Abstract: Polyurethanes (PURs) are very versatile polymeric
materials with a wide range of physical and chemical properties.
PURs have desirable properties such as high abrasion resistance, tear
strength, shock absorption, flexibility and elasticity. Although they
have relatively poor thermal stability, this can be improved by using
treated clay. Polyurethane/clay nanocomposites have been
synthesized from renewable sources. A polyol for the production of
polyurethane by reaction with an isocyanate was obtained by the
synthesis of palm oil-based oleic acid with glycerol. Dodecylbenzene
sulfonic acid (DBSA) was used as catalyst and emulsifier. The
unmodified clay (kunipia-F) was treated with cetyltrimethyl
ammonium bromide (CTAB-mont) and octadodecylamine (ODAmont).
The d-spacing in CTAB-mont and ODA-mont were 1.571 nm
and 1.798 nm respectively and larger than that of the pure-mont
(1.142 nm). The organoclay was completely intercalated in the
polyurethane, as confirmed by a wide angle x-ray diffraction
(WAXD) pattern.
The results showed that adding clay demonstrated better thermal
stability in comparison with the virgin polyurethane. Onset
degradation of pure PU is at 200oC, and is lower than that of the
CTAB-mont PU and ODA-mont PU which takes place at about
318oC and 330oC, respectively. The mechanical properties (including
the dynamic mechanical properties) of pure polyurethane (PU) and
PU/clay nanocomposites, were measured. The modified organoclay
had a remarkably beneficial effect on the strength and elongation at
break of the nanocomposites, which both increased with increasing
clay content with the increase of the tensile strength of more than
214% and 267% by the addition of only 5 wt% of the
montmorillonite CTAB-mont PU and ODA-mont PU, respectively.
Abstract: We investigated the response of testosterone (T),
growth hormone (GH), cortisol (C), steroid hormone binding
globulin (SHBG), insulin-like growth factor (IGF-1), insulin-like
growth factor binding protein-3 (IGFBP-3), and some anaboliccatabolic
indexes, i.e.: T/C, T/SHBG, and IGF-1/IGFBP-3 to
maximal exercise in endurance-trained athletes (TREN) and
untrained subjects (CG). The baseline concentration of IGF-1 was
higher in athletes (TREN) when compared to the CG (p
Abstract: In this study the elastic-plastic stress distribution in
weld-bonded joint, fabricated from austenitic stainless steel (AISI
304) sheet of 1.00 mm thickness and Epoxy adhesive Araldite 2011,
subjected to axial loading is investigated. This is needed to improve
design procedures and welding codes, and saving efforts in the
cumbersome experiments and analysis. Therefore, a complete 3-D
finite element modelling and analysis of spot welded, bonded and
weld-bonded joints under axial loading conditions is carried out. A
comprehensive systematic experimental program is conducted to
determine many properties and quantities, of the base metals and the
adhesive, needed for FE modelling, such like the elastic – plastic
properties, modulus of elasticity, fracture limit, the nugget and heat
affected zones (HAZ) properties, etc. Consequently, the finite
element models developed, for each case, are used to evaluate
stresses distributions across the entire joint, in both the elastic and
plastic regions. The stress distribution curves are obtained,
particularly in the elastic regions and found to be consistent and in
excellent agreement with the published data. Furthermore, the
stresses distributions are obtained in the weld-bonded joint and
display the best results with almost uniform smooth distribution
compared to spot and bonded cases. The stress concentration peaks at
the edges of the weld-bonded region, are almost eliminated resulting
in achieving the strongest joint of all processes.
Abstract: In this paper a polymer electrolyte membrane (PEM)
fuel cell power system including burner, steam reformer, heat
exchanger and water heater has been considered to meet the
electrical, heating, cooling and domestic hot water loads of
residential building which in Tehran. The system uses natural gas as
fuel and works in CHP mode. Design and operating conditions of a
PEM fuel cell system is considered in this study. The energy
requirements of residential building and the number of fuel cell
stacks to meet them have been estimated. The method involved
exergy analysis and entropy generation thorough the months of the
year. Results show that all the energy needs of the building can be
met with 12 fuel cell stacks at a nominal capacity of 8.5 kW. Exergy
analysis of the CHP system shows that the increase in the ambient air
temperature from 1oC to 40oC, will have an increase of entropy
generation by 5.73%.Maximum entropy generates for 15 hour in 15th
of June and 15th of July is estimated to amount at 12624 (kW/K).
Entropy generation of this system through a year is estimated to
amount to 1004.54 GJ/k.year.
