Abstract: In this paper, the application of sliding-mode control to a permanent-magnet synchronous motor (PMSM) is presented. The control design is based on a generic mathematical model of the motor. Some dynamics of the motor and of the power amplification stage remain unmodelled. This model uncertainty is estimated in realtime. The estimation is based on the differentiation of measured signals using the ideas of robust exact differentiator (RED). The control law is implemented on an industrial servo drive. Simulations and experimental results are presented and compared to the same control strategy without uncertainty estimation. It turns out that the proposed concept is superior to the same control strategy without uncertainty estimation especially in the case of non-smooth reference signals.
Abstract: This study presents a novel means of designing a simple and effective torque controller for Permanent Magnet Synchronous Motor (PMSM). The overall stability of the system is shown using Lyapunov technique. The Lyapunov functions used contain a term penalizing the integral of the tracking error, enhancing the stability. The tracking error is shown to be globally uniformly bounded. Simulation results are presented to show the effectiveness of the approach.
Abstract: This paper presents two different sequential switching hybrid-modulation strategies and implemented for cascaded multilevel inverters. Hybrid modulation strategies represent the combinations of Fundamental-frequency pulse width modulation (FFPWM) and Multilevel sinusoidal-modulation (MSPWM) strategies, and are designed for performance of the well-known Alternative Phase opposition disposition (APOD), Phase shifted carrier (PSC). The main characteristics of these modulations are the reduction of switching losses with good harmonic performance, balanced power loss dissipation among the devices with in a cell, and among the series-connected cells. The feasibility of these modulations is verified through spectral analysis, power loss analysis and simulation.
Abstract: Today, canines are still used effectively in acceleration detection situation. However, this method is becoming impractical in modern age and a new automated replacement to the canine is required. This paper reports the design of an innovative accelerant detector. Designing an accelerant detector is a long process as is any design process; therefore, a solution to the need for a mobile, effective accelerant detector is hereby presented. The device is simple and efficient to ensure that any accelerant detection can be conducted quickly and easily. The design utilizes Ultra Violet (UV) light to detect the accelerant. When the UV light shines on an accelerant, the hydrocarbons in the accelerant emit florescence. The advantages of using the UV light to detect accelerant are also outlined in this paper. The mobility of the device is achieved by using a Direct Current (DC) motor to run tank tracks. Tank tracks were chosen as to ensure that the device will be mobile in the rough terrain of a fire site. The materials selected for the various parts are also presented. A Solid Works Simulation was also conducted on the stresses in the shafts and the results are presented. This design is an innovative solution which offers a user friendly interface. The design is also environmentally friendly, ecologically sound and safe to use.
Abstract: In a chirp spread spectrum (CSS) system, the overlap
technique is used for increasing bit rate. More overlaps can offer
higher data throughput; however, they may cause more intersymbol
interference (ISI) at the same time, resulting in serious bit error
rate (BER) performance degradation. In this paper, we perform the
BER analysis and derive a closed form BER expression for the
overlap-based CSS system. The derived BER expression includes
the number of overlaps as a parameter, and thus, would be very
useful in determining the number of overlaps for a specified BER.
The numerical results demonstrate that the BER derived in a closed
form closely agrees with the simulated BER.
Abstract: The cellular network is one of the emerging areas of
communication, in which the mobile nodes act as member for one
base station. The cluster based communication is now an emerging
area of wireless cellular multimedia networks. The cluster renders
fast communication and also a convenient way to work with
connectivity. In our scheme we have proposed an optimization
technique for the fuzzy cluster nodes, by categorizing the group
members into three categories like long refreshable member, medium
refreshable member and short refreshable member. By considering
long refreshable nodes as static nodes, we compute the new
membership values for the other nodes in the cluster. We compare
their previous and present membership value with the threshold value
to categorize them into three different members. By which, we
optimize the nodes in the fuzzy clusters. The simulation results show
that there is reduction in the cluster computational time and
iterational time after optimization.
