Abstract: This paper describes an ab-initio design, development and calibration results of an Optical Sensor Ground Reaction Force Measurement Platform (OSGRFP) for gait and geriatric studies. The developed system employs an array of FBG sensors to measure the respective ground reaction forces from all three axes (X, Y and Z), which are perpendicular to each other. The novelty of this work is two folded. One is in its uniqueness to resolve the tri axial resultant forces during the stance in to the respective pure axis loads and the other is the applicability of inherently advantageous FBG sensors which are most suitable for biomechanical instrumentation. To validate the response of the FBG sensors installed in OSGRFP and to measure the cross sensitivity of the force applied in other directions, load sensors with indicators are used. Further in this work, relevant mathematical formulations are presented for extracting respective ground reaction forces from wavelength shifts/strain of FBG sensors on the OSGRFP. The result of this device has implications in understanding the foot function, identifying issues in gait cycle and measuring discrepancies between left and right foot. The device also provides a method to quantify and compare relative postural stability of different subjects under test, which has implications in post-surgical rehabilitation, geriatrics and optimizing training protocols for sports personnel.
Abstract: With the strengthened regulation on the mandatory use
of recycled aggregate, development of construction materials using
recycled aggregate has recently increased. This study aimed to secure
the performance of asphalt concrete mixture by developing
recycled-modified asphalt using recycled basalt aggregate from the
Jeju area. The strength of the basalt aggregate from the Jeju area used
in this study was similar to that of general aggregate, while the specific
surface area was larger due to the development of pores. Modified
asphalt was developed using a general aggregate-recycled aggregate
ratio of 7:3, and the results indicated that the Marshall stability
increased by 27% compared to that of asphalt concrete mixture using
only general aggregate, and the flow values showed similar levels.
Also, the indirect tensile strength increased by 79%, and the toughness
increased by more than 100%. In addition, the TSR for examining
moisture resistance was 0.95 indicating that the reduction in the
indirect tensile strength due to moisture was very low (5% level), and
the developed recycled-modified asphalt could satisfy all the quality
standards of asphalt concrete mixture.
Abstract: Medicinal and aromatic plants are promising and are characterized by the biosynthesis of odorous molecules that make up the so-called essential oils (EO), which have long been known for their antiseptic and therapeutic activity in folk medicine. Essential oils have many therapeutic properties. In herbal medicine, they are used for their antiseptic properties against infectious diseases of fungal origin, against dermatophytes, those of bacterial origin. The objective of this study was to evaluate the influence of drying in the shade on the water content and on the content of essential oils extracted from leaves of Eucalyptus camendulensis for better quality control of medicinal and aromatic plants. The water content of the Eucalyptus camendulensis plant material decreases during the drying process. It decreased from 100% to 0.006% for the drying in the shade after ten days. The moisture content is practically constant at the end of the drying period. The drying in the shade increases the concentration of essential oils of Eucalyptus camendulensis. When the leaves of Eucalyptus camendulensis plant are in the shade, the maximum of the essential oil content was obtained on the eighth day, the recorded value was 1.43% ± 0.01%. Beyond these periods, the content continuously drop in before stabilizing. The optimum drying time is between 6 and 9 days.
Abstract: This paper aims to link together the concepts of job
satisfaction, work engagement, trust, job meaningfulness and loyalty
to the organisation focusing on specific type of employment –
academic jobs. The research investigates the relationships between
job satisfaction, work engagement and loyalty as well as the impact
of trust and job meaningfulness on the work engagement and loyalty.
The survey was conducted in one of the largest Latvian higher
education institutions and the sample was drawn from academic staff
(n=326). Structured questionnaire with 44 reflective type questions
was developed to measure the constructs. Data was analysed using
SPSS and Smart-PLS software. Variance based structural equation
modelling (PLS-SEM) technique was used to test the model and to
predict the most important factors relevant to employee engagement
and loyalty. The first order model included two endogenous
constructs (loyalty and intention to stay and recommend to work in
this organisation, and employee engagement), as well as six
exogenous constructs (feeling of fair treatment and trust in
management; career growth opportunities; compensation, pay and
benefits; management; colleagues and teamwork; and finally job
meaningfulness). Job satisfaction was developed as second order
construct and both: first and second order models were designed for
data analysis. It was found that academics are more engaged than
satisfied with their work and main reason for that was found to be job
meaningfulness, which is significant predictor for work engagement,
but not for job satisfaction. Compensation is not significantly related
to work engagement, but only to job satisfaction. Trust was not
significantly related neither to engagement, nor to satisfaction,
however, it appeared to be significant predictor of loyalty and
intentions to stay with the University. Paper revealed academic jobs
as specific kind of employment where employees can be more
engaged than satisfied and highlighted the specific role of job
meaningfulness in the University settings.
