Abstract: Shortfall of electrical energy in Pakistan is a challenge
adversely affecting its industrial output and social growth. As
elsewhere, Pakistan derives its electrical energy from a number of
conventional sources. The exhaustion of petroleum and conventional
resources, the rising costs coupled with extremely adverse climatic
effects are taking its toll especially on the under-developed countries
like Pakistan. As alternate, renewable energy sources like hydropower,
solar, wind, even bio-energy and a mix of some or all of them
could provide a credible alternative to the conventional energy
resources that would not only be cleaner but sustainable as well. As a
model, solar energy-based power grid for the near future has been
attempted to offset the energy shortfalls as a mix with our existing
sustainable natural energy resources. An assessment of solar energy
potential for electricity generation is being presented for fulfilling the
energy demands with higher level of reliability and sustainability.
This model is based on the premise that solar energy potential of
Pakistan is not only reliable but also sustainable. This research
estimates the present & future approaching renewable energy
resource specially the impact of solar energy based power grid for
mitigating energy shortage in Pakistan.
Abstract: An efficient and green method for oxidation of thiols
to the corresponding disulfides is reported using ionic liquid
[HSO3N(C2H4OSO3H)3] in the presence of free nano-Fe2O3 at 60°C.
Ionic liquid is selective oxidant for S-S Coupling variety aliphatic
and aromatic of thiols to corresponding disulfide in the presence of
free nano-Fe2O3 as recoverable catalyst. Reaction has been performed
in methanol as an inexpensive solvent. This reaction is clean and easy
work-up with no side reaction.
Abstract: Wet scrubbers have found widespread use in cleaning
contaminated gas streams because of their ability to remove
particulates and based on the applications of scrubbing of marine
engine exhaust gases by spraying sea-water. In order to examine the
flow characteristics inside the scrubber, the model is designated with
flow properties of hot air and water sprayer. The flow dynamics of
evaporation of hot air by the injection of water droplets is the key
factor considered in this paper. The flow behavior inside the scrubber
was investigated from the previous works and to sum up the
evaporation rate with respect to the concentration of water droplets are
predicted to bring out the competent modelling. The numerical
analysis using CFD facilitates in understanding the problem better and
empathies the behavior of the model over its entire operating envelope.
Abstract: Software Architecture is the basic structure of
software that states the development and advancement of a software
system. Software architecture is also considered as a significant tool
for the construction of high quality software systems. A clean design
leads to the control, value and beauty of software resulting in its
longer life while a bad design is the cause of architectural erosion
where a software evolution completely fails. This paper discusses the
occurrence of software architecture erosion and presents a set of
methods for the detection, declaration and prevention of architecture
erosion. The causes and symptoms of architecture erosion are
observed with the examples of prescriptive and descriptive
architectures and the practices used to stop this erosion are also
discussed by considering different types of software erosion and their
affects. Consequently finding and devising the most suitable
approach for fighting software architecture erosion and in some way
reducing its affect is evaluated and tested on different scenarios.
Abstract: The paper involves a chain of activities from
synthesis, establishment of the methodology for characterization and
testing of novel protective materials through the pilot production and
application on model supports.
It summarizes the results regarding the development of the pilot
production protocol for newly developed self-cleaning materials. The
optimization of the production parameters was completed in order to
improve the most important functional properties (mineralogy
characteristics, particle size, self-cleaning properties and
photocatalytic activity) of the newly designed nanocomposite
material.
Abstract: Reburning is a useful technology in reducing nitric
oxide through injection of a secondary hydrocarbon fuel. In this paper,
an experimental study has been conducted to evaluate the effect of fuel
lean reburning on NOx/CO reduction in LNG flame. Experiments
were performed in flames stabilized by a co-flow swirl burner, which
was mounted at the bottom of the furnace. Tests were conducted using
LNG gas as the reburn fuel as well as the main fuel. The effects of
reburn fuel fraction and injection manner of the reburn fuel were
studied when the fuel lean reburning system was applied. The paper
reports data on flue gas emissions and temperature distribution in the
furnace for a wide range of experimental conditions. At steady state,
temperature distribution and emission formation in the furnace have
been measured and compared. This paper makes clear that in order to
decrease both NOx and CO concentrations in the exhaust when the
pulsated fuel lean reburning system was adapted, it is important that
the control of some factors such as frequency and duty ratio. Also it
shows the fuel lean reburning is also effective method to reduce NOx
as much as reburning.
