Abstract: From environmental aspect purification of ammonia
containing wastewater is expected. High efficiency ammonia
desorption can be done from the water by air on proper temperature.
After the desorption process, ammonia can be recovered and used in
another technology. The calculation method described below give
some methods to find either the minimum column height or ammonia
rich solution of the effluent.
Abstract: The quality of a machined surface is becoming more and more important to justify the increasing demands of sophisticated component performance, longevity, and reliability. Usually, any machining operation leaves its own characteristic evidence on the machined surface in the form of finely spaced micro irregularities (surface roughness) left by the associated indeterministic characteristics of the different elements of the system: tool-machineworkpart- cutting parameters. However, one of the most influential sources in machining affecting surface roughness is the instantaneous state of tool edge. The main objective of the current work is to relate the in-process immeasurable cutting edge deformation and surface roughness to a more reliable easy-to-measure force signals using a robust non-linear time-dependent modeling regression techniques. Time-dependent modeling is beneficial when modern machining systems, such as adaptive control techniques are considered, where the state of the machined surface and the health of the cutting edge are monitored, assessed and controlled online using realtime information provided by the variability encountered in the measured force signals. Correlation between wear propagation and roughness variation is developed throughout the different edge lifetimes. The surface roughness is further evaluated in the light of the variation in both the static and the dynamic force signals. Consistent correlation is found between surface roughness variation and tool wear progress within its initial and constant regions. At the first few seconds of cutting, expected and well known trend of the effect of the cutting parameters is observed. Surface roughness is positively influenced by the level of the feed rate and negatively by the cutting speed. As cutting continues, roughness is affected, to different extents, by the rather localized wear modes either on the tool nose or on its flank areas. Moreover, it seems that roughness varies as wear attitude transfers from one mode to another and, in general, it is shown that it is improved as wear increases but with possible corresponding workpart dimensional inaccuracy. The dynamic force signals are found reasonably sensitive to simulate either the progressive or the random modes of tool edge deformation. While the frictional force components, feeding and radial, are found informative regarding progressive wear modes, the vertical (power) components is found more representative carrier to system instability resulting from the edge-s random deformation.
Abstract: In designing river intakes and diversion structures, it is paramount that the sediments entering the intake are minimized or, if possible, completely separated. Due to high water velocity, sediments can significantly damage hydraulic structures especially when mechanical equipment like pumps and turbines are used. This subsequently results in wasting water, electricity and further costs. Therefore, it is prudent to investigate and analyze the performance of lateral intakes affected by sediment control structures. Laboratory experiments, despite their vast potential and benefits, can face certain limitations and challenges. Some of these include: limitations in equipment and facilities, space constraints, equipment errors including lack of adequate precision or mal-operation, and finally, human error. Research has shown that in order to achieve the ultimate goal of intake structure design – which is to design longlasting and proficient structures – the best combination of sediment control structures (such as sill and submerged vanes) along with parameters that increase their performance (such as diversion angle and location) should be determined. Cost, difficulty of execution and environmental impacts should also be included in evaluating the optimal design. This solution can then be applied to similar problems in the future. Subsequently, the model used to arrive at the optimal design requires high level of accuracy and precision in order to avoid improper design and execution of projects. Process of creating and executing the design should be as comprehensive and applicable as possible. Therefore, it is important that influential parameters and vital criteria is fully understood and applied at all stages of choosing the optimal design. In this article, influential parameters on optimal performance of the intake, advantages and disadvantages, and efficiency of a given design are studied. Then, a multi-criterion decision matrix is utilized to choose the optimal model that can be used to determine the proper parameters in constructing the intake.
Abstract: In the present paper; an experimental and numerical
investigations of drag reduction on a grooved circular cylinder have
been performed. The experiments were carried out in closed circuit
subsonic wind tunnel (TE44); the pressure distribution on the
cylinder was conducted using a TE44DPS differential pressure
scanner and the drag forces were measured using the TE81 balance.
The display unit is linked to a computer, loaded with DATASLIM
software for data analysis and logging of result. The numerical study
was performed using the code ANSYS FLUENT solving the
Reynolds Averaged Navier-Stokes (RANS) equations. The k-ε and k-
ω SST models were tested. The results obtained from the
experimental and numerical investigations have showed a reduction
in the drag when using longitudinal grooves namely 2 and 6 on the
cylinder.