Abstract: Motion response of floating structures is of great
concern in marine engineering. Nonlinearity is an inherent property
of any floating bodies subjected to irregular waves. These floating
structures are continuously subjected to environmental loadings from
wave, current, wind etc. This can result in undesirable motions of the
vessel which may challenge the operability. For a floating body to
remain in its position, it should be able to induce a restoring force
when displaced. Mooring is provided to enable this restoring force.
This paper discusses the hydrodynamic performance and motion
characteristics of an 8 point spread mooring system applied to a pipe
laying barge operating in the West African sea. The modelling of the
barge is done using a computer aided-design (CAD) software
RHINOCEROS. Irregular waves are generated using a suitable wave
spectrum. Both frequency domain and time domain analysis is done.
Numerical simulations based on potential theory are carried out to
find the responses and hydrodynamic performance of the barge in
both free floating as well as moored conditions. Initially, potential
flow frequency domain analysis is done to obtain the Response
Amplitude Operator (RAO) which gives an idea about the structural
motion in free floating state. RAOs for different wave headings are
analyzed. In the following step, a time domain analysis is carried out
to obtain the responses of the structure in the moored condition. In
this study, wave induced motions are only taken into consideration.
Wind and current loads are ruled out and shall be included in further
studies. For the current study, 2000 seconds simulation is taken. The
results represent wave induced motion responses, mooring line
tensions and identify critical mooring lines.
Abstract: We have aimed to produce a self-cleaning transparent
polymer coating with polyurethane (PU) matrix as the latter is highly
solvent, chemical and weather resistant having good mechanical
properties. Nano-silica modified by 1H, 1H, 2H, 2Hperflurooctyltriethoxysilane
was incorporated into the PU matrix for
attaining self-cleaning ability through hydrophobicity. The
modification was confirmed by particle size analysis and scanning
electron microscopy (SEM). Thermo-gravimetric (TGA) studies were
carried to ascertain the grafting of silane onto the silica. Several
coating formulations were prepared by varying the silica loading
content and compared to a commercial equivalent. The effect of
dispersion and the morphology of the coated films were assessed by
SEM analysis. All coating standardized tests like solvent resistance,
adhesion, flexibility, acid, alkali, gloss etc. have been performed as
per ASTM standards. Water contact angle studies were conducted to
analyze the hydrophobic character of the coating. In addition, the
coatings were also subjected to salt spray and accelerated weather
testing to analyze the durability of the coating.
Abstract: The present study investigates the effectiveness of
newly designed clayey pellets (fired clay pellets diameter sizes of 5
and 8 mm, and unfired clay pellets with the diameter size of 15 mm)
as the beds in the column adsorption process. The adsorption
experiments in the batch mode were performed before the column
experiment with the purpose to determine the order of adsorbent
package in the column which was to be designed in the investigation.
The column experiment was performed by using a known mass of the
clayey beds and the volume of the waste printing developer, which
was purified. The column was filled in the following order: fired clay
pellets of the diameter size of 5 mm, fired clay pellets of the diameter
size of 8 mm, and unfired clay pellets of the diameter size of 15 mm.
The selected order of the adsorbents showed a high removal
efficiency for zinc (97.8%) and copper (81.5%) ions. These
efficiencies were better than those in the case of the already existing
mode adsorption. The obtained experimental data present a good
basis for the selection of an appropriate column fill, but further
testing is necessary in order to obtain more accurate results.
Abstract: Purpose: The key aim of the research was to identify
the secondary stressors experienced by businesses affected by single
or repeated flooding and to determine to what extent businesses were
affected by these stressors, along with any resulting impact on health.
