Abstract: The reluctance motor is an electric motor in which
torque is produced by the tendency of its moveable part to move to a
position where the inductance of the excited winding is maximized.
In this paper switched reluctance motors (SRMs) with two different
configurations(3-phase SRM with 4rotor poles and 6 stator poles, 4-
phase SRM with 6rotor poles and 8 stator poles) is designed by
RMxprt, and performance of them is analyzed. Efficiency and torque
of SRM for different configurations in full-load condition have been
presented. The results indicate that with correct choosing of motor
applications, maximum efficiency can be found.
Abstract: This paper presents parametric probability density
models for call holding times (CHTs) into emergency call center
based on the actual data collected for over a week in the public
Emergency Information Network (EIN) in Mongolia. When the set of
chosen candidates of Gamma distribution family is fitted to the call
holding time data, it is observed that the whole area in the CHT
empirical histogram is underestimated due to spikes of higher
probability and long tails of lower probability in the histogram.
Therefore, we provide the Gaussian parametric model of a mixture of
lognormal distributions with explicit analytical expressions for the
modeling of CHTs of PSNs. Finally, we show that the CHTs for
PSNs are fitted reasonably by a mixture of lognormal distributions
via the simulation of expectation maximization algorithm. This result
is significant as it expresses a useful mathematical tool in an explicit
manner of a mixture of lognormal distributions.
Abstract: The aim of the study was to investigate phytochemical
properties, antimicrobial activity and cytotoxicity of Aloe vera. The
phytochemical screening of the extracts of leaves of A. vera revealed
the presence of bioactive compounds such as alkaloids, tannins,
flavonoids phenolic compounds, and etc. with absence of cyanogenic
glycosides. Three different solvents such as methanol, ethanol and
Di-Methyl sulfoxide were used to screen the antimicrobial activity of
A. vera leaves against four human clinical pathogens by agar well
diffusion method. The maximum antibacterial activities were
observed in methanol extract followed by ethanol and Di-Methyl
sulfoxide. It was also found that remarkable antibacterial activities
with methanolic and ethanolic extracts of A. vera compared with the
standard antibiotic, tetracycline that was not active against E. coli
and S. boydii and supported the view that A. vera is a potent
antimicrobial agent compared with the conventional antibiotic.
Moreover, the brine shrimps (Artemia salina) toxicity test exhibited
LC50 value was 569.52 ppm. The resulting data indicated that the A.
vera plant have less toxic effects on brine shrimp. Hence, it is
signified that Aloe vera plant extract is safe to be used as an
antimicrobial agent.
Abstract: As communications systems and technology become more advanced and complex, it will be increasingly important to focus on users- individual needs. Personalization and effective user profile management will be necessary to ensure the uptake and success of new services and devices and it is therefore important to focus on the users- requirements in this area and define solutions that meet these requirements. The work on personalization and user profiles emerged from earlier ETSI work on a Universal Communications Identifier (UCI) which is a unique identifier of the user rather than a range of identifiers of the many of communication devices or services (e.g. numbers of fixed phone at home/work, mobile phones, fax and email addresses). This paper describes work on personalization including standardized information and preferences and an architectural framework providing a description of how personalization can be integrated in Next Generation Networks, together with the UCI concept.
Abstract: With constraints on data availability and for study of power system stability it is adequate to model the synchronous generator with field circuit and one equivalent damper on q-axis known as the model 1.1. This paper presents a systematic procedure for modelling and simulation of a single-machine infinite-bus power system installed with a thyristor controlled series compensator (TCSC) where the synchronous generator is represented by model 1.1, so that impact of TCSC on power system stability can be more reasonably evaluated. The model of the example power system is developed using MATLAB/SIMULINK which can be can be used for teaching the power system stability phenomena, and also for research works especially to develop generator controllers using advanced technologies. Further, the parameters of the TCSC controller are optimized using genetic algorithm. The non-linear simulation results are presented to validate the effectiveness of the proposed approach.