Abstract: Pentachlorophenol (PCP) is a polychlorinated
aromatic compound that is widespread in industrial effluents and is
considered to be a serious pollutant. Among the variety of industrial
effluents encountered, effluents from tanning industry are very
important and have a serious pollution potential. PCP is also formed
unintentionally in effluents of paper and pulp industries. It is highly
persistent in soils and is lethal to a wide variety of beneficial
microorganisms and insects, human beings and animals. The natural
processes that breakdown toxic chemicals in the environment have
become the focus of much attention to develop safe and environmentfriendly
deactivation technologies. Microbes and plants are among
the most important biological agents that remove and degrade waste
materials to enable their recycling in the environment. The present
investigation was carried out with the aim of developing a microbial
system for bioremediation of PCP polluted soils. A number of plant
species were evaluated for their ability to tolerate different
concentrations of pentachlorophenol (PCP) in the soil. The
experiment was conducted for 30 days under pot culture conditions.
The toxic effect of PCP on plants was studied by monitoring seed
germination, plant growth and biomass. As the concentration of PCP
was increased to 50 ppm, the inhibition of seed germination, plant
growth and biomass was also increased. Although PCP had a
negative effect on all plant species tested, maize and groundnut
showed the maximum tolerance to PCP. Other tolerating crops
included wheat, safflower, sunflower, and soybean. From the
rhizosphere soil of the tolerant seedlings, as many as twenty seven
PCP tolerant bacteria were isolated. From soybean, 8; sunflower, 3;
safflower 8; maize 2; groundnut and wheat, 3 each isolates were
made. They were screened for their PCP degradation potentials.
HPLC analyses of PCP degradation revealed that the isolate MAZ-2
degraded PCP completely. The isolate MAZ-1 was the next best
isolate with 90 per cent PCP degradation. These strains hold promise
to be used in the bioremediation of PCP polluted soils.
Abstract: Chicken feathers were used as biosorbent for Pb
removal from aqueous solution. In this paper, the kinetics and
equilibrium studies at several pH, temperature, and metal
concentration values are reported. For tested conditions, the Pb
sorption capacity of this poultry waste ranged from 0.8 to 8.3 mg/g.
Optimal conditions for Pb removal by chicken feathers have been
identified. Pseudo-first order and pseudo-second order equations
were used to analyze the experimental data. In addition, the sorption
isotherms were fitted to classical Langmuir and Freundlich models.
Finally, thermodynamic parameters for the sorption process have
been determined. In summary, the results showed that chicken
feathers are an alternative and promising sorbent for the treatment of
effluents polluted by Pb ions.
Abstract: This study examined the underlying dimensions of
brand equity in the chocolate industry. For this purpose, researchers
developed a model to identify which factors are influential in
building brand equity. The second purpose was to assess brand
loyalty and brand images mediating effect between brand attitude,
brand personality, brand association with brand equity. The study
employed structural equation modeling to investigate the causal
relationships between the dimensions of brand equity and brand
equity itself. It specifically measured the way in which consumers’
perceptions of the dimensions of brand equity affected the overall
brand equity evaluations. Data were collected from a sample of
consumers of chocolate industry in Iran. The results of this empirical
study indicate that brand loyalty and brand image are important
components of brand equity in this industry. Moreover, the role of
brand loyalty and brand image as mediating factors in the intention of
brand equity are supported. The principal contribution of the present
research is that it provides empirical evidence of the
multidimensionality of consumer based brand equity, supporting
Aaker´s and Keller´s conceptualization of brand equity. The present
research also enriched brand equity building by incorporating the
brand personality and brand image, as recommended by previous
researchers. Moreover, creating the brand equity index in chocolate
industry of Iran particularly is novel.
Abstract: The bypass exhaust system of a 160 MW combined cycle has been modeled and analyzed using numerical simulation in 2D prospective. Analysis was carried out using the commercial numerical simulation software, FLUENT 6.2. All inputs were based on the technical data gathered from working conditions of a Siemens V94.2 gas turbine, installed in the Yazd power plant. This paper deals with reduction of pressure drop in bypass exhaust system using turning vanes mounted in diverter box in order to alleviate turbulent energy dissipation rate above diverter box. The geometry of such turning vanes has been optimized based on the flow pattern at diverter box inlet. The results show that the use of optimized turning vanes in diverter box can improve the flow pattern and eliminate vortices around sharp edges just before the silencer. Furthermore, this optimization could decrease the pressure drop in bypass exhaust system and leads to higher plant efficiency.
