Abstract: Custom power is a technology driven product and
service solution which embraces a family devices such as Dynamic
Voltage Restorer (DVR), Distributed Shunt Compensator
(DSTATCOM), Solid State Breaker (SSB) etc which will provide
power quality functions at distribution voltages. The rapid response
of these devices enables them to operate in real time, providing
continuous and dynamic control of the supply including voltage and
reactive power regulation, harmonic reduction and elimination of
voltage dips. This paper presents the benefits of multilevel inverters
when they are used for DPC based custom power devices. Power
flow control mechanism, salient features, advantages and
disadvantages of direct power control (DPC) using lookup table,
SVM, predictive voltage vector and hybrid DPC strategies are
discussed in this paper. Simulation results of three level inverter
based STATCOM, harmonic analysis of multi level inverters are
presented at the end.
Abstract: This paper analyses the torsional efforts in gas turbine-generator shafts caused by high speed automatic reclosing of transmission lines. This issue is especially important for cases of three phase short circuit and unsuccessful reclosure of lines in the vicinity of the thermal plant. The analysis was carried out for the thermal plant TERMOPERNAMBUCO located on Northeast region of Brazil. It is shown that stress level caused by lines unsuccessful reclosing can be several times higher than terminal three-phase short circuit. Simulations were carried out with detailed shaft torsional model provided by machine manufacturer and with the “Alternative Transient Program – ATP" program [1]. Unsuccessful three phase reclosing for selected lines in the area closed to the plant indicated most critical cases. Also, reclosing first the terminal next to the gas turbine gererator will lead also to the most critical condition. Considering that the values of transient torques are very sensible to the instant of reclosing, simulation of unsuccessful reclosing with statistics ATP switch were carried out for determination of most critical transient torques for each section of the generator turbine shaft.
Abstract: The aim of this study was to determine noise level of
six different types of machines in printing companies in Novi Sad.
The A-weighted levels on Leq, Lmax and Lmin Sound Pressure Level
(SPL) in dBA were measured. It was found that the folders, offset
printing presses and binding machines are the predominant noise
sources. The noise levels produced by 12 of 38 machines exceed the
limiting threshold level of 85 dBA, tolerated by law. Since it was
determined that the average noise level for folders (87.7 dB) exceeds
the permitted value the octave analysis of noise was performed.
Abstract: The interrelationship between international stock
markets has been a key study area among the financial market
researchers for international portfolio management and risk
measurement. The characteristics of security returns and their
dynamics play a vital role in the financial market theory. This study
is an attempt to find out the dynamic linkages among the equity
market of USA and emerging markets of Pakistan and India using
daily data covering the period of January 2003–December 2009. The
study utilizes Johansen (Journal of Economic Dynamics and Control,
12, 1988) and Johansen and Juselius (Oxford Bulletin of Economics
and Statistics, 52, 1990) cointegration procedure for long run
relationship and Granger-causality tests based on Toda and
Yamamoto (Journal of Econometrics, 66, 1995) methodology.
No cointegration was found among stock markets of USA, Pakistan
and India, while Granger-causality test showed the evidence of
unidirectional causality running from New York stock exchange to
Bombay and Karachi stock exchanges.
Abstract: Knowledge management is a critical component of
competitive success in service organizations. Knowledge
management centers on creating new knowledge and utilizing
existing knowledge. While utilizing existing knowledge relates to
input and control and can lead to a reduction in costs; creating new
knowledge relates to output and growth and can lead to an increase in
revenue. Therefore managers must ensure that they can successfully
optimize the knowledge and talent in their organizations. To do this
they and must try to develop an environment that promotes the
generation, acquisition, transfer and use of valuable knowledge in
creative ways. However knowledge management is complex and
diverse. Research suggests that organizations in general and SMEs in
particular are finding it difficult to implement successful knowledge
management initiatives. Our research attempts to understand whether
organizations are adopting best practice initiatives in their
organizations. This paper presents findings from an exploratory study
of 139 SMEs operating in the tourism sector across Europe. The
goals of the survey is to assess the level of awareness of knowledge
and talent management strategies and methodologies and to
determine whether the responding companies implement best practice
knowledge management initiatives in their organizations Analysis of
the findings from the study are presented and discussed.
