Abstract: This work addresses the problem of optimizing
completely batch water-using network with multiple contaminants
where the flow change caused by mass transfer is taken into
consideration for the first time. A mathematical technique for
optimizing water-using network is proposed based on
source-tank-sink superstructure. The task is to obtain the freshwater
usage, recycle assignments among water-using units, wastewater
discharge and a steady water-using network configuration by
following steps. Firstly, operating sequences of water-using units are
determined by time constraints. Next, superstructure is simplified by
eliminating the reuse and recycle from water-using units with
maximum concentration of key contaminants. Then, the non-linear
programming model is solved by GAMS (General Algebra Model
System) for minimum freshwater usage, maximum water recycle and
minimum wastewater discharge. Finally, numbers of operating periods
are calculated to acquire the steady network configuration. A case
study is solved to illustrate the applicability of the proposed approach.
Abstract: Buildings are one of the valuable assets to provide
people with shelters for work, leisure and rest. After years of
attacks by weather, buildings will deteriorate which need proper
maintenance in order to fulfill the requirements and satisfaction of
the users. Poorly managed buildings not just give a negative image
to the city itself, but also pose potential risk hazards to the health
and safety of the general public. As a result, the management of
maintenance projects has played an important role in cities like
Hong Kong where the problem of urban decay has drawn much
attention. However, most research has focused on managing new
construction, and little research effort has been put on maintenance
projects. Given the short duration and more diversified nature of
work, repair and maintenance works are found to be more difficult
to monitor and regulate when compared with new works. Project
participants may face with problems in running maintenance
projects which should be investigated so that proper strategies can
be established. This paper aims to provide a thorough analysis on
the problems of running maintenance projects. A review of
literature on the characteristics of building maintenance projects
was firstly conducted, which forms a solid basis for the empirical
study. Results on the problems and difficulties of running
maintenance projects from the viewpoints of industry practitioners
will also be delivered with a view to formulating effective
strategies for managing maintenance projects successfully.
Abstract: The gas safety management system using an
intelligent gas meter we proposed is to monitor flow and
pressure of gas, earthquake, temperature, smoke and leak of
methane. Then our system takes safety measures to protect a
serious risk by the result of an event, to communicate with a
wall-pad including a gateway by zigbee network in buildings
and to report the event to user by the safety management
program in a server. Also, the inner cutoff valve of an
intelligent gas meter is operated if any event occurred or
abnormal at each sensor.
Abstract: Polymerase chain reaction (PCR) assay and
conventional microbiological methods were used to detect bacterial
contamination of egg shells and egg content in different commercial
housing systems, open house system and evaporative cooling system.
A PCR assay was developed for direct detection using a set of
primers specific for the invasion by A gene (invA) of Salmonella spp.
PCR detected the presence of Salmonella in 2 samples of shell egg
from the evaporative cooling system, while conventional cultural
methods detected no Salmonella from the same samples.
Abstract: In this project cadmium ions were adsorbed from
aqueous solutions onto either date pits; a cheap agricultural and nontoxic
material, or chemically activated carbon prepared from date pits
using phosphoric acid. A series of experiments were conducted in a
batch adsorption technique to assess the feasibility of using the
prepared adsorbents. The effects of the process variables such as
initial cadmium ions concentration, contact time, solution pH and
adsorbent dose on the adsorption capacity of both adsorbents were
studied. The experimental data were tested using different isotherm
models such as Langmuir, Freundlich, Tempkin and Dubinin-
Radushkevich. The results showed that although the equilibrium data
could be described by all models used, Langmuir model gave slightly
better results when using activated carbon while Freundlich model,
gave better results with date pits.
