this study, the iron availability and profile lipid
were evaluated for the extracts from Cibeusi varieties (black rices) of
ancient rice brans.
Results: The quality of K, B, R, E diets groups shows the same
effect on the growth of rats. Hematocrit and MCHC levels of rats fed
K, B, R and E diets were not significantly (P
Abstract: This research was conducted in the Mae Sot
Watershed where located in the Moei River Basin at the Upper
Salween River Basin in Tak Province, Thailand. The Mae Sot
Municipality is the largest urban area in Tak Province and situated in
the midstream of the Mae Sot Watershed. It usually faces flash flood
problem after heavy rain due to poor flood management has been
reported since economic rapidly bloom up in recent years. Its
catchment can be classified as ungauged basin with lack of rainfall
data and no any stream gaging station was reported. It was attached
by most severely flood events in 2013 as the worst studied case for
all those communities in this municipality. Moreover, other problems
are also faced in this watershed, such shortage water supply for
domestic consumption and agriculture utilizations including a
deterioration of water quality and landslide as well. The research
aimed to increase capability building and strengthening the
participation of those local community leaders and related agencies to
conduct better water management in urban area was started by mean
of the data collection and illustration of the appropriated application
of some short period rainfall forecasting model as they aim for better
flood relief plan and management through the hydrologic model
system and river analysis system programs. The authors intended to
apply the global rainfall data via the integrated data viewer (IDV)
program from the Unidata with the aim for rainfall forecasting in a
short period of 7-10 days in advance during rainy season instead of
real time record. The IDV product can be present in an advance
period of rainfall with time step of 3-6 hours was introduced to the
communities. The result can be used as input data to the hydrologic
modeling system model (HEC-HMS) for synthesizing flood
hydrographs and use for flood forecasting as well. The authors
applied the river analysis system model (HEC-RAS) to present flood
flow behaviors in the reach of the Mae Sot stream via the downtown
of the Mae Sot City as flood extents as the water surface level at
every cross-sectional profiles of the stream. Both models of HMS and
RAS were tested in 2013 with observed rainfall and inflow-outflow
data from the Mae Sot Dam. The result of HMS showed fit to the
observed data at the dam and applied at upstream boundary discharge
to RAS in order to simulate flood extents and tested in the field, and
the result found satisfying. The product of rainfall from IDV was fair
while compared with observed data. However, it is an appropriate
tool to use in the ungauged catchment to use with flood hydrograph
and river analysis models for future efficient flood relief plan and
management.
Abstract: This paper describes the tradeoffs and the design from
scratch of a self-contained, easy-to-use health dashboard software
system that provides customizable data tracking for patients in smart
homes. The system is made up of different software modules and
comprises a front-end and a back-end component. Built with HTML,
CSS, and JavaScript, the front-end allows adding users, logging into
the system, selecting metrics, and specifying health goals. The backend
consists of a NoSQL Mongo database, a Python script, and a
SimpleHTTPServer written in Python. The database stores user
profiles and health data in JSON format. The Python script makes use
of the PyMongo driver library to query the database and displays
formatted data as a daily snapshot of user health metrics against
target goals. Any number of standard and custom metrics can be
added to the system, and corresponding health data can be fed
automatically, via sensor APIs or manually, as text or picture data
files. A real-time METAR request API permits correlating weather
data with patient health, and an advanced query system is
implemented to allow trend analysis of selected health metrics over
custom time intervals. Available on the GitHub repository system,
the project is free to use for academic purposes of learning and
experimenting, or practical purposes by building on it.