Abstract: A multi-block algorithm and its implementation in two-dimensional finite element numerical model CCHE2D are presented. In addition to a conventional Lagrangian Interpolation Method (LIM), a novel interpolation method, called Consistent Interpolation Method (CIM), is proposed for more accurate information transfer across the interfaces. The consistent interpolation solves the governing equations over the auxiliary elements constructed around the interpolation nodes using the same numerical scheme used for the internal computational nodes. With the CIM, the momentum conservation can be maintained as well as the mass conservation. An imbalance correction scheme is used to enforce the conservation laws (mass and momentum) across the interfaces. Comparisons of the LIM and the CIM are made using several flow simulation examples. It is shown that the proposed CIM is physically more accurate and produces satisfactory results efficiently.
Abstract: Component-Based software engineering provides an
opportunity for better quality and increased productivity in software
development by using reusable software components [10]. One of the
most critical aspects of the quality of a software system is its
performance. The systematic application of software performance
engineering techniques throughout the development process can help
to identify design alternatives that preserve desirable qualities such
as extensibility and reusability while meeting performance objectives
[1]. In the present scenario, software engineering methodologies
strongly focus on the functionality of the system, while applying a
“fix- it-later" approach to software performance aspects [3]. As a
result, lengthy fine-tunings, expensive extra hard ware, or even
redesigns are necessary for the system to meet the performance
requirements. In this paper, we propose design based,
implementation independent, performance prediction approach to
reduce the overhead associated in the later phases while developing a
performance guaranteed software product with the help of Unified
Modeling Language (UML).
Abstract: Extraction of lactic acid by emulsion liquid membrane technology (ELM) using n-trioctyl amine (TOA) in n-heptane as carrier within the organic membrane along with sodium carbonate as acceptor phase was optimized by using response surface methodology (RSM). A three level Box-Behnken design was employed for experimental design, analysis of the results and to depict the combined effect of five independent variables, vizlactic acid concentration in aqueous phase (cl), sodium carbonate concentration in stripping phase (cs), carrier concentration in membrane phase (ψ), treat ratio, and batch extraction time (τ)
with equal volume of organic and external aqueous phase on lactic acid extraction efficiency. The maximum lactic acid extraction efficiency (ηext) of 98.21%from aqueous phase in a batch reactor using ELM was found at the optimized values for test variables, cl, cs, ψ, and τ as 0.06 [M], 0.18 [M], 4.72 (%,v/v), 1.98 (v/v) and 13.36 min respectively.
Abstract: This paper describes dynamic analysis using proposed
fast finite element method for a shock absorbing structure including a
sponge. The structure is supported by nonlinear concentrated springs.
The restoring force of the spring has cubic nonlinearity and linear
hysteresis damping. To calculate damping properties for the structures
including elastic body and porous body, displacement vectors as
common unknown variable are solved under coupled condition. Under
small amplitude, we apply asymptotic method to complex eigenvalue
problem of this system to obtain modal parameters. And then
expressions of modal loss factor are derived approximately. This
approach was proposed by one of the authors previously. We call this
method as Modal Strain and Kinetic Energy Method (MSKE method).
Further, using the modal loss factors, the discretized equations in
physical coordinate are transformed into the nonlinear ordinary
coupled equations using normal coordinate corresponding to linear
natural modes. This transformation yields computation efficiency. As
a numerical example of a shock absorbing structures, we adopt double
skins with a sponge. The double skins are supported by nonlinear
concentrated springs. We clarify influences of amplitude of the input
force on nonlinear and chaotic responses.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece using copper tools are being optimized
according to its individual machining characteristic i.e. Electrode
Wear Ratio (EWR). Higher EWR would give bad dimensional
precision for the EDM machined workpiece because of high
electrode wear. Hence, the quality characteristic for EWR is set to
lower-the-better to achieve the optimum dimensional precision for
the machined workpiece. Taguchi method has been used for the
construction, layout and analysis of the experiment for EWR
machining characteristic. The use of Taguchi method in the
experiment saves a lot of time and cost of preparing and machining
the experiment samples. Therefore, an L18 Orthogonal array
which was the fundamental component in the statistical design of
experiments has been used to plan the experiments and Analysis of
Variance (ANOVA) is used to determine the optimum machining
parameters for this machining characteristic. The control
parameters selected for this optimization experiments are polarity,
pulse on duration, discharge current, discharge voltage, machining
depth, machining diameter and dielectric liquid pressure. The
result had shown that negative polarity machining parameter
setting will decreases EWR.
