Abstract: The main objective of this paper is to investigate the
enhancement of power system stability via coordinated tuning of
Power System Stabilizers (PSSs) in a multi-machine power system.
The design problem of the proposed controllers is formulated as an
optimization problem. Chaotic catfish particle swarm optimization
(C-Catfish PSO) algorithm is used to minimize the ITAE objective
function. The proposed algorithm is evaluated on a two-area, 4-
machines system. The robustness of the proposed algorithm is
verified on this system under different operating conditions and
applying a three-phase fault. The nonlinear time-domain simulation
results and some performance indices show the effectiveness of the
proposed controller in damping power system oscillations and this
novel optimization algorithm is compared with particle swarm
optimization (PSO).
Abstract: This research was conducted in the Lower Ping River
Basin downstream of the Bhumibol Dam and the Lower Wang River
Basin in Tak Province, Thailand. Most of the tributary streams of the
Ping can be considered as ungauged catchments. There are 10-
pumping station installation at both river banks of the Ping in Tak
Province. Recently, most of them could not fully operate due to the
water amount in the river below the level that would be pumping,
even though included water from the natural river and released flow
from the Bhumibol Dam. The aim of this research was to increase the
performance of those pumping stations using weir projects in the
Ping. Therefore, the river analysis system model (HEC-RAS) was
applied to study the hydraulic behavior of water surface profiles in
the Ping River with both cases of existing conditions and proposed
weirs during the violent flood in 2011 and severe drought in 2013.
Moreover, the hydrologic modeling system (HMS) was applied to
simulate lateral streamflow hydrograph from ungauged catchments of
the Ping. The results of HEC-RAS model calibration with existing
conditions in 2011 showed best trial roughness coefficient for the
main channel of 0.026. The simulated water surface levels fitted to
observation data with R2 of 0.8175. The model was applied to 3
proposed cascade weirs with 2.35 m in height and found surcharge
water level only 0.27 m higher than the existing condition in 2011.
Moreover, those weirs could maintain river water levels and increase
of those pumping performances during less river flow in 2013.
Abstract: In recent years, real estate prediction or valuation has
been a topic of discussion in many developed countries. Improper
hype created by investors leads to fluctuating prices of real estate,
affecting many consumers to purchase their own homes. Therefore,
scholars from various countries have conducted research in real estate
valuation and prediction. With the back-propagation neural network
that has been popular in recent years and the orthogonal array in the
Taguchi method, this study aimed to find the optimal parameter
combination at different levels of orthogonal array after the system
presented different parameter combinations, so that the artificial
neural network obtained the most accurate results. The experimental
results also demonstrated that the method presented in the study had a
better result than traditional machine learning. Finally, it also showed
that the model proposed in this study had the optimal predictive effect,
and could significantly reduce the cost of time in simulation operation.
The best predictive results could be found with a fewer number of
experiments more efficiently. Thus users could predict a real estate
transaction price that is not far from the current actual prices.
Abstract: An analysis of a synchronous generator in a bond
graph approach is proposed. This bond graph allows to determine the
simplified models of the system by using singular perturbations.
Firstly, the nonlinear bond graph of the generator is linearized. Then,
the slow and fast state equations by applying singular perturbations
are obtained. Also, a bond graph to get the quasi-steady state of the
slow dynamic is proposed. In order to verify the effectiveness of the
singularly perturbed models, simulation results of the complete
system and reduced models are shown.
Abstract: This paper presents a mean for reducing the torque
variation during the revolution of a vertical-axis wind turbine
(VAWT) by increasing the blade number. For this purpose, twodimensional
CDF analysis have been performed on a straight-bladed
Darreius-type rotor. After describing the computational model, a
complete campaign of simulations based on full RANS unsteady
calculations is proposed for a three, four and five-bladed rotor
architecture characterized by a NACA 0025 airfoil. For each
proposed rotor configuration, flow field characteristics are
investigated at several values of tip speed ratio, allowing a
quantification of the influence of blade number on flow geometric
features and dynamic quantities, such as rotor torque and power.
Finally, torque and power curves are compared for the analyzed
architectures, achieving a quantification of the effect of blade number
on overall rotor performance.
