Abstract: Voltage collapse is instability of heavily loaded electric
power systems that cause to declining voltages and blackout. Power
systems are predicated to become more heavily loaded in the future
decade as the demand for electric power rises while economic and
environmental concerns limit the construction of new transmission
and generation capacity. Heavily loaded power systems are closer to
their stability limits and voltage collapse blackouts will occur if
suitable monitoring and control measures are not taken. To control
transmission lines, it can be used from FACTS devices.
In this paper Harmony search algorithm (HSA) and Genetic
Algorithm (GA) have applied to determine optimal location of
FACTS devices in a power system to improve power system stability.
Three types of FACTS devices (TCPAT, UPFS, and SVC) have been
introduced. Bus under voltage has been solved by controlling reactive
power of shunt compensator. Also a combined series-shunt
compensators has been also used to control transmission power flow
and bus voltage simultaneously.
Different scenarios have been considered. First TCPAT, UPFS, and
SVC are placed solely in transmission lines and indices have been
calculated. Then two types of above controller try to improve
parameters randomly. The last scenario tries to make better voltage
stability index and losses by implementation of three types controller
simultaneously. These scenarios are executed on typical 34-bus test
system and yields efficiency in improvement of voltage profile and
reduction of power losses; it also may permit an increase in power
transfer capacity, maximum loading, and voltage stability margin.
Abstract: New generation mobile communication networks have
the ability of supporting triple play. In order that, Orthogonal
Frequency Division Multiplexing (OFDM) access techniques have
been chosen to enlarge the system ability for high data rates
networks. Many of cross-layer modeling and optimization schemes
for Quality of Service (QoS) and capacity of downlink multiuser
OFDM system were proposed. In this paper, the Maximum Weighted
Capacity (MWC) based resource allocation at the Physical (PHY)
layer is used. This resource allocation scheme provides a much better
QoS than the previous resource allocation schemes, while
maintaining the highest or nearly highest capacity and costing similar
complexity. In addition, the Delay Satisfaction (DS) scheduling at the
Medium Access Control (MAC) layer, which allows more than one
connection to be served in each slot is used. This scheduling
technique is more efficient than conventional scheduling to
investigate both of the number of users as well as the number of
subcarriers against system capacity. The system will be optimized for
different operational environments: the outdoor deployment scenarios
as well as the indoor deployment scenarios are investigated and also
for different channel models. In addition, effective capacity approach
[1] is used not only for providing QoS for different mobile users, but
also to increase the total wireless network's throughput.
Abstract: In this work, a Modified Functional Link Artificial
Neural Network (M-FLANN) is proposed which is simpler than a
Multilayer Perceptron (MLP) and improves upon the universal
approximation capability of Functional Link Artificial Neural
Network (FLANN). MLP and its variants: Direct Linear Feedthrough
Artificial Neural Network (DLFANN), FLANN and
M-FLANN have been implemented to model a simulated Water Bath
System and a Continually Stirred Tank Heater (CSTH). Their
convergence speed and generalization ability have been compared.
The networks have been tested for their interpolation and
extrapolation capability using noise-free and noisy data. The results
show that M-FLANN which is computationally cheap, performs
better and has greater generalization ability than other networks
considered in the work.
Abstract: The scalar wave equation for a potential in a curved space time, i.e., the Laplace-Beltrami equation has been studied in this work. An action principle is used to derive a finite element algorithm for determining the modes of propagation inside a waveguide of arbitrary shape. Generalizing this idea, the Maxwell theory in a curved space time determines a set of linear partial differential equations for the four electromagnetic potentials given by the metric of space-time. Similar to the Einstein-s formulation of the field equations of gravitation, these equations are also derived from an action principle. In this paper, the expressions for the action functional of the electromagnetic field have been derived in the presence of gravitational field.
Abstract: On the basis of questionnaires and interviews of two samples of subjects (French and Anglo-Saxon) for which two food products were presented (one of the subject’s country and one of the foreign country), we have shown how consumers could be sensitive to the label or brand written on the package of the food product. Furthermore, in the light of Intersubjectivity theory, we have shown the necessity for the consumer to find congruence between the direct and meta perspective towards the product for which the producer and especially the marketer is responsible. Taking into account these findings may help to avoid the commercial failure of a brand while exported abroad.
Abstract: The cDNA encoding the 326 amino acids of a Class I
basic chitinase gene from Leucaena leucocephala de Wit (KB3,
Genbank accession: AAM49597) was cloned under the control of
CaMV35S promoter in pCAMBIA 1300 and transferred to
Koshihikari. Calli of Koshihikari rice was transformed with
agrobacterium with this construct expressing the chitinase and β-
glucouronidase (GUS). The frequencies of calli 90 % has been
obtained from rice seedlings cultured on NB medium. The high
regeneration frequencies, 74% was obtained from calli cultured on
regeneration medium containing 4 mg/l BAP, and 7 g/l phytagel at
25°C. Various factors were studied in order to establish a procedure
for the transformation of Koshihikari Agrobacterium tumefaciens.
