Abstract: The fixed partial dentures are mainly used in the frontal
part of the dental arch because of their great esthetics. There are
several factors that are associated with the stress state created in
ceramic restorations, including: thickness of ceramic layers,
mechanical properties of the materials, elastic modulus of the
supporting substrate material, direction, magnitude and frequency of
applied load, size and location of occlusal contact areas, residual
stresses induced by processing or pores, restoration-cement
interfacial defects and environmental defects. The purpose of this
study is to evaluate the capability of Polarization Sensitive Optical
Coherence Tomography (PSOCT) in detection and analysis of
possible material defects in metal-ceramic and integral ceramic fixed
partial dentures. As a conclusion, it is important to have a non
invasive method to investigate fixed partial prostheses before their
insertion in the oral cavity in order to satisfy the high stress
requirements and the esthetic function.
Abstract: The influence of twist arrangement on the temperature
distribution in an annular diffuser fitted with twisted rectangular hub
is investigated. Different pitches (Y = 120 mm, 100 mm, 80 mm, and
60 mm) for the twist arrangements are simulated to be compared. The
geometry of the annular diffuser and the inlet condition for the hub
arrangements are kept constant. The result reveals that using twisted
rectangular hub insert with different pitches will force the
temperature to distribute in a circular direction. However,
temperature distribution will be enhanced with the length pitch
increases.
Abstract: Both the minimum energy consumption and
smoothness, which is quantified as a function of jerk, are generally
needed in many dynamic systems such as the automobile and the
pick-and-place robot manipulator that handles fragile equipments.
Nevertheless, many researchers come up with either solely
concerning on the minimum energy consumption or minimum jerk
trajectory. This research paper proposes a simple yet very interesting
relationship between the minimum direct and indirect jerks
approaches in designing the time-dependent system yielding an
alternative optimal solution. Extremal solutions for the cost functions
of direct and indirect jerks are found using the dynamic optimization
methods together with the numerical approximation. This is to allow
us to simulate and compare visually and statistically the time history
of control inputs employed by minimum direct and indirect jerk
designs. By considering minimum indirect jerk problem, the
numerical solution becomes much easier and yields to the similar
results as minimum direct jerk problem.
Abstract: In recent years, fast neural networks for object/face detection have been introduced based on cross correlation in the frequency domain between the input matrix and the hidden weights of neural networks. In our previous papers [3,4], fast neural networks for certain code detection was introduced. It was proved in [10] that for fast neural networks to give the same correct results as conventional neural networks, both the weights of neural networks and the input matrix must be symmetric. This condition made those fast neural networks slower than conventional neural networks. Another symmetric form for the input matrix was introduced in [1-9] to speed up the operation of these fast neural networks. Here, corrections for the cross correlation equations (given in [13,15,16]) to compensate for the symmetry condition are presented. After these corrections, it is proved mathematically that the number of computation steps required for fast neural networks is less than that needed by classical neural networks. Furthermore, there is no need for converting the input data into symmetric form. Moreover, such new idea is applied to increase the speed of neural networks in case of processing complex values. Simulation results after these corrections using MATLAB confirm the theoretical computations.
Abstract: Mobile ad-hoc networks (MANETs) are a form of
wireless networks which do not require a base station for providing
network connectivity. Mobile ad-hoc networks have many
characteristics which distinguish them from other wireless networks
which make routing in such networks a challenging task. Cluster
based routing is one of the routing schemes for MANETs in which
various clusters of mobile nodes are formed with each cluster having
its own clusterhead which is responsible for routing among clusters.
In this paper we have proposed and implemented a distributed
weighted clustering algorithm for MANETs. This approach is based
on combined weight metric that takes into account several system
parameters like the node degree, transmission range, energy and
mobility of the nodes. We have evaluated the performance of
proposed scheme through simulation in various network situations.
Simulation results show that proposed scheme outperforms the
original distributed weighted clustering algorithm (DWCA).
Abstract: This paper presents a study on the thermodynamics
and transport properties of hot potassium carbonate aqueous system
(HPC) using electrolyte non-random two liquid, (ELECNRTL)
model. The operation conditions are varied to determine the system
liquid phase stability range at the standard and critical conditions. A
case study involving 30 wt% K2CO3, H2O standard system at
pressure of 1 bar and temperature range from 280.15 to 366.15 K has
been studied. The estimated solubility index, viscosity, water
activity, and density which obtained from the simulation showed a
good agreement with the experimental work. Furthermore, the
saturation temperature of the solution has been estimated.