Abstract: In recent times there has been a growing interest in the
development of quasi-two-dimensional niobium pentoxide (Nb2O5)
as a semiconductor for the potential electronic applications such as
capacitors, filtration, dye-sensitised solar cells and gas sensing
platforms. Therefore once the purpose is established, Nb2O5 can be
prepared in a number of nano- and sub-micron-structural
morphologies that include rods, wires, belts and tubes. In this study
films of Nb2O5 were prepared on gold plated silicon substrate using
spin-coating technique and subsequently by mechanical exfoliation.
The reason this method was employed was to achieve layers of less
than 15nm in thickness. The sintering temperature of the specimen
was 800oC. The morphology and structural characteristics of the
films were analyzed by Atomic Force Microscopy (AFM), Raman
Spectroscopy, X-ray Photoelectron Spectroscopy (XPS).
Abstract: In this paper, an attempt has been made to obtain nonsensitive
solutions in the multi-objective optimization of a
photovoltaic/thermal (PV/T) air collector. The selected objective
functions are overall energy efficiency and exergy efficiency.
Improved thermal, electrical and exergy models are used to calculate
the thermal and electrical parameters, overall energy efficiency,
exergy components and exergy efficiency of a typical PV/T air
collector. A computer simulation program is also developed. The
results of numerical simulation are in good agreement with the
experimental measurements noted in the previous literature. Finally,
multi-objective optimization has been carried out under given
climatic, operating and design parameters. The optimized ranges of
inlet air velocity, duct depth and the objective functions in optimal
Pareto front have been obtained. Furthermore, non-sensitive solutions
from energy or exergy point of view in the results of multi-objective
optimization have been shown.
Abstract: Sexual behavior and semen charactertistics were
evaluated in young male Boer goats in tropical condition during time
period of September to November 2009. The animal was let to have
adaptation for five months after importation from Australian climate.
A total of 20 bucks were observed for sexual behavior and ability of
semen production. Out of this number, 4 faild to libido and 3
produced poor semen. The remaing 13 animals were divided into
three groups according to the ages (11-13, 15-16 and 18-25 months).
Sexual behavior consisting response time to female teaser,
ejaculation time, fixing strenght to female and erection status were
normaly observer in 13 bucks, and there was no significant difference
between age groups. Semen characteristics from 13 bucks were in
normal quality in the volume, sperm mass motility, individual
motility, percentage of live- and abnormal sperm. We concluded that
is possible to collect semen of Boer goats during the period of
September to November under tropical condition. Collection during
other time period should be analyzed.
Abstract: Oleic acid (C18:1) play an important role in
proliferation of fat cells. In this study, the effect of oleate on cells
viability in 3T3-L1 cells (fat cells) was investigated. The 3T3-L1
cells were treated with various concentrations of oleate in the
presence of 23 mM glucose. Oleate was added to adipogenic media
(day 0) to investigate the influence of oleate on proliferation of
postconfluent preadipocytes after 24 h induction. 0.1 mM oleate
promoted cell division by increasing 33.9% number of cells from
basal control in postconfluent preadipocytes. However, there were no
significantly different in cells viability with control cells when oleate
concentrations were increased up to 0.5 mM. When added to
differentiated adipocytes (day 12) for 48 h, the number of cells
decreased as oleate concentrations increased. 92.7% of cells lost
demonstrated apoptosis and necrosis after 48 h with 0.5 mM oleate.