Abstract: In this study, a 3D combustion chamber was simulated
using FLUENT 6.32. Aims to obtain accurate information about the
profile of the combustion in the furnace and also check the effect of
oxygen enrichment on the combustion process. Oxygen enrichment is
an effective way to reduce combustion pollutant. The flow rate of air
to fuel ratio is varied as 1.3, 3.2 and 5.1 and the oxygen enriched
flow rates are 28, 54 and 68 lit/min. Combustion simulations
typically involve the solution of the turbulent flows with heat
transfer, species transport and chemical reactions. It is common to
use the Reynolds-averaged form of the governing equation in
conjunction with a suitable turbulence model. The 3D Reynolds
Averaged Navier Stokes (RANS) equations with standard k-ε
turbulence model are solved together by Fluent 6.3 software. First
order upwind scheme is used to model governing equations and the
SIMPLE algorithm is used as pressure velocity coupling. Species
mass fractions at the wall are assumed to have zero normal
gradients.Results show that minimum mole fraction of CO2 happens
when the flow rate ratio of air to fuel is 5.1. Additionally, in a fixed
oxygen enrichment condition, increasing the air to fuel ratio will
increase the temperature peak. As a result, oxygen-enrichment can
reduce the CO2 emission at this kind of furnace in high air to fuel
rates.
Abstract: Prior research has not effectively investigated how the
profitability of Chinese branches affect FDIs in China [1, 2], so this
study for the first time incorporates realistic earnings information
to systematically investigate effects of innovation, imitation, and
profit factors of FDI diffusions from Taiwan to China. Our nonlinear
least square (NLS) model, which incorporates earnings factors,
forms a nonlinear ordinary differential equation (ODE) in numerical
simulation programs. The model parameters are obtained through
a genetic algorithms (GA) technique and then optimized with the
collected data for the best accuracy. Particularly, Taiwanese regulatory
FDI restrictions are also considered in our modified model to meet
the realistic conditions. To validate the model-s effectiveness, this
investigation compares the prediction accuracy of modified model
with the conventional diffusion model, which does not take account
of the profitability factors.
The results clearly demonstrate the internal influence to be positive,
as early FDI adopters- consistent praises of FDI attract potential firms
to make the same move. The former erects a behavior model for the
latter to imitate their foreign investment decision. Particularly, the
results of modified diffusion models show that the earnings from
Chinese branches are positively related to the internal influence. In
general, the imitating tendency of potential consumers is substantially
hindered by the losses in the Chinese branches, and these firms would
invest less into China. The FDI inflow extension depends on earnings
of Chinese branches, and companies will adjust their FDI strategies
based on the returns. Since this research has proved that earning is
an influential factor on FDI dynamics, our revised model explicitly
performs superior in prediction ability than conventional diffusion
model.
Abstract: Anaerobic Digestion has become a promising
technology for biological transformation of organic fraction of the
municipal solid wastes (MSW). In order to represent the kinetic
behavior of such biological process and thereby to design a reactor
system, development of a mathematical model is essential.
Addressing this issue, a simplistic mathematical model has been
developed for anaerobic digestion of MSW in a continuous flow
reactor unit under homogeneous steady state condition. Upon
simulated hydrolysis, the kinetics of biomass growth and substrate
utilization rate are assumed to follow first order reaction kinetics.
Simulation of this model has been conducted by studying sensitivity
of various process variables. The model was simulated using typical
kinetic data of anaerobic digestion MSW and typical MSW
characteristics of Kolkata. The hydraulic retention time (HRT) and
solid retention time (SRT) time were mainly estimated by varying
different model parameters like efficiency of reactor, influent
substrate concentration and biomass concentration. Consequently,
design table and charts have also been prepared for ready use in the
actual plant operation.