Abstract: Whilst there is growing evidence that activity across
the lifespan is beneficial for improved health, there are also many
changes involved with the aging process and subsequently the
potential for reduced indices of health. The nexus between all forms
of health, physical activity and aging is complex and has raised much
interest in recent times due to the realization that a multifaceted
approached is necessary in order to counteract a growing obesity
epidemic. By investigating age based trends within a population
adherring to competitive sport at older ages, further insight might be
gleaned to assist in understanding one of many factors influencing
this relationship. This study evaluated those sport psychological
constructs of health, physical fitness, mental health states, and social
dimension factors in sport that were associated with factors to
participate in sport and physical activity based on responses from the
2009 World Masters Games in Sydney. The sample consisted of
7846 athletes who competed at the games and who completed a 56
item sports participation survey using a 7-point Likert response (1 -
not important to 7 - very important). Questions focuses on factors
thought to promote participation, such as weight control, living
longer, improving mental health (self-esteem, mood states),
improving physical health and factors related to the athlete-s
competitive perspective. The most significant factors related to
participation with this cohort of masters athletes were the socializing
environment of sport, getting physically fit and improving
competitive personal best performances. Strategies to increase
participation in masters sport should focus on these factors as other
factors such as weight loss, improving mental health and living
longer were not identified as important determinates of sports
participation at the World Masters level.
Abstract: EPC Class-1 Generation-2 UHF tags, one of Radio
frequency identification or RFID tag types, is expected that most
companies are planning to use it in the supply chain in the short term
and in consumer packaging in the long term due to its inexpensive
cost. Because of the very cost, however, its resources are extremely
scarce and it is hard to have any valuable security algorithms in it. It
causes security vulnerabilities, in particular cloning the tags for
counterfeits. In this paper, we propose a product authentication
solution for anti-counterfeiting at application level in the supply chain
and mobile RFID environment. It aims to become aware of
distribution of spurious products with fake RFID tags and to provide a
product authentication service to general consumers with mobile
RFID devices like mobile phone or PDA which has a mobile RFID
reader. We will discuss anti-counterfeiting mechanisms which are
required to our proposed solution and address requirements that the
mechanisms should have.
Abstract: The decision to recruit manpower in an organization
requires clear identification of the criteria (attributes) that distinguish
successful from unsuccessful performance. The choice of appropriate
attributes or criteria in different levels of hierarchy in an organization
is a multi-criteria decision problem and therefore multi-criteria
decision making (MCDM) techniques can be used for prioritization
of such attributes. Analytic Hierarchy Process (AHP) is one such
technique that is widely used for deciding among the complex criteria
structure in different levels. In real applications, conventional AHP
still cannot reflect the human thinking style as precise data
concerning human attributes are quite hard to be extracted. Fuzzy
logic offers a systematic base in dealing with situations, which are
ambiguous or not well defined. This study aims at defining a
methodology to improve the quality of prioritization of an
employee-s performance measurement attributes under fuzziness. To
do so, a methodology based on the Extent Fuzzy Analytic Hierarchy
Process is proposed. Within the model, four main attributes such as
Subject knowledge and achievements, Research aptitude, Personal
qualities and strengths and Management skills with their subattributes
are defined. The two approaches conventional AHP
approach and the Extent Fuzzy Analytic Hierarchy Process approach
have been compared on the same hierarchy structure and criteria set.
Abstract: By using the method of coincidence degree and constructing suitable Lyapunov functional, some sufficient conditions are established for the existence and global exponential stability of antiperiodic solutions for a kind of impulsive Cohen-Grossberg shunting inhibitory cellular neural networks (CGSICNNs) on time scales. An example is given to illustrate our results.
Abstract: Polyphenolics and sugar are the components of many
fruit juices. In this work, the performance of ultra-filtration (UF) for
separating phenolic compounds from apple juice was studied by
performing batch experiments in a membrane module with an area of
0.1 m2 and fitted with a regenerated cellulose membrane of 1 kDa
MWCO. The effects of various operating conditions: transmembrane
pressure (3, 4, 5 bar), temperature (30, 35, 40 ºC), pH (2, 3, 4, 5),
feed concentration (3, 5, 7, 10, 15 ºBrix for apple juice) and feed flow
rate (1, 1.5, 1.8 L/min) on the performance were determined.
