Abstract: Design for cost (DFC) is a method that reduces life
cycle cost (LCC) from the angle of designers. Multiple domain
features mapping (MDFM) methodology was given in DFC. Using
MDFM, we can use design features to estimate the LCC. From the
angle of DFC, the design features of family cars were obtained, such
as all dimensions, engine power and emission volume. At the
conceptual design stage, cars- LCC were estimated using back
propagation (BP) artificial neural networks (ANN) method and
case-based reasoning (CBR). Hamming space was used to measure the
similarity among cases in CBR method. Levenberg-Marquardt (LM)
algorithm and genetic algorithm (GA) were used in ANN. The
differences of LCC estimation model between CBR and artificial
neural networks (ANN) were provided. ANN and CBR separately
each method has its shortcomings. By combining ANN and CBR
improved results accuracy was obtained. Firstly, using ANN selected
some design features that affect LCC. Then using LCC estimation
results of ANN could raise the accuracy of LCC estimation in CBR
method. Thirdly, using ANN estimate LCC errors and correct errors in
CBR-s estimation results if the accuracy is not enough accurate.
Finally, economically family cars and sport utility vehicle (SUV) was
given as LCC estimation cases using this hybrid approach combining
ANN and CBR.
Abstract: Opportunistic Data Forwarding (ODF) has drawn much attention in mobile adhoc networking research in recent years. The effectiveness of ODF in MANET depends on a suitable routing protocol which provides a powerful source routing services. PLSR is featured by source routing, loop free and small routing overhead. The update messages in PLSR are integrated into a tree structure and no need to time stamp routing updates which reduces the routing overhead.
Abstract: This paper deals with condition monitoring of electric switch machine for railway points. Point machine, as a complex electro-mechanical device, switch the track between two alternative routes. There has been an increasing interest in railway safety and the optimal management of railway equipments maintenance, e.g. point machine, in order to enhance railway service quality and reduce system failure. This paper explores the development of Kolmogorov- Smirnov (K-S) test to detect some point failures (external to the machine, slide chairs, fixing, stretchers, etc), while the point machine (inside the machine) is in its proper condition. Time-domain stator Current signatures of normal (healthy) and faulty points are taken by 3 Hall Effect sensors and are analyzed by K-S test. The test is simulated by creating three types of such failures, namely putting a hard stone and a soft stone between stock rail and switch blades as obstacles and also slide chairs- friction. The test has been applied for those three faults which the results show that K-S test can effectively be developed for the aim of other point failures detection, which their current signatures deviate parametrically from the healthy current signature. K-S test as an analysis technique, assuming that any defect has a specific probability distribution. Empirical cumulative distribution functions (ECDF) are used to differentiate these probability distributions. This test works based on the null hypothesis that ECDF of target distribution is statistically similar to ECDF of reference distribution. Therefore by comparing a given current signature (as target signal) from unknown switch state to a number of template signatures (as reference signal) from known switch states, it is possible to identify which is the most likely state of the point machine under analysis.
Abstract: The equilibrium chemical reactions taken place in a converter reactor of the Khorasan Petrochemical Ammonia plant was studied using the minimization of Gibbs free energy method. In the minimization of the Gibbs free energy function the Davidon– Fletcher–Powell (DFP) optimization procedure using the penalty terms in the well-defined objective function was used. It should be noted that in the DFP procedure along with the corresponding penalty terms the Hessian matrices for the composition of constituents in the Converter reactor can be excluded. This, in fact, can be considered as the main advantage of the DFP optimization procedure. Also the effect of temperature and pressure on the equilibrium composition of the constituents was investigated. The results obtained in this work were compared with the data collected from the converter reactor of the Khorasan Petrochemical Ammonia plant. It was concluded that the results obtained from the method used in this work are in good agreement with the industrial data. Notably, the algorithm developed in this work, in spite of its simplicity, takes the advantage of short computation and convergence time.
Abstract: Wavelength multiplexing (WDM) technology along
with optical amplifiers is used for optical communication systems in
S-band, C-band and L-band. To improve the overall system
performance Hybrid amplifiers consisting of cascaded TDFA and
EDFA with different gain bandwidths are preferred for long haul
wavelength multiplexed optical communication systems. This paper
deals with statistical analysis of different configuration of hybrid
amplifier i.e. analysis of TDFA-EDFA configuration and EDFA –
TDFA configuration. In this paper One-Way ANOVA method is used
for statistical analysis.