Abstract: Collateralized Debt Obligations are not as widely used
nowadays as they were before 2007 Subprime crisis. Nonetheless
there remains an enthralling challenge to optimize cash flows
associated with synthetic CDOs. A Gaussian-based model is used
here in which default correlation and unconditional probabilities of
default are highlighted. Then numerous simulations are performed
based on this model for different scenarios in order to evaluate the
associated cash flows given a specific number of defaults at different
periods of time. Cash flows are not solely calculated on a single
bought or sold tranche but rather on a combination of bought and
sold tranches. With some assumptions, the simplex algorithm gives
a way to find the maximum cash flow according to correlation of
defaults and maturities. The used Gaussian model is not realistic in
crisis situations. Besides present system does not handle buying or
selling a portion of a tranche but only the whole tranche. However the
work provides the investor with relevant elements on how to know
what and when to buy and sell.
Abstract: Semiconductor detector arrays are widely used in
high-temperature plasma diagnostics. They have a fast response,
which allows observation of many processes and instabilities in
tokamaks. In this paper, there are reviewed several diagnostics based
on semiconductor arrays as cameras, AXUV photodiodes (referred
often as fast “bolometers") and detectors of both soft X-rays and
visible light installed on the COMPASS tokamak recently. Fresh
results from both spring and summer campaigns in 2012 are
introduced. Examples of the utilization of the detectors are shown on
the plasma shape determination, fast calculation of the radiation
center, two-dimensional plasma radiation tomography in different
spectral ranges, observation of impurity inflow, and also on
investigation of MHD activity in the COMPASS tokamak discharges.
Abstract: In recent years asymmetric cross section aluminum
alloy stock has been finding increasing use in various industrial manufacturing areas such as general structures and automotive
components. In these areas, components are generally required to have
complex curved configuration and, as such, a bending process is required during manufacture. Undesirable deformation in bending
processes such as flattening or wrinkling can easily occur when thin-walled sections are bent. Hence, a thorough understanding of the
bending behavior of such sections is needed to prevent these undesirable deformations. In this study, the bending behavior of
asymmetric channel section was examined using finite element analysis (FEA). Typical methods of preventing undesirable
deformation, such as asymmetric laminated elastic mandrels were included in FEA model of draw bending. Additionally, axial tension
was applied to prevent wrinkling. By utilizing the FE simulations effect of restriction dies and axial tension on undesirable deformation during the process was clarified.
Abstract: The huge development of new technologies and the
apparition of open communication system more and more
sophisticated create a new challenge to protect digital content from
piracy. Digital watermarking is a recent research axis and a new
technique suggested as a solution to these problems. This technique
consists in inserting identification information (watermark) into
digital data (audio, video, image, databases...) in an invisible and
indelible manner and in such a way not to degrade original medium-s
quality. Moreover, we must be able to correctly extract the
watermark despite the deterioration of the watermarked medium (i.e
attacks). In this paper we propose a system for watermarking satellite
images. We chose to embed the watermark into frequency domain,
precisely the discrete wavelet transform (DWT). We applied our
algorithm on satellite images of Tunisian center. The experiments
show satisfying results. In addition, our algorithm showed an
important resistance facing different attacks, notably the compression
(JEPG, JPEG2000), the filtering, the histogram-s manipulation and
geometric distortions such as rotation, cropping, scaling.
Abstract: In literatures, many researches proposed various
methods to reduce PAPR (Peak to Average Power Ratio). Among
those, DSI (Dummy Sequence Insertion) is one of the most attractive
methods for WiMAX systems because it does not require side
information transmitted along with user data. However, the
conventional DSI methods find dummy sequence by performing an
iterative procedure until achieving PAPR under a desired threshold.