The optimum operating conditions were: transmembrane pressure
4 bar, temperature 30 ºC, feed flow rate 1 – 1.8 L/min, pH 3 and 10
Brix (apple juice). After performing ultrafiltration under these
conditions, the concentration of polyphenolics in retentate was
increased by a factor of up to 2.7 with up to 70% recovered in the
permeate and with approx. 20% of the sugar in that stream..
Application of diafiltration (addition of water to the concentrate) can
regain the flux by a factor of 1.5, which has been decreased due to
fouling. The material balance performed on the process has shown
the amount of deposits on the membrane and the extent of fouling in
the system. In conclusion, ultrafiltration has been demonstrated as a
potential technology to separate the polyphenolics and sugars from
their mixtures and can be applied to remove sugars from fruit juice.
Abstract: In H.264/AVC video encoding, rate-distortion
optimization for mode selection plays a significant role to achieve
outstanding performance in compression efficiency and video quality.
However, this mode selection process also makes the encoding
process extremely complex, especially in the computation of the ratedistortion
cost function, which includes the computations of the sum
of squared difference (SSD) between the original and reconstructed
image blocks and context-based entropy coding of the block. In this
paper, a transform-domain rate-distortion optimization accelerator
based on fast SSD (FSSD) and VLC-based rate estimation algorithm
is proposed. This algorithm could significantly simplify the hardware
architecture for the rate-distortion cost computation with only
ignorable performance degradation. An efficient hardware structure
for implementing the proposed transform-domain rate-distortion
optimization accelerator is also proposed. Simulation results
demonstrated that the proposed algorithm reduces about 47% of total
encoding time with negligible degradation of coding performance.
The proposed method can be easily applied to many mobile video
application areas such as a digital camera and a DMB (Digital
Multimedia Broadcasting) phone.
Abstract: Korea Train eXpress (KTX) is now being operated,
which allows Korea being one of the countries that operates the
high-speed rail system. The high-speed rail has its advantage of short
time transportation of population and materials, which lead to many
researches performed in this matter. In the case of high speed classical
trackbed system, the maintenance and usability of gravel ballast
system is costly. Recently, the concrete trackbed structure has been
introduced as a replacement of classical trackbed system. In this case,
the sleeper plays a critical role. Current study investigated to develop
the track sleepers readily applicable to the top of the asphalt trackbed,
as part of the trcakbed study utilizing the asphalt material. Among
many possible shapes and design of sleepers, current study proposed
two types of wide-sleepers according to the shear-key installation
method. The structural behavior analysis and safety evaluation on each
case was conducted using Korean design standard.
Abstract: This paper presents a comparison of average outgoing
quality limit of the MCSP-2-C plan with MCSP-C when MCSP-2-C
has been developed from MCSP-C. The parameters used in MCSP-2-
C are: i (the clearance number), c (the acceptance number), m (the
number of conforming units to be found before allowing c nonconforming
units in the sampling inspection), f1 and f2 (the sampling
frequency at level 1 and 2, respectively). The average outgoing
quality limit (AOQL) values from two plans were compared and we
found that for all sets of i, r, and c values, MCSP-2-C gives higher
values than MCSP-C. For all sets of i, r, and c values, the average
outgoing quality values of MCSP-C and MCSP-2-C are similar when
p is low or high but is difference when p is moderate.
Abstract: This paper suggests a new Affine Projection (AP) algorithm with variable data-reuse factor using the condition number as a decision factor. To reduce computational burden, we adopt a recently reported technique which estimates the condition number of an input data matrix. Several simulations show that the new algorithm has better performance than that of the conventional AP algorithm.
Abstract: Metal matrix composites (MMC) are generating
extensive interest in diverse fields like defense, aerospace, electronics
and automotive industries. In this present investigation, material
removal rate (MRR) modeling has been carried out using an
axisymmetric model of Al-SiC composite during electrical discharge
machining (EDM). A FEA model of single spark EDM was
developed to calculate the temperature distribution.Further, single
spark model was extended to simulate the second discharge. For
multi-discharge machining material removal was calculated by
calculating the number of pulses. Validation of model has been done
by comparing the experimental results obtained under the same
process parameters with the analytical results. A good agreement was
found between the experimental results and the theoretical value.
