Abstract: This paper discusses aspects of re-design of loadshedding
schemes with respect to actual developments in the Kosovo
power system. Load-shedding is a type of emergency control that is
designed to ensure system stability by reducing power system load to
match the power generation supply. This paper presents a new
adaptive load-shedding scheme that provides emergency protection
against excess frequency decline, in cases when the Kosovo power
system might be disconnected from the regional transmission
network. The proposed load-shedding scheme uses the local
frequency rate information to adapt the load-shedding pattern to suit
the size and location of the occurring disturbance. The proposed
scheme is tested in a software simulation on a large scale PSS/E
model which represents nine power system areas of Southeast Europe
including the Kosovo power system.
Abstract: The householder RLS (HRLS) algorithm is an O(N2)
algorithm which recursively updates an arbitrary square-root of the
input data correlation matrix and naturally provides the LS weight
vector. A data dependent householder matrix is applied for such
an update. In this paper a recursive estimate of the eigenvalue
spread and misalignment of the algorithm is presented at a very low
computational cost. Misalignment is found to be highly sensitive to
the eigenvalue spread of input signals, output noise of the system and
exponential window. Simulation results show noticeable degradation
in the misalignment by increase in eigenvalue spread as well as
system-s output noise, while exponential window was kept constant.
Abstract: The comparisons of two typical fluidic thrust vectoring exhaust nozzles including two-dimensional(2-D) nozzle and axisymmetric nozzle on aerodynamic characteristics was presented by numerical simulation. The results show: the thrust vector angles increased with the increasing secondary flow but decreased with the nozzle pressure ratio (NPR) increasing. With the same secondary flow and NPR, the thrust vector angles of 2-D nozzle were higher than the axisymmetric nozzle-s. So with the lower NPR and more secondary weight flow, the much higher thrust vector angle was caused by 2-D fluidic nozzle. And with the higher NPR and less secondary weight flow, there was not much difference in angular dimension between two nozzles.
Abstract: Scaffolds play a key role in tissue engineering and can be produced in many different ways depending on the applications and the materials used. Most researchers used an experimental trialand- error approach into new biomaterials but computer simulation applied to tissue engineering can offer a more exhaustive approach to test and screen out biomaterials. This paper develops the model of scaffolds and Computational Fluid Dynamics that show the value of computer simulations in determining the influence of the geometrical scaffold parameter porosity, pore size and shape on the permeability of scaffolds, magnitude of velocity, drop pressure, shear stress distribution and level and the proper design of the geometry of the scaffold. This creates a need for more advanced studies that include aspects of dynamic conditions of a micro fluid passing through the scaffold were characterized for tissue engineering applications and differentiation of tissues within scaffolds.
Abstract: Zero inflated Strict Arcsine model is a newly developed model which is found to be appropriate in modeling overdispersed count data. In this study, maximum likelihood estimation method is used in estimating the parameters for zero inflated strict arcsine model. Bootstrapping is then employed to compute the confidence intervals for the estimated parameters.
Abstract: High redundancy and strong uncertainty are two main characteristics for underwater robotic manipulators with unlimited workspace and mobility, but they also make the motion planning and control difficult and complex. In order to setup the groundwork for the research on control schemes, the mathematical representation is built by using the Denavit-Hartenberg (D-H) method [9]&[12]; in addition to the geometry of the manipulator which was studied for establishing the direct and inverse kinematics. Then, the dynamic model is developed and used by employing the Lagrange theorem. Furthermore, derivation and computer simulation is accomplished using the MATLAB environment. The result obtained is compared with mechanical system dynamics analysis software, ADAMS. In addition, the creation of intelligent artificial skin using Interlink Force Sensing ResistorTM technology is presented as groundwork for future work
Abstract: Complex assemblies of interacting proteins carry out
most of the interesting jobs in a cell, such as metabolism, DNA
synthesis, mitosis and cell division. These physiological properties
play out as a subtle molecular dance, choreographed by underlying
regulatory networks that control the activities of cyclin-dependent
kinases (CDK). The network can be modeled by a set of nonlinear
differential equations and its behavior predicted by numerical
simulation. In this paper, an innovative approach has been proposed
that uses genetic algorithms to mine a set of behavior data output by
a biological system in order to determine the kinetic parameters of
the system. In our approach, the machine learning method is
integrated with the framework of existent biological information in a
wiring diagram so that its findings are expressed in a form of system
dynamic behavior. By numerical simulations it has been illustrated
that the model is consistent with experiments and successfully shown
that such application of genetic algorithms will highly improve the
performance of mathematical model of the cell division cycle to
simulate such a complicated bio-system.