This causes a significant delay on finding dummy sequence and also
effects to the overall performances in WiMAX systems. In this paper,
the new method based on DSI is proposed by finding dummy
sequence without the need of iterative procedure. The fast DSI
method can reduce PAPR without either delays or required side
information. The simulation results confirm that the proposed method
is able to carry out PAPR performances as similar to the other
methods without any delays. In addition, the simulations of WiMAX
system with adaptive modulations are also investigated to realize the
use of proposed methods on various fading schemes. The results
suggest the WiMAX designers to modify a new Signal to Noise Ratio
(SNR) criteria for adaptation.
Abstract: This research aims at modeling and simulating the effects of nanofluids on cylindrical heat pipes thermal performance using the ANSYS-FLUENT CFD commercial software. The heat pipe outer wall temperature distribution, thermal resistance, liquid pressure and axial velocity in presence of suspended nano-scaled solid particle (i.e. Cu, Al2O3 and TiO2) within the fluid (water) were investigated. The effect of particle concentration and size were explored and it is concluded that the thermal performance of the heat pipe is improved when using nanofluid as the system working fluid. Additionally, it was observed that the thermal resistance of the heat pipe drops as the particle concentration level increases and particle radius decreases.
Abstract: In this study a two dimensional axisymmetric, steady state and incompressible laminar flow in a rotating single disk is numerically investigated. The finite volume method is used for solving the momentum equations. The numerical model and results
are validated by comparing it to previously reported experimental data for velocities, angles and moment coefficients. It is
demonstrated that increasing the axial distance increases the value of axial velocity and vice versa for tangential and total velocities. However, the maximum value of nondimensional radial velocity
occurs near the disk wall. It is also found that with increase rotational Reynolds number, moment coefficient decreases.
Abstract: The Random Coefficient Dynamic Regression (RCDR)
model is to developed from Random Coefficient Autoregressive
(RCA) model and Autoregressive (AR) model. The RCDR model
is considered by adding exogenous variables to RCA model. In this
paper, the concept of the Maximum Likelihood (ML) method is used
to estimate the parameter of RCDR(1,1) model. Simulation results
have shown the AIC and BIC criterion to compare the performance of
the the RCDR(1,1) model. The variables as the stationary and weakly
stationary data are good estimates where the exogenous variables
are weakly stationary. However, the model selection indicated that
variables are nonstationarity data based on the stationary data of the
exogenous variables.
Abstract: High Speed PM Generators driven by micro-turbines
are widely used in Smart Grid System. So, this paper proposes
comparative study among six classical, optimized and genetic
analytical design cases for 400 kW output power at tip speed 200
m/s. These six design trials of High Speed Permanent Magnet
Synchronous Generators (HSPMSGs) are: Classical Sizing;
Unconstrained optimization for total losses and its minimization;
Constrained optimized total mass with bounded constraints are
introduced in the problem formulation. Then a genetic algorithm is
formulated for obtaining maximum efficiency and minimizing
machine size. In the second genetic problem formulation, we attempt
to obtain minimum mass, the machine sizing that is constrained by
the non-linear constraint function of machine losses. Finally, an
optimum torque per ampere genetic sizing is predicted. All results are
simulated with MATLAB, Optimization Toolbox and its Genetic
Algorithm. Finally, six analytical design examples comparisons are
introduced with study of machines waveforms, THD and rotor losses.
Abstract: The analytical solution of functionally graded
piezoelectric hollow cylinder which is under radial electric potential
and non-axisymmetric thermo-mechanical loads, are presented in this
paper. Using complex Fourier series and estimation of power law for
variations of material characterizations through the thickness, the
electro thermo mechanical behavior of the FGPM cylinder is
obtained. The stress and displacement distributions and the effect of
electric potential field on the cylinder behavior are also presented and
some applicable results are offered at the end of the paper.