Abstract: Various personality profile tests are used to identify
personality strengths and limits in individuals, helping both
individuals and managers to optimize work and team effort in
organizations. One such test, the Hartman’s personality profile,
emphasizes four driving "core motives" influenced or affected by
both strengths and limitations classified into four colors: Red -
motivated by power; Blue - discipline and loyalty; White - peace; and
Yellow – fun loving. Two shortcomings of Hartman’s personality test
are noted; 1) only one selection for every item / situation allowed and
2) selection of an item / option even if not applicable. A test taker
may be as much nurturing as he is opinionated but since
“opinionated” seems less attractive the individual would likely select
nurturing, causing a misidentification in personality strengths and
limits. Since few individuals have a “strong” personality, it is
difficult to assess their true personality strengths and limits allowing
only one choice or requiring unwanted choices, undermining the
potential of the test. We modified Hartman’s personality profile
allowing test takers to make either multiple choices for any item /
situation or leave them blank if applicable. Sixty-eight participants
(38 males and 30 females), 17 - 49 years old, from countries in Asia,
Europe, N. America, CIS, Africa, Latin America, and Oceania were
included. 58 participants (85.3%) reported the modified test, allowing
multiple / no choices better identified their personality strengths and
limits, while 10 participants (14.7%) expressed the original (one
choice version) was sufficient. The overall results show that our
modified test enhanced the identification and balance of core
personalities’ strengths and limits, aiding test takers, managers and
organizations to better assess individual characteristics, particularly
useful in making task-related, teamwork, and management decisions.
Abstract: A compact UWB planar antenna fed with a
microstrip-line is proposed. The new design consist of a rectangular
patch with symmetric l-shaped slots and fed by 50 Ω microstrip
transmission line and a reduced ground-plane which have a periodic
slots with an overall size of 47 mm x 20 mm. It is intended to be used
in wireless applications that cover the ultra-wideband (UWB)
frequency band. A wider impedance bandwidth of around 116.5%
(1.875 – 7.115 GHz) with stable radiation pattern is achieved. The
proposed antenna has excellent characteristics, low profile and costeffective
compared to existing UWB antennas. The UWB antenna is
designed and analyzed using CST Microwave Studio in transient
mode to verify antenna parameters improvements.
Abstract: The industrial process adds to engineering wood
products features absent in solid wood, with homogeneous structure
and reduced defects, improved physical and mechanical properties,
bio-deterioration, resistance and better dimensional stability,
improving quality and increasing the reliability of structures wood.
These features combined with using fast-growing trees, make them
environmentally ecological products, ensuring a strong consumer
market. The wood I-joists are manufactured by the industrial profiles
bonding flange and web, an important aspect of the production of
wooden I-beams is the adhesive joint that bonds the web to the
flange. Adhesives can effectively transfer and distribute stresses,
thereby increasing the strength and stiffness of the composite. The
objective of this study is to evaluate different resins in a shear strain
specimens with the aim of analyzing the most efficient resin and
possibility of using national products, reducing the manufacturing
cost. First was conducted a literature review, where established the
geometry and materials generally used, then established and analyzed
8 national resins and produced six specimens for each.
Abstract: In this paper, the improvement by deconvolution of
the depth resolution in Secondary Ion Mass Spectrometry (SIMS)
analysis is considered. Indeed, we have developed a new Tikhonov-
Miller deconvolution algorithm where a priori model of the solution
is included. This is a denoisy and pre-deconvoluted signal obtained
from: firstly, by the application of wavelet shrinkage algorithm,
secondly by the introduction of the obtained denoisy signal in an
iterative deconvolution algorithm. In particular, we have focused the
light on the effect of the iterations number on the evolution of the
deconvoluted signals. The SIMS profiles are multilayers of Boron in
Silicon matrix.
Abstract: Vancron 40, a nitrided powder metallurgical tool
Steel, is used in cold work applications where the predominant failure
mechanisms are adhesive wear or galling. Typical applications of
Vancron 40 are among others fine blanking, cold extrusion, deep
drawing and cold work rolls for cluster mills. Vancron 40 positive
results for cold work rolls for cluster mills and as a tool for some
severe metal forming process makes it competitive compared to other
type of work rolls that require higher precision, among others in cold
rolling of thin stainless steel, which required high surface finish
quality. In this project, three roll materials for cold rolling of stainless
steel strip was examined, Vancron 40, Narva 12B (a high-carbon,
high-chromium tool steel alloyed with tungsten) and Supra 3 (a
Chromium-molybdenum tungsten-vanadium alloyed high speed
steel). The purpose of this project was to study the depth profiles of
the ironed stainless steel strips, emergence of galling and to study the
lubrication performance used by steel industries. Laboratory
experiments were conducted to examine scratch of the strip, galling
and surface roughness of the roll materials under severe tribological
conditions. The critical sliding length for onset of galling was
estimated for stainless steel with four different lubricants. Laboratory
experiments result of performance evaluation of resistance capability
of rolls toward adhesive wear under severe conditions for low and
high reductions. Vancron 40 in combination with cold rolling
lubricant gave good surface quality, prevents galling of
metal surfaces and good bearing capacity.