Abstract: This paper aims at to develop a robust optimization methodology for the mechatronic modules of machine tools by considering all important characteristics from all structural and control domains in one single process. The relationship between these two domains is strongly coupled. In order to reduce the disturbance caused by parameters in either one, the mechanical and controller design domains need to be integrated. Therefore, the concurrent integrated design method Design For Control (DFC), will be employed in this paper. In this connect, it is not only applied to achieve minimal power consumption but also enhance structural performance and system response at same time. To investigate the method for integrated optimization, a mechatronic feed drive system of the machine tools is used as a design platform. Pro/Engineer and AnSys are first used to build the 3D model to analyze and design structure parameters such as elastic deformation, nature frequency and component size, based on their effects and sensitivities to the structure. In addition, the robust controller,based on Quantitative Feedback Theory (QFT), will be applied to determine proper control parameters for the controller. Therefore, overall physical properties of the machine tool will be obtained in the initial stage. Finally, the technology of design for control will be carried out to modify the structural and control parameters to achieve overall system performance. Hence, the corresponding productivity is expected to be greatly improved.
Abstract: One of the major disadvantages of the minimally
invasive surgery (MIS) is the lack of tactile feedback to the surgeon.
In order to identify and avoid any damage to the grasped complex
tissue by endoscopic graspers, it is important to measure the local
softness of tissue during MIS. One way to display the measured
softness to the surgeon is a graphical method. In this paper, a new
tactile sensor has been reported. The tactile sensor consists of an
array of four softness sensors, which are integrated into the jaws of a
modified commercial endoscopic grasper. Each individual softness
sensor consists of two piezoelectric polymer Polyvinylidene Fluoride
(PVDF) films, which are positioned below a rigid and a compliant
cylinder. The compliant cylinder is fabricated using a micro molding
technique. The combination of output voltages from PVDF films is
used to determine the softness of the grasped object. The theoretical
analysis of the sensor is also presented.
A method has been developed with the aim of reproducing the
tactile softness to the surgeon by using a graphical method. In this
approach, the proposed system, including the interfacing and the data
acquisition card, receives signals from the array of softness sensors.
After the signals are processed, the tactile information is displayed
by means of a color coding method. It is shown that the degrees of
softness of the grasped objects/tissues can be visually differentiated
and displayed on a monitor.
Abstract: The present project was conducted with the
circumferential-fuel-jets inverse diffusion flame (CIDF) burner
burning liquefied petroleum gas (LPG) enriched with 50% of
hydrogen fuel (H2). The range of stable operation of the CIDF burner
in terms of Reynolds number (from laminar to turbulent flow regions),
equivalence ratio and fuel jet velocity of LPG of the 50% H2-LPG
mixed fuel was identified. Experiments were also carried out to
investigate the flame structures of the LPG flame and LPG enriched H2
flame. Experimental results obtained from these two flames were
compared to fully explore the influence of hydrogen addition on flame
stability. Flame heights obtained by burning these two kinds of fuels at
various equivalence ratios were compared and correlated with the
Global Momentum Ratio (GMR).
Abstract: Understanding patient factors related to physical activity behavior is important in the management of Type 2 Diabetes. This study applied the Theory of Planned Behavior model to understand physical activity behavior among sampled Type 2 diabetics in Kenya. The study was conducted within the diabetic clinic at Kisii Level 5 Hospital and adopted sequential mixed methods design beginning with qualitative phase and ending with quantitative phase. Qualitative data was analyzed using grounded theory analysis method. Structural equation modeling using maximum likelihood was used to analyze quantitative data. The common fit indices revealed that the theory of planned behavior fitted the data acceptably well among the Type 2 diabetes and within physical activity behavior {¤ç2 = 213, df = 84, n=230, p = .061, ¤ç2/df = 2.53; TLI = .97; CFI =.96; RMSEA (90CI) = .073(.029, .08)}. This theory proved to be useful in understanding physical activity behavior among Type 2 diabetics.
