Abstract: Unlike the best effort service provided by the internet
today, next-generation wireless networks will support real-time
applications. This paper proposes an adaptive early packet discard
(AEPD) policy to improve the performance of the real time TCP
traffic over ATM networks and avoid the fragmentation problem.
Three main aspects are incorporated in the proposed policy. First,
providing quality-of-service (QoS) guaranteed for real-time
applications by implementing a priority scheduling. Second,
resolving the partially corrupted packets problem by differentiating
the buffered cells of one packet from another. Third, adapting a
threshold dynamically using Fuzzy logic based on the traffic
behavior to maintain a high throughput under a variety of load
conditions. The simulation is run for two priority classes of the input
traffic: real time and non-real time classes. Simulation results show
that the proposed AEPD policy improves throughput and fairness
over that using static threshold under the same traffic conditions.
Abstract: The ability to detect and classify the type of fault
plays a great role in the protection of power system. This procedure
is required to be precise with no time consumption. In this paper
detection of fault type has been implemented using wavelet analysis
together with wavelet entropy principle. The simulation of power
system is carried out using PSCAD/EMTDC. Different types of
faults were studied obtaining various current waveforms. These
current waveforms were decomposed using wavelet analysis into
different approximation and details. The wavelet entropy of such
decompositions is analyzed reaching a successful methodology for
fault classification. The suggested approach is tested using different
fault types and proven successful identification for the type of fault.
Abstract: The paper investigates parallel channel instabilities of
natural circulation boiling water reactor. A thermal-hydraulic model
is developed to simulate two-phase flow behavior in the natural circulation boiling water reactor (NCBWR) with the incorporation of
ex-core components and recirculation loop such as steam separator, down-comer, lower-horizontal section and upper-horizontal section
and then, numerical analysis is carried out for parallel channel
instabilities of the reactor undergoing both in-phase and out-of-phase
modes of oscillations. To analyze the relative effect on stability of the reactor due to inclusion of various ex-core components and
recirculation loop, marginal stable point is obtained at a particular inlet enthalpy of the reactor core without the inclusion of ex-core
components and recirculation loop and then with the inclusion of the
same. Numerical simulations are also conducted to determine the
relative dominance between two modes of oscillations i.e. in-phase and out-of-phase. Simulations are also carried out when the channels
are subjected to asymmetric power distribution keeping the inlet enthalpy same.
Abstract: Hydrogen sulfide (H2S) is a very toxic gas that is produced in very large quantities in the oil and gas industry. It cannot be flared to the atmosphere and Claus process based gas plants are used to recover the sulfur and convert the hydrogen to water. In this paper, we present optical characterization of an atmospheric pressure microwave plasma torch for H2S dissociation into hydrogen and sulfur. The torch is operated at 2.45 GHz with power up to 2 kW. Three different gases can simultaneously be injected in the plasma torch. Visual imaging and optical emission spectroscopy are used to characterize the plasma for varying gas flow rates and microwave power. The plasma length, emission spectra and temperature are presented. The obtained experimental results validate our earlier published simulation results of plasma torch.
Abstract: In this paper we propose a robust adaptive fuzzy
controller for a class of nonlinear system with unknown dynamic.
The method is based on type-2 fuzzy logic system to approximate
unknown non-linear function. The design of the on-line adaptive
scheme of the proposed controller is based on Lyapunov technique.
Simulation results are given to illustrate the effectiveness of the
proposed approach.
Abstract: In this paper, we introduce a robust state feedback controller design using Linear Matrix Inequalities (LMIs) and guaranteed cost approach for Takagi-Sugeno fuzzy systems. The purpose on this work is to establish a systematic method to design controllers for a class of uncertain linear and non linear systems. Our approach utilizes a certain type of fuzzy systems that are based on Takagi-Sugeno (T-S) fuzzy models to approximate nonlinear systems. We use a robust control methodology to design controllers. This method not only guarantees stability, but also minimizes an upper bound on a linear quadratic performance measure. A simulation example is presented to show the effectiveness of this method.
Abstract: Cast metal inlays can be used on molars requiring a
class II restoration instead amalgam and offer a durable alternative.
Because it is known that class II inlays may increase the
susceptibility to fracture, it is important to ensure optimal
performance in selection of the adequate preparation design to reduce
stresses in teeth structures and also in the restorations. The aim of the
study was to investigate the influence of preparation design on stress
distribution in molars with different class II preparations and in cast
metal inlays. The first step of the study was to achieve 3D models in
order to analyze teeth and cast metal class II inlays. The geometry of
the intact tooth was obtained by 3D scanning using a manufactured
device. With a NURBS modeling program the preparations and the
appropriately inlays were designed. 3D models of first upper molars
of the same shape and size were created. Inlay cavities designs were
created using literature data. The geometrical model was exported
and the mesh structure of the solid 3D model was created for
structural simulations. Stresses were located around the occlusal
contact areas. For the studied cases, the stress values were not
significant influenced by the taper of the preparation. it was
demonstrated stresses are higher in the cast metal restorations and
therefore the strength of the teeth is not affected.
