Abstract: This research proposes an algorithm for the simulation
of time-periodic unsteady problems via the solution unsteady Euler
and Navier-Stokes equations. This algorithm which is called Time
Spectral method uses a Fourier representation in time and hence
solve for the periodic state directly without resolving transients
(which consume most of the resources in a time-accurate scheme).
Mathematical tools used here are discrete Fourier transformations. It
has shown tremendous potential for reducing the computational cost
compared to conventional time-accurate methods, by enforcing
periodicity and using Fourier representation in time, leading to
spectral accuracy. The accuracy and efficiency of this technique is
verified by Euler and Navier-Stokes calculations for pitching airfoils.
Because of flow turbulence nature, Baldwin-Lomax turbulence
model has been used at viscous flow analysis. The results presented
by the Time Spectral method are compared with experimental data. It
has shown tremendous potential for reducing the computational cost
compared to the conventional time-accurate methods, by enforcing
periodicity and using Fourier representation in time, leading to
spectral accuracy, because results verify the small number of time
intervals per pitching cycle required to capture the flow physics.
Abstract: This paper presents the averaging model of a buck
converter derived from the generalized state-space averaging method.
The sliding mode control is used to regulate the output voltage of the
converter and taken into account in the model. The proposed model
requires the fast computational time compared with those of the full
topology model. The intensive time-domain simulations via the exact
topology model are used as the comparable model. The results show
that a good agreement between the proposed model and the switching
model is achieved in both transient and steady-state responses. The
reported model is suitable for the optimal controller design by using
the artificial intelligence techniques.
Abstract: This paper describes a finite-difference time-domainFDTD) method to analyze lightning surge propagation in electric transmission lines. Numerical computation of solving the Telegraphist-s equations is determined and investigated its effectiveness. A source of lightning surge wave on power transmission lines is modeled by using Heidler-s surge model. The
proposed method was tested against medium-voltage power
transmission lines in comparison with the solution obtained by using
lattice diagram. As a result, the calculation showed that the method is one of accurate methods to analyze transient
lightning wave in power transmission lines.
Abstract: The recent advances in computational fluid dynamics
(CFD) can be useful in observing the detailed hemodynamics in
cerebral aneurysms for understanding not only their formation and
rupture but also for clinical evaluation and treatment. However,
important hemodynamic quantities are difficult to measure in vivo. In
the present study, an approximate model of normal middle cerebral
artery (MCA) along with two cases consisting broad and narrow
saccular aneurysms are analyzed. The models are generated in
ANSYS WORKBENCH and transient analysis is performed in
ANSYS-CFX. The results obtained are compared for three cases and
agree well with the available literature.
Abstract: A method has been developed for preparing load
models for power flow and stability. The load modeling
(LOADMOD) computer software transforms data on load class mix,
composition, and characteristics into the from required for
commonly–used power flow and transient stability simulation
programs. Typical default data have been developed for load
composition and characteristics. This paper defines LOADMOD
software and describes the dynamic and static load modeling
techniques used in this software and results of initial testing for
BAKHTAR power system.
Abstract: This paper presents a numerical investigation of the
unsteady flow around an American 19th century vertical-axis
windmill: the Stevens & Jolly rotor, patented on April 16, 1895. The
computational approach used is based on solving the complete
transient Reynolds-Averaged Navier-Stokes (t-RANS) equations: a
full campaign of numerical simulation has been performed using the
k-ω SST turbulence model. Flow field characteristics have been
investigated for several values of tip speed ratio and for a constant
unperturbed free-stream wind velocity of 6 m/s, enabling the study of
some unsteady flow phenomena in the rotor wake. Finally, the global
power generated from the windmill has been determined for each
simulated angular velocity, allowing the calculation of the rotor
power-curve.
Abstract: In this paper a new method for increasing the speed of
SAGCM-APD is proposed. Utilizing carrier rate equations in
different regions of the structure, a circuit model for the structure is
obtained. In this research, in addition to frequency response, the
effect of added new charge layer on some transient parameters like
slew-rate, rising and falling times have been considered. Finally, by
trading-off among some physical parameters such as different layers
widths and droppings, a noticeable decrease in breakdown voltage
has been achieved. The results of simulation, illustrate some features
of proposed structure improvement in comparison with conventional
SAGCM-APD structures.
