Abstract: Textures of AZ31 Mg alloy sheets were evaluated by using neutron diffraction method in this study. The AZ31 sheets were fabricated either by conventional casting and subsequent hot rolling or strip casting. The effect of warm rolling was investigated using the AZ31 Mg alloy sheet produced by conventional casting. Warm rolling of 30% thickness reduction per pass was possible without any side-crack at temperatures as low as 200oC under the roll speed of 30 m/min. The initial microstructure of conventionally cast specimen was found to be partially recrystallized structures. Grain refinement was found to occur actively during the warm rolling. The (0002),(10-10) (10-11),and (10-12) complete pole figures were measured using the HANARO FCD (Neutron Four Circle Diffractometer) and ODF were calculated. The major texture of all specimens can be expressed by ND//(0001) fiber texture. Texture of hot rolled specimen showed the strongest fiber component, while that of strip cast sheet seemed to be similar to random distribution.
Abstract: In this article, a new inexact alternating direction method(ADM) is proposed for solving a class of variational inequality problems. At each iteration, the new method firstly solves the resulting subproblems of ADM approximately to generate an temporal point ˜xk, and then the multiplier yk is updated to get the new iterate yk+1. In order to get xk+1, we adopt a new descent direction which is simple compared with the existing prediction-correction type ADMs. For the inexact ADM, the resulting proximal subproblem has closedform solution when the proximal parameter and inexact term are chosen appropriately. We show the efficiency of the inexact ADM numerically by some preliminary numerical experiments.
Abstract: This paper investigates the impact on operating time delay and relay maloperation when 1st,2nd and 3rd order analog antialiasing filters are used in numerical distance protection. RC filter with cut-off frequency 90 Hz is used. Simulations are carried out for different SIR (Source to line Impedance Ratio), load, fault type and fault conditions using SIMULINK, where the voltage and current signals are fed online to the developed numerical distance relay model. Matlab is used for plotting the impedance trajectory. Investigation results shows that, about 75 % of the simulated cases, numerical distance relay operating time is not increased even-though there is a time delay when higher order filters are used. Relay maloperation (selectivity) also reduces (increases) when higher order filters are used in numerical distance protection.
Abstract: Psychoacoustics has become a potential area of research due to the growing interest of both laypersons and medical and mental health professionals. Non invasive brain computer interface like Electroencephalography (EEG) is widely being used in this field. An attempt has been made in this paper to examine the response of EEG signals to acoustic stimuli further analyzing the brain electrical activity. The real time EEG is acquired for 6 participants using a cost effective and portable EMOTIV EEG neuro headset. EEG data analysis is further done using EMOTIV test bench, EDF browser and EEGLAB (MATLAB Tool) application software platforms. Spectral analysis of acquired neural signals (AF3 channel) using these software platforms are clearly indicative of increased brain activity in various bands. The inferences drawn from such an analysis have significant correlation with subject’s subjective reporting of the experiences. The results suggest that the methodology adopted can further be used to assist patients with sleeping and depressive disorders.
Abstract: High Resolution NMR Spectroscopy offers unique screening capabilities for food quality and safety by combining non-targeted and targeted screening in one analysis.
The objective is to demonstrate, that due to its extreme reproducibility NMR can detect smallest changes in concentrations of many components in a mixture, which is best monitored by statistical evaluation however also delivers reliable quantification results.
The methodology typically uses a 400 MHz high resolution instrument under full automation after minimized sample preparation.
For example one fruit juice analysis in a push button operation takes at maximum 15 minutes and delivers a multitude of results, which are automatically summarized in a PDF report.
The method has been proven on fruit juices, where so far unknown frauds could be detected. In addition conventional targeted parameters are obtained in the same analysis. This technology has the advantage that NMR is completely quantitative and concentration calibration only has to be done once for all compounds. Since NMR is so reproducible, it is also transferable between different instruments (with same field strength) and laboratories. Based on strict SOP`s, statistical models developed once can be used on multiple instruments and strategies for compound identification and quantification are applicable as well across labs.
