Abstract: The quantified residence time distribution (RTD)
provides a numerical characterization of mixing in a reactor, thus
allowing the process engineer to better understand mixing
performance of the reactor.This paper discusses computational
studies to investigate flow patterns in a two impinging streams
cyclone reactor(TISCR) . Flow in the reactor was modeled with
computational fluid dynamics (CFD). Utilizing the Eulerian-
Lagrangian approach, implemented in FLUENT (V6.3.22), particle
trajectories were obtained by solving the particle force balance
equations. From simulation results obtained at different Δts, the mean
residence time (tm) and the mean square deviation (σ2) were
calculated. a good agreement can be observed between predicted and
experimental data. Simulation results indicate that the behavior of
complex reactor systems can be predicted using the CFD technique
with minimum data requirement for validation.
Abstract: This paper presents a numerical study on surface heat
transfer characteristics of laminar air flows in parallel-plate dimpled
channels. The two-dimensional numerical model is provided by
commercial code FLUENT and the results are obtained for channels
with symmetrically opposing hemi-cylindrical cavities onto both
walls for Reynolds number ranging from 1000 to 2500. The influence
of variations in relative depth of dimples (the ratio of cavity depth to
the cavity curvature diameter), the number of them and the thermophysical
properties of channel walls on heat transfer enhancement is
studied. The results are evident for existence of an optimum value for
the relative depth of dimples in which the largest wall heat flux and
average Nusselt number can be achieved. In addition, the results of
conjugation simulation indicate that the overall influence of the ratio
of wall thermal conductivity to the one of the fluid on heat transfer
rate is not much significant and can be ignored.
Abstract: Anaerobic treatment has many advantages over other
biological method particularly when used to treat complex
wastewater such as petroleum refinery wastewater. In this study two
Up-flow Anaerobic Sludge Blanket (UASB) reactors were operated
in parallel to treat six volumetric organic loads (0.58, 1.21, 0.89,
2.34, 1.47 and 4.14 kg COD/m3·d) to evaluate the chemical oxygen
demand (COD) removal efficiency. The reactors were continuously
adapting to the changing of operation condition with increase in the
removal efficiency or slight decrease until the last load which was
more than two times the load, at which the reactor stressed and the
removal efficiency decreased to 75% with effluent concentration of
1746 mg COD/L. Other parameters were also monitored such as pH,
alkalinity, volatile fatty acid and gas production rate. The UASB
reactor was suitable to treat petroleum refinery wastewater and the
highest COD removal rate was 83% at 1215 kg/m3·d with COD
concentration about 356 mg/L in the effluent.
Abstract: Studies on residential satisfaction have been actively
discussed under family house setting. However, limited studies have
been conducted on student residential satisfaction. This study is an
attempt to fill the research gap. It focuses on the influence of socioeconomic
on students- satisfaction with the universities- student
housing facilities. The students who stayed at the on-campus student
housing were the respondents. This study employed two-stage cluster
sampling method in classifying the respondents. Self-administered
questionnaires were distributed face-to-face to the students. In
general, it is confirmed that students- socio-economic backgrounds
have influence on the students- satisfaction with their housing
facilities. The main influential factors were the students- economic
status, sense of sharing, and ethnicity of their roommates.
Furthermore, this study could also provide a useful feedback for the
universities in order to improve their student housing facilities.
Abstract: As the Textile Industry is the second largest industry
in Egypt and as small and medium-sized enterprises (SMEs) make up
a great portion of this industry therein it is essential to apply the
concept of Cleaner Production for the purpose of reducing pollution.
In order to achieve this goal, a case study concerned with ecofriendly
stone-washing of jeans-garments was investigated. A raw
material-substitution option was adopted whereby the toxic
potassium permanganate and sodium sulfide were replaced by the
environmentally compatible hydrogen peroxide and glucose
respectively where the concentrations of both replaced chemicals
together with the operating time were optimized. In addition, a
process-rationalization option involving four additional processes
was investigated. By means of criteria such as product quality,
effluent analysis, mass and heat balance; and cost analysis with the
aid of a statistical model, a process optimization treatment revealed
that the superior process optima were 50%, 0.15% and 50min for
H2O2 concentration, glucose concentration and time, respectively.
