Abstract: This paper presents a part of research on the
rheological properties of bitumen modified by thermoplastic namely
linear low density polyethylene (LLDPE), high density polyethylene
(HDPE) and polypropylene (PP) and its interaction with 80 pen base
bitumen. As it is known that the modification of bitumen by the use
of polymers enhances its performance characteristics but at the same
time significantly alters its rheological properties. The rheological
study of polymer modified bitumen (PMB) was made through
penetration, ring & ball softening point and viscosity test. The results
were then related to the changes in the rheological properties of
polymer modified bitumen. It was observed that thermoplastic
copolymer shows profound effect on penetration rather than
softening point. The viscoelastic behavior of polymer modified
bitumen depend on the concentration of polymer, mixing
temperature, mixing technique, solvating power of base bitumen and
molecular structure of polymer used. PP offer better blend in
comparison to HDPE and LLDPE. The viscosity of base bitumen was
also enhanced with the addition of polymer. The pseudoplastic
behavior was more prominent for HDPE and LLDPE than PP. Best
results were obtained when polymer concentration was kept below
3%
Abstract: Optical properties of sputter-deposited ZnS thin films
were investigated as potential replacements for CBD(chemical bath
deposition) CdS buffer layers in the application of CIGS solar cells.
ZnS thin films were fabricated on glass substrates at RT, 150oC, 200oC,
and 250oC with 50 sccm Ar gas using an RF magnetron sputtering
system. The crystal structure of the thin film is found to be zinc blende
(cubic) structure. Lattice parameter of ZnS is slightly larger than CdS
on the plane and thus better matched with that of CIGS. Within a
400-800 nm wavelength region, the average transmittance was larger
than 75%. When the deposition temperature of the thin film was
increased, the blue shift phenomenon was enhanced. Band gap energy
of the ZnS thin film tended to increase as the deposition temperature
increased. ZnS thin film is a promising material system for the CIGS
buffer layer, in terms of ease of processing, low cost, environmental
friendliness, higher transparency, and electrical properties
Abstract: Impact is one of very important subjects which always have been considered in mechanical science. Nature of impact is such that which makes its control a hard task. Therefore it is required to present the transfer of impact to other vulnerable part of a structure, when it is necessary, one of the best method of absorbing energy of impact, is by using Thin-walled tubes these tubes collapses under impact and with absorption of energy, it prevents the damage to other parts.Purpose of recent study is to survey the deformation and energy absorption of tubes with different type of cross section (rectangular or square) and with similar volumes, height, mean cross section thickness, and material under loading with different speeds. Lateral loading of tubes are quasi-static type and beside as numerical analysis, also experimental experiences has been performed to evaluate the accuracy of the results. Results from the surveys is indicates that in a same conditions which mentioned above, samples with square cross section ,absorb more energy compare to rectangular cross section, and also by increscent in speed of loading, energy absorption would be more.
Abstract: We prove detailed analysis of a waveguide-based Schottky barrier photodetector (SBPD) where a thin silicide film is put on the top of a silicon-on-insulator (SOI) channel waveguide to absorb light propagating along the waveguide. Taking both the confinement factor of light absorption and the wall scanning induced gain of the photoexcited carriers into account, an optimized silicide thickness is extracted to maximize the effective gain, thereby the responsivity. For typical lengths of the thin silicide film (10-20 Ðçm), the optimized thickness is estimated to be in the range of 1-2 nm, and only about 50-80% light power is absorbed to reach the maximum responsivity. Resonant waveguide-based SBPDs are proposed, which consist of a microloop, microdisc, or microring waveguide structure to allow light multiply propagating along the circular Si waveguide beneath the thin silicide film. Simulation results suggest that such resonant waveguide-based SBPDs have much higher repsonsivity at the resonant wavelengths as compared to the straight waveguidebased detectors. Some experimental results about Si waveguide-based SBPD are also reported.
Abstract: The procurement and cost management approach adopted for mechanical and electrical (M&E) services in Malaysian construction industry have been criticized for its inefficiency. The study examined early cost estimating practices adopted for mechanical and electrical services (M&E) in Malaysia so as to understand the level of compliance of the current techniques with best practices. The methodology adopted for the study is a review of bidding documents used on both completed and on – going building projects awarded between 2008 – 2010 under 9th Malaysian Plan. The analysis revealed that, M&E services cost cannot be reliably estimated at pre-contract stage; the bidding techniques adopted for M&E services failed to provide uniform basis for contractors to submit tender; detailed measurement of items were not made which could complicate post contract cost control and financial management. The paper concluded that, there is need to follow a structured approach in determining the pre-contract cost estimate for M&E services which will serve as a virile tool for post contract cost control.