Abstract: In this paper, the authors take a look at advantages of
multiphase induction motors comparing them with three phase ones
and present the applications where six-phase induction motors are
used. They elaborate the mathematical model of six-phase induction
motor with two similar stator three phase winding, shifted by 30
degrees in space and three phase winding in rotor, in synchronous
reference frame for soft starting and scalar control. The authors
simulate and discuss results of speed and torque starting transients.
Abstract: The paper considers a single-server queue with fixedsize
batch Poisson arrivals and exponential service times, a model
that is useful for a buffer that accepts messages arriving as fixed size
batches of packets and releases them one packet at time. Transient
performance measures for queues have long been recognized as
being complementary to the steady-state analysis. The focus of the
paper is on the use of the functions that arise in the analysis of the
transient behaviour of the queuing system. The paper exploits
practical modelling to obtain a solution to the integral equation
encountered in the analysis. Results obtained indicate that under
heavy load conditions, there is significant disparity in the statistics
between the transient and steady state values.
Abstract: Reduction of Single Input Single Output (SISO) discrete systems into lower order model, using a conventional and an evolutionary technique is presented in this paper. In the conventional technique, the mixed advantages of Modified Cauer Form (MCF) and differentiation are used. In this method the original discrete system is, first, converted into equivalent continuous system by applying bilinear transformation. The denominator of the equivalent continuous system and its reciprocal are differentiated successively, the reduced denominator of the desired order is obtained by combining the differentiated polynomials. The numerator is obtained by matching the quotients of MCF. The reduced continuous system is converted back into discrete system using inverse bilinear transformation. In the evolutionary technique method, Particle Swarm Optimization (PSO) is employed to reduce the higher order model. PSO method is based on the minimization of the Integral Squared Error (ISE) between the transient responses of original higher order model and the reduced order model pertaining to a unit step input. Both the methods are illustrated through numerical example.
Abstract: A transient finite element model has been developed
to study the heat transfer and fluid flow during spot Gas Tungsten
Arc Welding (GTAW) on stainless steel. Temperature field, fluid
velocity and electromagnetic fields are computed inside the cathode,
arc-plasma and anode using a unified MHD formulation. The
developed model is then used to study the influence of different
helium-argon gas mixtures on both the energy transferred to the
workpiece and the time evolution of the weld pool dimensions. It is
found that the addition of helium to argon increases the heat flux
density on the weld axis by a factor that can reach 6.5. This induces
an increase in the weld pool depth by a factor of 3. It is also found
that the addition of only 10% of argon to helium decreases
considerably the weld pool depth, which is due to the electrical
conductivity of the mixture that increases significantly when argon is
added to helium.
Abstract: Based on a theoretical erbium-doped fiber amplifier
(EDFA) model, we have proposed an application of disturbance
observer(DOB) with proportional/integral/differential(PID) controller
to EDFA for minimizing gain-transient time of wavelength
-division-multiplexing (WDM) multi channels in optical amplifier in
channel add/drop networks. We have dramatically reduced the
gain-transient time to less than 30μsec by applying DOB with PID
controller to the control of amplifier gain. The proposed DOB-based
gain control algorithm for EDFA was implemented as a digital control
system using TI's DSP(TMS320C28346) chip and experimental
results of the system verify the excellent performance of the proposed
gain control methodology.
Abstract: The paper presents a one-dimensional transient
mathematical model of thermal oil-water two-phase emulsion flows
in pipes. The set of the mass, momentum and enthalpy conservation
equations for the continuous fluid and droplet phases are solved. Two
friction correlations for the continuous fluid phase to wall friction are
accounted for in the model and tested. The aerodynamic drag force
between the continuous fluid phase and droplets is modeled, too. The
density and viscosity of both phases are assumed to be constant due
to adiabatic experimental conditions. The proposed mathematical
model is validated on the experimental measurements of oil-water
emulsion flows in horizontal pipe [1,2]. Numerical analysis on
single- and two-phase oil-water flows in a pipe is presented in the
paper. The continuous oil flow having water droplets is simulated.
Predictions, which are performed by using the presented model, show
excellent agreement with the experimental data if the water fraction is
equal or less than 10%. Disagreement between simulations and
measurements is increased if the water fraction is larger than 10%.