With these values the superior process ought to reduce the annual
cost by about EGP 105 relative to the currently used conventional
method.
Abstract: The purpose of this study is to find natural gait of
biped robot such as human being by analyzing the COG (Center Of
Gravity) trajectory of human being's gait. It is discovered that human
beings gait naturally maintain the stability and use the minimum
energy. This paper intends to find the natural gait pattern of biped
robot using the minimum energy as well as maintaining the stability by
analyzing the human's gait pattern that is measured from gait image on
the sagittal plane and COG trajectory on the frontal plane. It is not
possible to apply the torques of human's articulation to those of biped
robot's because they have different degrees of freedom. Nonetheless,
human and 5-link biped robots are similar in kinematics. For this, we
generate gait pattern of the 5-link biped robot by using the GA
algorithm of adaptation gait pattern which utilize the human's ZMP
(Zero Moment Point) and torque of all articulation that are measured
from human's gait pattern. The algorithm proposed creates biped
robot's fluent gait pattern as that of human being's and to minimize
energy consumption because the gait pattern of the 5-link biped robot
model is modeled after consideration about the torque of human's each
articulation on the sagittal plane and ZMP trajectory on the frontal
plane. This paper demonstrate that the algorithm proposed is superior
by evaluating 2 kinds of the 5-link biped robot applied to each gait
patterns generated both in the general way using inverse kinematics
and in the special way in which by considering visuality and
efficiency.
Abstract: The Beshar River is one aquatic ecosystem, which is
located next to the city of Yasuj in southern Iran. The Beshar river
has been contaminated by industrial factories such as effluent of
sugar factory, agricultural and other activities in this region such as,
Imam Sajjad hospital, drainage from agricultural farms, Yasuj urban
surface runoff and effluent of wastewater treatment plants ,specially
Yasuj waste water treatment plant. In order to evaluate the effects of
these pollutants on the quality of the Beshar river, five monitoring
stations were selected along its course. The first station is located
upstream of Yasuj near the Dehnow village; stations 2 to 4 are
located east, south and west of city; and the 5th station is located
downstream of Yasuj. Several water quality parameters were
sampled. These include pH, dissolved oxygen, biological oxygen
demand (BOD), temperature, conductivity, turbidity, total dissolved
solids and discharge or flow measurements. Water samples from the
five stations were collected and analyzed to determine the following
physicochemical parameters: EC, pH, T.D.S, T.H, No2, DO, BOD5,
COD during 2008 to 2010. The study shows that the BOD5 value of
station 1 is at a minimum (1.7 ppm) and increases downstream from
stations 2 to 4 to a maximum (11.6 ppm), and then decreases at
station 5. The DO values of station 1 is a maximum (8.45 ppm),
decreases downstream to stations 2 - 4 which are at a minimum (3.1
ppm), before increasing at station 5. The amount of BOD and TDS
are highest at the 4th station and the amount of DO is lowest at this
station, marking the 4th station as more highly polluted than the
other stations .This study shows average amount of the water quality
parameters in first year of sampling (2008) have had a better quality
relation to third year in 2010 because of recent drought in this region
and pollutant increasing .As the Beshar river path after 5th station
goes through the mountain area with more slope and flow velocity
,so the physicochemical parameters improve at the 5th station due to
pollutant degradation and dilution. Finally the point and nonpoint
pollutant sources of Beshar river were determined and compared to
the monitoring results.
