Abstract: Foundation differential settlement and supported
structure tilting are an occasionally occurred engineering problem.
This may be caused by overloading, changes in ground soil properties
or unsupported nearby excavations. Engineering thinking points
directly toward the logic solution for such problem by uplifting the
settled side. This can be achieved with deep foundation elements
such as micro-piles and macro-piles™, jacked piers, and helical piers,
jet grouted mortar columns, compaction grout columns, cement
grouting or with chemical grouting, or traditional pit underpinning
with concrete and mortar. Although, some of these techniques offer
economic, fast and low noise solutions, many of them are quite the
contrary. For tilted structures, with the limited inclination, it may be much
easier to cause a balancing settlement on the less-settlement side
which shall be done carefully in a proper rate. This principal has been
applied in Leaning Tower of Pisa stabilization with soil extraction
from the ground surface. In this research, the authors attempt to
introduce a new solution with a different point of view. So, the
micro-tunneling technique is presented in here as an intended ground
deformation cause. In general, micro-tunneling is expected to induce
limited ground deformations. Thus, the researchers propose to apply
the technique to form small size ground unsupported holes to produce
the target deformations. This shall be done in four phases: 1.
Application of one or more micro-tunnels, regarding the existing
differential settlement value, under the raised side of the tilted
structure. 2. For each individual tunnel, the lining shall be pulled out
from both sides (from jacking and receiving shafts) in the slow rate.
3. If required, according to calculations and site records, an additional
surface load can be applied on the raised foundation side. 4. Finally, a
strengthening soil grouting shall be applied for stabilization after
adjustment. A finite element based numerical model is presented to simulate
the proposed construction phases for different tunneling positions and
tunnels group. For each case, the surface settlements are calculated
and induced plasticity points are checked. These results show the
impact of the suggested procedure on the tilted structure and its
feasibility. Comparing results also show the importance of the
position selection and tunnels group gradual effect. Thus, a new
engineering solution is presented to one of the structural and
geotechnical engineering challenges.
Abstract: This study aims at improving the urban hydrological
cycle of the Orléans agglomeration (France) and understanding the
relationship between physical and chemical parameters of urban
surface runoff and the hydrological conditions. In particular water
quality parameters such as pH, conductivity, total dissolved solids,
major dissolved cations and anions, and chemical and biological
oxygen demands were monitored for three types of urban water
discharges (wastewater treatment plant output (WWTP), storm
overflow and stormwater outfall) under two hydrologic scenarios (dry
and wet weather). The first results were obtained over a period of five
months. Each investigated (Ormes, l’Egoutier and La Corne) outfall
represents an urban runoff source that receives water from runoff
roads, gutters, the irrigation of gardens and other sources of flow over
the Earth’s surface that drains in its catchments and carries it to the
Loire River. In wet weather conditions there is rain water runoff and
an additional input from the roof gutters that have entered the
stormwater system during rainfall. For the comparison the results La
Chilesse is a storm overflow that was selected in our study as a
potential source of waste water which is located before the (WWTP). The comparison of the physical-chemical parameters (total
dissolved solids, turbidity, pH, conductivity, dissolved organic
carbon (DOC), concentration of major cations and anions) together
with the chemical oxygen demand (COD) and biological oxygen
demand (BOD) helped to characterize sources of runoff waters in the
different watersheds. It also helped to highlight the infiltration of
wastewater in some stormwater systems that reject directly in the
Loire River. The values of the conductivity measured in the outflow
of Ormes were always higher than those measured in the other two
outlets. The results showed a temporal variation for the Ormes outfall
of conductivity from 1465 μS cm-1 in the dry weather flow to 650 μS
cm-1 in the wet weather flow and also a spatial variation in the wet
weather flow from 650 μS cm-1 in the Ormes outfall to 281 μS cm-1
in L’Egouttier outfall. The ultimate BOD (BOD28) showed a
significant decrease in La Corne outfall from 181 mg L-1 in the wet
weather flow to 95 mg L-1 in the dry weather flow because of the
nutrient load that was transported by the runoff.
Abstract: The market competition is moving from the single
firm to the whole supply chain because of increasing competition and
growing need for operational efficiencies and customer orientation.
