Abstract: The sintering step in powder metallurgy (P/M) processes is very sensitive as it determines to a large extent the properties of the final component produced. Spark plasma sintering over the past decade has been extensively used in consolidating a wide range of materials including metallic alloy powders. This novel, non-conventional sintering method has proven to be advantageous offering full densification of materials, high heating rates, low sintering temperatures, and short sintering cycles over conventional sintering methods. Ti6Al4V has been adjudged the most widely used α+β alloy due to its impressive mechanical performance in service environments, especially in the aerospace and automobile industries being a light metal alloy with the capacity for fuel efficiency needed in these industries. The P/M route has been a promising method for the fabrication of parts made from Ti6Al4V alloy due to its cost and material loss reductions and the ability to produce near net and intricate shapes. However, the use of this alloy has been largely limited owing to its relatively poor hardness and wear properties. The effect of sintering temperature on the densification, hardness, and wear behaviors of spark plasma sintered Ti6Al4V powders was investigated in this present study. Sintering of the alloy powders was performed in the 650–850°C temperature range at a constant heating rate, applied pressure and holding time of 100°C/min, 50 MPa and 5 min, respectively. Density measurements were carried out according to Archimedes’ principle and microhardness tests were performed on sectioned as-polished surfaces at a load of 100gf and dwell time of 15 s. Dry sliding wear tests were performed at varied sliding loads of 5, 15, 25 and 35 N using the ball-on-disc tribometer configuration with WC as the counterface material. Microstructural characterization of the sintered samples and wear tracks were carried out using SEM and EDX techniques. The density and hardness characteristics of sintered samples increased with increasing sintering temperature. Near full densification (99.6% of the theoretical density) and Vickers’ micro-indentation hardness of 360 HV were attained at 850°C. The coefficient of friction (COF) and wear depth improved significantly with increased sintering temperature under all the loading conditions examined, except at 25 N indicating better mechanical properties at high sintering temperatures. Worn surface analyses showed the wear mechanism was a synergy of adhesive and abrasive wears, although the former was prevalent.
Abstract: Experimental and analytical studies were accomplished to examine the structural behavior of precast foamed concrete sandwich panel (PFCSP) under vertical in-plane shear load. PFCSP full-scale specimens with total number of six were developed with varying heights to study an important parameter slenderness ratio (H/t). The production technique of PFCSP and the procedure of test setup were described. The results obtained from the experimental tests were analysed in the context of in-plane shear strength capacity, load-deflection profile, load-strain relationship, slenderness ratio, shear cracking patterns and mode of failure. Analytical study of finite element analysis was implemented and the theoretical calculations of the ultimate in-plane shear strengths using the adopted ACI318 equation for reinforced concrete wall were determined aimed at predicting the in-plane shear strength of PFCSP. The decrease in slenderness ratio from 24 to 14 showed an increase of 26.51% and 21.91% on the ultimate in-plane shear strength capacity as obtained experimentally and in FEA models, respectively. The experimental test results, FEA models data and theoretical calculation values were compared and provided a significant agreement with high degree of accuracy. Therefore, on the basis of the results obtained, PFCSP wall has the potential use as an alternative to the conventional load-bearing wall system.
Abstract: The present study addresses the problem of ammonia evaporation during filling of a vertical cylindrical tank and the influence of various external factors on the stability of storage by determining the conditions for minimum evaporation. Numerical simulation is carried out by solving the governing equations namely, continuity, momentum, energy, and diffusion of species. The effect of temperature of surrounding air, the filling speed of the reservoir and the temperature of the filling liquid ammonia on the evaporation rate is investigated. Results show that the temperature of the filling liquid has little effect on the liquid ammonia for a short period, which, in fact, is function of the filling speed. The evaporation rate along the free surface of the liquid is non-uniform. The inlet temperature affects the vapor ammonia temperature because of pressure increase. The temperature of the surrounding air affects the temperature of the vapor phase rather than the liquid phase. The maximum of evaporation is reached at the final step of filling. In order to minimize loss of ammonia vapors automatically causing losses in quantity of the liquid stored, it is suggested to ensure the proper insulation for the walls and roof of the reservoir and to increase the filling speed.