Abstract: This paper proposes a VPN Accelerator Board
(VPN-AB), a virtual private network (VPN) protocol designed for
trust channel security system (TCSS). TCSS supports safety
communication channel between security nodes in internet. It
furnishes authentication, confidentiality, integrity, and access control
to security node to transmit data packets with IPsec protocol. TCSS
consists of internet key exchange block, security association block,
and IPsec engine block. The internet key exchange block negotiates
crypto algorithm and key used in IPsec engine block. Security
Association blocks setting-up and manages security association
information. IPsec engine block treats IPsec packets and consists of
networking functions for communication. The IPsec engine block
should be embodied by H/W and in-line mode transaction for high
speed IPsec processing. Our VPN-AB is implemented with high speed
security processor that supports many cryptographic algorithms and
in-line mode. We evaluate a small TCSS communication environment,
and measure a performance of VPN-AB in the environment. The
experiment results show that VPN-AB gets a performance throughput
of maximum 15.645Gbps when we set the IPsec protocol with
3DES-HMAC-MD5 tunnel mode.
Abstract: Inventory decisional environment of short life-cycle
products is full of uncertainties arising from randomness and
fuzziness of input parameters like customer demand requiring
modeling under hybrid uncertainty. Prior inventory models
incorporating fuzzy demand have unfortunately ignored stochastic
variation of demand. This paper determines an unambiguous optimal
order quantity from a set of n fuzzy observations in a newsvendor
inventory setting in presence of fuzzy random variable demand
capturing both fuzzy perception and randomness of customer
demand. The stress of this paper is in providing solution procedure
that attains optimality in two steps with demand information
availability in linguistic phrases leading to fuzziness along with
stochastic variation. The first step of solution procedure identifies
and prefers one best fuzzy opinion out of all expert opinions and the
second step determines optimal order quantity from the selected
event that maximizes profit. The model and solution procedure is
illustrated with a numerical example.
Abstract: An algorithm for estimating the disparity of objects of
interest is proposed. This algorithm uses image shifting and
overlapping area to estimate the disparity value; thereby depth of the
objects of interest can be obtained. The algorithm is able to perform
at different levels of accuracy. However, as the accuracy increases
the processing speed decreases. The algorithm is tested with static
stereo images and sequence of stereo images. The experimental
results are presented in this paper.
Abstract: A study of electromagnetic flow meter is presented in the paper. Comparison has been made between the analytical and the numerical results by the use of FEM numerical analysis (Quick Field 5.6) for determining polarization voltage through the circle cross section of the polarization transducer. Exciting and geometrical parameters increasing its effectiveness has been examined. The aim is to obtain maximal output signal. The investigations include different variants of the magnetic flux density distribution around the tube: homogeneous field of magnitude Bm, linear distribution with maximal value Bm and trapezium distribution conserving the same exciting magnetic energy as the homogeneous field.
Abstract: This paper presents the utilizing of ferroelectric
material on antenna application. There are two different ferroelectric
had been used on the proposed antennas which include of Barium
Strontium Titanate (BST) and Bismuth Titanate (BiT), suitable for
Access Points operating in the WLAN IEEE 802.11 b/g and WiMAX
IEEE 802.16 within the range of 2.3 GHz to 2.5 GHz application.
BST, which had been tested to own a dielectric constant of εr = 15
while BiT has a dielectric constant that higher than BST which is εr =
21 and both materials are in rectangular shaped. The influence of
various parameters on antenna characteristics were investigated
extensively using commercial electromagnetic simulations software
by Communication Simulation Technology (CST). From theoretical
analysis and simulation results, it was demonstrated that ferroelectric
material used have not only improved the directive emission but also
enhanced the radiation efficiency.
Abstract: The extract of milk thistle contains a mix of flavonolignans termed silymarine.. In order to analysis influence of growth regulators, genotype, explant and subculture on the accumulation of flavonolignans, a study was carried out by using two genotype (Budakalszi and Noor abad moghan cultivars), cotyledon and hypocotyle explants, solid media of MS supplemented by different combinations of two growth regulators; Kinetin (0.1, 1 mg/l) and 2,4-D (1, 2 mg/l). Seeds of the plant were germinated in MS media whitout growth regulators in growth chamber at 26°C and darkness condition. In order to callus induction, the culture media was supplemented whit different concentrations of 2,4-D and kinetin. Calli obtained from explants were sub-cultured four times into the fresh media of the first experiment. flavonoides was extracted from calli in four subcultures. The flavonoid components were determined by high- performance liquid choromatography (HPLC) and separated into Taxifolin, Silydianin+Silychristin, Silybin A+B and Isosilybin A+B. Results showed that with increasing callus age, increased accumulation of silybin A+B, but reduced Isosilybin A+B content. Highest accumulation of Taxifolin was observed at first calli. Calli produced from cotyledon explant of Budakalszi cultivar were superior for Silybin A+B, where calli from hypocotyl explant produced higher amount of Taxifolin and Silydianin+Silychristin. The best cultivar for Silymarin production in this study was Budakalszi cultivar. High amount of SBN A+B and TXF were obtained from hypocotil explant.