Abstract: This paper aims to represent the commercial activity
of a city taking as source data the social network Foursquare. The
city of Murcia is selected as case study, and the location-based
social network Foursquare is the main source of information. After
carrying out a reorganisation of the user-generated data extracted
from Foursquare, it is possible to graphically display on a map the
various city spaces and venues especially those related to commercial,
food and entertainment sector businesses. The obtained visualisation
provides information about activity patterns in the city of Murcia
according to the people‘s interests and preferences and, moreover,
interesting facts about certain characteristics of the town itself.
Abstract: A cleaner production project was implemented in a
bakery. The project is based on the substitution of the best available
technique for an obsolete leaven production technology. The new
technology enables production of durable, high-quality leavens.
Moreover, 25% of flour as the original raw material can be replaced
by pastry from the previous day production which has not been sold.
That pastry was previously disposed in a waste incineration plant.
Besides the environmental benefits resulting from less waste, lower
consumption of energy, reduction of sewage waters quantity and
floury dustiness there are also significant economic benefits. Payback
period of investment was calculated with help of static method of
financial analysis about 2.6 years, using dynamic method 3.5 years
and an internal rate of return more than 29%. The supposed annual
average profit after taxationin the second year of operation was
incompliance with the real profit.
Abstract: The Lean Environmental Management Integration
System (LEMIS) framework development is integration between lean
core element and ISO 14001. The curiosity on the relationship
between continuous improvement and sustainability of lean
implementation has influenced this study toward LEMIS.
Characteristic of ISO 14001 standard clauses and core elements of
lean principles are explored from past studies and literature reviews.
Survey was carried out on ISO 14001 certified companies to examine
continual improvement by implementing the ISO 14001 standard.
The study found that there is a significant and positive relationship
between Lean Principles: value, value stream, flow, pull and
perfection with the ISO 14001 requirements. LEMIS is significant to
support the continuous improvement and sustainability. The
integration system can be implemented to any manufacturing
company. It gives awareness on the importance on why organizations
need to sustain its environmental management system. In the
meantime, the lean principle can be adapted in order to streamline
daily activities of the company. Throughout the study, it had proven
that there is no sacrifice or trade-off between lean principles with ISO
14001 requirements. The framework developed in the study can be
further simplified in the future, especially the method of crossing
each sub requirements of ISO 14001 standard with the core elements
of Lean principles in this study.
Abstract: This review summarizes the potential of starch
agroindustrial residues as substrate for biohydrogen production.
Types of potential starch agroindustrial residues, recent developments
and bio-processing conditions for biohydrogen production will be
discussed. Biohydrogen is a clean energy source with great potential
to be an alternative fuel, because it releases energy explosively in
heat engines or generates electricity in fuel cells producing water as
only by-product. Anaerobic hydrogen fermentation or dark
fermentation seems to be more favorable, since hydrogen is yielded
at high rates and various organic waste enriched with carbohydrates
as substrate result in low cost for hydrogen production. Abundant
biomass from various industries could be source for biohydrogen
production where combination of waste treatment and energy
production would be an advantage. Carbohydrate-rich nitrogendeficient
solid wastes such as starch residues can be used for
hydrogen production by using suitable bioprocess technologies.
Alternatively, converting biomass into gaseous fuels, such as
biohydrogen is possibly the most efficient way to use these
agroindustrial residues.
Abstract: Electricity is recognized as fundamental to
industrialization and improving the quality of life of the people.