Abstract: This research aims at modeling and simulating the effects of nanofluids on cylindrical heat pipes thermal performance using the ANSYS-FLUENT CFD commercial software. The heat pipe outer wall temperature distribution, thermal resistance, liquid pressure and axial velocity in presence of suspended nano-scaled solid particle (i.e. Cu, Al2O3 and TiO2) within the fluid (water) were investigated. The effect of particle concentration and size were explored and it is concluded that the thermal performance of the heat pipe is improved when using nanofluid as the system working fluid. Additionally, it was observed that the thermal resistance of the heat pipe drops as the particle concentration level increases and particle radius decreases.
Abstract: A new conceptual architecture for low-level neural
pattern recognition is presented. The key ideas are that the brain
implements support vector machines and that support vectors are
represented as memory patterns in competitive queuing memories. A
binary classifier is built from two competitive queuing memories
holding positive and negative valence training examples respectively.
The support vector machine classification function is calculated in
synchronized evaluation cycles. The kernel is computed by bisymmetric
feed-forward networks feed by sensory input and by
competitive queuing memories traversing the complete sequence of
support vectors. Temporary summation generates the output
classification. It is speculated that perception apparatus in the brain
reuses structures that have evolved for enabling fluent execution of
prepared action sequences so that pattern recognition is built on
internalized motor programmes.
Abstract: This study deals with Computational Fluid Dynamics
(CFD) studies of the interactions between the air flow and louvered
fins which equipped the automotive heat exchangers. 3D numerical
simulation results are obtained by using the ANSYS Fluent 13.0 code
and compared to experimental data. The paper studies the effect of
louver angle and louver pitch geometrical parameters, on overall
thermal hydraulic performances of louvered fins.
The comparison between CFD simulations and experimental data
show that established 3-D CFD model gives a good agreement. The
validation agrees, with about 7% of deviation respectively of friction
and Colburn factors to experimental results. As first, it is found that
the louver angle has a strong influence on the heat transfer rate. Then,
louver angle and louver pitch variation of the louvers and their effects
on thermal hydraulic performances are studied. In addition to this
study, it is shown that the second half of the fin takes has a
significant contribution on pressure drop increase without any
increase in heat transfer.
Abstract: This paper investigates experimental and numerical study of the airflow characteristics for vortex, round and square ceiling diffusers and its effect on the thermal comfort in a ventilated room. Three different thermal comfort criteria namely; Mean Age of the Air (MAA), ventilation effectiveness (E), and Effective Draft Temperature (EDT) have been used to predict the thermal comfort zone inside the room. In experimental work, a sub-scale room is set-up to measure the temperature field in the room. In numerical analysis, unstructured grids have been used to discretize the numerical domain. Conservation equations are solved using FLUENT commercial flow solver. The code is validated by comparing the numerical results obtained from three different turbulence models with the available experimental data. The comparison between the various numerical models shows that the standard k-ε turbulence model can be used to simulate these cases successfully. After validation of the code, effect of supply air velocity on the flow and thermal field could be investigated and hence the thermal comfort. The results show that the pressure coefficient created by the square diffuser is 1.5 times greater than that created by the vortex diffuser. The velocity decay coefficient is nearly the same for square and round diffusers and is 2.6 times greater than that for the vortex diffuser.
Abstract: The paper discusses a 3D numerical solution of the inverse boundary problem for a continuous casting process of alloy. The main goal of the analysis presented within the paper was to estimate heat fluxes along the external surface of the ingot. The verified information on these fluxes was crucial for a good design of a mould, effective cooling system and generally the whole caster. In the study an enthalpy-porosity technique implemented in Fluent package was used for modeling the solidification process. In this method, the phase change interface was determined on the basis of the liquid fraction approach. In inverse procedure the sensitivity analysis was applied for retrieving boundary conditions. A comparison of the measured and retrieved values showed a high accuracy of the computations. Additionally, the influence of the accuracy of measurements on the estimated heat fluxes was also investigated.
Abstract: Heavy rainfall greatly affects the aerodynamic performance of the aircraft. There are many accidents of aircraft caused by aerodynamic efficiency degradation by heavy rain.
In this Paper we have studied the heavy rain effects on the aerodynamic efficiency of cambered NACA 64-210 and symmetric
NACA 0012 airfoils. Our results show significant increase in drag and decrease in lift. We used preprocessing software gridgen for creation of geometry and mesh, used fluent as solver and techplot as postprocessor. Discrete phase modeling called DPM is used to model the rain particles using two phase flow approach. The rain particles are assumed to be inert.