Abstract: This paper presents the modeling and simulation of a hybrid proton exchange membrane fuel cell (PEMFC) with an energy storage system for use in a stand-alone distributed generation (DG) system. The simulation model consists of fuel cell DG, lead-acid battery, maximum power point tracking and power conditioning unit which is modeled in the MATLAB/Simulink platform. Poor loadfollowing characteristics and slow response to rapid load changes are some of the weaknesses of PEMFC because of the gas processing reaction and the fuel cell dynamics. To address the load-tracking issues in PEMFC, a hybrid PEMFC and battery storage system is considered and modelled. The model utilizes PEMFC as the main energy source whereas the battery functions as energy storage to compensate for the limitations of PEMFC.Simulation results are given to show the overall system performance under light and heavyloading conditions.
Abstract: The Reverse Monte Carlo (RMC) simulation is applied in the study of an aqueous electrolyte LiCl6H2O. On the basis of the available experimental neutron scattering data, RMC computes pair radial distribution functions in order to explore the structural features of the system. The obtained results include some unrealistic features. To overcome this problem, we use the Hybrid Reverse Monte Carlo (HRMC), incorporating an energy constraint in addition to the commonly used constraints derived from experimental data. Our results show a good agreement between experimental and computed partial distribution functions (PDFs) as well as a significant improvement in pair partial distribution curves. This kind of study can be considered as a useful test for a defined interaction model for conventional simulation techniques.
Abstract: Doubly fed induction machines DFIM are used
mainly for wind energy conversion in MW power plants. This paper
presents a new strategy of field oriented control ,it is based on the
principle of a double flux orientation of stator and rotor at the same
time. Therefore, the orthogonality created between the two oriented
fluxes, which must be strictly observed, leads to generate a linear and
decoupled control with an optimal torque. The obtained simulation
results show the feasibility and the effectiveness of the suggested
method.
Abstract: Nano-MgO was successfully deposited on titania using deposition-precipitation method. The catalyst produced was characterised using FTIR, XRD, BET and XRF and its activity was tested on the transesterification reaction of soybean oil to biodiesel. The catalyst activity improved when the reaction temperature was increasedfrom 150 and 225 OC. It was also observed that increasing the reaction time above 1h had no significant benefit on conversion. The stability fixed MgO on TiO2 was investigated using XRF and ICP-OES. It was observed that MgO loss during the reaction was between 0.5-2.3 percent and that there was no correlation between the reaction temperature and the MgO loss.
Abstract: Signal processing applications which are iterative in
nature are best represented by data flow graphs (DFG). In these
applications, the maximum sampling frequency is dependent on the
topology of the DFG, the cyclic dependencies in particular. The
determination of the iteration bound, which is the reciprocal of the
maximum sampling frequency, is critical in the process of hardware
implementation of signal processing applications. In this paper, a
novel technique to compute the iteration bound is proposed. This
technique is different from all previously proposed techniques, in the
sense that it is based on the natural flow of tokens into the DFG
rather than the topology of the graph. The proposed algorithm has
lower run-time complexity than all known algorithms. The
performance of the proposed algorithm is illustrated through
analytical analysis of the time complexity, as well as through
simulation of some benchmark problems.
Abstract: In the oil and gas industry, energy prediction can help
the distributor and customer to forecast the outgoing and incoming
gas through the pipeline. It will also help to eliminate any
uncertainties in gas metering for billing purposes. The objective of
this paper is to develop Neural Network Model for energy
consumption and analyze the performance model. This paper
provides a comprehensive review on published research on the
energy consumption prediction which focuses on structures and the
parameters used in developing Neural Network models. This paper is
then focused on the parameter selection of the neural network
prediction model development for energy consumption and analysis
on the result. The most reliable model that gives the most accurate
result is proposed for the prediction. The result shows that the
proposed neural network energy prediction model is able to
demonstrate an adequate performance with least Root Mean Square
Error.
Abstract: Investigation of soil properties like Cation Exchange
Capacity (CEC) plays important roles in study of environmental
reaserches as the spatial and temporal variability of this property
have been led to development of indirect methods in estimation of
this soil characteristic. Pedotransfer functions (PTFs) provide an
alternative by estimating soil parameters from more readily available
soil data. 70 soil samples were collected from different horizons of
15 soil profiles located in the Ziaran region, Qazvin province, Iran.