Supply chain management allows companies to look beyond their
organizational boundaries to develop and leverage resources and
capabilities of their supply chain partners. This creates competitive
advantages in the marketplace and because of this SCM has acquired
strategic importance. Lean Approach is a management strategy that focuses on reducing
every type of waste present in an organization. This approach is
becoming more and more popular among supply chain managers. The supply chain application of lean approach is not frequent. In
particular, it is not well studied which are the impacts of lean
approach principles in a supply chain context. In literature there are
only few studies aimed at understanding the qualitative impact of the
lean approach in supply chains. Therefore, the goal of this research
work is to study the impacts of lean principles implementation along
a supply chain. To achieve this, a simulation model of a threeechelon
multi-product supply chain has been built. Kanban system (and several priority policies) and setup time
reduction degrees are implemented in the lean-configured supply
chain to apply pull and lot-sizing decrease principles respectively. To
evaluate the benefits of lean approach, lean supply chain is compared
with an EOQ-configured supply chain. The simulation results show
that Kanban system and setup-time reduction improve inventory
stock level. They also show that logistics efforts are affected to lean
implementation degree. The paper concludes describing
performances of lean supply chain in different contexts.
Abstract: Construction industry plays a vital role in the
economy of the world. However, due to high uncertainty and
variability in the industry, its performance is not as efficient in terms
of quality, lead times, productivity and costs as of other industries.
Moreover, there are continuous conflicts among the different actors
in the construction supply chains in terms of profit sharing. Previous
studies suggested partnership as an important approach to promote
cooperation among the different actors in the construction supply
chains and thereby it improves the overall performance. Construction
practitioners tried to focus on partnership which can enhance the
performance of construction supply chains but they are not fully
aware of different approaches and techniques for improving
partnership. In this research, a systematic review on partnership in
relation to construction supply chains is carried out to understand
different elements influencing the partnership. The research
development of this domain is analyzed by reviewing selected
articles published from 1996 to 2015. Based on the papers, three
major elements influencing partnership in construction supply chains
are identified: ‘Lean approach’, ‘Relationship building’ and ‘E-commerce
applications’. This study analyses the contributions in the
areas within each element and provides suggestions for future
developments of partnership in construction supply chains.
Abstract: This paper introduces the concept and principle of data
cleaning, analyzes the types and causes of dirty data, and proposes
several key steps of typical cleaning process, puts forward a well
scalability and versatility data cleaning framework, in view of data
with attribute dependency relation, designs several of violation data
discovery algorithms by formal formula, which can obtain inconsistent
data to all target columns with condition attribute dependent no matter
data is structured (SQL) or unstructured (NoSql), and gives 6 data
cleaning methods based on these algorithms.
Abstract: This study was undertaken at four different sites
(north polluted, south polluted, south healthy and north healthy) in
Tehran, in order to examine whether there was a relationship between
publicly available air quality data and the public’s perception of air
quality and to suggest some guidelines for reducing air pollution. A
total of 200 people were accidentally filled out the research
questionnaires at mentioned sites and air quality data were obtained
simultaneously from the Air Quality Control Department. Data was
analyzed in Excel and SPSS software’s. Clean air and job security
were of great importance to people comparing to other pleasant
aspect of life. Also air pollution and serious diseases were the most
important of people concerns. Street monitors and news paper
services on air quality were little used by the public as a means of
obtaining information on air pollution. Using public transportation
and avoiding inevitable journeys are the most important ways for
reducing air pollution. The results reveal that the public’s perception
of air quality is not a reliable indicator of the actual levels of air
pollution.
Abstract: Ultraviolet photocatalytic oxidation (UV-PCO)
technology has been recommended as a green approach to health
indoor environment when it is integrated into mechanical ventilation
systems for inorganic and organic compounds removal as well as
energy saving due to less outdoor air intakes. Although much research
has been devoted to UV-PCO, limited information is available on the
UV-PCO behavior tested by the mixtures in literature. This project
investigated UV-PCO performance and by-product generation using a
single and a mixture of acetone and MEK at 100 ppb each in a
single-pass duct system in an effort to obtain knowledge associated
with competitive photochemical reactions involved in. The
experiments were performed at 20 % RH, 22 °C, and a gas flow rate of
128 m3/h (75 cfm). Results show that acetone and MEK mutually
reduced each other’s PCO removal efficiency, particularly negative
removal efficiency for acetone. These findings were different from
previous observation of facilitatory effects on the adsorption of
acetone and MEK on photocatalyst surfaces.