Additionally the research aimed to establish the likelihood of
businesses being re-exposed to the secondary stressors through
assessing awareness of flood risk, implementation of property
protection measures and level of community resilience. Design/methodology/approach: The chosen research method
involved the distribution of a questionnaire survey to businesses
affected by either single or repeated flood events. The questionnaire
included the Impact of Event Scale (a 15-item self-report measure
which assesses subjective distress caused by traumatic events). Findings: 55 completed questionnaires were returned by flood
impacted businesses. 89% of the businesses had sustained internal
flooding, while 11% had experienced external flooding. The results
established that the key secondary stressors experienced by
businesses, in order of priority, were: flood damage, fear of
reoccurring flooding, prevention of access to the premise/closure,
loss of income, repair works, length of closure and insurance issues.
There was a lack of preparedness for potential future floods and
consequent vulnerability to the emergence of secondary stressors
among flood affected businesses, as flood resistance or flood
resilience measures had only been implemented by 11% and 13%
respectively. In relation to the psychological repercussions, the
Impact of Event scores suggested that potential prevalence of posttraumatic
stress disorder (PTSD) was noted among 8 out of 55
respondents (l5%). Originality/value: The results improve understanding of the
enduring repercussions of flood events on businesses, indicating that
not only residents may be susceptible to the detrimental health
impacts of flood events and single flood events may be just as likely
as reoccurring flooding to contribute to ongoing stress. Lack of
financial resources is a possible explanation for the lack of
implementation of property protection measures among businesses,
despite 49% experiencing flooding on multiple occasions. Therefore
it is recommended that policymakers should consider potential
sources of financial support or grants towards flood defences for
flood impacted businesses. Any form of assistance should be made
available to businesses at the earliest opportunity as there was no
significant association between the time of the last flood event and
the likelihood of experiencing PTSD symptoms.
Abstract: Myoelectric control system is the fundamental
component of modern prostheses, which uses the myoelectric signals
from an individual’s muscles to control the prosthesis movements.
The surface electromyogram signal (sEMG) being noninvasive has
been used as an input to prostheses controllers for many years.
Recent technological advances has led to the development of
implantable myoelectric sensors which enable the internal
myoelectric signal (MES) to be used as input to these prostheses
controllers. The intramuscular measurement can provide focal
recordings from deep muscles of the forearm and independent signals
relatively free of crosstalk thus allowing for more independent
control sites. However, little work has been done to compare the two
inputs. In this paper we have compared the classification accuracy of
six pattern recognition based myoelectric controllers which use
surface myoelectric signals recorded using untargeted (symmetric)
surface electrode arrays to the same controllers with multichannel
intramuscular myolectric signals from targeted intramuscular
electrodes as inputs. There was no significant enhancement in the
classification accuracy as a result of using the intramuscular EMG
measurement technique when compared to the results acquired using
the surface EMG measurement technique. Impressive classification
accuracy (99%) could be achieved by optimally selecting only five
channels of surface EMG.
Abstract: A 15-storey RC building, studied in this paper, is
representative of modern building type constructed in Madina City in
Saudi Arabia before 10 years ago. These buildings are almost
consisting of reinforced concrete skeleton i.e. columns, beams and
flat slab as well as shear walls in the stairs and elevator areas
arranged in the way to have a resistance system for lateral loads
(wind – earthquake loads). In this study, the dynamic properties of
the 15-storey RC building were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Three dimensional pushover analysis (Nonlinear static
analysis) was carried out using SAP2000 software incorporating
inelastic material properties for concrete, infill and steel. The effect
of modeling the building with and without infill walls, on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madina area has been investigated. ATC-
40 capacity and demand spectra are utilized to get the modification
factor (R) for the studied building. The purpose of this analysis is to
evaluate the expected performance of structural systems by
estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results are summarized and discussed.
Abstract: The beginning of 21st century has witnessed new
advancements in the design and use of new materials for biosensing
applications, from nano to macro, protein to tissue. Traditional
analytical methods lack a complete toolset to describe the
complexities introduced by living systems, pathological relations,
discrete hierarchical materials, cross-phase interactions, and
structure-property dependencies. Materiomics – via systematic
molecular dynamics (MD) simulation – can provide structureprocess-
property relations by using a materials science approach
linking mechanisms across scales and enables oriented biosensor
design. With this approach, DNA biosensors can be utilized to detect
disease biomarkers present in individuals’ breath such as acetone for
diabetes. Our wireless sensor array based on single-stranded DNA
(ssDNA)-decorated single-walled carbon nanotubes (SWNT) has
successfully detected trace amount of various chemicals in vapor
differentiated by pattern recognition. Here, we present how MD
simulation can revolutionize the way of design and screening of DNA
aptamers for targeting biomarkers related to oral diseases and oral
health monitoring. It demonstrates great potential to be utilized to
build a library of DNDA sequences for reliable detection of several
biomarkers of one specific disease, and as well provides a new
methodology of creating, designing, and applying of biosensors.
