Abstract: For stricter drinking water regulations in the future, reducing the humic acid and disinfection byproducts in raw water, namely, trihalomethanes (THMs) and haloacetic acids (HAAs) is worthy for research. To investigate the removal of waterborne organic material using a lab-scale of bio-activated carbon filter under different EBCT, the concentrations of humic acid prepared were 0.01, 0.03, 0.06, 0.12, 0.17, 0.23, and 0.29 mg/L. Then we conducted experiments using a pilot plant with in-field of the serially connected bio-activated carbon filters and hollow fiber membrane processes employed in traditional water purification plants. Results showed under low TOC conditions of humic acid in influent (0.69 to 1.03 mg TOC/L) with an EBCT of 30 min, 40 min, and 50 min, TOC removal rates increases with greater EBCT, attaining about 39 % removal rate. The removal rate of THMs and HAAs by BACF was 54.8 % and 89.0 %, respectively.
Abstract: The bromination of five selected pharmaceuticals
(metoprolol, naproxen, amoxicillin, hydrochlorotiazide and
phenacetin) in ultrapure water and in three water matrices (a
groundwater, a surface water from a public reservoir and a secondary
effluent from a WWTP) was investigated. The apparent rate
constants for the bromination reaction were determined as a function
of the pH, and the sequence obtained for the reaction rate was
amoxicillin > naproxen >> hydrochlorotiazide ≈ phenacetin ≈
metoprolol. The proposal of a kinetic mechanism, which specifies the
dissociation of bromine and each pharmaceutical according to their
pKa values and the pH allowed the determination of the intrinsic rate
constants for every elementary reaction. The influence of the main
operating conditions (pH, initial bromine dose, and the water matrix)
on the degradation of pharmaceuticals was established. In addition,
the presence of bromide in chlorination experiments was
investigated. The presence of bromide in wastewaters and drinking
waters in the range of 10 to several hundred μg L-1 accelerated
slightly the oxidation of the selected pharmaceuticals during chorine
disinfection.
Abstract: The direct discharge of palm oil mill effluent (POME) wastewater causes serious environmental pollution due to its high chemical oxygen demand (COD) and biochemical oxygen demand (BOD). Traditional ways for POME treatment have both economical and environmental disadvantages. In this study, a membrane anaerobic system (MAS) was used as an alternative, cost effective method for treating POME. Six steady states were attained as a part of a kinetic study that considered concentration ranges of 8,220 to 15,400 mg/l for mixed liquor suspended solids (MLSS) and 6,329 to 13,244 mg/l for mixed liquor volatile suspended solids (MLVSS). Kinetic equations from Monod, Contois and Chen & Hashimoto were employed to describe the kinetics of POME treatment at organic loading rates ranging from 2 to 13 kg COD/m3/d. throughout the experiment, the removal efficiency of COD was from 94.8 to 96.5% with hydraulic retention time, HRT from 400.6 to 5.7 days. The growth yield coefficient, Y was found to be 0.62gVSS/g COD the specific microorganism decay rate was 0.21 d-1 and the methane gas yield production rate was between 0.25 l/g COD/d and 0.58 l/g COD/d. Steady state influent COD concentrations increased from 18,302 mg/l in the first steady state to 43,500 mg/l in the sixth steady state. The minimum solids retention time, which was obtained from the three kinetic models ranged from 5 to 12.3 days. The k values were in the range of 0.35 – 0.519 g COD/ g VSS • d and values were between 0.26 and 0.379 d-1. The solids retention time (SRT) decreased from 800 days to 11.6 days. The complete treatment reduced the COD content to 2279 mg/l equivalent to a reduction of 94.8% reduction from the original.
Abstract: A method of dynamic mesh based airfoil optimization is proposed according to the drawbacks of surrogate model based airfoil optimization. Programs are designed to achieve the dynamic mesh. Boundary condition is add by integrating commercial software Pointwise, meanwhile the CFD calculation is carried out by commercial software Fluent. The data exchange and communication between the software and programs referred above have been accomplished, and the whole optimization process is performed in iSIGHT platform. A simplified airfoil optimization study case is brought out to show that aerodynamic performances of airfoil have been significantly improved, even save massive repeat operations and increase the robustness and credibility of the optimization result. The case above proclaims that dynamic mesh based airfoil optimization is an effective and high efficient method.
Abstract: Biological treatment of secondary effluent wastewater
by two combined denitrification/oxic filtration systems packed with
Lock type(denitrification filter) and ceramic ball (oxic filter) has been
studied for 5months. Two phases of operating conditions were carried
out with an influent nitrate and ammonia concentrations varied from
5.8 to 11.7mg/L and 5.4 to 12.4mg/L,respectively.