Abstract: There have been widespread applications of fluidized beds in industries which are related to the combination of gas-solid particles during the last decade. For instance, in order to crack the catalyses in petrochemical industries or as a drier in food industries. High capacity of fluidized bed in heat and mass transfer has made this device very popular. In order to achieve a higher efficiency of fluidized beds, a particular attention has been paid to beds with pulsating air flow. In this paper, a fluidized bed device with pulsating flow has been designed and constructed. Size of particles have been used during the test are in the range of 40 to 100μm. The purpose of this experimental test is to investigate the air flow regime, observe the particles- movement and measure the pressure loss along the bed. The effects of pulsation can be evaluated by comparing the results for both continuous and pulsating flow. Results of both situations are compared for various gas speeds. Moreover the above experiment is numerically simulated by using Fluent software and its numerical results are compared with the experimental results.
Abstract: The present paper was concerned primarily with the
analysis, simulation of the air flow and thermal patterns in a lecture
room. The paper is devoted to numerically investigate the influence
of location and number of ventilation and air conditioning supply and
extracts openings on air flow properties in a lecture room. The work
focuses on air flow patterns, thermal behaviour in lecture room where
large number of students. The effectiveness of an air flow system is
commonly assessed by the successful removal of sensible and latent
loads from occupants with additional of attaining air pollutant at a
prescribed level to attain the human thermal comfort conditions and
to improve the indoor air quality; this is the main target during the
present paper. The study is carried out using computational fluid
dynamics (CFD) simulation techniques as embedded in the
commercially available CFD code (FLUENT 6.2). The CFD
modelling techniques solved the continuity, momentum and energy
conservation equations in addition to standard k – ε model equations
for turbulence closure.
Throughout the investigations, numerical validation is carried out by
way of comparisons of numerical and experimental results. Good
agreement is found among both predictions.
Abstract: In today's world where everything is rapidly changing
and information technology is high in development, many features of culture, society, politic and economy has changed. The advent of
information technology and electronic data transmission lead to easy communication and fields like e-learning and e-commerce, are
accessible for everyone easily. One of these technologies is virtual
training. The "quality" of such kind of education systems is critical. 131 questionnaires were prepared and distributed among university
student in Toba University. So the research has followed factors that affect the quality of learning from the perspective of staff, students, professors and this type of university. It is concluded that the important factors in virtual training are the quality of professors, the
quality of staff, and the quality of the university. These mentioned factors were the most prior factors in this education system and
necessary for improving virtual training.
Abstract: In designing of condensers, the prediction of pressure
drop is as important as the prediction of heat transfer coefficient.
Modeling of two phase flow, particularly liquid – vapor flow under
diabatic conditions inside a horizontal tube using CFD analysis is
difficult with the available two phase models in FLUENT due to
continuously changing flow patterns. In the present analysis, CFD
analysis of two phase flow of refrigerants inside a horizontal tube of
inner diameter, 0.0085 m and 1.2 m length is carried out using
homogeneous model under adiabatic conditions. The refrigerants
considered are R22, R134a and R407C. The analysis is performed at
different saturation temperatures and at different flow rates to
evaluate the local frictional pressure drop. Using Homogeneous
model, average properties are obtained for each of the refrigerants
that is considered as single phase pseudo fluid. The so obtained
pressure drop data is compared with the separated flow models
available in literature.
Abstract: A numerical method is developed for simulating
the motion of particles with arbitrary shapes in an effectively
infinite or bounded viscous flow. The particle translational and
angular motions are numerically investigated using a fluid-structure
interaction (FSI) method based on the Arbitrary-Lagrangian-Eulerian
(ALE) approach and the dynamic mesh method (smoothing and
remeshing) in FLUENT ( ANSYS Inc., USA). Also, the effects of
arbitrary shapes on the dynamics are studied using the FSI method
which could be applied to the motions and deformations of a single
blood cell and multiple blood cells, and the primary thrombogenesis
caused by platelet aggregation. It is expected that, combined with a
sophisticated large-scale computational technique, the simulation
method will be useful for understanding the overall properties of blood
flow from blood cellular level (microscopic) to the resulting
rheological properties of blood as a mass (macroscopic).