Supplementation of 50 mM acetosyringone to the medium during
coculivation was important to enhance the frequency to transient
transformation. The 4 week-old scutellum-derived calli were
excellent starting materials. Selection medium based on NB medium
supplement with 40 mg/l hygromycin and 400 mg/l cefotaxime were
an optimized medium for selection of transformed rice calli. The
percentage of transformation 70 was obtained. Recombinant calli and
regenerated rice plants were checked the expression of chitinase and
gus by PCR, northern blot gel, southern blot gel, and gus assay.
Chitinase and gus were expressed in all parts of recombinant rice.
The rice line expressing the KB3 chiitnase was more resistant to the
blast fungus Fusarium monoliforme than control line.
Abstract: Blood pulse is an important human physiological signal commonly used for the understanding of the individual physical health. Current methods of non-invasive blood pulse sensing require direct contact or access to the human skin. As such, the performances of these devices tend to vary with time and are subjective to human body fluids (e.g. blood, perspiration and skin-oil) and environmental contaminants (e.g. mud, water, etc). This paper proposes a simulation model for the novel method of non-invasive acquisition of blood pulse using the disturbance created by blood flowing through a localized magnetic field. The simulation model geometry represents a blood vessel, a permanent magnet, a magnetic sensor, surrounding tissues and air in 2-dimensional. In this model, the velocity and pressure fields in the blood stream are described based on Navier-Stroke equations and the walls of the blood vessel are assumed to have no-slip condition. The blood assumes a parabolic profile considering a laminar flow for blood in major artery near the skin. And the inlet velocity follows a sinusoidal equation. This will allow the computational software to compute the interactions between the magnetic vector potential generated by the permanent magnet and the magnetic nanoparticles in the blood. These interactions are simulated based on Maxwell equations at the location where the magnetic sensor is placed. The simulated magnetic field at the sensor location is found to assume similar sinusoidal waveform characteristics as the inlet velocity of the blood. The amplitude of the simulated waveforms at the sensor location are compared with physical measurements on human subjects and found to be highly correlated.
Abstract: An optical fiber Fabry-Perot interferometer (FFPI) is
proposed and demonstrated for dynamic measurements in a
mechanical vibrating target. A polishing metal with a low reflectance
value adhered to a mechanical vibrator was excited via a function
generator at various excitation frequencies. Output interference
fringes were generated by modulating the reference and sensing
signal at the output arm. A fringe-counting technique was used for
interpreting the displacement information on the dedicated computer.
The fiber interferometer has been found the capability of the
displacement measurements of 1.28 μm – 96.01 μm. A commercial
displacement sensor was employed as a reference sensor for
investigating the measurement errors from the fiber sensor. A
maximum percentage measurement error of approximately 1.59 %
was obtained.
Abstract: Software Development Risks Identification (SDRI),
using Fault Tree Analysis (FTA), is a proposed technique to identify
not only the risk factors but also the causes of the appearance of the
risk factors in software development life cycle. The method is based
on analyzing the probable causes of software development failures
before they become problems and adversely affect a project. It uses
Fault tree analysis (FTA) to determine the probability of a particular
system level failures that are defined by A Taxonomy for Sources of
Software Development Risk to deduce failure analysis in which an
undesired state of a system by using Boolean logic to combine a
series of lower-level events. The major purpose of this paper is to use
the probabilistic calculations of Fault Tree Analysis approach to
determine all possible causes that lead to software development risk
occurrence
Abstract: Abstract–Indoor air (VOCs) samples were collected
simultaneously from variety of indoors (e.g. living rooms, baby-s
rooms) and outdoor environments which were voluntarily selected
from the houses in which pregnant residents live throughout Ankara.
This is the first comprehensive study done in Turkey starting from
prenatal period and continued till the babies had one year old. VOCs
levels were measured over 76 homes. Air samples were collected in
Tenax TA sorbent filled tubes with active sampling method and
analyzed with Thermal Desorber and Gas Chromatography/Mass
spectrometry (TD-GC/MS). At the first sampling period in the baby-s
rooms maximum concentration of toluene was measured about
240.77μg.m-3 and in the living rooms maximum concentration of
naphthalene was 180.24μg.m-3. At the second sampling period in the
baby-s rooms maximum concentration of toluene was measured
about 144.97μg.m-3 and in the living rooms maximum concentration
of naphthalene was 247.89μg.m-3. Concentration of TVOCs in the
first period was generally higher than the second period.