Abstract: Data gathering is an essential operation in wireless
sensor network applications. So it requires energy efficiency
techniques to increase the lifetime of the network. Similarly,
clustering is also an effective technique to improve the energy
efficiency and network lifetime of wireless sensor networks. In this
paper, an energy efficient cluster formation protocol is proposed with
the objective of achieving low energy dissipation and latency without
sacrificing application specific quality. The objective is achieved by
applying randomized, adaptive, self-configuring cluster formation
and localized control for data transfers. It involves application -
specific data processing, such as data aggregation or compression.
The cluster formation algorithm allows each node to make
independent decisions, so as to generate good clusters as the end.
Simulation results show that the proposed protocol utilizes minimum
energy and latency for cluster formation, there by reducing the
overhead of the protocol.
Abstract: The paper researched and presented a virtual simulation system based on a full-digital lunar terrain, integrated with kinematics and dynamics module as well as autonomous navigation simulation module. The system simulation models are established. Enabling technologies such as digital lunar surface module, kinematics and dynamics simulation, Autonomous navigation are investigated. A prototype system for lunar rover locomotion simulation is developed based on these technologies. Autonomous navigation is a key echnology in lunar rover system, but rarely involved in virtual simulation system. An autonomous navigation simulation module have been integrated in this prototype system, which was proved by the simulation results that the synthetic simulation and visualizing analysis system are established in the system, and the system can provide efficient support for research on the autonomous navigation of lunar rover.
Abstract: Avionics software is safe-critical embedded software
and its architecture is evolving from traditional federated architectures
to Integrated Modular Avionics (IMA) to improve resource usability.
ARINC 653 (Avionics Application Standard Software Interface) is a
software specification for space and time partitioning in Safety-critical
avionics Real-time operating systems. Arinc653 uses two-level
scheduling strategies, but current modeling tools only apply to simple
problems of Arinc653 two-level scheduling, which only contain time
property. In avionics industry, we are always manually allocating
tasks and calculating the timing table of a real-time system to ensure
it-s running as we design. In this paper we represent an automatically
generating strategy which applies to the two scheduling problems with
dependent constraints in Arinc653 partition run-time environment. It
provides the functionality of automatic generation from the task and partition models to scheduling policy through allocating the tasks to the partitions while following the constraints, and then we design a simulating mechanism to check whether our policy is schedulable or
not
Abstract: The automatic construction of large, high-resolution
image vistas (mosaics) is an active area of research in the fields of
photogrammetry [1,2], computer vision [1,4], medical image
processing [4], computer graphics [3] and biometrics [8]. Image
stitching is one of the possible options to get image mosaics. Vista
Creation in image processing is used to construct an image with a
large field of view than that could be obtained with a single
photograph. It refers to transforming and stitching multiple images
into a new aggregate image without any visible seam or distortion in
the overlapping areas. Vista creation process aligns two partial
images over each other and blends them together. Image mosaics
allow one to compensate for differences in viewing geometry. Thus
they can be used to simplify tasks by simulating the condition in
which the scene is viewed from a fixed position with single camera.
While obtaining partial images the geometric anomalies like rotation,
scaling are bound to happen. To nullify effect of rotation of partial
images on process of vista creation, we are proposing rotation
invariant vista creation algorithm in this paper. Rotation of partial
image parts in the proposed method of vista creation may introduce
some missing region in the vista. To correct this error, that is to fill
the missing region further we have used image inpainting method on
the created vista. This missing view regeneration method also
overcomes the problem of missing view [31] in vista due to cropping,
irregular boundaries of partial image parts and errors in digitization
[35]. The method of missing view regeneration generates the missing
view of vista using the information present in vista itself.
Abstract: The theatre-auditorium under investigation following
the highly reflective characteristics of materials used in it (marble,
painted wood, smooth plaster, etc), architectural and structural
features of the Protocol and its intended use (very multifunctional:
Auditorium, theatre, cinema, musicals, conference room) from the
analysis of the statement of fact made by the acoustic simulation
software Ramsete and supported by data obtained through a
campaign of acoustic measurements of the state of fact made on the
spot by a Fonomet Svantek model SVAN 957, appears to be
acoustically inadequate. After the completion of the 3D model
according to the specifications necessary software used forecast in
order to be recognized by him, have made three simulations, acoustic
simulation of the state of and acoustic simulation of two design
solutions.