Abstract: Coastal zone combines terrestrial, marine and atmospheric factors and gives rise to unique landforms that play an important role in long-term sustainability of the hinterland and economy of maritime nations. World over, efforts have been put forth to understand plants of the seacoasts. In India also, plants of several geographical entities have been well documented, but works devoted to plant communities of the vast tropical coast of India and its States are still insufficient. Therefore, an inventory of plants flourishing in a stretch of ~450km of the Coastal Regulatory Zone I encompassing a total of 84 villages in 6 revenue Districts of northern Andhra Pradesh (15o42’06”N, 80o51’03”E to 19o05’51”N, 84o47’44”E) along Bay of Bengal was carried out. The study revealed presence of a total of 364 species belonging to 225 genera under 71 families. In addition to inventory, zonation pattern, ethnobotany, and certain interesting ecological facts are included.
Abstract: The current Hadoop block placement policy do not fairly and evenly distributes replicas of blocks written to datanodes in a Hadoop cluster.
This paper presents a new solution that helps to keep the cluster in a balanced state while an HDFS client is writing data to a file in Hadoop cluster. The solution had been implemented, and test had been conducted to evaluate its contribution to Hadoop distributed file system.
It has been found that, the solution has lowered global execution time taken by Hadoop balancer to 22 percent. It also has been found that, Hadoop balancer respectively over replicate 1.75 and 3.3 percent of all re-distributed blocks in the modified and original Hadoop clusters.
The feature that keeps the cluster in a balanced state works as a core part to Hadoop system and not just as a utility like traditional balancer. This is one of the significant achievements and uniqueness of the solution developed during the course of this research work.
Abstract: This paper investigates the suitability of Latin Hypercube sampling (LHS) for composite electric power system reliability analysis. Each sample generated in LHS is mapped into an equivalent system state and used for evaluating the annualized system and load point indices. DC loadflow based state evaluation model is solved for each sampled contingency state. The indices evaluated are loss of load probability, loss of load expectation, expected demand not served and expected energy not supplied. The application of the LHS is illustrated through case studies carried out using RBTS and IEEE-RTS test systems. Results obtained are compared with non-sequential Monte Carlo simulation and state enumeration analytical approaches. An error analysis is also carried out to check the LHS method’s ability to capture the distributions of the reliability indices. It is found that LHS approach estimates indices nearer to actual value and gives tighter bounds of indices than non-sequential Monte Carlo simulation.
Abstract: This study focused on the estimation of carbon released to the atmosphere from dry dipterocarp forest (DDF) fires in Thailand. Laboratory experiments were conducted using a cone calorimeter to simulate the DDF fires. The leaf litter collected from DDF in western Thailand was used as biomass fuel. Three different masses of leaf litter were employed, 7g, 10g and 13g, to estimate the carbon released from this type of vegetation fire to the atmosphere. The chemical analysis of the leaf litter showed that the carbon content in the experimental biomass fuel was 46.0±0.1%. From the experiments, it was found that more than 95% of the carbon input was converted to carbon released to the atmosphere, while less than 5% were left in the form of residues, and returned to soil. From the study, the carbon released amounted 440.213±2.243 g/kgdry biomass, and the carbon retained in the residues was 19.786±2.243 g/kgdry biomass. The quantity of biomass fuel consumed to produce 1 g of carbon released was 2.27±0.01gkgdry biomass. Using these experimental data of carbon produced by the DDF fires, it was estimated that this type of fires in 2009 contributed to 4.659 tonnes of carbon released to the atmosphere, and 0.229 tonnes of carbon in the residues to be returned to soil in Thailand.
Abstract: We have investigated statistical properties of the defect turbulence in 1D CGLE wherein many body interaction is involved between local depressing wave (LDW) and local standing wave (LSW). It is shown that the counting number fluctuation of LDW is subject to the sub-Poisson statistics (SUBP). The physical origin of the SUBP can be ascribed to pair extinction of LDWs based on the master equation approach. It is also shown that the probability density function (pdf) of inter-LDW distance can be identified by the hyper gamma distribution. Assuming a superstatistics of the exponential distribution (Poisson configuration), a plausible explanation is given. It is shown further that the pdf of amplitude of LDW has a fattail. The underlying mechanism of its fluctuation is examined by introducing a generalized fractional Poisson configuration.
Abstract: An efficient reintegration of the disabled people in the
family and society should be fulfilled; hence it is strongly needful to assist their diminished functions or to replace the totally lost
functions. Assistive technology helps in neutralizing the impairment.