Abstract: Some regularities of formation of a new structural
state of the thermoplastic polymers - gradually oriented (stretched)
state (GOS) are discussed. Transition into GOS is realized by the
graded oriented stretching - by action of inhomogeneous mechanical
field on the isotropic linear polymers or by zone stretching that is
implemented on a standard tensile-testing machine with using a
specially designed zone stretching device (ZSD). Both technical
approaches (especially zone stretching method) allows to manage the
such quantitative parameters of gradually oriented polymers as a
range of change in relative elongation/orientation degree, length of
this change and profile (linear, hyperbolic, parabolic, logarithmic,
etc.). The possibility of obtaining functionally graded materials
(FGMs) by graded orientation method is briefly discussed. Uniaxial
graded stretching method should be considered as an effective
technological solution to create polymer materials with a
predetermined gradient of physical properties.
Abstract: Risperidone (RISP) is an antipsychotic agent and has
low water solubility and nontargeted delivery results in numerous
side effects. Hence, an attempt was made to develop SLNs hydrogel
for intranasal delivery of RISP to achieve maximum bioavailability
and reduction of side effects. RISP loaded SLNs composed of 1.65%
(w/v) lipid mass were produced by high shear homogenization (HSH)
coupled ultrasound (US) method using glycerylmonostearate (GMS)
or Imwitor 900K (solid lipid). The particles were loaded with 0.2%
(w/v) of the RISP & surface-tailored with a 2.02% (w/v) non-ionic
surfactant Tween® 80. Optimization was done using 32 factorial
design using Design Expert® software. The prepared SLNs
dispersion incorporated into Polycarbophil AA1 hydrogel (0.5%
w/v). The final gel formulation was evaluated for entrapment
efficiency, particle size, rheological properties, X ray diffraction, in
vitro diffusion, ex vivo permeation using sheep nasal mucosa and
histopathological studies for nasocilliary toxicity. The entrapment
efficiency of optimized SLNs was found to be 76 ± 2%,
polydispersity index
Abstract: The present study was done to evaluate the presence
of tetracycline resistance genes in Lactococcus garvieae isolated
from cultured rainbow trout, West Iran. The isolates were examined
for antimicrobial resistance using disc diffusion method. Of the 49
strains tested, 19 were resistant to tetracycline (38.7%), 32 to
enrofloxacin (65.3%), 21 to erythromycin (42.8%), 20 to
chloramphenicol and trimetoprim-sulfamethoxazole (40.8%). The
strains were then characterized for their genotypic resistance profiles.
The results revealed that all 49 isolates contained at least one of the
tetracycline resistance genes. Tet (A) was found in 89.4% of
tetracycline resistant isolates and the frequency of other gene were as
follows: tet (E) 42.1%, tet (B) 47.3%, tet (D) 15.7%, tet (L) 26.3%,
tet (K) 52.6%, tet (G) 36.8%, tet (34) 21%, tet (S) 63.1%, tet (C)
57.8%, tet (M) 73.6%, tet (O) 42.1%. The results revealed high levels
of antibiotic resistance in L. garvieae strains which is a potential
danger for trout culture as well as for public health.
Abstract: In this paper, effect of marginal quality groundwater
on yield of cotton crop and soil salinity was studied. In this
connection, three irrigation treatments each with four replications
were applied. These treatments were i) use of canal water (T1), ii) use
of marginal quality groundwater from tubewell (T2), and iii)
conjunctive use by mixing with the ratio of 1:1 of canal water and
marginal quality tubewell water (T3).
Water was applied to the crop cultivated in Kharif season 2011; its
quantity has been measured using cut-throat flume. Total 11 watering
each of 50 mm depth have been applied from 20th April to 20th July,
2011. Further, irrigations were stopped due to monsoon rainfall up to
crop harvesting.
Maximum crop yield (seed cotton) was observed under T1 which
was 1,517 kg/ha followed by T3 (mixed canal and tubewell water)
having 1009 kg/ha and T2 i.e. marginal quality groundwater having
709 kg/ha. This concludes that crop yield in T2 and T3 in comparison
to T1was reduced by about 53 and 30% respectively.