Harnessing the immense untapped hydropower potential in Tripura
region opens avenues for growth and provides an opportunity to
improve the well-being of the people of the region, while making
substantial contribution to the national economy. Gumti hydro power
plant generates power to mitigate the crisis of power in Tripura,
India. The first unit of hydro power plant (5MW) was commissioned
in June 1976 & another two units of 5 MW was commissioned
simultaneously. But out of 15MW capacity at present only 8MW-
9MW power is produced from Gumti hydro power plant during rainy
season. But during lean season the production reduces to 0.5MW due
to shortage of water. Now, it is essential to implement some
mitigation measures so that the further atrocities can be prevented
and originality will be possible to restore. The decision making
ability of the Analytic Hierarchy Process (AHP) and Concordance
Analysis Techniques (CAT) are utilized to identify the better decision
or solution to the present problem. Some related attributes are
identified by the method of surveying within the experts and the
available reports and literatures. Similar criteria are removed and
ultimately seven relevant ones are identified. All the attributes are
compared with each other and rated accordingly to their importance
over the other with the help of Pair wise Comparison Matrix. In the
present investigation different mitigation measures are identified and
compared to find the best suitable alternative which can solve the
present uncertainties involving the existence of the Gumti Hydro
Power Plant.
Abstract: In new energy development, wind power has boomed.
It is due to the proliferation of wind parks and their operation in
supplying the national electric grid with low cost and clean resources.
Hence, there is an increased need to establish a proactive
maintenance for wind turbine machines based on remote control and
monitoring. That is necessary with a real-time wireless connection in
offshore or inaccessible locations while the wired method has many
flaws. The objective of this strategy is to prolong wind turbine
lifetime and to increase productivity. The hardware of a remote
control and monitoring system for wind turbine parks is designed. It
takes advantage of GPRS or Wi-Max wireless module to collect data
measurements from different wind machine sensors through IP based
multi-hop communication. Computer simulations with Proteus ISIS
and OPNET software tools have been conducted to evaluate the
performance of the studied system. Study findings show that the
designed device is suitable for application in a wind park.
Abstract: The purpose of this project is to carry out an analysis
and determine the profile of actual lean manufacturing processes in
the Metropolitan Area of Bucaramanga. Through the analysis of
qualitative and quantitative variables it was possible to establish how
these manufacturers develop production practices that ensure their
competitiveness and productivity in the market.
In this study, a random sample of metallurgic and wrought iron
companies was applied, following which a quantitative focus and
analysis was used to formulate a qualitative methodology for
measuring the level of lean manufacturing procedures in the industry.
A qualitative evaluation was also carried out through a multivariate
analysis using the Numerical Taxonomy System (NTSYS) program
which should allow for the determination of Lean Manufacturing
profiles.
Through the results it was possible to observe how the companies
in the sector are doing with respect to Lean Manufacturing Practices,
as well as identify the level of management that these companies
practice with respect to this topic. In addition, it was possible to
ascertain that there is no one dominant profile in the sector when it
comes to Lean Manufacturing.
It was established that the companies in the metallurgic and
wrought iron industry show low levels of Lean Manufacturing
implementation. Each one carries out diverse actions that are
insufficient to consolidate a sectoral strategy for developing a
competitive advantage which enables them to tie together a
production strategy.
Abstract: Web-based Cognitive Writing Instruction (WeCWI) is
a hybrid e-framework for the development of a web-based instruction
(WBI), which contributes towards instructional design and language
development. WeCWI divides its contribution in instructional design
into macro and micro perspectives. In macro perspective, being a 21st
century educator by disseminating knowledge and sharing ideas with
the in-class and global learners is initiated. By leveraging the virtue
of technology, WeCWI aims to transform an educator into an
aggregator, curator, publisher, social networker and ultimately, a
web-based instructor. Since the most notable contribution of
integrating technology is being a tool of teaching as well as a
stimulus for learning, WeCWI focuses on the use of contemporary
web tools based on the multiple roles played by the 21st century
educator. The micro perspective in instructional design draws
attention to the pedagogical approaches focusing on three main
aspects: reading, discussion, and writing. With the effective use of
pedagogical approaches through free reading and enterprises,
technology adds new dimensions and expands the boundaries of
learning capacity. Lastly, WeCWI also imparts the fundamental
theories and models for web-based instructors’ awareness such as
interactionist theory, cognitive information processing (CIP) theory,
computer-mediated communication (CMC), e-learning interactionalbased
model, inquiry models, sensory mind model, and leaning styles
model.