Improved noise characteristics found in the first design solution,
compared to the state in fact consists therefore in lowering
Reverberation Time that you turn most desirable value, while the
Indicators of Clarity, the Baricentric Time, the Lateral Efficiency,
Ratio of Low Tmedia BR and defined the Speech Intelligibility
improved significantly. Improved noise characteristics found instead
in the second design solution, as compared to first design solution, is
finally mostly in a more uniform distribution of Leq and in lowering
Reverberation Time that you turn the optimum values. Indicators of
Clarity, and the Lateral Efficiency improve further but at the expense
of a value slightly worse than the BR. Slightly vary the remaining
indices.
Abstract: This article simulates the wind generator set which has
two fault bearing collar rail destruction and the gear box oil leak fault.
The electric current signal which produced by the generator, We use
Empirical Mode Decomposition (EMD) as well as Fast Fourier
Transform (FFT) obtains the frequency range-s signal figure and
characteristic value. The last step is use a kind of Artificial Neural
Network (ANN) classifies which determination fault signal's type and
reason. The ANN purpose of the automatic identification wind
generator set fault..
Abstract: The presented work is motivated by a french law regarding nuclear waste management. In order to avoid the limitation coming with the usage of the existing scenario codes, as COSI, VISION or FAMILY, the Core Library for Advance Scenario Simulation (CLASS) is being develop. CLASS is an open source tool, which allows any user to simulate an electronuclear scenario. The main CLASS asset, is the possibility to include any type of reactor, even a complitely new concept, through the generation of its ACSII evolution database. In the present article, the CLASS working basis will be presented as well as a simple exemple in order to show his potentiel. In the considered exemple, the effect of the transmutation will be assessed on Minor Actinide Inventory produced by PWR reactors.
Abstract: Temperature is one of the most principle factors affects aquaculture system. It can cause stress and mortality or superior environment for growth and reproduction. This paper presents the control of pond water temperature using artificial intelligence technique. The water temperature is very important parameter for shrimp growth. The required temperature for optimal growth is 34oC, if temperature increase up to 38oC it cause death of the shrimp, so it is important to control water temperature. Solar thermal water heating system is designed to supply an aquaculture pond with the required hot water in Mersa Matruh in Egypt. Neural networks are massively parallel processors that have the ability to learn patterns through a training experience. Because of this feature, they are often well suited for modeling complex and non-linear processes such as those commonly found in the heating system. Artificial neural network is proposed to control water temperature due to Artificial intelligence (AI) techniques are becoming useful as alternate approaches to conventional techniques. They have been used to solve complicated practical problems. Moreover this paper introduces a complete mathematical modeling and MATLAB SIMULINK model for the aquaculture system. The simulation results indicate that, the control unit success in keeping water temperature constant at the desired temperature by controlling the hot water flow rate.
Abstract: As a result of the daily workflow in the design
development departments of companies, databases containing huge
numbers of 3D geometric models are generated. According to the
given problem engineers create CAD drawings based on their design
ideas and evaluate the performance of the resulting design, e.g. by
computational simulations. Usually, new geometries are built either
by utilizing and modifying sets of existing components or by adding
single newly designed parts to a more complex design.
The present paper addresses the two facets of acquiring
components from large design databases automatically and providing
a reasonable overview of the parts to the engineer. A unified
framework based on the topographic non-negative matrix
factorization (TNMF) is proposed which solves both aspects
simultaneously. First, on a given database meaningful components
are extracted into a parts-based representation in an unsupervised
manner. Second, the extracted components are organized and
visualized on square-lattice 2D maps. It is shown on the example of
turbine-like geometries that these maps efficiently provide a wellstructured
overview on the database content and, at the same time,
define a measure for spatial similarity allowing an easy access and
reuse of components in the process of design development.