Abstract: In the paper the results of calculations of the dynamic
response of a multi-storey reinforced concrete building to a strong
mining shock originated from the main region of mining activity in
Poland (i.e. the Legnica-Glogow Copper District) are presented. The
representative time histories of accelerations registered in three
directions were used as ground motion data in calculations of the
dynamic response of the structure. Two variants of a numerical model
were applied: the model including only structural elements of the
building and the model including both structural and non-structural
elements (i.e. partition walls and ventilation ducts made of brick). It
turned out that non-structural elements of multi-storey RC buildings
have a small impact of about 10 % on natural frequencies of these
structures. It was also proved that the dynamic response of building
to mining shock obtained in case of inclusion of all non-structural
elements in the numerical model is about 20 % smaller than in case
of consideration of structural elements only. The principal stresses
obtained in calculations of dynamic response of multi-storey building
to strong mining shock are situated on the level of about 30% of
values obtained from static analysis (dead load).
Abstract: Oxidative stress is considered to be the cause for onset
and the progression of type 2 diabetes mellitus (T2DM) and
complications including neuropathy. It is a deleterious process that
can be an important mediator of damage to cell structures: protein,
lipids and DNA. Data suggest that in patients with diabetes and
diabetic neuropathy DNA repair is impaired, which prevents effective
removal of lesions. Objective: The aim of our study was to evaluate
the association of the hOGG1 (326 Ser/Cys) and XRCC1 (194
Arg/Trp, 399 Arg/Gln) gene polymorphisms whose protein is
involved in the BER pathway with DNA repair efficiency in patients
with diabetes type 2 and diabetic neuropathy compared to the healthy
subjects. Genotypes were determined by PCR-RFLP analysis in 385
subjects, including 117 with type 2 diabetes, 56 with diabetic
neuropathy and 212 with normal glucose metabolism. The
polymorphisms studied include codon 326 of hOGG1 and 194, 399
of XRCC1 in the base excision repair (BER) genes. Comet assay was
carried out using peripheral blood lymphocytes from the patients and
controls. This test enabled the evaluation of DNA damage in cells
exposed to hydrogen peroxide alone and in the combination with the
endonuclease III (Nth). The results of the analysis of polymorphism
were statistically examination by calculating the odds ratio (OR) and
their 95% confidence intervals (95% CI) using the ¤ç2-tests. Our data
indicate that patients with diabetes mellitus type 2 (including those
with neuropathy) had higher frequencies of the XRCC1 399Arg/Gln
polymorphism in homozygote (GG) (OR: 1.85 [95% CI: 1.07-3.22],
P=0.3) and also increased frequency of 399Gln (G) allele (OR: 1.38
[95% CI: 1.03-1.83], P=0.3). No relation to other polymorphisms
with increased risk of diabetes or diabetic neuropathy. In T2DM
patients complicated by neuropathy, there was less efficient repair of
oxidative DNA damage induced by hydrogen peroxide in both the
presence and absence of the Nth enzyme. The results of our study
suggest that the XRCC1 399 Arg/Gln polymorphism is a significant
risk factor of T2DM in Polish population. Obtained data suggest a
decreased efficiency of DNA repair in cells from patients with
diabetes and neuropathy may be associated with oxidative stress.
Additionally, patients with neuropathy are characterized by even
greater sensitivity to oxidative damage than patients with diabetes,
which suggests participation of free radicals in the pathogenesis of
neuropathy.
Abstract: Expression data analysis is based mostly on the
statistical approaches that are indispensable for the study of
biological systems. Large amounts of multidimensional data resulting
from the high-throughput technologies are not completely served by
biostatistical techniques and are usually complemented with visual,
knowledge discovery and other computational tools. In many cases,
in biological systems we only speculate on the processes that are
causing the changes, and it is the visual explorative analysis of data
during which a hypothesis is formed. We would like to show the
usability of multidimensional visualization tools and promote their
use in life sciences. We survey and show some of the
multidimensional visualization tools in the process of data
exploration, such as parallel coordinates and radviz and we extend
them by combining them with the self-organizing map algorithm. We
use a time course data set of transitional cell carcinoma of the bladder
in our examples. Analysis of data with these tools has the potential to
uncover additional relationships and non-trivial structures.
Abstract: Starting from a biologically inspired framework, Gabor filters were built up from retinal filters via LMSE algorithms. Asubset of retinal filter kernels was chosen to form a particular Gabor filter by using a weighted sum. One-dimensional optimization approaches were shown to be inappropriate for the problem. All model parameters were fixed with biological or image processing constraints. Detailed analysis of the optimization procedure led to the introduction of a minimization constraint. Finally, quantization of weighting factors was investigated. This resulted in an optimized cascaded structure of a Gabor filter bank implementation with lower computational cost.