Abstract: According to the density of the chips, designers are
trying to put so any facilities of computational and storage on single
chips. Along with the complexity of computational and storage
circuits, the designing, testing and debugging become more and more
complex and expensive. So, hardware design will be built by using
very high speed hardware description language, which is more
efficient and cost effective. This paper will focus on the
implementation of 32-bit ALU design based on Verilog hardware
description language. Adder and subtracter operate correctly on both
unsigned and positive numbers. In ALU, addition takes most of the
time if it uses the ripple-carry adder. The general strategy for
designing fast adders is to reduce the time required to form carry
signals. Adders that use this principle are called carry look- ahead
adder. The carry look-ahead adder is to be designed with combination
of 4-bit adders. The syntax of Verilog HDL is similar to the C
programming language. This paper proposes a unified approach to
ALU design in which both simulation and formal verification can
co-exist.
Abstract: This paper presents an improved variable ordering method to obtain the minimum number of nodes in Reduced Ordered Binary Decision Diagrams (ROBDD). The proposed method uses the graph topology to find the best variable ordering. Therefore the input Boolean function is converted to a unidirectional graph. Three levels of graph parameters are used to increase the probability of having a good variable ordering. The initial level uses the total number of nodes (NN) in all the paths, the total number of paths (NP) and the maximum number of nodes among all paths (MNNAP). The second and third levels use two extra parameters: The shortest path among two variables (SP) and the sum of shortest path from one variable to all the other variables (SSP). A permutation of the graph parameters is performed at each level for each variable order and the number of nodes is recorded. Experimental results are promising; the proposed method is found to be more effective in finding the variable ordering for the majority of benchmark circuits.
Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: Block replacement algorithms to increase hit ratio
have been extensively used in cache memory management. Among
basic replacement schemes, LRU and FIFO have been shown to be
effective replacement algorithms in terms of hit rates. In this paper,
we introduce a flexible stack-based circuit which can be employed in
hardware implementation of both LRU and FIFO policies. We
propose a simple and efficient architecture such that stack-based
replacement algorithms can be implemented without the drawbacks
of the traditional architectures. The stack is modular and hence, a set
of stack rows can be cascaded depending on the number of blocks in
each cache set. Our circuit can be implemented in conjunction with
the cache controller and static/dynamic memories to form a cache
system. Experimental results exhibit that our proposed circuit
provides an average value of 26% improvement in storage bits and its
maximum operating frequency is increased by a factor of two
Abstract: The problem of manipulator control is a highly
complex problem of controlling a system which is multi-input, multioutput,
non-linear and time variant. In this paper some adaptive
fuzzy, and a new hybrid fuzzy control algorithm have been
comparatively evaluated through simulations, for manipulator
control. The adaptive fuzzy controllers consist of self-organizing,
self-tuning, and coarse/fine adaptive fuzzy schemes. These
controllers are tested for different trajectories and for varying
manipulator parameters through simulations. Various performance
indices like the RMS error, steady state error and maximum error are
used for comparison. It is observed that the self-organizing fuzzy
controller gives the best performance. The proposed hybrid fuzzy
plus integral error controller also performs remarkably well, given its
simple structure.
Abstract: In this paper, we construct and implement a new
Steganography algorithm based on learning system to hide a large
amount of information into color BMP image. We have used adaptive
image filtering and adaptive non-uniform image segmentation with
bits replacement on the appropriate pixels. These pixels are selected
randomly rather than sequentially by using new concept defined by
main cases with sub cases for each byte in one pixel. According to
the steps of design, we have been concluded 16 main cases with their
sub cases that covere all aspects of the input information into color
bitmap image. High security layers have been proposed through four
layers of security to make it difficult to break the encryption of the
input information and confuse steganalysis too. Learning system has
been introduces at the fourth layer of security through neural
network. This layer is used to increase the difficulties of the statistical
attacks. Our results against statistical and visual attacks are discussed
before and after using the learning system and we make comparison
with the previous Steganography algorithm. We show that our
algorithm can embed efficiently a large amount of information that
has been reached to 75% of the image size (replace 18 bits for each
pixel as a maximum) with high quality of the output.