Abstract: Teaching of mathematics to engineering students is an
open ended problem in education. The main goal of mathematics
learning for engineering students is the ability of applying a wide
range of mathematical techniques and skills in their engineering
classes and later in their professional work. Most of the
undergraduate engineering students and faculties feels that no efforts
and attempts are made to demonstrate the applicability of various
topics of mathematics that are taught thus making mathematics
unavoidable for some engineering faculty and their students. The lack
of understanding of concepts in engineering mathematics may hinder
the understanding of other concepts or even subjects. However, for
most undergraduate engineering students, mathematics is one of the
most difficult courses in their field of study. Most of the engineering students never understood mathematics or
they never liked it because it was too abstract for them and they could
never relate to it. A right balance of application and concept based
teaching can only fulfill the objectives of teaching mathematics to
engineering students. It will surely improve and enhance their
problem solving and creative thinking skills. In this paper, some practical (informal) ways of making
mathematics-teaching application based for the engineering students
is discussed. An attempt is made to understand the present state of
teaching mathematics in engineering colleges. The weaknesses and
strengths of the current teaching approach are elaborated. Some of
the causes of unpopularity of mathematics subject are analyzed and a
few pragmatic suggestions have been made. Faculty in mathematics
courses should spend more time discussing the applications as well as
the conceptual underpinnings rather than focus solely on strategies
and techniques to solve problems. They should also introduce more
‘word’ problems as these problems are commonly encountered in
engineering courses. Overspecialization in engineering education
should not occur at the expense of (or by diluting) mathematics and
basic sciences. The role of engineering education is to provide the
fundamental (basic) knowledge and to teach the students simple
methodology of self-learning and self-development. All these issues
would be better addressed if mathematics and engineering faculty
join hands together to plan and design the learning experiences for
the students who take their classes. When faculties stop competing
against each other and start competing against the situation, they will
perform better. Without creating any administrative hassles these
suggestions can be used by any young inexperienced faculty of
mathematics to inspire engineering students to learn engineering
mathematics effectively.
Abstract: The crossover probability and mutation probability are the two important factors in genetic algorithm. The adaptive genetic algorithm can improve the convergence performance of genetic algorithm, in which the crossover probability and mutation probability are adaptively designed with the changes of fitness value. We apply adaptive genetic algorithm into a function optimization problem. The numerical experiment represents that adaptive genetic algorithm improves the convergence speed and avoids local convergence.
Abstract: The simulation in wind tunnel is used thoroughly to model real situations of drainages of air. Besides the automotive industry, a great number of applications can be numbered: dispersion of pollutant, studies of pedestrians’ comfort, and dispersion of particles. This work had the objective of visualizing the characteristics aerodynamics of two automobiles in different ways. To accomplish that drainage of air a fan that generated a speed exists (measured with anemometer of hot thread) of 4,1m/s and 4,95m/s. To visualize the path of the air through the cars, in the wind tunnel, smoke was used, obtained with it burns of vegetable oil. For “to do smoke” vegetable oil was used, that was burned for a tension of 20V generated by a thread of 2,5mm. The cars were placed inside of the wind tunnel with the drainage of “air-smoke” and photographed, registering like this the path lines around them, in the 3 different speeds.
Abstract: The paper presents an additive manufacturing process for the production of metal and composite parts. It is termed as composite metal foil manufacturing and is a combination of laminated object manufacturing and brazing techniques. The process has been described in detail and is being used to produce dissimilar aluminum to copper foil single lap joints. A three dimensional finite element model has been developed to study the thermo-mechanical characteristics of the dissimilar Al/Cu single lap joint. The effects of thermal stress and strain have been analyzed by carrying out transient thermal analysis on the heated plates used to join the two 0.1mm thin metal foils. Tensile test has been carried out on the foils before joining and after the single Al/Cu lap joints are made, they are subjected to tensile lap-shear test to analyze the effect of heat on the foils. The analyses are designed to assess the mechanical integrity of the foils after the brazing process and understand whether or not the heat treatment has an effect on the fracture modes of the produced specimens.