Then, multivariate regression and neural network model (feedforward
back propagation network) were employed to develop a
pedotransfer function for predicting soil parameter using easily
measurable characteristics of clay and organic carbon. The
performance of the multivariate regression and neural network model
was evaluated using a test data set. In order to evaluate the models,
root mean square error (RMSE) was used. The value of RMSE and
R2 derived by ANN model for CEC were 0.47 and 0.94 respectively,
while these parameters for multivariate regression model were 0.65
and 0.88 respectively. Results showed that artificial neural network
with seven neurons in hidden layer had better performance in
predicting soil cation exchange capacity than multivariate regression.
Abstract: This paper presents a mean for reducing the torque
variation during the revolution of a vertical-axis wind turbine
(VAWT) by increasing the blade number. For this purpose, twodimensional
CDF analysis have been performed on a straight-bladed
Darreius-type rotor. After describing the computational model, a
complete campaign of simulations based on full RANS unsteady
calculations is proposed for a three, four and five-bladed rotor
architecture characterized by a NACA 0025 airfoil. For each
proposed rotor configuration, flow field characteristics are
investigated at several values of tip speed ratio, allowing a
quantification of the influence of blade number on flow geometric
features and dynamic quantities, such as rotor torque and power.
Finally, torque and power curves are compared for the analyzed
architectures, achieving a quantification of the effect of blade number
on overall rotor performance.
Abstract: This paper presents performance analysis of the
Evolutionary Programming-Artificial Neural Network (EPANN)
based technique to optimize the architecture and training parameters
of a one-hidden layer feedforward ANN model for the prediction of
energy output from a grid connected photovoltaic system. The ANN
utilizes solar radiation and ambient temperature as its inputs while the
output is the total watt-hour energy produced from the grid-connected
PV system. EP is used to optimize the regression performance of the
ANN model by determining the optimum values for the number of
nodes in the hidden layer as well as the optimal momentum rate and
learning rate for the training. The EPANN model is tested using two
types of transfer function for the hidden layer, namely the tangent
sigmoid and logarithmic sigmoid. The best transfer function, neural
topology and learning parameters were selected based on the highest
regression performance obtained during the ANN training and testing
process. It is observed that the best transfer function configuration for
the prediction model is [logarithmic sigmoid, purely linear].
Abstract: Generation of electricity from coal has increased over
the years in the United States and around the world. Burning of coal
results in annual production of upwards of 100 millions tons (United
States only) of coal combustion products (CCPs). Only about a third
of these products are being used to create new products while the
remainder goes to landfills. Application of CCPs mixed with
composted organic materials onto soil can improve the soil-s
physico-chemical conditions and provide essential plant nutritients.
Our objective was to create plant growth media utilizing CCPs and
compost in way which maximizes the use of these products and, at
the same time, maintain good plant growth. Media were formulated
by adding composted organic matter (COM) to CCPs at ratios
ranging from 2:8 to 8:2 (v/v). The quality of these media was
evaluated by measuring their physical and chemical properties and
their effect on plant growth. We tested the media by 1) measuring
their physical and chemical properties and 2) the growth of three
plant species in the experimental media: wheat (Triticum sativum),
tomato (Lycopersicum esculentum) and marigold (Tagetes patula).
We achieved significantly (p < 0.001) higher growth (7-130%) in the
experimental media containing CCPs compared to a commercial mix.
The experimental media supplied adequate plant nutrition as no
fertilization was provided during the experiment. Based on the
results, we recommend the use of CCPs and composts for the
creation of plant growth media.
Abstract: The lecture represents significant advances in
understanding of the transfer processes mechanism in turbulent
separated flows. Based upon experimental data suggesting the
governing role of generated local pressure gradient that takes place in
the immediate vicinity of the wall in separated flow as a result of
intense instantaneous accelerations induced by large-scale vortex
flow structures similarity laws for mean velocity and temperature and
spectral characteristics and heat and mass transfer law for turbulent
separated flows have been developed. These laws are confirmed by
available experimental data. The results obtained were employed for
analysis of heat and mass transfer in some very complex processes
occurring in technological applications such as impinging jets, heat
transfer of cylinders in cross flow and in tube banks, packed beds
where processes manifest distinct properties which allow them to be
classified under turbulent separated flows. Many facts have got an
explanation for the first time.