Abstract: This paper presents the doping profile measurement
and characterization technique for the pocket implanted nano scale
n-MOSFET. Scanning capacitance microscopy and atomic force
microscopy have been used to image the extent of lateral dopant
diffusion in MOS structures. The data are capacitance vs. voltage
measurements made on a nano scale device. The technique is nondestructive
when imaging uncleaved samples. Experimental data from
the published literature are presented here on actual, cleaved device
structures which clearly indicate the two-dimensional dopant profile
in terms of a spatially varying modulated capacitance signal. Firstorder
deconvolution indicates the technique has much promise for
the quantitative characterization of lateral dopant profiles. The pocket
profile is modeled assuming the linear pocket profiles at the source
and drain edges. From the model, the effective doping concentration
is found to use in modeling and simulation results of the various
parameters of the pocket implanted nano scale n-MOSFET. The
potential of the technique to characterize important device related
phenomena on a local scale is also discussed.
Abstract: To understand working features of a micro combustor,
a computer code has been developed to study combustion of
hydrogen–air mixture in a series of chambers with same shape aspect
ratio but various dimensions from millimeter to micrometer level.
The prepared algorithm and the computer code are capable of
modeling mixture effects in different fluid flows including chemical
reactions, viscous and mass diffusion effects. The effect of various
heat transfer conditions at chamber wall, e.g. adiabatic wall, with
heat loss and heat conduction within the wall, on the combustion is
analyzed. These thermal conditions have strong effects on the
combustion especially when the chamber dimension goes smaller and
the ratio of surface area to volume becomes larger.
Both factors, such as larger heat loss through the chamber wall
and smaller chamber dimension size, may lead to the thermal
quenching of micro-scale combustion. Through such systematic
numerical analysis, a proper operation space for the micro-combustor
is suggested, which may be used as the guideline for microcombustor
design. In addition, the results reported in this paper
illustrate that the numerical simulation can be one of the most
powerful and beneficial tools for the micro-combustor design,
optimization and performance analysis.
Abstract: This paper presents a new adaptive DMC controller
that improves the controller performance in case of plant-model
mismatch. The new controller monitors the plant measured output,
compares it with the model output and calculates weights applied to
the controller move. Simulations show that the new controller can
help improve control performance and avoid instability in case of
severe model mismatches.
Abstract: This paper deals with the application of artificial
neural network (ANN) and fuzzy based Adaptive Neuro Fuzzy
Inference System(ANFIS) approach to Load Frequency Control
(LFC) of multi unequal area hydro-thermal interconnected power
system. The proposed ANFIS controller combines the advantages of
fuzzy controller as well as quick response and adaptability nature of
ANN. Area-1 and area-2 consists of thermal reheat power plant
whereas area-3 and area-4 consists of hydro power plant with electric
governor. Performance evaluation is carried out by using intelligent
controller like ANFIS, ANN and Fuzzy controllers and conventional
PI and PID control approaches. To enhance the performance of
intelligent and conventional controller sliding surface is included.
The performances of the controllers are simulated using
MATLAB/SIMULINK package. A comparison of ANFIS, ANN,
Fuzzy, PI and PID based approaches shows the superiority of
proposed ANFIS over ANN & fuzzy, PI and PID controller for 1%
step load variation.
Abstract: This paper presents a new method for estimating the mean curve of impulse voltage waveforms that are recorded during impulse tests. In practice, these waveforms are distorted by noise, oscillations and overshoot. The problem is formulated as an estimation problem. Estimation of the current signal parameters is achieved using a fast and accurate technique. The method is based on discrete dynamic filtering algorithm (DDF). The main advantage of the proposed technique is its ability in producing the estimates in a very short time and at a very high degree of accuracy. The algorithm uses sets of digital samples of the recorded impulse waveform. The proposed technique has been tested using simulated data of practical waveforms. Effects of number of samples and data window size are studied. Results are reported and discussed.
Abstract: A robot simulator was developed to measure and
investigate the performance of a robot navigation system based on
the relative position of the robot with respect to random obstacles in
any two dimensional environment. The presented simulator focuses
on investigating the ability of a fuzzy-neural system for object
avoidance. A navigation algorithm is proposed and used to allow
random navigation of a robot among obstacles when the robot faces
an obstacle in the environment. The main features of this simulator
can be used for evaluating the performance of any system that can
provide the position of the robot with respect to obstacles in the
environment. This allows a robot developer to investigate and
analyze the performance of a robot without implementing the
physical robot.
Abstract: An electric power system includes a generating, a
transmission, a distribution, and consumers subsystems. An electrical
power network in Tanzania keeps growing larger by the day and
become more complex so that, most utilities have long wished for
real-time monitoring and remote control of electrical power system
elements such as substations, intelligent devices, power lines,
capacitor banks, feeder switches, fault analyzers and other physical
facilities. In this paper, the concept of automation of management of
power systems from generation level to end user levels was
determined by using Power System Simulator for Engineering
(PSS/E) version 30.3.2.
Abstract: The Maximum Weighted Independent Set (MWIS)
problem is a classic graph optimization NP-hard problem. Given an
undirected graph G = (V, E) and weighting function defined on the
vertex set, the MWIS problem is to find a vertex set S V whose total
weight is maximum subject to no two vertices in S are adjacent. This
paper presents a novel approach to approximate the MWIS of a graph
using minimum weighted vertex cover of the graph. Computational
experiments are designed and conducted to study the performance
of our proposed algorithm. Extensive simulation results show that
the proposed algorithm can yield better solutions than other existing
algorithms found in the literature for solving the MWIS.