Abstract: In this experimental investigation shake table tests
were conducted on two reduced models that represent normal single
room building constructed by Compressed Stabilized Earth Block
(CSEB) from locally available soil. One model was constructed with
earthquake resisting features (EQRF) having sill band, lintel band and
vertical bands to control the building vibration and another one was
without Earthquake Resisting Features. To examine the seismic
capacity of the models particularly when it is subjected to long-period
ground motion by large amplitude by many cycles of repeated
loading, the test specimen was shaken repeatedly until the failure.
The test results from Hi-end Data Acquisition system show that
model with EQRF behave better than without EQRF. This modified
masonry model with new material combined with new bands is used
to improve the behavior of masonry building.
Abstract: Reinforced Concrete (RC) structures strengthened
with fiber reinforced polymer (FRP) lack in thermal resistance under
elevated temperatures in the event of fire. This phenomenon led to
the lining of strengthened concrete with thin high performance
cementitious composites (THPCC) to protect the substrate against
elevated temperature. Elevated temperature effects on THPCC, based
on different cementitious materials have been studied in the past but
high-alumina cement (HAC)-based THPCC have not been well
characterized. This research study will focus on the THPCC based on
HAC replaced by 60%, 70%, 80% and 85% of ground granulated
blast furnace slag (GGBS). Samples were evaluated by the
measurement of their mechanical strength (28 & 56 days of curing)
after exposed to 400°C, 600°C and 28°C of room temperature for
comparison and corroborated by their microstructure study. Results
showed that among all mixtures, the mix containing only HAC
showed the highest compressive strength after exposed to 600°C as
compared to other mixtures. However, the tensile strength of THPCC
made of HAC and 60% GGBS content was comparable to the
THPCC with HAC only after exposed to 600°C. Field emission
scanning electron microscopy (FESEM) images of THPCC
accompanying Energy Dispersive X-ray (EDX) microanalysis
revealed that the microstructure deteriorated considerably after
exposure to elevated temperatures which led to the decrease in
mechanical strength.
Abstract: One of the best ways for achievement of conventional
vehicle changing to hybrid case is trustworthy simulation result and
using of driving realities. For this object, in this paper, at first sevendegree-
of-freedom dynamical model of vehicle will be shown. Then
by using of statically model of engine, gear box, clutch, differential,
electrical machine and battery, the hybrid automobile modeling will
be down and forward simulation of vehicle for pedals to wheels
power transformation will be obtained. Then by design of a fuzzy
controller and using the proper rule base, fuel economy and
regenerative braking will be marked. Finally a series of
MATLAB/SIMULINK simulation results will be proved the
effectiveness of proposed structure.
Abstract: As the web continues to grow exponentially, the idea
of crawling the entire web on a regular basis becomes less and less
feasible, so the need to include information on specific domain,
domain-specific search engines was proposed. As more information
becomes available on the World Wide Web, it becomes more difficult
to provide effective search tools for information access. Today,
people access web information through two main kinds of search
interfaces: Browsers (clicking and following hyperlinks) and Query
Engines (queries in the form of a set of keywords showing the topic
of interest) [2]. Better support is needed for expressing one's
information need and returning high quality search results by web
search tools. There appears to be a need for systems that do reasoning
under uncertainty and are flexible enough to recover from the
contradictions, inconsistencies, and irregularities that such reasoning
involves. In a multi-view problem, the features of the domain can be
partitioned into disjoint subsets (views) that are sufficient to learn the
target concept. Semi-supervised, multi-view algorithms, which
reduce the amount of labeled data required for learning, rely on the
assumptions that the views are compatible and uncorrelated. This
paper describes the use of semi-structured machine learning approach
with Active learning for the “Domain Specific Search Engines". A
domain-specific search engine is “An information access system that
allows access to all the information on the web that is relevant to a
particular domain. The proposed work shows that with the help of
this approach relevant data can be extracted with the minimum
queries fired by the user. It requires small number of labeled data and
pool of unlabelled data on which the learning algorithm is applied to
extract the required data.
Abstract: Nozzle is the main part of various spinning systems
such as air-jet and Murata air vortex systems. Recently, many
researchers worked on the usage of the nozzle on different spinning
systems such as conventional ring and compact spinning systems. In
these applications, primary purpose is to improve the yarn quality. In
present study, it was produced the yarns with two different nozzle
types and determined the changes in yarn properties. In order to
explain the effect of the nozzle, airflow structure in the nozzle was
modelled and airflow variables were determined. In numerical
simulation, ANSYS 12.1 package program and Fluid Flow (CFX)
analysis method was used. As distinct from the literature, Shear
Stress Turbulent (SST) model is preferred. And also air pressure at
the nozzle inlet was measured by electronic mass flow meter and
these values were used for the simulation of the airflow. At last, the
yarn was modelled and the area from where the yarn is passing was
included to the numerical analysis.