Abstract: This paper deals with analysis of flexural stiffness,
indentation and their energies in three point loading of sandwich
beams with composite faces from Eglass/epoxy and cores from
Polyurethane or PVC. Energy is consumed in three stages of
indentation in laminated beam, indentation of sandwich beam and
bending of sandwich beam. Theory of elasticity is chosen to present
equations for indentation of laminated beam, then these equations
have been corrected to offer better results. An analytical model has
been used assuming an elastic-perfectly plastic compressive behavior
of the foam core. Classical theory of beam is used to describe three
point bending. Finite element (FE) analysis of static indentation
sandwich beams is performed using the FE code ABAQUS. The
foam core is modeled using the crushable foam material model and
response of the foam core is experimentally characterized in uniaxial
compression.
Three point bending and indentation have been done
experimentally in two cases of low velocity and higher velocity
(quasi-impact) of loading. Results can describe response of beam in
terms of core and faces thicknesses, core material, indentor diameter,
energy absorbed, and length of plastic area in the testing. The
experimental results are in good agreement with the analytical and
FE analyses. These results can be used as an introduction for impact
loading and energy absorbing of sandwich structures.
Abstract: Utilization of bagasse ash for silica sources is one of
the most common application for agricultural wastes and valuable
biomass byproducts in sugar milling. The high percentage silica
content from bagasse ash was used as silica source for sodium
silicate solution. Different heating temperature, time and acid
treatment were studies for silica extraction. The silica was
characterized using various techniques including X-ray fluorescence,
X-ray diffraction, Scanning electron microscopy, and Fourier
Transform Infrared Spectroscopy method,. The synthesis conditions
were optimized to obtain the bagasse ash with the maximum silica
content. The silica content of 91.57 percent was achieved from
heating of bagasse ash at 600°C for 3 hours under oxygen feeding
and HCl treatment. The result can be used as value added for bagasse
ash utilization and minimize the environmental impact of disposal
problems.
Abstract: The study of the generated defects on manufactured
parts shows the difficulty to maintain parts in their positions during
the machining process and to estimate them during the pre-process
plan. This work presents a contribution to the development of 3D
models for the optimization of the manufacturing tolerances. An
experimental study allows the measurement of the defects of part
positioning for the determination of ε and the choice of an optimal
setup of the part. An approach of 3D tolerance based on the small
displacements method permits the determination of the
manufacturing errors upstream. A developed tool, allows an
automatic generation of the tolerance intervals along the three axes.
Abstract: Pentachlorophenol (PCP) is a polychlorinated
aromatic compound that is widespread in industrial effluents and is
considered to be a serious pollutant. Among the variety of industrial
effluents encountered, effluents from tanning industry are very
important and have a serious pollution potential. PCP is also formed
unintentionally in effluents of paper and pulp industries. It is highly
persistent in soils and is lethal to a wide variety of beneficial
microorganisms and insects, human beings and animals. The natural
processes that breakdown toxic chemicals in the environment have
become the focus of much attention to develop safe and environmentfriendly
deactivation technologies. Microbes and plants are among
the most important biological agents that remove and degrade waste
materials to enable their recycling in the environment. The present
investigation was carried out with the aim of developing a microbial
system for bioremediation of PCP polluted soils. A number of plant
species were evaluated for their ability to tolerate different
concentrations of pentachlorophenol (PCP) in the soil. The
experiment was conducted for 30 days under pot culture conditions.
The toxic effect of PCP on plants was studied by monitoring seed
germination, plant growth and biomass. As the concentration of PCP
was increased to 50 ppm, the inhibition of seed germination, plant
growth and biomass was also increased. Although PCP had a
negative effect on all plant species tested, maize and groundnut
showed the maximum tolerance to PCP. Other tolerating crops
included wheat, safflower, sunflower, and soybean. From the
rhizosphere soil of the tolerant seedlings, as many as twenty seven
PCP tolerant bacteria were isolated. From soybean, 8; sunflower, 3;
safflower 8; maize 2; groundnut and wheat, 3 each isolates were
made. They were screened for their PCP degradation potentials.
HPLC analyses of PCP degradation revealed that the isolate MAZ-2
degraded PCP completely. The isolate MAZ-1 was the next best
isolate with 90 per cent PCP degradation. These strains hold promise
to be used in the bioremediation of PCP polluted soils.