Recent advancements in embedded systems have opened up a vast
area of research and development for affordable and portable assistive devices for the visually impaired. Granted there are many assistive devices on the market that are able to detect obstacles, and numerous research and development currently in process to
alleviate the cause, unfortunately the cost of devices, size of
devices, intrusiveness and higher learning curve prevents the visually impaired from taking advantage of available devices. This
project aims at the design and implementation of a detachable unit
which is robust, low cost and user friendly, thus, trying to
aggrandize the functionality of the existing white cane, to concede above-knee obstacle detection. The designed obstruction detector
uses ultrasound sensors for detecting the obstructions before direct contact. It bestows haptic feedback to the user in accordance with the position of the obstacle.
Abstract: When faced with stochastic networks with an uncertain
duration for their activities, the securing of network completion time
becomes problematical, not only because of the non-identical pdf of
duration for each node, but also because of the interdependence of
network paths. As evidenced by Adlakha & Kulkarni [1], many
methods and algorithms have been put forward in attempt to resolve
this issue, but most have encountered this same large-size network
problem. Therefore, in this research, we focus on network reduction
through a Series/Parallel combined mechanism. Our suggested
algorithm, named the Activity Network Reduction Algorithm
(ANRA), can efficiently transfer a large-size network into an S/P
Irreducible Network (SPIN). SPIN can enhance stochastic network
analysis, as well as serve as the judgment of symmetry for the Graph
Theory.
Abstract: The objective of this study was to determine the
effects of garlic oil (Allium sativa), turmeric powder (Curcuma longa
Linn) and Monensin on Total apparent digestibility of nutrients in
Baloochi lambs. The experiment was designed as a 4 x 4 Latin square
using 4 ruminally baloochi lambs with 4 treatments in four 28-d
periods. Treatments were control (no additive), garlic oil (0. 4 g/d),
monensin (0. 2 g/d) and turmeric powder (20 g/d). Total apparent
digestibility's (% of intake) of organic matter (OM), dry matter (DM),
crud protein (CP), ether extract(EE), non fiber carbohydrate (NFC),
acid detergent fiber (ADF) and neutral detergent fiber (NDF) in the
total tract were not influenced by addition of either additives.
Abstract: In this paper, we present a non-blind technique of
adding the watermark to the Fourier spectral components of audio
signal in a way such that the modified amplitude does not exceed the
maximum amplitude spread (MAS). This MAS is due to individual
Discrete fourier transform (DFT) coefficients in that particular frame,
which is derived from the Energy Spreading function given by
Schroeder. Using this technique one can store double the information
within a given frame length i.e. overriding the watermark on the
host of equal length with least perceptual distortion. The watermark
is uniformly floating on the DFT components of original signal.
This helps in detecting any intentional manipulations done on the
watermarked audio. Also, the scheme is found robust to various signal
processing attacks like presence of multiple watermarks, Additive
white gaussian noise (AWGN) and mp3 compression.
Abstract: In the 1980s, companies began to feel the effect of three major influences on their product development: newer and innovative technologies, increasing product complexity and larger organizations. And therefore companies were forced to look for new product development methods. This paper tries to focus on the two of new product development methods (DFM and CE). The aim of this paper is to see and analyze different product development methods specifically on Design for Manufacturability and Concurrent Engineering. Companies can achieve and be benefited by minimizing product life cycle, cost and meeting delivery schedule. This paper also presents simplified models that can be modified and used by different companies based on the companies- objective and requirements. Methodologies that are followed to do this research are case studies. Two companies were taken and analysed on the product development process. Historical data, interview were conducted on these companies in addition to that, Survey of literatures and previous research works on similar topics has been done during this research. This paper also tries to show the implementation cost benefit analysis and tries to calculate the implementation time. From this research, it has been found that the two companies did not achieve the delivery time to the customer. Some of most frequently coming products are analyzed and 50% to 80 % of their products are not delivered on time to the customers. The companies are following the traditional way of product development that is sequentially design and production method, which highly affect time to market. In the case study it is found that by implementing these new methods and by forming multi disciplinary team in designing and quality inspection; the company can reduce the workflow steps from 40 to 30.