Abstract: While many studies have conducted the achievement
gap between groups of students in school districts, few studies have
utilized resilience research to investigate achievement gaps within
classrooms. This paper aims to summarize and discuss some recent
studies Waxman, Padr├│n, and their colleagues conducted, in which
they examined learning environment differences between resilient
and nonresilient students in reading and mathematics classrooms.
The classes consist of predominantly Hispanic elementary school
students from low-income families. These studies all incorporated
learning environment questionnaires and systematic observation
methods. Significant differences were found between resilient and
nonresilient students on their classroom learning environments and
classroom behaviors. The observation results indicate that the amount
and quality of teacher and student academic interaction are two of the
most influential variables that promote student outcomes. This paper
concludes by suggesting the following teacher practices to promote
resiliency in schools: (a) using feedback from classroom observation
and learning environment measures, (b) employing explicit teaching
practices; and (c) understanding students on a social and personal
level.
Abstract: The characteristics of fluid flow and phase separation
in an oil-water separator were numerically analysed as part of the
work presented herein. Simulations were performed for different
velocities and droplet diameters, and the way this parameters can
influence the separator geometry was studied.
The simulations were carried out using the software package
Fluent 6.2, which is designed for numerical simulation of fluid flow
and mass transfer. The model consisted of a cylindrical horizontal
separator. A tetrahedral mesh was employed in the computational
domain. The condition of two-phase flow was simulated with the
two-fluid model, taking into consideration turbulence effects using
the k-ε model.
The results showed that there is a strong dependency of phase
separation on mixture velocity and droplet diameter. An increase in
mixture velocity will bring about a slow down in phase separation
and as a consequence will require a weir of greater height. An
increase in droplet diameter will produce a better phase separation.
The simulations are in agreement with results reported in literature
and show that CFD can be a useful tool in studying a horizontal oilwater
separator.
Abstract: Empty Fruit Bunches (EFB) and Palm Oil Mill
Effluent (POME) are two main wastes from oil palm industries which
contain rich lignocellulose. Degradation of EFB and POME by
microorganisms will produce hydrolytic enzyme which will degrade
cellulose and hemicellulose during composting process. However,
normal composting takes about four to six months to reach maturity.
Hence, application of fungi into compost can shorten the period of
composting. This study identifies the effect of xylanase and cellulase
produced by Aspergillus niger and Trichoderma virens on
composting process using EFB and POME. The degradation of EFB
and POME indicates the lignocellulolytic capacity of Aspergillus
niger and Trichoderma virens with more than 7% decrease in
hemicellulose and more than 25% decrease in cellulose for both
inoculated compost. Inoculation of Aspergillus niger and
Trichoderma virens also increased the enzyme activities during the
composting period compared to the control compost by 21% for both
xylanase and cellulase. Rapid rise in the activities of cellulase and
xylanase was observed by Aspergillus niger with the highest
activities of 14.41 FPU/mg and 3.89 IU/mg, respectively. Increased
activities of cellulase and xylanase also occurred in inoculation of
Trichoderma virens with the highest activities obtained at 13.21
FPU/mg and 4.43 IU/mg, respectively. Therefore, it is evident that
the inoculation of fungi can increase the enzyme activities hence
effectively degrading the EFB and POME.
Abstract: The present study is concerned with effect of exciting
boundary layer on increase in heat transfer from flat surfaces. As any
increase in heat transfer between a fluid inside a face and another one
outside of it can cause an increase in some equipment's efficiency, so
at this present we have tried to increase the wall's heat transfer
coefficient by exciting the fluid boundary layer. By a collision
between flow and the placed block at the fluid way, the flow pattern
and the boundary layer stability will change. The flow way inside the
channel is simulated as a 2&3-dimensional channel by Gambit
TM
software.