Abstract: The application of cold Radio-Frequency (RF) plasma
in the conservation of cultural heritage became important in the last
decades due to the positive results obtained in decontamination
treatments. This paper presents an equipment especially designed for cold RF
plasma application on paper documents, developed within a research
project. The equipment consists in two modules: the first one is
designed for decontamination and cleaning treatments of any type of
paper supports, while the second one can be used for coating friable
papers with adequate polymers, for protection purposes. All these
operations are carried out in cold radio-frequency plasma, working in
gaseous nitrogen, at low pressure. In order to optimize the equipment parameters ancient paper
samples infested with microorganisms have been treated in nitrogen
plasma and the decontamination effects, as well as changes in surface
properties (color, pH) were assessed. The microbiological analysis
revealed complete decontamination at 6 minutes treatment duration;
only minor modifications of the surface pH were found and the
colorimetric analysis showed a slight yellowing of the support.
Abstract: Web mining is to discover and extract useful
Information. Different users may have different search goals when
they search by giving queries and submitting it to a search engine.
The inference and analysis of user search goals can be very useful for
providing an experience result for a user search query. In this project,
we propose a novel approach to infer user search goals by analyzing
search web logs. First, we propose a novel approach to infer user
search goals by analyzing search engine query logs, the feedback
sessions are constructed from user click-through logs and it
efficiently reflect the information needed for users. Second we
propose a preprocessing technique to clean the unnecessary data’s
from web log file (feedback session). Third we propose a technique
to generate pseudo-documents to representation of feedback sessions
for clustering. Finally we implement k-medoids clustering algorithm
to discover different user search goals and to provide a more optimal
result for a search query based on feedback sessions for the user.
Abstract: Sewer deposits have been identified as a major cause
of dysfunctions in combined sewer systems regarding sewer
management, which induces different negative consequents resulting
in poor hydraulic conveyance, environmental damages as well as
worker’s health. In order to overcome the problematics of
sedimentation, flushing has been considered as the most operative
and cost-effective way to minimize the sediments impacts and
prevent such challenges. Flushing, by prompting turbulent wave
effects, can modify the bed form depending on the hydraulic
properties and geometrical characteristics of the conduit. So far, the
dynamics of the bed-load during high-flow events in combined sewer
systems as a complex environment is not well understood, mostly due
to lack of measuring devices capable to work in the “hostile” in
combined sewer system correctly. In this regards, a one-episode
flushing issue from an opening gate valve with weir function was
carried out in a trunk sewer in Paris to understand its cleansing
efficiency on the sediments (thickness: 0-30 cm). During more than
1h of flushing within 5 m distance in downstream of this flushing
device, a maximum flowrate and a maximum level of water have
been recorded at 5 m in downstream of the gate as 4.1 m3/s and 2.1
m respectively. This paper is aimed to evaluate the efficiency of this
type of gate for around 1.1 km (from the point -50 m to +1050 m in
downstream from the gate) by (i) determining bed grain-size
distribution and sediments evolution through the sewer channel, as
well as their organic matter content, and (ii) identifying sections that
exhibit more changes in their texture after the flush. For the first one,
two series of sampling were taken from the sewer length and then
analyzed in laboratory, one before flushing and second after, at same
points among the sewer channel. Hence, a non-intrusive sampling
instrument has undertaken to extract the sediments smaller than the
fine gravels. The comparison between sediments texture after the
flush operation and the initial state, revealed the most modified zones
by the flush effect, regarding the sewer invert slope and hydraulic
parameters in the zone up to 400 m from the gate. At this distance,
despite the increase of sediment grain-size rages, D50 (median grainsize)
varies between 0.6 mm and 1.1 mm compared to 0.8 mm and 10
mm before and after flushing, respectively. Overall, regarding the
sewer channel invert slope, results indicate that grains smaller than
sands (< 2 mm) are more transported to downstream along about 400
m from the gate: in average 69% before against 38% after the flush
with more dispersion of grain-sizes distributions. Furthermore, high
effect of the channel bed irregularities on the bed material evolution
has been observed after the flush.
Abstract: There is currently a gap in the technology covering the
rapid establishment of control after a reconfiguration in a
Reconfigurable Manufacturing System. This gap involves the
detection of the factory floor state and the communication link
between the factory floor and the high-level software. In this paper, a
thin, hardware-supported Middleware Management System (MMS) is
proposed and its design and implementation are discussed. The
research found that a cost-effective localization technique can be
combined with intelligent software to speed up the ramp-up of a
reconfigured system. The MMS makes the process more intelligent,
more efficient and less time-consuming, thus supporting the
industrial implementation of the RMS paradigm.