Abstract: Recycling of aluminum alloys often decrease fluidity,
consequently influence the castability of the alloy. In this study, the
fluidity of Al-Zn alloys, such as the standard A713 alloy with and
without scrap addition has been investigated. The scrap added was
comprised of contaminated alloy turning chips. Fluidity
measurements were performed with double spiral fluidity test
consisting of gravity casting of double spirals in green sand moulds
with good reproducibility. The influence of recycled alloy on fluidity
has been compared with that of the virgin alloy and the results
showed that the fluidity decreased with the increase in recycled alloy
at minimum pouring temperatures. Interestingly, an appreciable
improvement in the fluidity was observed at maximum pouring
temperature, especially for coated spirals.
Abstract: Acid rain occurs when sulphur dioxide (SO2) and
nitrogen oxides (Nox) gases react in the atmosphere with water,
oxygen, and other chemicals to form various acidic compounds. The
result is a mild solution of sulfuric acid and nitric acid. Soil has a
greater buffering capacity than aquatic systems. However excessive
amount of acids introduced by acid rains may disturb the entire soil
chemistry. Acidity and harmful action of toxic elements damage
vegetation while susceptible microbial species are eliminated. In
present study, the effects of simulated sulphuric acid and nitric acid
rains were investigated on crop Glycine max. The effect of acid rain
on change in soil fertility was detected in which pH of control sample
was 6.5 and pH of 1%H2SO4 and 1%HNO3 were 3.5. Nitrogen nitrate
in soil was high in 1% HNO3 treated soil & Control sample.
Ammonium nitrogen in soil was low in 1% HNO3 & H2SO4 treated
soil. Ammonium nitrogen was medium in control and other samples.
The effect of acid rain on seed germination on 3rd day of germination
control sample growth was 7 cm, 0.1% HNO3 was 8cm, and 0.001%
HNO3 & 0.001% H2SO4 was 6cm each. On 10th day fungal growth
was observed in 1% and 0.1%H2SO4 concentrations, when all plants
were dead. The effect of acid rain on crop productivity was
investigated on 3rd day roots were developed in plants. On12th day
Glycine max showed more growth in 0.1% HNO3, 0.001% HNO3 and
0.001% H2SO4 treated plants growth were same as compare to control
plants. On 20th day development of discoloration of plant pigments
were observed on acid treated plants leaves. On 38th day, 0.1, 0.001%
HNO3 and 0.1, 0.001% H2SO4 treated plants and control plants were
showing flower growth. On 42th day, acid treated Glycine max variety
and control plants were showed seeds on plants. In Glycine max
variety 0.1, 0.001% H2SO4, 0.1, 0.001% HNO3 treated plants were
dead on 46th day and fungal growth was observed. The toxicological
study was carried out on Glycine max plants exposed to 1% HNO3
cells were damaged more than 1% H2SO4. Leaf sections exposed to
0.001% HNO3 & H2SO4 showed less damaged of cells and
pigmentation observed in entire slide when compare with control
plant. The soil analysis was done to find microorganisms in HNO3 &
H2SO4 treated Glycine max and control plants. No microorganism
growth was observed in 1% HNO3 & H2SO4 but control plant showed
microbial growth.
Abstract: Removal of a reactive dye (Reactive blue 4) by
adsorption utilizing waste aluminium hydroxide sludge as an
adsorbent was investigated. The removal of the dye was optimized
using response surface methodology (RSM). In the RSM
experiments; initial dye concentration, adsorbent concentration and
contact time were critical parameters. RSM experiments were
performed at the range of initial dye concentration 31.82-368.18
mg/L, adsorbent concentration 3.18-36.82 g/L, contact time 15.82-
56.18 h. Optimum initial dye concentration, adsorbent concentration
and contact time were obtained as 108.83 mg/L, 29.36 g/L and 33.57
h respectively. At these conditions, maximum removal of the dye was
obtained as 95%. The experiments were performed at the optimum
conditions to verify these results and the same results were obtained.
Abstract: This research proposes an algorithm for the simulation
of time-periodic unsteady problems via the solution unsteady Euler
and Navier-Stokes equations. This algorithm which is called Time
Spectral method uses a Fourier representation in time and hence
solve for the periodic state directly without resolving transients
(which consume most of the resources in a time-accurate scheme).
Mathematical tools used here are discrete Fourier transformations. It
has shown tremendous potential for reducing the computational cost
compared to conventional time-accurate methods, by enforcing
periodicity and using Fourier representation in time, leading to
spectral accuracy. The accuracy and efficiency of this technique is
verified by Euler and Navier-Stokes calculations for pitching airfoils.