Abstract: This paper is about method to produce a stable and
accurate constant output pulse width regardless of the amplitude,
period and pulse width variation of the input signal source. The pulse
generated is usually being used in numerous applications as the
reference input source to other circuits in the system. Therefore, it is
crucial to produce a clean and constant pulse width to make sure the
system is working accurately as expected.
Abstract: This paper deals with the issue of biomass and sorted
municipal waste gasification and cogeneration using hot-air turbo-set.
It brings description of designed pilot plant with electrical output 80
kWe. The generated gas is burned in secondary combustion chamber
located beyond the gas generator. Flue gas flows through the heat
exchanger where the compressed air is heated and consequently
brought to a micro turbine. Except description, this paper brings our
basic experiences from operating of pilot plant (operating parameters,
contributions, problems during operating, etc.). The principal
advantage of the given cycle is the fact that there is no contact
between the generated gas and the turbine. So there is no need for
costly and complicated gas cleaning which is the main source of
operating problems in direct use in combustion engines because the
content of impurities in the gas causes operation problems to the units
due to clogging and tarring of working surfaces of engines and
turbines, which may lead as far as serious damage to the equipment
under operation. Another merit is the compact container package
making installation of the facility easier or making it relatively more
mobile. We imagine, this solution of cogeneration from biomass or
waste can be suitable for small industrial or communal applications,
for low output cogeneration.
Abstract: This research paper aims to identify, analyze and rank
factors affecting labor productivity in Spain with respect to their
relative importance. Using a selected set of 35 factors, a structured
questionnaire survey was utilized as the method to collect data from
companies. Target population is comprised by a random
representative sample of practitioners related with the Spanish
construction industry. Findings reveal the top five ranked factors are
as follows: (1) shortage or late supply of materials; (2) clarity of the
drawings and project documents; (3) clear and daily task assignment;
(4) tools or equipment shortages; (5) level of skill and experience of
laborers. Additionally, this research also pretends to provide simple
and comprehensive recommendations so that they could be
implemented by construction managers for an effective management
of construction labor forces.
Abstract: The most important part of modern lean low NOx combustors is a premixer where swirlers are often used for intensification of mixing processes and further formation of required flow pattern in combustor liner. Swirling flow leads to formation of complex eddy structures causing flow perturbations. It is able to cause combustion instability. Therefore, at design phase, it is necessary to pay great attention to aerodynamics of premixers. Analysis based on unsteady CFD modeling of swirling flow in production combustor swirler showed presence of large number of different eddy structures that can be conditionally divided into three types relative to its location of origin and a propagation path. Further, features of each eddy type were subsequently defined. Comparison of calculated and experimental pressure fluctuations spectrums verified correctness of computations.
Abstract: In this paper we make a temperature investigations in
two type of superposed crimped connections using experimental
determinations. All the samples use 8 copper wire 7.1 x 3 mm2
crimped by two methods: the first method uses one crimp indents and
the second is a proposed method with two crimp indents. The ferrule
is a parallel one. We study the influence of number and position of
crimp indents. The samples are heated in A.C. current at different
current values until steady state heating regime. After obtaining of
temperature values, we compare them and present the conclusion.
Abstract: A generalized vortex lattice method for complex
lifting surfaces with flap and aileron deflection is formulated. The
method is not restricted by the linearized theory assumption and
accounts for all standard geometric lifting surface parameters:
camber, taper, sweep, washout, dihedral, in addition to flap and
aileron deflection. Thickness is not accounted for since the physical
lifting body is replaced by a lattice of panels located on the mean
camber surface. This panel lattice setup and the treatment of different
wake geometries is what distinguish the present work form the
overwhelming majority of previous solutions based on the vortex
lattice method. A MATLAB code implementing the proposed
formulation is developed and validated by comparing our results to
existing experimental and numerical ones and good agreement is
demonstrated. It is then used to study the accuracy of the widely used
classical vortex-lattice method. It is shown that the classical approach
gives good agreement in the clean configuration but is off by as much
as 30% when a flap or aileron deflection of 30° is imposed. This
discrepancy is mainly due the linearized theory assumption
associated with the conventional method. A comparison of the effect
of four different wake geometries on the values of aerodynamic
coefficients was also carried out and it is found that the choice of the
wake shape had very little effect on the results.