With studying the achieved results by this simulation for the flow
way inside the channel with a block coordinating with Fluent
TM
software, it's determined that the figure and dimensions of the exciter
are too important for exciting the boundary layer so that any increase
in block dimensions in vertical side against the flow and any
reduction in its dimensions at the flow side can increase the average
heat transfer coefficient from flat surface and increase the flow
pressure loss. Using 2&3-dimensional analysis on exciting the flow at
the flow way inside a channel by cylindrical block at the same time
with the external flow, we came to this conclusion that the heat flux
transferred from the surface, is increased considerably in terms of the
condition without excitation. Also, the k-e turbulence model is used.
Abstract: The growth of the aquaculture industry has been
associated with negative environmental impacts through the
discharge of raw effluents into the adjacent receiving water bodies.
Macrophytes from natural saline lakes, which have adaptability to the
high salinity, can be suitable for saline effluent treatment. Eight
emergent species from natural saline area were planted in an
experimental gravel bed hydroponic mesocosm (GBH) which was
treated with effluent water from an intensive fish farm using
geothermal water. In order to examine the applicability of the
halophytes in treatment processes, we tested the relative efficacy of
total nitrogen (TN), total phosphorus (TP), potassium (K), sodium
(Na), magnesium (Mg) and calcium (Ca) removal for the saline
wastewater treatment. Four of the eight species, which were
Phragmites australis, Typha angustifolia, Glyceria maxima, Scirpus
lacustris spp. tabernaemontani could survive and contribute the
experimental treatment.
Abstract: This work aims to investigate a potential of
microalgae for utilizing industrial wastewater as a cheap nutrient for
their growth and oil accumulation. Wastewater was collected from
the effluent ponds of agro-industrial factories (cassava and ethanol
production plants). Only 2 microalgal strains were isolated and
identified as Scenedesmus quadricauda and Chlorella sp.. However,
only S. quadricauda was selected to cultivate in various wastewater
concentrations (10%, 20%, 40%, 60%, 80% and 100%). The highest
biomass obtained at 6.6×106 and 6.27×106 cells/ml when 60%
wastewater was used in flask and photo-bioreactor. The cultures gave
the highest lipid content at 18.58 % and 42.86% in cases of S.
quadricauda and S. obliquus. In addition, under salt stress (1.0 M
NaCl), S. obliquus demonstrated the highest lipid content at 50%
which was much more than the case of no NaCl adding. However, the
concentration of NaCl does not affect on lipid accumulation in case
of S. quadricauda.
Abstract: Natural ventilation is an important means to improve indoor thermal comfort and reduce the energy consumption. A solar chimney system is an enhancing natural draft device, which uses solar radiation to heat the air inside the chimney, thereby converting the thermal energy into kinetic energy. The present study considered some parameters such as chimney width and solar intensity, which were believed to have a significant effect on space ventilation. Fluent CFD software was used to predict buoyant air flow and flow rates in the cavities. The results were compared with available published experimental and theoretical data from the literature. There was an acceptable trend match between the present results and the published data for the room air change per hour, ACH. Further, it was noticed that the solar intensity has a more significant effect on ACH.
Abstract: The purpose of this article is to analyze the
degree of concentration in the banking market in EU member
states as well as to determine the impact of the length of EU
membership on the degree of concentration. In that sense
several analysis were conducted, specifically, panel analysis,
calculation of correlation coefficient and regression analysis of
the impact of the length of EU membership on the degree of
concentration. Panel analysis was conducted to determine
whether there is a similar trend of concentration in three
groups of countries - countries with a low, moderate and high
level of concentration. The conducted panel analysis showed
that in EU countries with a moderate level of concentration,
the level of concentration decreases. The calculation of
correlation showed that, to some extent, with other influential
factors, the length of EU membership negatively affects the
market concentration of the banking market. Using the
regression analysis for investigation of the influence of the
length of EU membership on the level of concentration in the
banking sector in a particular country, the results reveal that
there is a negative effect of the length in EU membership on
market concentration, although it is not significantly influential
variable.