Abstract: The study investigated the practices of organisations in Gulf Cooperation Council (GCC) countries with regards to G2C egovernment maturity. It reveals that e-government G2C initiatives in the surveyed countries in particular, and arguably around the world in general, are progressing slowly because of the lack of a trusted and secure medium to authenticate the identities of online users. The authors conclude that national ID schemes will play a major role in helping governments reap the benefits of e-government if the three advanced technologies of smart card, biometrics and public key infrastructure (PKI) are utilised to provide a reliable and trusted authentication medium for e-government services.
Abstract: A minimal complexity version of component mode
synthesis is presented that requires simplified computer
programming, but still provides adequate accuracy for modeling
lower eigenproperties of large structures and their transient
responses. The novelty is that a structural separation into components
is done along a plane/surface that exhibits rigid-like behavior, thus
only normal modes of each component is sufficient to use, without
computing any constraint, attachment, or residual-attachment modes.
The approach requires only such input information as a few (lower)
natural frequencies and corresponding undamped normal modes of
each component. A novel technique is shown for formulation of
equations of motion, where a double transformation to generalized
coordinates is employed and formulation of nonproportional damping
matrix in generalized coordinates is shown.
Abstract: This study proposes a basic molecular formula for all
proteins. A total of 10,739 proteins belonging to 9 different protein
groups classified on the basis of their functions were selected
randomly. They included enzymes, storage proteins, hormones,
signalling proteins, structural proteins, transport proteins,
immunoglobulins or antibodies, motor proteins and receptor proteins.
After obtaining the protein molecular formula using the ProtParam
tool, the H/C, N/C, O/C, and S/C ratios were determined for each
randomly selected sample. In this case, H, N, O, and S coefficients
were specified per carbon atom. Surprisingly, the results
demonstrated that H, N, O, and S coefficients for all 10,739 proteins
are similar and highly correlated. This study demonstrates that
despite differences in the structure and function, all known proteins
have a similar basic molecular formula CnH1.58 ± 0.015nN0.28 ± 0.005nO0.30
± 0.007nS0.01 ± 0.002n. The total correlation between all coefficients was
found to be 0.9999.
Abstract: This paper proposes an effective adaptation learning
algorithm based on artificial neural networks for speed control of an
induction motor assumed to operate in a high-performance drives
environment. The structure scheme consists of a neural network
controller and an algorithm for changing the NN weights in order that
the motor speed can accurately track of the reference command. This
paper also makes uses a very realistic and practical scheme to
estimate and adaptively learn the noise content in the speed load
torque characteristic of the motor. The availability of the proposed
controller is verified by through a laboratory implementation and
under computation simulations with Matlab-software. The process is
also tested for the tracking property using different types of reference
signals. The performance and robustness of the proposed control
scheme have evaluated under a variety of operating conditions of the
induction motor drives. The obtained results demonstrate the
effectiveness of the proposed control scheme system performances,
both in steady state error in speed and dynamic conditions, was found
to be excellent and those is not overshoot.
Abstract: In modern agriculture, polymeric hydrogels are
known as a component able to hold an amount of water due to their
3-dimensional network structure and their tendency to absorb water
in humid environments. In addition, these hydrogels are able to
controllably release the fertilisers and pesticides loaded in them.
Therefore, they deliver these materials to the plants' roots and help
them with growing. These hydrogels also reduce the pollution of
underground water sources by preventing the active components
from leaching. In this study, sIPN acrylamide based hydrogels are
synthesised by using acrylamide free radical, potassium acrylate, and
linear polyvinyl alcohol. Ammonium nitrate is loaded in the hydrogel
as the fertiliser. The effect of various amounts of monomers and
linear polymer, measured in molar ratio, on the swelling rate,
equilibrium swelling, and release of ammonium nitrate is studied.
Abstract: In this paper we propose an intelligent agent approach
to control the electric power grid at a smaller granularity in order to
give it self-healing capabilities. We develop a method using the
influence model to transform transmission substations into
information processing, analyzing and decision making (intelligent
behavior) units. We also develop a wireless communication method
to deliver real-time uncorrupted information to an intelligent
controller in a power system environment. A combined networking
and information theoretic approach is adopted in meeting both the
delay and error probability requirements. We use a mobile agent
approach in optimizing the achievable information rate vector and in
the distribution of rates to users (sensors). We developed the concept
and the quantitative tools require in the creation of cooperating semiautonomous
subsystems which puts the electric grid on the path
towards intelligent and self-healing system.