Abstract: With the demand of mobility by users, wireless
technologies have become the hotspot developing arena. Internet
Engineering Task Force (IETF) working group has developed Mobile
IP to support node mobility. The concept of node mobility indicates
that in spite of the movement of the node, it is still connected to the
internet and all the data transactions are preserved. It provides
location-independent access to Internet. After the incorporation of
host mobility, network mobility has undergone intense research.
There are several intricacies faced in the real world implementation
of network mobility significantly the problem of nested networks and
their consequences. This article is concerned regarding a problem of
nested network called pinball route problem and proposes a solution
to eliminate the above problem. The proposed mechanism is
implemented using NS2 simulation tool and it is found that the
proposed mechanism efficiently reduces the overload caused by the
pinball route problem.
Abstract: This research paper designs a unique motion planner
of multiple platoons of nonholonomic car-like robots as a feasible
solution to the lane changing/merging maneuvers. The decentralized
planner with a leaderless approach and a path-guidance principle
derived from the Lyapunov-based control scheme generates collision
free avoidance and safe merging maneuvers from multiple lanes to a
single lane by deploying a split/merge strategy. The fixed obstacles
are the markings and boundaries of the road lanes, while the moving
obstacles are the robots themselves. Real and virtual road lane
markings and the boundaries of road lanes are incorporated into a
workspace to achieve the desired formation and configuration of the
robots. Convergence of the robots to goal configurations and the
repulsion of the robots from specified obstacles are achieved by
suitable attractive and repulsive potential field functions,
respectively. The results can be viewed as a significant contribution
to the avoidance algorithm of the intelligent vehicle systems (IVS).
Computer simulations highlight the effectiveness of the split/merge
strategy and the acceleration-based controllers.
Abstract: Over recent years, the number of building integrated photovoltaic (BIPV) installations for home systems have been increasing in Malaysia. The paper concerns an analysis - as part of current Research and Development (R&D) efforts - to integrate photovoltaics as an architectural feature of a detached house in the new satellite township of Putrajaya, Malaysia. The analysis was undertaken using calculation and simulation tools to optimize performance of BIPV home system. In this study, a the simulation analysis was undertaken for selected bungalow units based on a long term recorded weather data for city of Kuala Lumpur. The simulation and calculation was done with consideration of a PV panels' tilt and direction, shading effect and economical considerations. A simulation of the performance of a grid connected BIPV house in Kuala Lumpur was undertaken. This case study uses a 60 PV modules with power output of 2.7 kW giving an average of PV electricity output is 255 kWh/month..
Abstract: An accurate procedure to determine free vibrations of
beams and plates is presented.
The natural frequencies are exact solutions of governing vibration
equations witch load to a nonlinear homogeny system.
The bilinear and linear structures considered simulate a bridge.
The dynamic behavior of this one is analyzed by using the theory of
the orthotropic plate simply supported on two sides and free on the
two others. The plate can be excited by a convoy of constant or
harmonic loads. The determination of the dynamic response of the
structures considered requires knowledge of the free frequencies and
the shape modes of vibrations. Our work is in this context. Indeed,
we are interested to develop a self-consistent calculation of the Eigen
frequencies.
The formulation is based on the determination of the solution of
the differential equations of vibrations. The boundary conditions
corresponding to the shape modes permit to lead to a homogeneous
system. Determination of the noncommonplace solutions of this
system led to a nonlinear problem in Eigen frequencies.
We thus, develop a computer code for the determination of the
eigenvalues. It is based on a method of bisection with interpolation
whose precision reaches 10 -12. Moreover, to determine the
corresponding modes, the calculation algorithm that we develop uses
the method of Gauss with a partial optimization of the "pivots"
combined with an inverse power procedure. The Eigen frequencies
of a plate simply supported along two opposite sides while
considering the two other free sides are thus analyzed. The results
could be generalized with the case of a beam by regarding it as a
plate with low width.
We give, in this paper, some examples of treated cases. The
comparison with results presented in the literature is completely
satisfactory.