Abstract: TRACE is developed by U.S. NRC for the nuclear
power plants (NPPs) safety analysis. We focus on the establishment
and application of TRACE/FRAPTRAN/SNAP models for Chinshan
NPP (BWR/4) spent fuel pool in this research. The geometry is 12.17
m × 7.87 m × 11.61 m for the spent fuel pool. In this study, there are
three TRACE/SNAP models: one-channel, two-channel, and
multi-channel TRACE/SNAP model. Additionally, the cooling system
failure of the spent fuel pool was simulated and analyzed by using the
above models. According to the analysis results, the peak cladding
temperature response was more accurate in the multi-channel
TRACE/SNAP model. The results depicted that the uncovered of the
fuels occurred at 2.7 day after the cooling system failed. In order to
estimate the detailed fuel rods performance, FRAPTRAN code was
used in this research. According to the results of FRAPTRAN, the
highest cladding temperature located on the node 21 of the fuel rod
(the highest node at node 23) and the cladding burst roughly after 3.7
day.
Abstract: This study is aimed to investigate the influence of
postharvest delays of 1-Methylcyclopropene (1-MCP) treatment on
prolonging the storage potential of melon. Melons were treated with
625-650 ppb 1-MCP at 10 °C for 24 hours on the 1st, 3rd and 5th day
after harvest. Decreased ethylene production and retarded softening
of melon fruits after 7 days of storage at 10 °C plus 3 days of shelflife
were obtained by 1-MCP applications. 1-MCP strongly affected
the chlorophyll fluorescence characteristics and hue angle values of
melon. After shelf-life, the peel color of treated melon was slow in
turning to yellow compared to the control. Additionally, firmness of
melons treated on the first day after harvest was 38% higher than that
of the control fruit. Results showed that fruits treated on the 1st and
the 3rd day after harvest could maintain the quality of melon.
Abstract: Similar to economies in many countries; family-owned enterprises have a significant role in the development of Turkish economy. Although they have a large share in economic terms, their lifetime is limited to working life of their founders. Failure in achieving their sustainability deeply affects not only these businesses but also the economy. Therefore, two basic elements of family owned enterprises, family and organizational culture and especially entrepreneurship culture, should be examined closely. The degree of effectiveness of parents in instilling their children with entrepreneurship culture and their effects on children's profession choices are examined through face-to-face surveys with the managers owning family businesses randomly chosen among family-owned enterprises registered in Konya Chamber of Industry, which are active in specific sectors and which had different generations in their management.
Abstract: Generation Y individuals or Millennials are known for their unique views, work values and motivational needs which implies that, in order to attract and retain those individuals, activities in the area of career management should be given special attention by HRM managers. After a theoretical background on Millennials’ life and work attitudes, an empirical research on career preferences of Millennials in Croatia was described. Empirical research was conducted among 249 members of generation Y. The data analysis revealed that respondents generally perceive promotion opportunities as the most important career aspect; however, job security and work-life balance are almost as important. Furthermore, it was shown that Generation Y is not necessarily a homogenous group. More precisely, women assign greater importance than men to work-life balance and job security. Therefore, HRM managers should adapt career planning activities not only with respect to generational preferences, but individual characteristics as well.
Abstract: The objective of this study is to analyze the evolution of some social and economic indicators of Mercosur´s economies from 1980 to 2012, based on the statistics of the Latin American Integration Association (LAIA). The objective is to observe if after the accession of these economies to Mercosur (the first accessions occurred in 1994) these indicators showed better performance, in order to demonstrate if economic integration contributed to improved trade, macroeconomic performance, and level of social and economic development of member countries. To this end, the methodologies used will be a literature review and descriptive statistics. The theoretical framework that guides the work are the theories of Integration: Classical Liberal, Marxist and structural-proactive. The results reveal that most social and economic indicators showed better performance in those economies that joined Mercosur after 1994. This work is the result of an investigation already completed.