Abstract: In this paper, real-coded genetic algorithm (RCGA) optimization technique has been applied for large-scale linear dynamic multi-input-multi-output (MIMO) system. The method is based on error minimization technique where the integral square error between the transient responses of original and reduced order models has been minimized by RCGA. The reduction procedure is simple computer oriented and the approach is comparable in quality with the other well-known reduction techniques. Also, the proposed method guarantees stability of the reduced model if the original high-order MIMO system is stable. The proposed approach of MIMO system order reduction is illustrated with the help of an example and the results are compared with the recently published other well-known reduction techniques to show its superiority.
Abstract: In this paper are illustrated the principal aspects
connected with the numerical evaluation of thermal stress induced by high gradient temperature in the concrete beam. The reinforced concrete beam has many advantages over steel
beam, such as high resistance to high temperature, high resistance to thermal shock, Better resistance to fatigue and buckling, strong
resistance against, fire, explosion, etc.
The main drawback of the reinforced concrete beam is its poor resistance to tensile stresses. In order to investigate the thermal
induced tensile stresses, a numerical model of a transient thermal
analysis is presented for the evaluation of thermo-mechanical
response of concrete beam to the high temperature, taking into account the temperature dependence of the thermo physical properties of the concrete like thermal conductivity and specific heat.
Abstract: Transmission and distribution lines are vital links between the generating unit and consumers. They are exposed to atmosphere, hence chances of occurrence of fault in transmission line is very high which has to be immediately taken care of in order to minimize damage caused by it. In this paper Discrete wavelet transform of voltage signals at the two ends of transmission lines have been analyzed. The transient energy of the detail information of level five is calculated for different fault conditions. It is observed that the variation of transient energy of healthy and faulted line can give important information which can be very useful in classifying and locating the fault.
Abstract: In the analysis of structures, the nonlinear effects due to large displacement, large rotation and materially-nonlinear are very important and must be considered for the reliable analysis. The non-linear fmite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of fmite element code using the standard Galerkin weighted residual formulation. Two-dimensional plane stress model was carried out to present the shear wall response. Total Lagangian formulation, which is computationally more effective, is used in the formulation of stiffness matrices and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The details of the program formulation are highlighted and the results of the analyses are presented, along with a comparison of the response of the structure with Ansys software results. The presented model in this paper can be developed for nonlinear analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: This paper proposes transient angle stability
agents to enhance power system stability. The proposed transient
angle stability agents divided into two strategy agents. The
first strategy agent is a prediction agent that will predict power
system instability. According to the prediction agent-s output,
the second strategy agent, which is a control agent, is automatically
calculating the amount of active power reduction that can
stabilize the system and initiating a control action. The control
action considered is turbine fast valving. The proposed strategies
are applied to a realistic power system, the IEEE 50-
generator system. Results show that the proposed technique can
be used on-line for power system instability prediction and control.
Abstract: The aim of this paper is to develop a new two dimensional time accurate Euler solver for shock tube applications. The solver was developed to study the performance of a newly built short-duration hypersonic test facility at Universiti Tenaga Nasional “UNITEN" in Malaysia. The facility has been designed, built, and commissioned for different values of diaphragm pressure ratios in order to get wide range of Mach number. The developed solver uses second order accurate cell-vertex finite volume spatial discretization and forth order accurate Runge-Kutta temporal integration and it is designed to simulate the flow process for similar driver/driven gases (e.g. air-air as working fluids). The solver is validated against analytical solution and experimental measurements in the high speed flow test facility. Further investigations were made on the flow process inside the shock tube by using the solver. The shock wave motion, reflection and interaction were investigated and their influence on the performance of the shock tube was determined. The results provide very good estimates for both shock speed and shock pressure obtained after diaphragm rupture. Also detailed information on the gasdynamic processes over the full length of the facility is available. The agreements obtained have been reasonable.
Abstract: This paper presents features that characterize power
quality disturbances from recorded voltage waveforms using wavelet
transform. The discrete wavelet transform has been used to detect
and analyze power quality disturbances. The disturbances of interest
include sag, swell, outage and transient. A power system network has
been simulated by Electromagnetic Transients Program. Voltage
waveforms at strategic points have been obtained for analysis, which
includes different power quality disturbances. Then wavelet has been
chosen to perform feature extraction. The outputs of the feature
extraction are the wavelet coefficients representing the power quality
disturbance signal. Wavelet coefficients at different levels reveal the
time localizing information about the variation of the signal.