Abstract: A new and cost effective RP-HPLC method was
developed and validated for simultaneous analysis of non steroidal
anti inflammatory dugs Diclofenac sodium (DFS), Flurbiprofen
(FLP) and an opioid analgesic Tramadol (TMD) in advanced drug
delivery systems (Liposome and Microcapsules), marketed brands
and human plasma. Isocratic system was employed for the flow of
mobile phase consisting of 10 mM sodium dihydrogen phosphate
buffer and acetonitrile in molar ratio of 67: 33 with adjusted pH of
3.2. The stationary phase was hypersil ODS column (C18, 250×4.6
mm i.d., 5 μm) with controlled temperature of 30 C°. DFS in
liposomes, microcapsules and marketed drug products was
determined in range of 99.76-99.84%. FLP and TMD in
microcapsules and brands formulation were 99.78 - 99.94 % and
99.80 - 99.82 %, respectively. Single step liquid-liquid extraction
procedure using combination of acetonitrile and trichloroacetic acid
(TCA) as protein precipitating agent was employed. The detection
limits (at S/N ratio 3) of quality control solutions and plasma samples
were 10, 20, and 20 ng/ml for DFS, FLP and TMD, respectively.
The Assay was acceptable in linear dynamic range. All other
validation parameters were found in limits of FDA and ICH method
validation guidelines. The proposed method is sensitive, accurate and
precise and could be applicable for routine analysis in
pharmaceutical industry as well as in human plasma samples for
bioequivalence and pharmacokinetics studies.
Abstract: A novel application of neural network approach to
fault classification and fault location of Medium voltage cables is
demonstrated in this paper. Different faults on a protected cable
should be classified and located correctly. This paper presents the use
of neural networks as a pattern classifier algorithm to perform these
tasks. The proposed scheme is insensitive to variation of different
parameters such as fault type, fault resistance, and fault inception
angle. Studies show that the proposed technique is able to offer high
accuracy in both of the fault classification and fault location tasks.
Abstract: A block backward differentiation formula of uniform
order eight is proposed for solving first order stiff initial value
problems (IVPs). The conventional 8-step Backward Differentiation
Formula (BDF) and additional methods are obtained from the same
continuous scheme and assembled into a block matrix equation which
is applied to provide the solutions of IVPs on non-overlapping
intervals. The stability analysis of the method indicates that the
method is L0-stable. Numerical results obtained using the proposed
new block form show that it is attractive for solutions of stiff problems
and compares favourably with existing ones.
Abstract: A new design approach for three-stage operational
amplifiers (op-amps) is proposed. It allows to actually implement a
symmetrical push-pull class-AB amplifier output stage for wellestablished
three-stage amplifiers using a feedforward
transconductance stage. Compared with the conventional design
practice, the proposed approach leads to a significant
improvement of the symmetry between the positive and the
negative op-amp step response, resulting in similar values of the
positive/negative settling time. The new approach proves to be very
useful in order to fully exploit the potentiality allowed by the op-amp
in terms of speed performances. Design examples in a commercial
0.35-μm CMOS prove the effectiveness of theproposed strategy.
Abstract: Liners are made to protect the groundwater table from
the infiltration of leachate which normally carries different kinds of
toxic materials from landfills. Although these liners are engineered to
last for long period of time; unfortunately these liners fail; therefore,
toxic materials pass to groundwater. This paper focuses on the
changes of the hydraulic conductivity of a sand-bentonite liner due to
the infiltration of biofuel and ethanol fuel. Series of laboratory tests
were conducted in 20-cm-high PVC columns. Several compositions
of sand-bentonite liners were tested: 95% sand: 5% bentonite; 90%
sand: 10% bentonite; and 100% sand (passed mesh #40). The
columns were subjected to extreme pressures of 40 kPa, and 100 kPa
to evaluate the transport of alternative fuels (biofuel and ethanol
fuel). For comparative studies, similar tests were carried out using
water. Results showed that hydraulic conductivity increased due to
the infiltration of alternative fuels through the liners. Accordingly,
the increase in the hydraulic conductivity showed significant
dependency on the type of liner mixture and the characteristics of the
liquid. The hydraulic conductivity of a liner (subjected to biofuel
infiltration) consisting of 5% bentonite: 95% sand under pressure of
40 kPa and 100 kPa had increased by one fold. In addition, the
hydraulic conductivity of a liner consisting of 10% bentonite: 90%
sand under pressure of 40 kPa and 100 kPa and infiltrated by biofuel
had increased by three folds. On the other hand, the results obtained
by water infiltration under 40 kPa showed lower hydraulic
conductivities of 1.50×10-5 and 1.37×10-9 cm/s for 5% bentonite:
95% sand, and 10% bentonite: 90% sand, respectively. Similarly,
under 100 kPa, the hydraulic conductivities were 2.30×10-5 and
1.90×10-9 cm/s for 5% bentonite: 95% sand, and 10% bentonite: 90%
sand, respectively.