Abstract: Retinoblastoma is a rare type of childhood genetic cancer that affects children worldwide. The diagnosis is often missed due to lack of education and difficulty in presentation of the tumor. Frequently, the tumor on the retina is noticed by photography when the red-eye flash, commonly seen in normal eyes, is not produced. Instead, a yellow or white colored patch is seen or the child has a noticeable strabismus. Early detection can be life-saving though often results in removal of the affected eye. Remaining functioning in the healthy eye when the child is young has resulted in super-vision and high or above-average intelligence. Technological advancement of cameras has helped in early detection. Brain imaging has also made possible early detection of neurological diseases and, together with the monitoring of cortisol levels and yawning frequency, promises to be the next new early diagnostic tool for the detection of neurological diseases where cortisol insufficiency is particularly salient, such as multiple sclerosis and Cushing’s disease.
Abstract: Slope stability analyses are largely carried out by deterministic methods and evaluated through a single security factor. Although it is known that the geotechnical parameters can present great dispersal, such analyses are considered fixed and known. The probabilistic methods, in turn, incorporate the variability of input key parameters (random variables), resulting in a range of values of safety factors, thus enabling the determination of the probability of failure, which is an essential parameter in the calculation of the risk (probability multiplied by the consequence of the event). Among the probabilistic methods, there are three frequently used methods in geotechnical society: FOSM (First-Order, Second-Moment), Rosenblueth (Point Estimates) and Monte Carlo. This paper presents a comparison between the results from deterministic and probabilistic analyses (FOSM method, Monte Carlo and Rosenblueth) applied to a hypothetical slope. The end was held to evaluate the behavior of the slope and consequent risk analysis, which is used to calculate the risk and analyze their mitigation and control solutions. It can be observed that the results obtained by the three probabilistic methods were quite close. It should be noticed that the calculation of the risk makes it possible to list the priority to the implementation of mitigation measures. Therefore, it is recommended to do a good assessment of the geological-geotechnical model incorporating the uncertainty in viability, design, construction, operation and closure by means of risk management.
Abstract: A designing of a structure requires its realization on rough or sloping ground. Besides the problem of the stability of the landslide, the behavior of the foundations that are bearing the structure is influenced by the destabilizing effect of the ground’s slope. This article focuses on the analysis of the slope stability exposed to loading by introducing the different factors influencing the slope’s behavior on the one hand, and on the influence of this slope on the foundation’s behavior on the other hand. This study is about the elastoplastic modelization using FLAC 2D. This software is based on the finite difference method, which is one of the older methods of numeric resolution of differential equations system with initial and boundary conditions. It was developed for the geotechnical simulation calculation. The aim of this simulation is to demonstrate the notable effect of shear modulus « G », cohesion « C », inclination angle (edge) « β », and distance between the foundation and the head of the slope on the stability of the slope as well as the stability of the foundation. In our simulation, the slope is constituted by homogenous ground. The foundation is considered as rigid/hard; therefore, the loading is made by the application of the vertical strengths on the nodes which represent the contact between the foundation and the ground.
Abstract: Energy disaggregation has been focused by many energy companies since energy efficiency can be achieved when the breakdown of energy consumption is known. Companies have been investing in technologies to come up with software and/or hardware solutions that can provide this type of information to the consumer. On the other hand, not all people can afford to have these technologies. Therefore, in this paper, we present a methodology for breaking down the aggregate consumption and identifying the highdemanding end-uses profiles. These energy profiles will be used to build the forecast model for optimal control purpose. A facility with high cooling load is used as an illustrative case study to demonstrate the results of proposed methodology. We apply a high level energy disaggregation through a pattern recognition approach in order to extract the consumption profile of its rooftop packaged units (RTUs) and present a forecast model for the energy consumption.