Abstract: This paper presents the work of signal discrimination
specifically for Electrocardiogram (ECG) waveform. ECG signal is
comprised of P, QRS, and T waves in each normal heart beat to
describe the pattern of heart rhythms corresponds to a specific
individual. Further medical diagnosis could be done to determine any
heart related disease using ECG information. The emphasis on QRS
Complex classification is further discussed to illustrate the
importance of it. Pan-Tompkins Algorithm, a widely known
technique has been adapted to realize the QRS Complex
classification process. There are eight steps involved namely
sampling, normalization, low pass filter, high pass filter (build a band
pass filter), derivation, squaring, averaging and lastly is the QRS
detection. The simulation results obtained is represented in a
Graphical User Interface (GUI) developed using MATLAB.
Abstract: This paper presents a controller design technique for
Synchronous Reluctance Motor to improve its dynamic performance
with fast response and high accuracy. The sliding mode control is the
most attractive and suitable method to use for this purpose, since it is
simple in design and for its insensitivity to parameter variations or
external disturbances. When this method implemented it yields fast
dynamic response without overshoot and a zero steady-state error.
The current loop control with decentralized sliding mode is presented
in this paper. The mathematical model for the synchronous machine,
the inverter and the controller is developed. The stability of the
sliding mode controller is analyzed. Simulation of synchronous
reluctance motor and the controller with PWM-inverter has been
curried out, using the SIMULINK software package of MATLAB.
Simulation results are presented to show the effectiveness of the
approach.
Abstract: This paper presents a new approach for the prob-ability density function estimation using the Support Vector Ma-chines (SVM) and the Expectation Maximization (EM) algorithms.In the proposed approach, an advanced algorithm for the SVM den-sity estimation which incorporates the Mean Field theory in the learning process is used. Instead of using ad-hoc values for the para-meters of the kernel function which is used by the SVM algorithm,the proposed approach uses the EM algorithm for an automatic optimization of the kernel. Experimental evaluation using simulated data set shows encouraging results.
Abstract: In this paper a novel high output impedance, low input impedance, wide bandwidth, very simple current mirror with input and output voltage requirements less than that of a simple current mirror is presented. These features are achieved with very simple structure avoiding extra large node impedances to ensure high bandwidth operation. The circuit's principle of operation is discussed and compared to simple and low voltage cascode (LVC) current mirrors. Such outstanding features of this current mirror as high output impedance ~384K, low input impedance~6.4, wide bandwidth~178MHz, low input voltage ~ 362mV, low output voltage ~ 38mV and low current transfer error ~4% (all at 50μA) makes it an outstanding choice for high performance applications. Simulation results in BSIM 0.35μm CMOS technology with HSPICE are given in comparison with simple, and LVC current mirrors to verify and validate the performance of the proposed current mirror.
Abstract: The proper design of RF pulses in magnetic resonance imaging (MRI) has a direct impact on the quality of acquired images, and is needed for many applications. Several techniques have been proposed to obtain the RF pulse envelope given the desired slice profile. Unfortunately, these techniques do not take into account the limitations of practical implementation such as limited amplitude resolution. Moreover, implementing constraints for special RF pulses on most techniques is not possible. In this work, we propose to develop an approach for designing optimal RF pulses under theoretically any constraints. The new technique will pose the RF pulse design problem as a combinatorial optimization problem and uses efficient techniques from this area such as genetic algorithms (GA) to solve this problem. In particular, an objective function will be proposed as the norm of the difference between the desired profile and the one obtained from solving the Bloch equations for the current RF pulse design values. The proposed approach will be verified using analytical solution based RF simulations and compared to previous methods such as Shinnar-Le Roux (SLR) method, and analysis, selected, and tested the options and parameters that control the Genetic Algorithm (GA) can significantly affect its performance to get the best improved results and compared to previous works in this field. The results show a significant improvement over conventional design techniques, select the best options and parameters for GA to get most improvement over the previous works, and suggest the practicality of using of the new technique for most important applications as slice selection for large flip angles, in the area of unconventional spatial encoding, and another clinical use.
Abstract: The dynamic model of a drill in drilling process was
proposed and investigated in this study. To assure a good drilling quality, the vibration variation on the drill tips during high speed
drilling is needed to be investigated. A pre-twisted beam is used to
simulate the drill. The moving Winkler-Type elastic foundation is used to characterize the tip boundary variation in drilling. Due to the
variation of the drill depth, a time dependent dynamic model for the drill is proposed. Results simulated from this proposed model indicate that an abrupt natural frequencies drop are experienced as the drill tip
tough the workpiece, and a severe vibration is induced. The effects of parameters, e.g. drilling speed, depth, drill size and thrust force on the
drill tip responses studied.