Abstract: This paper presents a fault-tolerant implementation for
adder schemes using the dual duplication code. To prove the
efficiency of the proposed method, the circuit is simulated in double
pass transistor CMOS 32nm technology and some transient faults are
voluntary injected in the Layout of the circuit. This fully differential
implementation requires only 20 transistors which mean that the
proposed design involves 28.57% saving in transistor count
compared to standard CMOS technology.
Abstract: Geological structure formed by volcanic activities shows polymorphic characteristics due to repeated cooling and hardening of lava. The Jeju region is showing polymorphic characteristics in which clinker layers are irregularly distributed along with vesicular basalt due to volcanic activities. Accordingly, resident damages and environmental disputes occur frequently in the Jeju region due to blasting. The purpose of this study is to develop a blast vibration equation considering the polymorphic characteristics of basaltic ground in Jeju. The blast vibration equation consists of a functional formula of the blasting vibration constant K that changes according to ground characteristics, and attenuation index n. The case study results in Jeju showed that if there are clinker layers, attenuation index n showed a distribution of -1.32~-1.81, whereas if there are no clinker layers, n was -2.79. Moreover, if there are no clinker layers, the frequency of blast vibration showed a high frequency band from 30Hz to 100Hz, while in rocks with clinker layers it showed a low frequency band from 10Hz to 20Hz.
Abstract: In order to study the Mutual effect of genotype ×
environment for the percent of oil index in sunflower items, an
experiment was accomplished form complete random block designs
in four iteration and was four diverse researching station comprising
Esfahan, Birjand, Sari, and Karaj. Complex variance analysis showed
that there is an important diversity between the items under
investigation. The results relevant the coefficient variation of items
Azargol and Vidoc has respectively allocated the minimum
coefficient of variations. According to the results extrapolated from
Shokla stability variance, the Items Brocar, Allison and Fabiola, are
among the stable genotypes for oil percent respectively. In the biplot
GGE, the location under investigations divided in two superenvironments,
first one comprised of locations naming Esfahan,
Karaj, and Birjand, and second one were such a location as Sari. By
this point of view, in the first super-environment, the Item Fabiola
and in the second Almanzor item was among the best items and
crops.
Abstract: Nanofibers are defined as fibers with diameters less
than 100 nanometers. In this study, behaviours of activated carbon
nanofiber (ACNF), carbon nanofiber (CNF), polyacrylonitrile/ carbon
nanotube (PAN/CNT), polyvinyl alcohol/nanosilver (PVA/Ag) in
proton exchange membrane (PEM) fuel cells are investigated
experimentally. This material was used as gas diffusion layer (GDL)
in PEM fuel cells. In this study, the electrical conductivities of
nanofiber and nanofiber/nanoparticles have been studied to
understand their effects on PEM fuel cell performance. According to
the experimental results, the maximum electrical conductivity
performance of the fuel cell with nanofiber was found to be at
PVA/Ag (at UConn condition). The electrical conductivities of CNF,
ACNF, PAN/CNT are lower for PEM. The resistance of cell with
PVA/Ag is lower than the resistance of cell with PAN/CNT, ACNF,
CNF.
Abstract: The study of the aerodynamics related to the
improvement in the acting of airplanes and automobiles with the
objective of being reduced the effect of the attrition of the air on
structures, providing larger speeds and smaller consumption of fuel.
The application of the knowledge of the aerodynamics not more
limits to the aeronautical and automobile industries. Therefore, this
research aims to design and construction of a wind tunnel to perform
aerodynamic analysis in bodies of cars, seeking greater efficiency.
Therefore, this research aims to design and construction of a wind
tunnel to perform aerodynamic analysis in bodies of cars, seeking
greater efficiency. For this, a methodology for wind tunnel type
selection is designed to be built, taking into account the various
existing configurations in which chose to build an open circuit tunnel,
due to the lower complexity of construction and installation;
operational simplicity and low cost. The guidelines for the project
were teaching: the layer that limits study and analyze specimens with
different geometries. For the variation of pressure in the test, section
of a switched gauge used a pitot tube. Thus, it was possible to obtain
quantitative and qualitative results, which proved to be satisfactory.