Abstract: Support Vector Machine (SVM) is a recent class of statistical classification and regression techniques playing an increasing role in applications to detection problems in various engineering problems, notably in statistical signal processing, pattern recognition, image analysis, and communication systems. In this paper, SVM is applied to an infrared (IR) binary communication system with different types of channel models including Ricean multipath fading and partially developed scattering channel with additive white Gaussian noise (AWGN) at the receiver. The structure and performance of SVM in terms of the bit error rate (BER) metric is derived and simulated for these channel stochastic models and the computational complexity of the implementation, in terms of average computational time per bit, is also presented. The performance of SVM is then compared to classical binary signal maximum likelihood detection using a matched filter driven by On-Off keying (OOK) modulation. We found that the performance of SVM is superior to that of the traditional optimal detection schemes used in statistical communication, especially for very low signal-to-noise ratio (SNR) ranges. For large SNR, the performance of the SVM is similar to that of the classical detectors. The implication of these results is that SVM can prove very beneficial to IR communication systems that notoriously suffer from low SNR at the cost of increased computational complexity.
Abstract: This paper introduces and studies new indexing techniques for content-based queries in images databases. Indexing is the key to providing sophisticated, accurate and fast searches for queries in image data. This research describes a new indexing approach, which depends on linear modeling of signals, using bases for modeling. A basis is a set of chosen images, and modeling an image is a least-squares approximation of the image as a linear combination of the basis images. The coefficients of the basis images are taken together to serve as index for that image. The paper describes the implementation of the indexing scheme, and presents the findings of our extensive evaluation that was conducted to optimize (1) the choice of the basis matrix (B), and (2) the size of the index A (N). Furthermore, we compare the performance of our indexing scheme with other schemes. Our results show that our scheme has significantly higher performance.
Abstract: An empirical linearly-hyperbolic approximation of the I - V characteristic of a solar cell is presented. This approximation is based on hyperbolic dependence of a current of p-n junctions on voltage for large currents. Such empirical approximation is compared with the early proposed formal linearly-hyperbolic approximation of a solar cell. The expressions defining laws of change of parameters of formal approximation at change of a photo current of family of characteristics are received. It allows simplifying a finding of parameters of approximation on actual curves, to specify their values. Analytical calculation of load regime for linearly - hyperbolic model leads to quadratic equation. Also, this model allows to define soundly a deviation from the maximum power regime and to compare efficiency of regimes of solar cells with different parameters.
Abstract: The habitat where the present study has been carried
out is productive in relation to nutrient quality and they may perform
several useful functions, but are also threatened for their existence.
Hence, the proposed work, will add much new information about
biodiversity of macrophytes in drains and their embankment. All the
species were identified with their different stages of growth which
encountered on the three selected sites (I, II and III). The number of
species occurring at each site is grouped seasonally, i.e. summer,
rainy and winter season and the species were further recorded for the
study of phytosociology. Phytosociological characters such as
frequency, density and abundance were influenced by the climatic,
anthropogenic and biotic stresses prevailing at the three study sites.
All the species present at the study sites have shown maximum
values of frequency, density and abundance in rainy season in
comparison to that of summer and winter seasons.
Abstract: The objective of this work is to investigate the
turbulent reacting flow in a three dimensional combustor with
emphasis on the effect of inlet swirl flow through a numerical
simulation. Flow field is analyzed using the SIMPLE method which is
known as stable as well as accurate in the combustion modeling, and
the finite volume method is adopted in solving the radiative transfer
equation. In this work, the thermal and flow characteristics in a three
dimensional combustor by changing parameters such as equivalence
ratio and inlet swirl angle have investigated. As the equivalence ratio
increases, which means that more fuel is supplied due to a larger inlet
fuel velocity, the flame temperature increases and the location of
maximum temperature has moved towards downstream. In the mean
while, the existence of inlet swirl velocity makes the fuel and
combustion air more completely mixed and burnt in short distance.
Therefore, the locations of the maximum reaction rate and temperature
were shifted to forward direction compared with the case of no swirl.