Abstract: Mathematical models can be used to describe the
dynamics of the spread of infectious disease between susceptibles
and infectious populations. Dengue fever is a re-emerging disease in
the tropical and subtropical regions of the world. Its incidence has
increased fourfold since 1970 and outbreaks are now reported quite
frequently from many parts of the world. In dengue endemic regions,
more cases of dengue infection in pregnancy and infancy are being
found due to the increasing incidence. It has been reported that
dengue infection was vertically transmitted to the infants. Primary
dengue infection is associated with mild to high fever, headache,
muscle pain and skin rash. Immune response includes IgM antibodies
produced by the 5th day of symptoms and persist for 30-60 days. IgG
antibodies appear on the 14th day and persist for life. Secondary
infections often result in high fever and in many cases with
hemorrhagic events and circulatory failure. In the present paper, a
mathematical model is proposed to simulate the succession of dengue
disease transmission in pregnancy and infancy. Stability analysis of
the equilibrium points is carried out and a simulation is given for the
different sets of parameter. Moreover, the bifurcation diagrams of our
model are discussed. The controlling of this disease in infant cases is
introduced in the term of the threshold condition.
Abstract: In this article, a simulation method called the Homotopy Perturbation Method (HPM) is employed in the steady flow of a Walter's B' fluid in a vertical channel with porous wall. We employed Homotopy Perturbation Method to derive solution of a nonlinear form of equation obtained from exerting similarity transforming to the ordinary differential equation gained from continuity and momentum equations of this kind of flow. The results obtained from the Homotopy Perturbation Method are then compared with those from the Runge–Kutta method in order to verify the accuracy of the proposed method. The results show that the Homotopy Perturbation Method can achieve good results in predicting the solution of such problems. Ultimately we use this solution to obtain the other terms of velocities and physical discussion about it.
Abstract: There are various solutions for improving existing overhead line systems with the general purpose of increasing their limited capacity. The capacity reserve of the existing overhead lines is an important problem that must be considered from different aspects. The paper contains a comparative analysis of the mechanical and thermal limitations of an existing overhead line based on certain calculation conditions characterizing the examined variants. The methodology of the proposed estimation of the permissible conductor temperature and maximum load current is described in detail. The transmission line model consists of specific information of an existing overhead line of the Latvian power network. The main purpose of the simulation tasks is to find an additional capacity reserve by using accurate mathematical models. The results of the obtained data are presented.
Abstract: This paper evaluates the performance of a novel
algorithm for tracking of a mobile node, interms of execution time
and root mean square error (RMSE). Particle Filter algorithm is used
to track the mobile node, however a new technique in particle filter
algorithm is also proposed to reduce the execution time. The
stationary points were calculated through trilateration and finally by
averaging the number of points collected for a specific time, whereas
tracking is done through trilateration as well as particle filter
algorithm. Wi-Fi signal is used to get initial guess of the position of
mobile node in x-y coordinates system. Commercially available
software “Wireless Mon" was used to read the WiFi signal strength
from the WiFi card. Visual Cµ version 6 was used to interact with
this software to read only the required data from the log-file
generated by “Wireless Mon" software. Results are evaluated through
mathematical modeling and MATLAB simulation.
Abstract: This paper presents the design, development and characterization of contractile water jet thruster (CWJT) for mini underwater robot. Instead of electric motor, this CWJT utilizes the Ionic Polymer Metal Composite (IPMC) as the actuator to generate the water jet. The main focus of this paper is to analyze the conceptual design of the proposed CWJT which would determine the thrust force value, jet flow behavior and actuator’s stress. Those thrust force and jet flow studies were carried out using Matlab/Simscape simulation software. The actuator stress had been analyzed using COSMOS simulation software. The results showed that there was no significant change for jet velocity at variable cross sectional nozzle area. However, a significant change was detected for jet velocity at different nozzle cross sectional area ratio which was up to 37%. The generated thrust force has proportional relation to the nozzle cross sectional area.
Abstract: Carriers scattering in the inversion channel of n-
MOSFET dominates the drain current. This paper presents an effective
electron mobility model for the pocket implanted nano scale
n-MOSFET. The model is developed by using two linear pocket
profiles at the source and drain edges. The channel is divided into
three regions at source, drain and central part of the channel region.