Abstract: Selecting the routes and the assignment of link flow in a computer communication networks are extremely complex combinatorial optimization problems. Metaheuristics, such as genetic or simulated annealing algorithms, are widely applicable heuristic optimization strategies that have shown encouraging results for a large number of difficult combinatorial optimization problems. This paper considers the route selection and hence the flow assignment problem. A genetic algorithm and simulated annealing algorithm are used to solve this problem. A new hybrid algorithm combining the genetic with the simulated annealing algorithm is introduced. A modification of the genetic algorithm is also introduced. Computational experiments with sample networks are reported. The results show that the proposed modified genetic algorithm is efficient in finding good solutions of the flow assignment problem compared with other techniques.
Abstract: In this paper we propose a method which improves the efficiency of video coding. Our method combines an adaptive GOP (group of pictures) structure and the shot cut detection. We have analyzed different approaches for shot cut detection with aim to choose the most appropriate one. The next step is to situate N frames to the positions of detected cuts during the process of video encoding. Finally the efficiency of the proposed method is confirmed by simulations and the obtained results are compared with fixed GOP structures of sizes 4, 8, 12, 16, 32, 64, 128 and GOP structure with length of entire video. Proposed method achieved the gain in bit rate from 0.37% to 50.59%, while providing PSNR (Peak Signal-to-Noise Ratio) gain from 1.33% to 0.26% in comparison to simulated fixed GOP structures.
Abstract: This paper presents a new and efficient approach for capacitor placement in radial distribution systems that determine the optimal locations and size of capacitor with an objective of improving the voltage profile and reduction of power loss. The solution methodology has two parts: in part one the loss sensitivity factors are used to select the candidate locations for the capacitor placement and in part two a new algorithm that employs Plant growth Simulation Algorithm (PGSA) is used to estimate the optimal size of capacitors at the optimal buses determined in part one. The main advantage of the proposed method is that it does not require any external control parameters. The other advantage is that it handles the objective function and the constraints separately, avoiding the trouble to determine the barrier factors. The proposed method is applied to 9, 34, and 85-bus radial distribution systems. The solutions obtained by the proposed method are compared with other methods. The proposed method has outperformed the other methods in terms of the quality of solution.
Abstract: When an assignable cause(s) manifests itself to a multivariate process and the process shifts to an out-of-control condition, a root-cause analysis should be initiated by quality engineers to identify and eliminate the assignable cause(s) affected the process. A root-cause analysis in a multivariate process is more complex compared to a univariate process. In the case of a process involved several correlated variables an effective root-cause analysis can be only experienced when it is possible to identify the required knowledge including the out-of-control condition, the change point, and the variable(s) responsible to the out-of-control condition, all simultaneously. Although literature addresses different schemes to monitor multivariate processes, one can find few scientific reports focused on all the required knowledge. To the best of the author’s knowledge this is the first time that a multi task model based on artificial neural network (ANN) is reported to monitor all the required knowledge at the same time for a multivariate process with more than two correlated quality characteristics. The performance of the proposed scheme is evaluated numerically when different step shifts affect the mean vector. Average run length is used to investigate the performance of the proposed multi task model. The simulated results indicate the multi task scheme performs all the required knowledge effectively.
Abstract: In this paper, the energy performance of a selected
UHDE Ammonia plant is optimized by conducting heat integration through waste heat recovery and the synthesis of a heat exchange
network (HEN). Minimum hot and cold utility requirements were estimated through IChemE spreadsheet. Supporting simulation was
carried out using HYSYS software. The results showed that there is
no need for heating utility while the required cold utility was found to
be around 268,714 kW. Hence a threshold pinch case was faced. Then, the hot and cold streams were matched appropriately. Also,
waste heat recovered resulted with savings in HP and LP steams of
approximately 51.0% and 99.6%, respectively. An economic analysis
on proposed HEN showed very attractive overall payback period not
exceeding 3 years. In general, a net saving approaching 35% was
achieved in implementing heat optimization of current studied UHDE Ammonia process.
Abstract: The Spalart and Allmaras turbulence model has been
implemented in a numerical code to study the compressible turbulent
flows, which the system of governing equations is solved with a
finite volume approach using a structured grid. The AUSM+ scheme
is used to calculate the inviscid fluxes. Different benchmark
problems have been computed to validate the implementation and
numerical results are shown. A special Attention is paid to wall jet
applications. In this study, the jet is submitted to various wall
boundary conditions (adiabatic or uniform heat flux) in forced
convection regime and both two-dimensional and axisymmetric wall
jets are considered. The comparison between the numerical results
and experimental data has given the validity of this turbulence model
to study the turbulent wall jets especially in engineering applications.