The fluorochrome staining was examined under fluorescence
microscopy using acridine orange and ethidium bromide double
staining. Furthermore, the presence of high lactate (60.6% increased
from basal control) released into plasma has shown the direct
cytotoxicity of 0.5 mM oleate on adipocytes.
Abstract: Using DNA microarrays the comparative analysis of a
gene expression profiles is carried out in a liver and kidneys of pigs.
The hypothesis of a cross hybridization of one probe with different
cDNA sites of the same gene or different genes is checked up, and it
is shown, that cross hybridization can be a source of essential errors
at revealing of a key genes in organ-specific transcriptome. It is
reveald that distinctions in profiles of a gene expression are well coordinated
with function, morphology, biochemistry and histology of
these organs.
Abstract: The objective of this research work is to discuss the concept of “green growth” in the Republic of Kazakhstan introduced by its government in the “National Sustainable Development Strategy” with the objective of transition to a resource-efficient, “green economy.” We believe that emerging economies like Kazakhstan can pursue a cleaner and more efficient development path by introducing an environmental tax system based on resource consumption rather than only income and labor. The key issues discussed in this article are the eco-efficiency, which refers to closing the gap between economic and ecological efficiencies, and the structural change of the economy toward “green growth.” We also strongly believe that studying the experience of East Asian countries on “green reform” including eco-innovation and “green solutions” in business is essential to the case of Kazakhstan. All of these will raise the status of Kazakhstan to the level of one of the thirty developed countries over the next decades.
Abstract: The potential of antioxidant activities of the plant
extract Gynura procumbens, Achyranthes aspera and Polygenum
tomentosum were studied by using 1, 1-diphenyl-2-picrylhydrazyl
(DPPH) .Antioxidant activity was qualitatively and quantitatively
determined. In this analysis , Ascorbic acid (Vitamin C) was used as
the standard .The antioxidant activities were observed all three plant
extracts and the EC50 values of G procumbens A.aspera and
P.tomemtosum were 13.7 μg /ml,14.37 μg /ml and 14.35 μg /ml.
Among these plants, G.procumbens is more potent antioxidant
activity then others. Antitumor activities were found with A.aspera
(s2) extracts in the dose of 100ppm in carrot disks and G.procumbens
(s1) and P.tomentosum (s3) in the dose of 1000 ppm. Therefore, these
herbal plants are used in traditional medicines.
Abstract: Adjacent Hall microsensors, comprising a silicon
substrate and four contacts, providing simultaneously two supply inputs and two differential outputs, are characterized. The voltage
related sensitivity is in the order of 0.11T-1, and a cancellation method for offset compensation is used, achieving residual offset in
the micro scale which is also compared to a single Hall plate.
Abstract: Silicon nanowire (SiNW) based thermoelectric device (TED) has potential applications in areas such as chip level cooling/ energy harvesting. It is a great challenge however, to assemble an efficient device with these SiNW. The presence of parasitic in the form of interfacial electrical resistance will have a significant impact on the performance of the TED. In this work, we explore the effect of the electrical contact resistance on the performance of a TED. Numerical simulations are performed on SiNW to investigate such effects on its cooling performance. Intrinsically, SiNW individually without the unwanted parasitic effect has excellent cooling power density. However, the cooling effect is undermined with the contribution of the electrical contact resistance.
Abstract: Analytically the effect of polarization dependent loss on a high speed fiber optic communication link has been investigated. PDL and the signal's incoming state of polarization (SOP) have a significant co-relation between them and their various combinations produces different effects on the system behavior which has been inspected. Pauli's spin operator and PDL parameters are combined together to observe the attenuation effect induced by PDL in a link containing multiple PDL elements. It is found that in the presence of PDL the Q-factor and BER at the receiver undergoes fluctuation causing the system to be unstable and results show that it is mainly due to optical-signal-to-parallel-noise ratio (OSNItpar) that these parameters fluctuate. Generally the Q-factor, BER deteriorates as the value of average PDL in the link increases except for depolarized light for which the system parameters improves when PDL increases.