Abstract: This paper is focused on the reference current
calculation in the compensation mode of the active DC traction
substations. The so-called p-q theory of the instantaneous reactive
power is used as theoretical foundation. The compensation goal of
total compensation is taken into consideration for the operation under
both sinusoidal and nonsinusoidal voltage conditions, through the
two objectives of unity power factor and perfect harmonic
cancelation. Four blocks of reference current generation implement
the conceived algorithms and they are included in a specific Simulink
library, which is useful in a DSP dSPACE-based platform working
under Matlab/Simulink. The simulation results validate the
correctness of the implementation and fulfillment of the
compensation tasks.
Abstract: The notion of power and gender domination is one of
the inseparable aspects of themes in postmodern literature. The
reason of its importance has been discussed frequently since the rise
of Michel Foucault and his insight into the circulation of power and
the transgression of forces. Language and society operate as the basic
grounds for the study, as all human beings are bound to the set of
rules and norms which shape them in the acceptable way in the
macrocosm. How different genders in different positions behave and
show reactions to the provocation of social forces and superiority of
one another is of great interest to writers and literary critics. Mamet’s
works are noticeable for their controversial but timely themes which
illustrate human conflicts with the society and greed for power. Many
critics like Christopher Bigsby and Harold Bloom have discussed
Mamet and his ideas in recent years. This paper is the study of
Oleanna, Mamet’s masterpiece about the teacher-student relationship
and the circulation of power between a man and woman. He shows
the very breakable boundaries in the domination of a gender and the
downfall of speech as the consequence of transgression and freedom.
The failure of the language the teacher uses and the abuse of his own
words by a student who seeks superiority and knowledge are the
main subjects of the discussion. Supported by the ideas of Foucault,
the language Mamet uses to present his characters becomes the
fundamental premise in this study. As a result, language becomes
both the means of achievement and downfall.
Abstract: Nowadays, the use of renewable energy sources has been increasingly great because of the cost increase and public demand for clean energy sources. One of the fastest growing sources is wind energy. In this paper, Wind Diesel Hybrid System (WDHS) comprising a Diesel Generator (DG), a Wind Turbine Generator (WTG), the Consumer Load, a Battery-based Energy Storage System (BESS), and a Dump Load (DL) is used. Voltage is controlled by Diesel Generator; the frequency is controlled by BESS and DL. The BESS elimination is an efficient way to reduce maintenance cost and increase the dynamic response. Simulation results with graphs for the frequency of Power System, active power, and the battery power are presented for load changes. The controlling parameters are optimized by using Imperialist Competitive Algorithm (ICA). The simulation results for the BESS/no BESS cases are compared. Results show that in no BESS case, the frequency control is more optimal than the BESS case by using ICA.
Abstract: A dip-coating process has been used to form an
asymmetric silica membrane with improved membrane performance
and reproducibility. First, we deposited repeatedly silica on top of a
commercial alumina membrane support to improve its structural
make up. The membrane is further processed under clean room
conditions to avoid dust impurity and subsequent drying in an oven
for high thermal, chemical and physical stability. The resulting
asymmetric membrane exhibits a gradual change in the membrane
layer thickness. Compared to the support, the dual-layer process
improves the gas flow rates. For the scientific applications for natural
gas purification, CO2, CH4 and H2 gas flow rates were. In addition,
the membrane selectively separated hydrogen.
Abstract: Exploration and exploitation capabilities are both
important within Operations as means for improvement when
managed separately, and for establishing dynamic improvement
capabilities when combined in balance. However, it is unclear what
exploration and exploitation capabilities imply in improvement and
development work within an Operations context. So, in order to
better understand how to develop exploration and exploitation
capabilities within Operations, the main characteristics of these
constructs needs to be identified and further understood. Thus, the
objective of this research is to increase the understanding about
exploitation and exploration characteristics, to concretize what they
translates to within the context of improvement and development
work in an Operations unit, and to identify practical challenges. A
literature review and a case study are presented. In the literature
review, different interpretations of exploration and exploitation are
portrayed, key characteristics have been identified, and a deepened
understanding of exploration and exploitation characteristics is
described. The case in the study is an Operations unit, and the aim is
to explore to what extent and in what ways exploration and
exploitation activities are part of the improvement structures and
processes. The contribution includes an identification of key
characteristics of exploitation and exploration, as well as an
interpretation of the constructs. Further, some practical challenges are
identified. For instance, exploration activities tend to be given low
priority, both in daily work as in the manufacturing strategy. Also,
the overall understanding about the concepts of exploitation and
exploration (or any similar aspect of dynamic improvement
capabilities) is very low.