Because of flow turbulence nature, Baldwin-Lomax turbulence
model has been used at viscous flow analysis. The results presented
by the Time Spectral method are compared with experimental data. It
has shown tremendous potential for reducing the computational cost
compared to the conventional time-accurate methods, by enforcing
periodicity and using Fourier representation in time, leading to
spectral accuracy, because results verify the small number of time
intervals per pitching cycle required to capture the flow physics.
Abstract: This paper reports the fatigue crack growth behaviour
of gas tungsten arc, electron beam and laser beam welded Ti-6Al-4V
titanium alloy. Centre cracked tensile specimens were prepared to
evaluate the fatigue crack growth behaviour. A 100kN servo
hydraulic controlled fatigue testing machine was used under constant
amplitude uniaxial tensile load (stress ratio of 0.1 and frequency of
10 Hz). Crack growth curves were plotted and crack growth
parameters (exponent and intercept) were evaluated. Critical and
threshold stress intensity factor ranges were also evaluated. Fatigue
crack growth behaviour of welds was correlated with mechanical
properties and microstructural characteristics of welds. Of the three
joints, the joint fabricated by laser beam welding exhibited higher
fatigue crack growth resistance due to the presence of fine lamellar
microstructure in the weld metal.
Abstract: This paper present the implementation of a new ordering strategy on Successive Overrelaxation scheme on two dimensional boundary value problems. The strategy involve two directions alternatingly; from top and bottom of the solution domain. The method shows to significantly reduce the iteration number to converge. Four numerical experiments were carried out to examine the performance of the new strategy.
Abstract: Transmission network expansion planning (TNEP) is
a basic part of power system planning that determines where, when
and how many new transmission lines should be added to the
network. Up till now, various methods have been presented to solve
the static transmission network expansion planning (STNEP)
problem. But in all of these methods, transmission expansion
planning considering network adequacy restriction has not been
investigated. Thus, in this paper, STNEP problem is being studied
considering network adequacy restriction using discrete particle
swarm optimization (DPSO) algorithm. The goal of this paper is
obtaining a configuration for network expansion with lowest
expansion cost and a specific adequacy. The proposed idea has been
tested on the Garvers network and compared with the decimal
codification genetic algorithm (DCGA). The results show that the
network will possess maximum efficiency economically. Also, it is
shown that precision and convergence speed of the proposed DPSO
based method for the solution of the STNEP problem is more than
DCGA approach.
Abstract: LES with mixed subgrid-scale model has been used to
simulate aerodynamic performance of hypersonic configuration. The
simulation was conducted to replicate conditions and geometry of a
model which has been previously tested. LES Model has been
successful in predict pressure coefficient with the max error 1.5%
besides afterbody. But in the high Mach number condition, it is poor in
predict ability and product 12.5% error. The calculation error are
mainly conducted by the distribution swirling. The fact of poor ability
in the high Mach number and afterbody region indicated that the
mixed subgrid-scale model should be improved in large eddied
especially in hypersonic separate region. In the condition of attach and
sideslip flight, the calculation results have waves. LES are successful
in the prediction the pressure wave in hypersonic flow.
Abstract: In this paper we proposed multistage adaptive
ARQ/HARQ/HARQ scheme. This method combines pure ARQ
(Automatic Repeat reQuest) mode in low channel bit error rate and
hybrid ARQ method using two different Reed-Solomon codes in
middle and high error rate conditions. It follows, that our scheme has
three stages. The main goal is to increase number of states in adaptive
HARQ methods and be able to achieve maximum throughput for
every channel bit error rate. We will prove the proposal by
calculation and then with simulations in land mobile satellite channel
environment. Optimization of scheme system parameters is described
in order to maximize the throughput in the whole defined Signal-to-
Noise Ratio (SNR) range in selected channel environment.
Abstract: The main aim of this work is to establish the
capabilities of new green buildings to ascertain off-grid electricity
generation based on the integration of wind turbines in the
conceptual model of a rotating tower [2] in Dubai. An in depth
performance analysis of the WinWind 3.0MW [3] wind turbine is
performed. Data based on the Dubai Meteorological Services is
collected and analyzed in conjunction with the performance analysis
of this wind turbine. The mathematical model is compared with
Computational Fluid Dynamics (CFD) results based on a conceptual
rotating tower design model. The comparison results are further
validated and verified for accuracy by conducting experiments on a
scaled prototype of the tower design. The study concluded that
integrating wind turbines inside a rotating tower can generate enough
electricity to meet the required power consumption of the building,
which equates to a wind farm containing 9 horizontal axis wind
turbines located at an approximate area of 3,237,485 m2 [14].