Abstract: Patient satisfaction represents a crucial aspect in the evaluation of health care services. Preoperative teaching provides the patient with pertinent information concerning the surgical process and the intended surgical procedure as well as anticipated patient behavior (anxiety, fear), expected sensation, and the probable outcomes. Although patient education is part of Accreditation protocols, it is not uniform at most places. The aim of this study was to try to assess the benefit of preoperative patient education on selected post-operative outcome parameters; mainly, post-operative pain scores, requirement of additional analgesia, return to activity of daily living and overall patient satisfaction, and try to standardize few education protocols. Dependent variables were measured before and after the treatment on a study population of 302 volunteers. Educational intervention was provided by the Investigator in the preoperative period to the study group through personal counseling. An information booklet contained detailed information was also provided. Statistical Analysis was done using Chi square test, Mann Whitney u test and Fischer Exact Test on a total of 302 subjects. P value
Abstract: Superstructures like offshore platforms, tall buildings, transition towers, skyscrapers and bridges are normally designed to resist compression, uplift and lateral forces from wind waves, negative skin friction, ship impact and other applied loads. Better understanding and the precise simulation of the response of batter piles under the action of independent uplift loads is a vital topic and an area of active research in the field of geotechnical engineering. This paper investigates the use of finite element code (FEC) to examine the behaviour of model batter piles penetrated in dense sand, subjected to pull-out pressure by means of numerical modelling. The concept of the Winkler Model (beam on elastic foundation) has been used in which the interaction between the pile embedded depth and adjacent soil in the bearing zone is simulated by nonlinear p-y curves. The analysis was conducted on different pile slenderness ratios (lc⁄d) ranging from 7.5, 15.22 and 30 respectively. In addition, the optimum batter angle for a model steel pile penetrated in dense sand has been chosen to be 20° as this is the best angle for this simulation as demonstrated by other researcher published in literature. In this numerical analysis, the soil response is idealized as elasto-plastic and the model piles are described as elastic materials for the purpose of simulation. The results revealed that the applied loads affect the pullout pile capacity as well as the lateral pile response for dense sand together with varying shear strength parameters linked to the pile critical depth. Furthermore, the pile pull-out capacity increases with increasing the pile aspect ratios.
Abstract: The advanced concepts of strategic and innovation management in the sphere of company dynamic and innovation capabilities, and achieving their mutual alignment and a synergy effect, are important elements in business today. This paper analyses the theory and empirically investigates the influence of a company’s dynamic capabilities on its innovation capabilities. A new multidimensional model of dynamic capabilities is presented, consisting of five factors appropriate to real time requirements, while innovation capabilities are considered pursuant to the official OECD and Eurostat standards. After examination of dynamic and innovation capabilities indicated their theoretical links, the empirical study testing the model and examining the influence of a company’s dynamic capabilities on its innovation capabilities showed significant results. In the study, a research model was posed to relate company dynamic and innovation capabilities. One side of the model features the variables that are the determinants of dynamic capabilities defined through their factors, while the other side features the determinants of innovation capabilities pursuant to the official standards. With regard to the research model, five hypotheses were set. The study was performed in late 2014 on a representative sample of large and very large Croatian enterprises with a minimum of 250 employees. The research instrument was a questionnaire administered to company top management. For both variables, the position of the company was tested in comparison to industry competitors, on a fivepoint scale. In order to test the hypotheses, correlation tests were performed to determine whether there is a correlation between each individual factor of company dynamic capabilities with the existence of its innovation capabilities, in line with the research model. The results indicate a strong correlation between a company’s possession of dynamic capabilities in terms of their factors, due to the new multi-dimensional model presented in this paper, with its possession of innovation capabilities. Based on the results, all five hypotheses were accepted. Ultimately, it was concluded that there is a strong association between the dynamic and innovation capabilities of a company.
Abstract: In nearly all earthquakes of the past century that
resulted in moderate to significant damage, the occurrence of postearthquake
fire ignition (PEFI) has imposed a serious hazard and
caused severe damage, especially in urban areas. In order to reduce
the loss of life and property caused by post-earthquake fires, there is
a crucial need for predictive models to estimate the PEFI risk. The
parameters affecting PEFI risk can be categorized as: 1) factors
influencing fire ignition in normal (non-earthquake) condition,
including floor area, building category, ignitability, type of appliance,
and prevention devices, and 2) earthquake related factors contributing
to the PEFI risk, including building vulnerability and earthquake
characteristics such as intensity, peak ground acceleration, and peak
ground velocity. State-of-the-art statistical PEFI risk models are
solely based on limited available earthquake data, and therefore they
cannot predict the PEFI risk for areas with insufficient earthquake
records since such records are needed in estimating the PEFI model
parameters. In this paper, the correlation between normal condition
ignition risk, peak ground acceleration, and PEFI risk is examined in
an effort to offer a means for predicting post-earthquake ignition
events. An illustrative example is presented to demonstrate how such
correlation can be employed in a seismic area to predict PEFI hazard.