It has been observed that yield of cotton crop is below potential
limit for three treatments due to unexpected rainfall at the time of full
flowering season; thus the yield was adversely affected.
However, salt deposition in soil profiles was not observed that is
due to leaching effect of heavy rainfall occurred during monsoon
season.
Abstract: The study is devoted to define the optimal conditions
for the nitriding of pure iron at atmospheric pressure by using NH3-
Ar-C3H8 gas mixtures. After studying the mechanisms of phase
formation and mass transfer at the gas-solid interface, a mathematical
model is developed in order to predict the nitrogen transfer rate in the
solid, the ε-carbonitride layer growth rate and the nitrogen and
carbon concentration profiles. In order to validate the model and to
show its possibilities, it is compared with thermogravimetric
experiments, analyses and metallurgical observations (X-ray
diffraction, optical microscopy and electron microprobe analysis).
Results obtained allow us to demonstrate the sound correlation
between the experimental results and the theoretical predictions.
Abstract: The effect of a 3-dimensional (3D) blade on the turbine
characteristics of Wells turbine for wave energy conversion has been
investigated experimentally by model testing under steady flow
conditions in this study, in order to improve the peak efficiency and
stall characteristics. The aim of use of 3D blade is to prevent flow
separation on the suction surface near the tip. The chord length is
constant with radius and the blade profile changes gradually from the
mean radius to tip. The proposed blade profiles in the study are
NACA0015 from the hub to mean radius and NACA0025 at the tip.
The performances of Wells turbine with 3D blades has been compared
with those of the original Wells turbine, i.e., the turbine with
2-dimensional (2D) blades. As a result, it was concluded that although
the peak efficiency of Wells turbine can be improved by the use of the
proposed 3D blade, its blade does not overcome the weakness of
stalling.
Abstract: Two types of glass fibers having different lengths
(1/16" and 1/32") were added into rigid PVC foams to enhance the
dimensional stability of extruded rigid Polyvinyl Chloride (PVC)
foam at different concentrations (0-20 phr) using a single screw
profile extruder. PVC foam-glass fiber composites (PVC-GF) were
characterized for their dimensional stability, structural, thermal, and
mechanical properties. Experimental results show that the
dimensional stability, heat resistance, and storage modulus were
enhanced without compromising the tensile and flexural strengths of
the composites. Overall, foam composites which were prepared with
longer glass fibers exhibit better mechanical and thermal properties
than those prepared with shorter glass fibers due to higher
interlocking between the fibers and the foam cells, which result in
better load distribution in the matrix.
Abstract: Among modern airflow measurement methods,
Particle Image Velocimetry (PIV) and Particle Tracking Velocimetry
(PTV), as visualized and non-instructive measurement techniques, are
playing more important role. This paper conducts a comparative
experimental study for airflow measurement employing both
techniques with the same condition. Velocity vector fields, velocity
contour fields, voticity profiles and turbulence profiles are selected as
the comparison indexes. The results show that the performance of both
PIV and PTV techniques for airflow measurement is satisfied, but
some differences between the both techniques are existed, it suggests
that selecting the measurement technique should be based on a
comprehensive consideration.
Abstract: The financial crises caused a collapse in prices of
most asset classes, raising the attention on alternative investments
such as sukuk, a smaller, fast growing but often misunderstood
market. We study diversification benefits of sukuk, their correlation
with other asset classes and the effects of their inclusion in
investment portfolios of institutional and retail investors, through a
comprehensive comparison of their risk/return profiles during and
after the financial crisis.
We find a beneficial performance adjusted for the specific
volatility together with a lower correlation especially during the
financial crisis. The distribution of sukuk returns is positively skewed
and leptokurtic, with a risk/return profile similarly to high yield
bonds. Overall, our results suggest that sukuk present diversification
opportunities, a significant volatility-adjusted performance and lower
correlations especially during the financial crisis.
Our findings are relevant for a number of institutional investors.
Long term investors, such as life insurers would benefit from sukuk’s
protective features during financial crisis yet keeping return and
growth opportunities, whereas banks would gain due to their role of
placers, advisors, market makers or underwriters.