Abstract: In this paper, zigbee communication based wireless energy surveillance system is presented. The proposed system consists of multiple energy surveillance devices and an energy surveillance monitor. Each different standby power-off value of electric device is set automatically by using learning function of energy surveillance device. Thus adaptive standby power-off function provides user convenience and it maximizes the energy savings. Also, power consumption monitoring function is helpful to reduce inefficient energy consumption in home. The zigbee throughput simulator is designed to evaluate minimum transmission power and maximum allowable information quantity in the proposed system. The test result of prototype has been satisfied all the requirements. The proposed system has confirmed that can be used as an intelligent energy surveillance system for energy savings in home or office.
Abstract: This paper presents the generation of bipolar square
wave pulses with characteristics that are suitable for liquid food
sterilization using a Cascaded H-bridge Multilevel Inverter (CHMI).
Bipolar square waves pulses have been reported as stable for a
longer time during the sterilization process with minimum heat
emission and increased efficiency. The CHMI allows the system to
produce bipolar square wave pulses and yielding high output voltage
without using a transformer while fulfilling the pulse requirements
for effective liquid food sterilization. This in turn can reduce power
consumption and cost of the overall liquid food sterilization system.
The simulation results have shown that pulses with peak output
voltage of 2.4 kV, pulse width of between 1 2s and 1 ms at
frequencies of 50 Hz and 100 Hz can be generated by a 7-level
CHMI. Results from the experimental set-up based on a 5-level
CHMI has indicated the potential of the proposed circuit in
producing bipolar square wave output pulses with peak values that
depends on the DC source level supplied to the CHMI modules,
pulse width of between 12.5 2s and 1 ms at frequencies of 50 Hz
and 100 Hz.
Abstract: In the current work, a numerical parametric study was
performed in order to model the fluid mechanics in the riser of a
bubbling fluidized bed (BFB). The gas-solid flow was simulated by
mean of a multi-fluid Eulerian model incorporating the kinetic theory
for solid particles. The bubbling fluidized bed was simulated two
dimensionally by mean of a Computational Fluid Dynamic (CFD)
commercial software package, Fluent. The effects of using different
inter-phase drag function (the drag model of Gidaspow, Syamlal and
O-Brien and the EMMS drag model) on the model predictions were
evaluated and compared. The results showed that the drag models of
Gidaspow and Syamlal and O-Brien overestimated the drag force for
the FCC particles and predicted a greater bed expansion in
comparison to the EMMS drag model.
Abstract: To improve the characterization of blood flows, we propose a method which makes it possible to use the spectral analysis
of the Doppler signals. Our calculation induces a reasonable approximation, the error made on estimated speed reflects the fact
that speed depends on the flow conditions as well as on measurement parameters like the bore and the volume flow rate. The estimate of the Doppler signal frequency enables us to determine the maximum Doppler frequencie Fd max as well as the maximum flow speed. The
results show that the difference between the estimated frequencies
( Fde ) and the Doppler frequencies ( Fd ) is small, this variation tends to zero for important θ angles and it is proportional to the diameter D. The description of the speed of friction and the
coefficient of friction justify the error rate obtained.
Abstract: Virtualization-based server consolidation has been
proven to be an ideal technique to solve the server sprawl problem by
consolidating multiple virtualized servers onto a few physical servers
leading to improved resource utilization and return on investment. In
this paper, we solve this problem by using existing servers, which are
heterogeneous and diversely preferred by IT managers. Five practical
consolidation rules are introduced, and a decision model is proposed to
optimally allocate source services to physical target servers while
maximizing the average resource utilization and preference value. Our
model can be regarded as a multi-objective multi-dimension
bin-packing (MOMDBP) problem with constraints, which is strongly
NP-hard. An improved grouping generic algorithm (GGA) is
introduced for the problem. Extensive simulations were performed and
the results are given.
Abstract: Since the last two decades, container transportation
system has been faced under increasing development. This fact
shows the importance of container transportation system as a key role
of container terminals to link between sea and land. Therefore, there
is a continuous need for the optimal use of equipment and facilities in
the ports. Regarding the complex structure of container ports, this
paper presents a simulation model that compares tow storage
strategies for storing containers in the yard. For this purpose, we
considered loading and unloading norm as an important criterion to
evaluate the performance of Shahid Rajaee container port. By
analysing the results of the model, it will be shown that using
marshalling yard policy instead of current storage system has a
significant effect on the performance level of the port and can
increase the loading and unloading norm up to 14%.