Abstract: This paper describes an optimization tool-based
design strategy for a Current Mode Logic CML divide-by-2 circuit.
Representing a building block for output frequency generation in a
RFID protocol based-frequency synthesizer, the circuit was designed
to minimize the power consumption for driving of multiple loads
with unbalancing (at transceiver level). Implemented with XFAB
XC08 180 nm technology, the circuit was optimized through
MunEDA WiCkeD tool at Cadence Virtuoso Analog Design
Environment ADE.
Abstract: This paper presents a numerical investigation of two
horizontally mounted four-lobed swirl pipes in terms of swirl
induction effectiveness into flows passing through them. The swirl
flows induced by the two swirl pipes have the potential to improve
the efficiency of Clean-In-Place procedures in a closed processing
system by local intensification of hydrodynamic impact on the
internal pipe surface. Pressure losses, swirl development within the
two swirl pipe, swirl induction effectiveness, swirl decay and wall
shear stress variation downstream of two swirl pipes are analyzed and
compared. It was found that a shorter length of swirl inducing pipe
used in joint with transition pipes is more effective in swirl induction
than when a longer one is used, in that it has a less constraint to the
induced swirl and results in slightly higher swirl intensity just
downstream of it with the expense of a smaller pressure loss. The
wall shear stress downstream of the shorter swirl pipe is also slightly
larger than that downstream of the longer swirl pipe due to the
slightly higher swirl intensity induced by the shorter swirl pipe. The
advantage of the shorter swirl pipe in terms of swirl induction is more
significant in flows with a larger Reynolds Number.
Abstract: Brass terminal, one of the several crude oil and
petroleum products storage/handling facilities in the Niger Delta was
built in the 1980s. Activities at this site, over the years, released
crude oil into this 3 m-deep, 1500 m-long canal lying adjacent to the
terminal with oil floating on it and its sediment heavily polluted. To
ensure effective clean-up, three major activities were planned: site
characterization, bioremediation pilot plant construction and testing
and full-scale bioremediation of contaminated sediment / bank soil by
land farming. The canal was delineated into 12 lots and each
characterized, with reference to the floating oily phase, contaminated
sediment and canal bank soil. As a result of site characterization, a
pilot plant for on-site bioremediation was designed and a treatment
basin constructed for carrying out pilot bioremediation test.
Following a designed sampling protocol, samples from this pilot
plant were collected for analysis at two laboratories as a quality
assurance / quality control check. Results showed that Brass Canal
upstream is contaminated with dark, thick and viscous oily film with
characteristic hydrocarbon smell while downstream, thin oily film
interspersed with water was observed. Sediments were observed to be
dark with mixture of brownish sandy soil with TPH ranging from
17,800 mg/kg in Lot 1 to 88,500 mg/kg in Lot 12 samples. Brass
Canal bank soil was observed to be sandy from ground surface to 3m,
below ground surface (bgs) it was silty-sandy and brownish while
subsurface soil (4-10m bgs) was sandy-clayey and whitish/grayish
with typical hydrocarbon smell. Preliminary results obtained so far
have been very promising but were proprietary. This project is
considered, to the best of technical literature knowledge, the first
large-scale on-site bioremediation project in the Niger Delta region,
Nigeria.
Abstract: Agro-industry is one of major industries that have
strong impacts on national economic incomes, growth, stability, and
sustainable development. Moreover, this industry also has strong
influences on social, cultural and political issues. Furthermore, this
industry, as producing primary and secondary products, is facing
challenges from such diverse factors such as demand inconsistency,
intense international competition, technological advancements and
new competitors. In order to maintain and to improve industry’s
competitiveness in both domestics and international markets, science
and technology are key factors. Besides hard sciences and
technologies, modern industrial engineering concepts such as Just in
Time (JIT) Total Quality Management (TQM), Quick Response
(QR), Supply Chain Management (SCM) and Lean can be very
effective to support to increase efficiency and effectiveness of these
agricultural products on world stage. Onion is one of Thailand’s
major export products which bring back national incomes. But, it is
also facing challenges in many ways. This paper focused its interests
in onion packing process and its related activities such as storage and
shipment from one of major packing plant and storage in Mae Wang
District, Chiang Mai, Thailand, by applying Toyota Production
System (TPS) or Lean concepts, to improve process capability
throughout the entire packing and distribution process which will be
profitable for the whole onion supply chain. And it will be beneficial
to other related agricultural products in Thailand and other ASEAN
countries.