Denitrification/oxic filter treatment system were operated under an
EBCT (Empty Bed Contact Time) of 4h at system recirculation ratio in
the range from 0 to 300% (Linear Velocity increased 19.5m/d to
78m/d). The system efficiency of denitrification , nitrification over
95% respectively. Total nitrogen and COD removal range from
54.6%(recirculation 0%) to 92.3%(recirculation 300%) and 10% to
62.5%, respectively.
Abstract: Young people have a high prevalence of mental health
problems, yet tend not to seek help. Trusted adults in young people-s
lives, such as teachers and sports coaches, can make a major positive
contribution to the mental health of young people. Teachers and
sports coaches may be in a position to be effective in supporting
young people-s mental health through promotion, prevention and
early intervention. This study reports findings from interviews with
21 teachers and 13 sports coaches of young people aged 12 to 18 in
Canberra, Australia, regarding their perceptions of the relevance and
effectiveness of their role in supporting young people-s mental
health. Both teachers and coaches perceived having influential but
slightly different roles to play in supporting mental health. There may
be potential to elevate the influence of teachers and coaches as
sources of support for young people and their mental health care.
Abstract: Water hyacinth has been used in aquatic systems for
wastewater purification in many years worldwide. The role of water
hyacinth (Eichhornia crassipes) species in polishing nitrate and
phosphorus concentration from municipal wastewater treatment plant
effluent by phytoremediation method was evaluated. The objective
of this project is to determine the removal efficiency of water
hyacinth in polishing nitrate and phosphorus, as well as chemical
oxygen demand (COD) and ammonia. Water hyacinth is considered
as the most efficient aquatic plant used in removing vast range of
pollutants such as organic matters, nutrients and heavy metals. Water
hyacinth, also referred as macrophytes, were cultivated in the
treatment house in a reactor tank of approximately 90(L) x 40(W) x
25(H) in dimension and built with three compartments. Three water
hyacinths were placed in each compartments and water sample in
each compartment were collected in every two days. The plant
observation was conducted by weight measurement, plant uptake and
new young shoot development. Water hyacinth effectively removed
approximately 49% of COD, 81% of ammonia, 67% of phosphorus
and 92% of nitrate. It also showed significant growth rate at starting
from day 6 with 0.33 shoot/day and they kept developing up to 0.38
shoot/day at the end of day 24. From the studies conducted, it was
proved that water hyacinth is capable of polishing the effluent of
municipal wastewater which contains undesirable amount of nitrate
and phosphorus concentration.
Abstract: Circle grid space filling plate is a flow conditioner with a fractal pattern and used to eliminate turbulence originating from pipe fittings in experimental fluid flow applications. In this paper, steady state, incompressible, swirling turbulent flow through circle grid space filling plate has been studied. The solution and the analysis were carried out using finite volume CFD solver FLUENT 6.2. Three turbulence models were used in the numerical investigation and their results were compared with the pressure drop correlation of BS EN ISO 5167-2:2003. The turbulence models investigated here are the standard k-ε, realizable k-ε, and the Reynolds Stress Model (RSM). The results showed that the RSM model gave the best agreement with the ISO pressure drop correlation. The effects of circle grids space filling plate thickness and Reynolds number on the flow characteristics have been investigated as well.
Abstract: Nowadays, the plant location selection has a critical
impact on the performance of numerous companies. In this paper, a
methodology is presented to solve this problem. The three decision
making methods, namely Delphi, AHP and improved VIKOR, are
hybridized in order to make the best use of information available
based on the decision makers or experts. In this respect, the aim of
using Delphi is to select the most influential criteria by a few decision
makers. The AHP is utilized to give weights of the selected criteria.
Finally, the improved VIKOR method is applied to rank alternatives.
At the end of paper, an application example demonstrates the
applicability of the proposed methodology.
Abstract: In this study, a 3D combustion chamber was simulated
using FLUENT 6.32. Aim to obtain detailed information on
combustion characteristics and _ nitrogen oxides in the furnace and
the effect of oxygen enrichment in a combustion process. Oxygenenriched
combustion is an effective way to reduce emissions. This
paper analyzes NO emission, including thermal NO and prompt NO.
Flow rate ratio of air to fuel is varied as 1.3, 3.2 and 5.1 and the
oxygen enriched flow rates are 28, 54 and 68 lit/min. The 3D
Reynolds Averaged Navier Stokes (RANS) equations with standard
k-ε turbulence model are solved together by Fluent 6.32 software.