Abstract: The RANS method with Saffman-s turbulence model
was employed to solve the time-dependent turbulent Navier-Stokes
and energy equations for oscillating pipe flows. The method of
partial sums of the Fourier series is used to analyze the harmonic
velocity and temperature results. The complete structures of the
oscillating pipe flows and the averaged Nusselt numbers on the tube
wall are provided by numerical simulation over wide ranges of ReA
and ReR. Present numerical code is validated by comparing the
laminar flow results to analytic solutions and turbulence flow results
to published experimental data at lower and higher Reynolds
numbers respectively. The effects of ReA and ReR on the velocity,
temperature and Nusselt number distributions have been di scussed.
The enhancement of the heat transfer due to oscillating flows has
also been presented. By the way of analyzing the overall Nusselt
number over wide ranges of the Reynolds number Re and Keulegan-
Carpenter number KC, the optimal ratio of the tube diameter over
the oscillation amplitude is obtained based on the existence of a
nearly constant optimal KC number. The potential application of the
present results in sea water cooling has also been discussed.
Abstract: Spray chilling using air-mist nozzles has received
much attention in the food processing industry because of the
benefits it has shown over forced air convection. These benefits
include an increase in the heat transfer coefficient and a reduction in
the water loss by the product during cooling. However, few studies
have simulated the heat transfer and aerodynamics phenomena of the
air-mist chilling process for optimal operating conditions. The study
provides insight into the optimal conditions for spray impaction, heat
transfer efficiency and control of surface flooding. A computational
fluid dynamics model using a two-phase flow composed of water
droplets injected with air is developed to simulate the air-mist
chilling of food products. The model takes into consideration
droplet-to-surface interaction, water-film accumulation and surface
runoff. The results of this study lead to a better understanding of the
heat transfer enhancement, water conservation, and to a clear
direction for the optimal design of air-mist chilling systems that can
be used in commercial applications in the food and meat processing
industries.
Abstract: Nowadays there are many methods for representing
knowledge such as semantic network, neural network, and conceptual
graphs. Nonetheless, these methods are not sufficiently efficient
when applied to perform and deduce on knowledge domains about
supporting in general education such as algebra, analysis or plane
geometry. This leads to the introduction of computational network
which is a useful tool for representation knowledge base, especially
for computational knowledge, especially knowledge domain about
general education. However, when dealing with a practical problem,
we often do not immediately find a new solution, but we search
related problems which have been solved before and then proposing
an appropriate solution for the problem. Besides that, when finding
related problems, we have to determine whether the result of them
can be used to solve the practical problem or not. In this paper, the
extension model of computational network has been presented. In this
model, Sample Problems, which are related problems, will be used
like the experience of human about practical problem, simulate the
way of human thinking, and give the good solution for the practical
problem faster and more effectively. This extension model is applied
to construct an automatic system for solving algebraic problems in
middle school.
Abstract: The compatibility of optical resonators with microfluidic systems may be relevant for chemical and biological applications. Here, a fluorescent-core microcavity (FCM) is investigated as a refractometric sensor for heavy oils. A high-index film of silicon quantum dots (QDs) was formed inside the capillary, supporting cylindrical fluorescence whispering gallery modes (WGMs). A set of standard refractive index oils was injected into a capillary, causing a shift of the WGM resonances toward longer wavelengths. A maximum sensitivity of 240 nm/RIU (refractive index unit) was found for a nominal oil index of 1.74. As well, a sensitivity of 22 nm/RIU was obtained for a lower index of 1.48, more typical of fuel hydrocarbons. Furthermore, the observed spectra and sensitivities were compared to theoretical predictions and reproduced via FDTD simulations, showing in general an excellent agreement. This work demonstrates the potential use of FCMs for oil sensing applications and the more generally for detecting liquid solutions with a high refractive index or high viscosity.
Abstract: The flow field over a flat roof model building has been numerically investigated in order to determine threedimensional CFD guidelines for the calculation of the turbulent flow over a structure immersed in an atmospheric boundary layer. To this purpose, a complete validation campaign has been performed through a systematic comparison of numerical simulations with wind tunnel experimental data. Wind tunnel measurements and numerical predictions have been compared for five different vertical positions, respectively from the upstream leading edge to the downstream bottom edge of the analyzed model. Flow field characteristics in the neighborhood of the building model have been numerically investigated, allowing a quantification of the capabilities of the CFD code to predict the flow separation and the extension of the recirculation regions. The proposed calculations have allowed the development of a preliminary procedure to be used as guidance in selecting the appropriate grid configuration and corresponding turbulence model for the prediction of the flow field over a three-dimensional roof architecture dominated by flow separation.