Abstract: Today, Hydroforming technology provides an
attractive alternative to conventional matched die forming, especially
for cost-sensitive, lower volume production, and for parts with
irregular contours. In this study the critical fluid pressures which lead
to rupture in the workpiece has been investigated by theoretical and
finite element methods. The axisymmetric analysis was developed to
investigate the tearing phenomenon in cylindrical Hydroforming
Deep Drawing (HDD). By use of obtained equations the effect of
anisotropy, drawing ratio, sheet thickness and strain hardening
exponent on tearing diagram were investigated.
Abstract: Low-density parity-check (LDPC) codes have been shown to deliver capacity approaching performance; however, problematic graphical structures (e.g. trapping sets) in the Tanner graph of some LDPC codes can cause high error floors in bit-error-ratio (BER) performance under conventional sum-product algorithm (SPA). This paper presents a serial concatenation scheme to avoid the trapping sets and to lower the error floors of LDPC code. The outer code in the proposed concatenation is the LDPC, and the inner code is a high rate array code. This approach applies an interactive hybrid process between the BCJR decoding for the array code and the SPA for the LDPC code together with bit-pinning and bit-flipping techniques. Margulis code of size (2640, 1320) has been used for the simulation and it has been shown that the proposed concatenation and decoding scheme can considerably improve the error floor performance with minimal rate loss.
Abstract: In this paper, propagation of cos-Gaussian beam in strongly nonlocal nonlinear media has been stimulated by using paraxial group transformation. At first, cos-Gaussian beam, nonlocal nonlinear media, critical power, transfer matrix, and paraxial group transformation are introduced. Then, the propagation of the cos-Gaussian beam in strongly nonlocal nonlinear media is simulated. Results show that beam propagation has periodic structure during self-focusing effect in this case. However, this simple method can be used for investigation of propagation of kinds of beams in ABCD optical media.
Abstract: The seismic response of steel shear wall system considering nonlinearity effects using finite element method is investigated in this paper. The non-linear finite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of finite element code. A numerical model based on the finite element method for the seismic analysis of shear wall is presented with developing of finite element code in this research. To develop the finite element code, the standard Galerkin weighted residual formulation is used. Two-dimensional plane stress model and total Lagrangian formulation was carried out to present the shear wall response and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The presented model in this paper can be developed for analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: The paper shows some ability to manage two-phase
flows arising from the use of unsteady effects. In one case, we
consider the condition of fragmentation of the interface between the
two components leads to the intensification of mixing. The problem
is solved when the temporal and linear scale are small for the
appearance of the developed mixing layer. Showing that exist such
conditions for unsteady flow velocity at the surface of the channel,
which will lead to the creation and fragmentation of vortices at Re
numbers of order unity. Also showing that the Re is not a criterion of
similarity for this type of flows, but we can introduce a criterion that
depends on both the Re, and the frequency splitting of the vortices. It
turned out that feature of this situation is that streamlines behave
stable, and if we analyze the behavior of the interface between the
components it satisfies all the properties of unstable flows. The other
problem we consider the behavior of solid impurities in the extensive
system of channels. Simulated unsteady periodic flow modeled
breaths. Consider the behavior of the particles along the trajectories.
It is shown that, depending on the mass and diameter of the particles,
they can be collected in a caustic on the channel walls, stop in a
certain place or fly back. Of interest is the distribution of particle
velocity in frequency. It turned out that by choosing a behavior of the
velocity field of the carrier gas can affect the trajectory of individual
particles including force them to fly back.
Abstract: The performance of an image filtering system depends
on its ability to detect the presence of noisy pixels in the image. Most
of the impulse detection schemes assume the presence of salt and
pepper noise in the images and do not work satisfactorily in case of
uniformly distributed impulse noise. In this paper, a new algorithm is
presented to improve the performance of switching median filter in
detection of uniformly distributed impulse noise. The performance of
the proposed scheme is demonstrated by the results obtained from
computer simulations on various images.
Abstract: When binary decision diagrams are formed from
uniformly distributed Monte Carlo data for a large number of
variables, the complexity of the decision diagrams exhibits a
predictable relationship to the number of variables and minterms. In
the present work, a neural network model has been used to analyze the
pattern of shortest path length for larger number of Monte Carlo data
points. The neural model shows a strong descriptive power for the
ISCAS benchmark data with an RMS error of 0.102 for the shortest
path length complexity. Therefore, the model can be considered as a
method of predicting path length complexities; this is expected to lead
to minimum time complexity of very large-scale integrated circuitries
and related computer-aided design tools that use binary decision
diagrams.