First order upwind scheme is used to model governing equations and
the SIMPLE algorithm is used as pressure velocity coupling. Results
show that for AF=1.3, increase the oxygen flow rate of oxygen
reduction in NO emissions is Lance. Moreover, in a fixed oxygen
enrichment condition, increasing the air to fuel ratio will increase the
temperature peak, but not the NO emission rate. As a result, oxygen
enrichment can reduce the NO emission at this kind of furnace in low
air to fuel rates.
Abstract: Study fluid flow and heat transfer characteristics of
microchannel in a primary Cross-corrugated(CC) surface recuperators
with corrugations and without corrugations, using CFD method. The
pitch-over-height ratios P/H of Cross-corrugated (CC) surface is from
1.5 to 4.0, included angles β=75º. The study was performed using CFD
software FLUENT to create unit model and simulate fluid
temperature, velocity, heat transfer coefficient and other parameters.
The results from these simulations were compared to experimental
data. It is concluded that, when the Reynolds number is constant, if
increase P/H, j/f will decrease, also the decreasing trend will become
weak. Under the condition of P/H=2.2, if increase the inlet velocity j/f
will decrease; in addition, the heat transfer performance in surface
with corrugation will increase 10% compared to that without
corrugation. The study results can provide the basis to optimize the
design, select the type of heat transfer surface, the scale structure, and
heat-transfer surface arrangement for recuperators.
Abstract: Oleic acid (C18:1) play an important role in
proliferation of fat cells. In this study, the effect of oleate on cells
viability in 3T3-L1 cells (fat cells) was investigated. The 3T3-L1
cells were treated with various concentrations of oleate in the
presence of 23 mM glucose. Oleate was added to adipogenic media
(day 0) to investigate the influence of oleate on proliferation of
postconfluent preadipocytes after 24 h induction. 0.1 mM oleate
promoted cell division by increasing 33.9% number of cells from
basal control in postconfluent preadipocytes. However, there were no
significantly different in cells viability with control cells when oleate
concentrations were increased up to 0.5 mM. When added to
differentiated adipocytes (day 12) for 48 h, the number of cells
decreased as oleate concentrations increased. 92.7% of cells lost
demonstrated apoptosis and necrosis after 48 h with 0.5 mM oleate.
The fluorochrome staining was examined under fluorescence
microscopy using acridine orange and ethidium bromide double
staining. Furthermore, the presence of high lactate (60.6% increased
from basal control) released into plasma has shown the direct
cytotoxicity of 0.5 mM oleate on adipocytes.
Abstract: The production of activated carbon from low or zero cost of agricultural by-products or wastes has received great attention from academics and practitioners due to its economic and environmental benefits. In the production of bamboo furniture, a significant amount of bamboo waste is inevitably generated. Therefore, this research aimed to prepare activated carbons from bamboo furniture waste by chemical (KOH) activation and determine their properties and adsorption capacities for water treatment. The influence of carbonization time on the properties and adsorption capacities of activated carbons was also investigated. The finding showed that the bamboo-derived activated carbons had microporous characteristics. They exhibited high tendency for the reduction of impurities present in effluent water. Their adsorption capacities were comparable to the adsorption capacity of a commercial activated carbon regarding to the reduction in COD, TDS and turbidity of the effluent water.
Abstract: This paper presents a comparative study of statistical methods for the multi-response surface optimization of a cryogenic freezing process. Taguchi design and analysis and steepest ascent methods based on the desirability function were conducted to ascertain the influential factors of a cryogenic freezing process and their optimal levels. The more preferable levels of the set point, exhaust fan speed, retention time and flow direction are set at -90oC, 20 Hz, 18 minutes and Counter Current, respectively. The overall desirability level is 0.7044.
Abstract: The effects of upflow liquid velocity (ULV) on
performance of expanded granular sludge bed (EGSB) system were
investigated. The EGSB reactor, made from galvanized steel pipe
0.10 m diameter and 5 m height, had been used to treat piggery
wastewater, after passing through acidification tank. It consisted of
39.3 l working volume in reaction zone and 122 l working volume in
sedimentation zone, at the upper part. The reactor was seeded with
anaerobically digested sludge and operated at the ULVs of 4, 8, 12
and 16 m/h, consecutively, corresponding to organic loading rates of
9.6 – 13.0 kg COD/ (m3.d). The average COD concentrations in the
influent were 9,601 – 13,050 mg/l. The COD removal was not
significantly different, i.e. 93.0% - 94.0%, except at ULV 12 m/h where
SS in the influent was exceptionally high so that VSS washout had
occurred, leading to low COD removal. The FCOD and VFA
concentrations in the effluent of all experiments were not much
different, indicating the same range of treatment performance. The
biogas production decreased at higher ULV and ULV of 4 m/h is
suggested as design criterion for EGSB system.