Abstract: Introduction: Craniopharyngiomas (CPs) are rare epithelial tumors located mainly in the sellar/parasellar region. CPs have been classified histopathologically, genetically, clinically and prognostically into two distinctive subtypes: adamantinomatous and papillary variants. Aim: To examine the pattern of expression of both the β-catenin and epidermal growth factor receptor (EGFR) in surgically resected samples of adamantinomatous CP, and to asses for the possibility of using anti-EGFR in the management of ACP patients. Materials and methods: β-catenin and EGFR immunostaining was performed on paraffin-embedded tissue sections of 18 ACP cases. Result: 17 out of 18 cases (94%) of ACP exhibited strong nuclear/cytoplasmic expression of β-catenin, 15 (83%) of APC cases were positive for EGFR. Conclusion: Nuclear accumulation of β-catenin is a diagnostic hallmark of ACP. EGFR positivity in most cases of ACP could qualify the use of anti-EGFR therapy.
Abstract: Connected vehicles are equipped with wireless sensors
that aid in Vehicle to Vehicle (V2V) and Vehicle to Infrastructure
(V2I) communication. These vehicles will in the near future
provide road safety, improve transport efficiency, and reduce traffic
congestion. One of the challenges for connected vehicles is how
to ensure that information sent across the network is secure. If
security of the network is not guaranteed, several attacks can occur,
thereby compromising the robustness, reliability, and efficiency of
the network. This paper discusses existing security mechanisms and
unique properties of connected vehicles. The methodology employed
in this work is exploratory. The paper reviews existing security
solutions for connected vehicles. More concretely, it discusses
various cryptographic mechanisms available, and suggests areas
of improvement. The study proposes a combination of symmetric
key encryption and public key cryptography to improve security.
The study further proposes message aggregation as a technique to
overcome message redundancy. This paper offers a comprehensive
overview of connected vehicles technology, its applications, its
security mechanisms, open challenges, and potential areas of future
research.
Abstract: The technological paradigm of the disaster
management field, especially in the case of governmental
intervention strategies, is generally based on rapid and flexible
accommodation solutions. From various technical solution patterns
used to address the immediate housing needs of disaster victims, the
adaptive re-use of existing buildings can be considered to be both
low-cost and practical. However, there is a scarcity of analytical
methods to screen, select and adapt buildings to help decision makers
in cases of emergency. Following an extensive literature review, this
paper aims to highlight key points and problem areas associated with
the adaptive re-use of buildings within the disaster management
context. In other disciplines such as real estate management, the
adaptive re-use potential (ARP) of existing buildings is typically
based on the prioritization of a set of technical and non-technical
criteria which are then weighted to arrive at an economically viable
investment decision. After a disaster, however, the assessment of the
ARP of buildings requires consideration of different/additional layers
of analysis which stem from general disaster management principles
and the peculiarities of different types of disasters, as well as of their
victims. In this paper, a discussion of the development of an adaptive
re-use potential (ARP) assessment model is presented. It is thought
that governmental and non-governmental decision makers who are
required to take quick decisions to accommodate displaced masses
following disasters are likely to benefit from the implementation of
such a model.
Abstract: This study was designed to evaluate whether carvacrol
(CAR) could provide protection against lung injury by acute
pancreatitis development. The rats were randomized into groups to
receive (I) no therapy; (II) 50 μg/kg cerulein at 1h intervals by four
intraperitoneal injections (i.p.); (III) 50, 100 and 200 mg/kg CAR by
one i.p.; and (IV) cerulein+CAR after 2h of cerulein injection. 12h
later, serum samples were obtained to assess pancreatic function the
lipase and amylase values. The animals were euthanized and lung
samples were excised. The specimens were stained with
hematoxylin-eosin (H&E), periodic acid–Schif (PAS), Mallory's
trichrome and amyloid. Additionally, oxidative DNA damage was
determined by measuring as increases in 8-hydroxy-deoxyguanosine
(8-OH-dG) adducts. The results showed that the serum activity of
lipase and amylase in AP rats were significantly reduced after the
therapy (p