Abstract: Segmentation, filtering out of measurement errors and
identification of breakpoints are integral parts of any analysis of
microarray data for the detection of copy number variation (CNV).
Existing algorithms designed for these tasks have had some successes
in the past, but they tend to be O(N2) in either computation time or
memory requirement, or both, and the rapid advance of microarray
resolution has practically rendered such algorithms useless. Here we
propose an algorithm, SAD, that is much faster and much less thirsty
for memory – O(N) in both computation time and memory requirement
-- and offers higher accuracy. The two key ingredients of SAD are the
fundamental assumption in statistics that measurement errors are
normally distributed and the mathematical relation that the product of
two Gaussians is another Gaussian (function). We have produced a
computer program for analyzing CNV based on SAD. In addition to
being fast and small it offers two important features: quantitative
statistics for predictions and, with only two user-decided parameters,
ease of use. Its speed shows little dependence on genomic profile.
Running on an average modern computer, it completes CNV analyses
for a 262 thousand-probe array in ~1 second and a 1.8 million-probe
array in 9 seconds
Abstract: Aluminum/Copper clad sheet has been fabricated using
asymmetric extrusion method, which caused severe shear deformation
between Al and Cu plate to easily bond to each other. Interfacial
microstructure and mechanical properties of Al/Cu clad were studied
by scanning electron microscope equipped with energy dispersive
X-ray detector, micro-hardness, and tension tests. The asymmetric
extrusion bonding was very effective to provide a good interface for
atoms diffusion during subsequent annealing. The strength of bonding
was higher with the increasing extrusion ratio.
Abstract: Aluminum salt that is generally presents as a solid
phase in the water purification sludge (WPS) can be dissolved,
recovering a liquid phase, by adding strong acid to the sludge solution.
According to the reaction kinetics, when reactant is in the form of
small particles with a large specific surface area, or when the reaction
temperature is high, the quantity of dissolved aluminum salt or
reaction rate, respectively are high. Therefore, in this investigation,
water purification sludge (WPS) solution was treated with ultrasonic
waves to break down the sludge, and different acids (1 N HCl and 1 N
H2SO4) were used to acidify it. Acid dosages that yielded the solution
pH of less than two were used. The results thus obtained indicate that
the quantity of dissolved aluminum in H2SO4-acidified solution
exceeded that in HCl-acidified solution. Additionally, ultrasonic
treatment increased the rate of dissolution of aluminum and the
amount dissolved. The quantity of aluminum dissolved at 60℃ was 1.5
to 2.0 times higher than that at 25℃.
Abstract: Food control measures are critical in fostering food safety management of a nation. However, no academic study has been undertaken to assess the food control system of Myanmar up to now. The objective of this research paper was to assess the food control system with in depth examination of five key components using desktop analysis and short survey from related food safety program organizations including regulators and inspectors. Study showed that the existing food control system is conventional, mainly focusing on primary health care approach while relying on reactive measures. The achievements of food control work have been limited to a certain extent due to insufficienttechnical capacity that is needed to upgrade staffs, laboratory equipment and technical assistance etc. associated with various sectors. Assessing food control measures is the first step in the integration of food safety management, this paper could assist policy makers in providing information for enhancing the safety and quality of food produced and consumed in Myanmar.
Abstract: In the study the influence of the physical-chemical properties of a liquid, the width of a channel gap and the superficial liquid and gas velocities on the patterns formed during two phase flows in vertical, narrow mini-channels was investigated. The research was performed in the channels of rectangular cross-section and of dimensions: 15 x 0.65 mm and 7.5 x 0.73 mm. The experimental data were compared with the published criteria of the transitions between the patterns of two-phase flows.