Abstract: A study was undertaken to assess the potential of an
Algal Turf Scrubber to remove nitrogen from aquaculture effluent to
reduce environmental pollution. High total ammonia nitrogen
concentrations were introduced to an Algal Turf Scrubber developed
under varying hydraulic surface loading rates of African catfish
(Clarius gariepinus) effluent in a recirculating aquaculture system.
Nutrient removal rates were not affected at total suspended solids
concentration of up to 0.04g TSS/l (P > 0.05). Nitrogen removal
rates 0.93-0.99g TAN/m²/d were recorded at very high loading rates
3.76-3.81 g TAN/m²/d. Total ammonia removal showed ½ order
kinetics between 1.6 to 2.3mg/l Total Ammonia Nitrogen
concentrations. Nitrogen removal increased with its loading, which
increased with hydraulic surface loading rate. Total Ammonia
Nitrogen removal by Algal turf scrubber was higher than reported
values for fluidized bed filters and trickling filters. The algal turf
scrubber also effectively removed nitrate thereby reducing the need
for water exchange.
Abstract: The purpose of this study is to examine the self and
decision making levels of students receiving education in schools of
physical training and sports. The population of the study consisted
258 students, among which 152 were male and 106 were female
( X age=19,3713 + 1,6968), that received education in the schools of
physical education and sports of Selcuk University, Inonu University,
Gazi University and Karamanoglu Mehmetbey University. In order to
achieve the purpose of the study, the Melbourne Decision Making
Questionnary developed by Mann et al. (1998) [1] and adapted to
Turkish by Deniz (2004) [2] and the Self-Esteem Scale developed by
Aricak (1999) [3] was utilized. For analyzing and interpreting data
Kolmogorov-Smirnov test, t-test and one way anova test were used,
while for determining the difference between the groups Tukey test
and Multiple Linear Regression test were employed and significance
was accepted at P
Abstract: Biological Ammonia removal (nitrification), the
oxidation of ammonia to nitrate catalyzed by bacteria, is a key part of
global nitrogen cycling. In the first step of nitrification,
chemolithoautotrophic ammonia oxidizer transform ammonia to
nitrite, this subsequently oxidized to nitrate by nitrite oxidizing
bacteria. This process can be affected by several factors. In this study
the effect of influent COD on biological ammonia removal in a
bench-scale biological reactor was investigated. Experiments were
carried out using synthetic wastewater. The initial ammonium
concentration was 25mgNH4
+-N L-1. The effect of COD between
247.55±1.8 and 601.08±3.24mgL-1 on biological ammonia removal
was investigated by varying the COD loading supplied to reactor.
From the results obtained in this study it could be concluded in the
range of 247.55±1.8 to 351.35±2.05mgL-1, there is a direct
relationship between amount of COD and ammonia removal.
However more than 351.35±2.05 up to 601.08±3.24mgL-1 were
found an indirect relationship between them.
Abstract: Pharmaceutical industries and effluents of sewage treatment plants are the main sources of residual pharmaceuticals in water resources. These emergent pollutants may adversely impact the biophysical environment. Pharmaceutical industries often generate wastewater that changes in characteristics and quantity depending on the used manufacturing processes. Carbamazepine (CBZ), {5Hdibenzo [b,f]azepine-5-carboxamide, (C15H12N2O)}, is a significant non-biodegradable pharmaceutical contaminant in the Jordanian pharmaceutical wastewater, which is not removed by the activated sludge processes in treatment plants. Activated carbon may potentially remove that pollutant from effluents, but the high cost involved suggests that more attention should be given to the potential use of low-cost materials in order to reduce cost and environmental contamination. Powders of Jordanian non-metallic raw materials namely, Azraq Bentonite (AB), Kaolinite (K), and Zeolite (Zeo) were activated (acid and thermal treatment) and evaluated by removing CBZ. The results of batch and column techniques experiments showed around 46% and 67% removal of CBZ respectively.
Abstract: There is a acute water problem especially in the dry
season in and around Perundurai (Erode district, Tamil Nadu, India)
where there are more number of tannery units. Hence an attempt was
made to use the waste water from tannery industry for construction
purpose. The mechanical properties such as compressive strength,
tensile strength, flexural strength etc were studied by casting various
concrete specimens in form of cube, cylinders and beams etc and
were found to be satisfactory. Hence some special properties such as
chloride attack, sulphate attack and chemical attack are considered
and comparatively studied with the conventional potable water. In
this experimental study the results of specimens prepared by using
treated and untreated tannery effluent were compared with the
concrete specimens prepared by using potable water. It was observed
that the concrete had some reduction in strength while subjected to
chloride attack, sulphate attack and chemical attack. So admixtures
were selected and optimized in suitable proportion to counter act the
adverse effects and the results were found to be satisfactory.