The total number of inversion layer charges is found for these three
regions by numerical integration from source to drain ends and the
number of depletion layer charges is found by using the effective
doping concentration including pocket doping effects. These two
charges are then used to find the effective normal electric field,
which is used to find the effective mobility model incorporating the
three scattering mechanisms, such as, Coulomb, phonon and surface
roughness scatterings as well as the ballistic phenomena for the
pocket implanted nano-scale n-MOSFET. The simulation results show
that the derived mobility model produces the same results as found
in the literatures.
Abstract: This work concerns the measurements of a Bulk
Acoustic Waves (BAW) emission filter S parameters and compare
with prototypes simulated types. Thanks to HP-ADS, a co-simulation
of filters- characteristics in a digital radio-communication chain is
performed. Four cases of modulation schemes are studied in order to
illustrate the impact of the spectral occupation of the modulated
signal. Results of simulations and co-simulation are given in terms of
Error Vector Measurements to be useful for a general sensibility
analysis of 4th/3rd Generation (G.) emitters (wideband QAM and
OFDM signals)
Abstract: The production and consumption of natural gas is on
the rise throughout the world as a result of its wide availability, ease
of transportation, use and clean-burning characteristics. The chief use
of ethane is in the chemical industry in the production of Ethene
(ethylene) by steam cracking. In this simulation, obtained ethane
recovery percent based on Gas sub-cooled process (GSP) is 99.9 by
mole that is included 32.1% by using de-methanizer column and
67.8% by de-ethanizer tower. The outstanding feature of this process
is the novel split-vapor concept that employs to generate reflux for
de-methanizer column. Remain amount of ethane in export gas cause
rise in gross heating value up to 36.66 MJ/Nm3 in order to use in
industrial and household consumptions.
Abstract: A pilot plant for continuous flow microwave-assisted
chemical reaction combined with microreactors was developed and
water heating tests were conducted for evaluation of the developed
plant. We developed a microwave apparatus having a single
microwave generator that can heat reaction solutions in four reaction
fields simultaneously in order to increase throughput. We also
designed a four-branch waveguide using electromagnetic simulation,
and found that the transmission efficiency at 99%. Finally, we
developed the pilot plant using the developed microwave apparatus
and conducted water heating tests. The temperatures in the respective
reaction fields were controlled within ±1.1 K at 353.2 K. Moreover,
the energy absorption rates by the water were about 90% in the
respective reaction fields, whereas the energy absorption rate was
about 40% when 100 cm3 of water was heated by a commercially
available multimode microwave chemical reactor.
Abstract: A bird strike can cause damage to stationary and
rotating aircraft engine parts, especially the engine fan. This paper
presents a bird strike simulated by blocking four stator blade
passages. It includes the numerical results of the unsteady lowfrequency
aerodynamic forces and the aeroelastic behaviour caused
by a non-symmetric upstream flow affecting the first two rotor blade
stages in the axial-compressor of a jet engine. The obtained results
show that disturbances in the engine inlet strongly influence the level
of unsteady forces acting on the rotor blades. With a partially
blocked inlet the whole spectrum of low-frequency harmonics is
observed. Such harmonics can lead to rotor blade damage. The lowfrequency
amplitudes are higher in the first stage rotor blades than in
the second stage. In both rotor blades stages flutter appeared as a
result of bird strike.
Abstract: A novel low-cost flight simulator with the development
goals cost effectiveness and high performance has been realized for
meeting the huge pilot training needs of airlines. The simulator
consists of an aircraft dynamics model, a sophisticated designed
low-profile electrical driven motion system with a subsided cabin, a
mixed reality based semi-virtual cockpit system, a control loading
system and some other subsystems. It shows its advantages over
traditional flight simulator by its features achieved with open
architecture, software solutions and low-cost hardware.
Abstract: This paper proposes an efficient finite precision block floating point (BFP) treatment to the fixed coefficient finite impulse response (FIR) digital filter. The treatment includes effective implementation of all the three forms of the conventional FIR filters, namely, direct form, cascaded and par- allel, and a roundoff error analysis of them in the BFP format. An effective block formatting algorithm together with an adaptive scaling factor is pro- posed to make the realizations more simple from hardware view point. To this end, a generic relation between the tap weight vector length and the input block length is deduced. The implementation scheme also emphasises on a simple block exponent update technique to prevent overflow even during the block to block transition phase. The roundoff noise is also investigated along the analogous lines, taking into consideration these implementational issues. The simulation results show that the BFP roundoff errors depend on the sig- nal level almost in the same way as floating point roundoff noise, resulting in approximately constant signal to noise ratio over a relatively large dynamic range.
Abstract: Robotic system is an important area in artificial intelligence that aims at developing the performance techniques of the robot and making it more efficient and more effective in choosing its correct behavior. In this paper the distributed learning classifier system is used for designing a simulated control system for robot to perform complex behaviors. A set of enhanced approaches that support default hierarchies formation is suggested and compared with each other in order to make the simulated robot more effective in mapping the input to the correct output behavior.