Both airfoils showed significant decrease in lift and increase in drag in simulated rain environment. The most significant difference between these two airfoils was the NACA 64-210 more sensitivity than NACA 0012 to liquid water content (LWC). We believe that the results showed in this paper will be useful for the designer of the commercial aircrafts and UAVs, and will be helpful for training of the pilots to control the airplanes in heavy rain.
Abstract: The objective of this study is to investigate fire
behaviors, experimentally and numerically, in a scaled version of an
underground station. The effect of ventilation velocity on the fire is
examined. Fire experiments are simulated by burning 10 ml
isopropyl alcohol fuel in a fire pool with dimensions 5cm x 10cm x 4
mm at the center of 1/100 scaled underground station model. A
commercial CFD program FLUENT was used in numerical
simulations. For air flow simulations, k-ω SST turbulence model and
for combustion simulation, non-premixed combustion model are
used. This study showed that, the ventilation velocity is increased
from 1 m/s to 3 m/s the maximum temperature in the station is found
to be less for ventilation velocity of 1 m/s. The reason for these
experimental result lies on the relative dominance of oxygen supply
effect on cooling effect. Without piston effect, maximum temperature
occurs above the fuel pool. However, when the ventilation velocity
increased the flame was tilted in the direction of ventilation and the
location of maximum temperature moves along the flow direction.
The velocities measured experimentally in the station at different
locations are well matched by the CFD simulation results. The
prediction of general flow pattern is satisfactory with the smoke
visualization tests. The backlayering in velocity is well predicted by
CFD simulation. However, all over the station, the CFD simulations
predicted higher temperatures compared to experimental
measurements.
Abstract: The Beshar River is one aquatic ecosystem,which is
affected by pollutants. This study was conducted to evaluate the
effects of human activities on the water quality of the Beshar river.
This river is approximately 190 km in length and situated at the
geographical positions of 51° 20' to 51° 48' E and 30° 18' to 30° 52'
N it is one of the most important aquatic ecosystems of Kohkiloye
and Boyerahmad province next to the city of Yasuj in southern Iran.
The Beshar river has been contaminated by industrial, agricultural
and other activities in this region such as factories, hospitals,
agricultural farms, urban surface runoff and effluent of wastewater
treatment plants. In order to evaluate the effects of these pollutants
on the quality of the Beshar river, five monitoring stations were
selected along its course. The first station is located upstream of
Yasuj near the Dehnow village; stations 2 to 4 are located east, south
and west of city; and the 5th station is located downstream of Yasuj.
Several water quality parameters were sampled. These include pH,
dissolved oxygen, biological oxygen demand (BOD), temperature,
conductivity, turbidity, total dissolved solids and discharge or flow
measurements. Water samples from the five stations were collected
and analysed to determine the following physicochemical
parameters: EC, pH, T.D.S, T.H, No2, DO, BOD5, COD during 2008
to 2009. The study shows that the BOD5 value of station 1 is at a
minimum (1.5 ppm) and increases downstream from stations 2 to 4 to
a maximum (7.2 ppm), and then decreases at station 5. The DO
values of station 1 is a maximum (9.55 ppm), decreases downstream
to stations 2 - 4 which are at a minimum (3.4 ppm), before increasing
at station 5. The amount of BOD and TDS are highest at the 4th
station and the amount of DO is lowest at this station, marking the
4th station as more highly polluted than the other stations. The
physicochemical parameters improve at the 5th station due to
pollutant degradation and dilution. Finally the point and nonpoint
pollutant sources of Beshar river were determined and compared to
the monitoring results.
Abstract: This study developed a high efficient and combined
biological and chemical filter treatment process. This process used
PAC (Powder Activated Carbon), Alum and attached growth
treatment process. The system removals of total nitrogen and total
phosphorus ratio of two were as high as 70% and 73%, moreover, the
effluent water was suitable to urban and agricultural water. Also the
advantages of this process are not only occupies small place but is
simple, economic and easy operating. Besides, our developed process
can keep stable process efficiency even in relative low load level.
Therefore, this study judges that use of the high efficient and
combined biological and chemical filter treatment process, it is
expected that the effluent water in this system can be reused as urban
and agricultural water.