Abstract: Conceptualization strengthens intelligent systems in generalization skill, effective knowledge representation, real-time inference, and managing uncertain and indefinite situations in addition to facilitating knowledge communication for learning agents situated in real world. Concept learning introduces a way of abstraction by which the continuous state is formed as entities called concepts which are connected to the action space and thus, they illustrate somehow the complex action space. Of computational concept learning approaches, action-based conceptualization is favored because of its simplicity and mirror neuron foundations in neuroscience. In this paper, a new biologically inspired concept learning approach based on the probabilistic framework is proposed. This approach exploits and extends the mirror neuron-s role in conceptualization for a reinforcement learning agent in nondeterministic environments. In the proposed method, instead of building a huge numerical knowledge, the concepts are learnt gradually from rewards through interaction with the environment. Moreover the probabilistic formation of the concepts is employed to deal with uncertain and dynamic nature of real problems in addition to the ability of generalization. These characteristics as a whole distinguish the proposed learning algorithm from both a pure classification algorithm and typical reinforcement learning. Simulation results show advantages of the proposed framework in terms of convergence speed as well as generalization and asymptotic behavior because of utilizing both success and failures attempts through received rewards. Experimental results, on the other hand, show the applicability and effectiveness of the proposed method in continuous and noisy environments for a real robotic task such as maze as well as the benefits of implementing an incremental learning scenario in artificial agents.
Abstract: A multi-rate discrete-time model, whose response
agrees exactly with that of a continuous-time original at all sampling
instants for any sampling periods, is developed for a linear system,
which is assumed to have multiple real eigenvalues. The sampling
rates can be chosen arbitrarily and individually, so that their ratios
can even be irrational. The state space model is obtained as a
combination of a linear diagonal state equation and a nonlinear output
equation. Unlike the usual lifted model, the order of the proposed
model is the same as the number of sampling rates, which is less than
or equal to the order of the original continuous-time system. The
method is based on a nonlinear variable transformation, which can be
considered as a generalization of linear similarity transformation,
which cannot be applied to systems with multiple eigenvalues in
general. An example and its simulation result show that the proposed
multi-rate model gives exact responses at all sampling instants.
Abstract: The winding hot-spot temperature is one of the most
critical parameters that affect the useful life of the power
transformers. The winding hot-spot temperature can be calculated as
function of the top-oil temperature that can estimated by using the
ambient temperature and transformer loading measured data. This
paper proposes the estimation of the top-oil temperature by using a
method based on Least Squares Support Vector Machines approach.
The estimated top-oil temperature is compared with measured data of
a power transformer in operation. The results are also compared with
methods based on the IEEE Standard C57.91-1995/2000 and
Artificial Neural Networks. It is shown that the Least Squares
Support Vector Machines approach presents better performance than
the methods based in the IEEE Standard C57.91-1995/2000 and
artificial neural networks.
Abstract: This paper discusses the investigation of a wearable
textile monopole antenna on specific absorption rate (SAR) for bodycentric
wireless communication applications at 2.45 GHz. The
antenna is characterized on a realistic 8 x 8 x 8 mm3 resolution
truncated Hugo body model in CST Microwave Studio software. The
result exhibited that the simulated SAR values were reduced
significantly by 83.5% as the position of textile monopole was
varying between 0 mm and 15 mm away from the human upper arm.
A power absorption reduction of 52.2% was also noticed as the
distance of textile monopole increased.
Abstract: In this paper, we study the formation control problem
for car-like mobile robots. A team of nonholonomic mobile robots navigate in a terrain with obstacles, while maintaining a desired
formation, using a leader-following strategy. A set of artificial potential field functions is proposed using the direct Lyapunov
method for the avoidance of obstacles and attraction to their designated targets. The effectiveness of the proposed control laws to verify the feasibility of the model is demonstrated through computer simulations