Abstract: This paper presents a hybrid three phase rectifier for
high power factor application. This rectifier is composed by zero
voltage transition (ZVT) and zero current transition (ZCT) boost
converter with three phase diode bridge rectifier, in parallel with a six
pulse three phase pulse width modulation (PWM) controlled rectifier.
The proposed topology is capable of high power factor with DC
output voltage regulation by providing sinusoidal input. Also, it
increases the overall efficiency of the new hybrid rectifier to 94.56%
and the total harmonic distortion of the hybrid structure varies from
0% to 16% at nominal output power. This topology was simulated in
MATLAB/SIMULINK environment and the output waveforms
presented with experimental result.
Abstract: Persea declinata (Bl.) Kosterm is a member of the
Lauraceae family, widely distributed in Southeast Asia. It is from the
same genus with avocado (Persea americana Mill), which is widely
consumed as food and for medicinal purposes. In the present study,
we examined the anticancer properties of Persea declinata (Bl.)
Kosterm bark methanolic crude extract (PDM). PDM exhibited a
potent antiproliferative effect in MCF-7 human breast cancer cells,
with an IC50 value of 16.68 .g/mL after 48h of treatment. We
observed that PDM caused cell cycle arrest and subsequent apoptosis
in MCF-7 cells, as exhibited by increased population at G0/G1 phase,
higher lactate dehydrogenase (LDH) release, and DNA
fragmentation. Mechanistic studies showed that PDM caused
significant elevation in ROS production, leading to perturbation of
mitochondrial membrane potential, cell permeability, and activation
of caspases-3/7. On the other hand, real-time PCR and Western blot
analysis showed that PDM treatment increased the expression of the
proapoptotic molecule, Bax, but decreased the expression of
prosurvival proteins, Bcl-2 and Bcl-xL, in a dose-dependent manner.
These findings imply that PDM could inhibit proliferation in MCF-7
cells via cell cycle arrest and apoptosis induction, indicating its
potential as a therapeutic agent worthy of further development.
Abstract: The manufacturing technology of band cotton is very
delicate and depends to choice of certain parameters such as torsion
of warp yarn.
The fabric elasticity is achieved without the use of any elastic
material, chemical expansion, artificial or synthetic and it’s capable
of creating pressures useful for therapeutic treatments.
Before use, the band is subjected to treatments of specific
preparation for obtaining certain elasticity, however, during its
treatment, there are some regression parameters. The dependence of
manufacturing parameters on the quality of the chemical treatment
was confirmed.
The aim of this work is to improve the properties of the fabric
through the development of manufacturing technology appropriately.
Finally for the treatment of the strip pancake 100% cotton, a
treatment method is recommended.
Abstract: This article presents summary on preparation and
characterization of zinc, copper, cadmium and cobalt chromite
nanocrystals, embedded in an amorphous silica matrix. The
ZnCr2O4/SiO2, CuCr2O4/SiO2, CdCr2O4/SiO2 and CoCr2O4/SiO2
nanocomposites were prepared by a conventional sol-gel method
under acid catalysis. Final heat treatment of the samples was carried
out at temperatures in the range of 900−1200 ◦C to adjust the
phase composition and the crystallite size, respectively. The resulting
samples were characterized by Powder X-ray diffraction (PXRD),
High Resolution Transmission Electron Microscopy (HRTEM),
Raman/FTIR spectroscopy and magnetic measurements. Formation
of the spinel phase was confirmed in all samples. The average size of
the nanocrystals was determined from the PXRD data and by direct
particle size observation on HRTEM; both results were correlated.
The mean particle size (reviewed by HRTEM) was in the range from
∼4 to 46 nm. The results showed that the sol-gel method can be
effectively used for preparation of the spinel chromite nanoparticles
embedded in the silica matrix and the particle size is driven by the
type of the cation A2+ in the spinel structure and the temperature
of the final heat treatment. Magnetic properties of the nanocrystals
were found to be just moderately modified in comparison to the bulk
phases.
Abstract: The fundamental issues in ICT Governance (ICTG)
implementation for Malaysian Public Sector (MPS) is how ICT be
applied to support improvements in productivity, management
effectiveness and the quality of services offered to its citizens. Our
main concern is to develop and adopt a common definition and
framework to illustrate how ICTG can be used to better align ICT
with government’s operations and strategic focus. In particular, we
want to identify and categorize factors that drive a successful ICTG
process. This paper presents the results of an exploratory study to
identify, validate and refine such Critical Success Factors (CSFs) and
confirmed seven CSFs and nineteen sub-factors as influential factors
that fit MPS after further validated and refined. The Delphi method
applied in validation and refining process before being endorsed as
appropriate for MPS. The identified CSFs reflect the focus areas that
need to be considered strategically to strengthen ICT Governance
implementation and ensure business success.
Abstract: Load Forecasting plays a key role in making today's
and future's Smart Energy Grids sustainable and reliable. Accurate
power consumption prediction allows utilities to organize in advance
their resources or to execute Demand Response strategies more
effectively, which enables several features such as higher
sustainability, better quality of service, and affordable electricity
tariffs. It is easy yet effective to apply Load Forecasting at larger
geographic scale, i.e. Smart Micro Grids, wherein the lower available
grid flexibility makes accurate prediction more critical in Demand
Response applications. This paper analyses the application of
short-term load forecasting in a concrete scenario, proposed within the
EU-funded GreenCom project, which collect load data from single
loads and households belonging to a Smart Micro Grid. Three
short-term load forecasting techniques, i.e. linear regression, artificial
neural networks, and radial basis function network, are considered,
compared, and evaluated through absolute forecast errors and training
time. The influence of weather conditions in Load Forecasting is also
evaluated. A new definition of Gain is introduced in this paper, which
innovatively serves as an indicator of short-term prediction
capabilities of time spam consistency. Two models, 24- and
1-hour-ahead forecasting, are built to comprehensively compare these
three techniques.
Abstract: Metal-enhanced Luminescence of silicon nanocrystals
(SiNCs) was determined using two different particle sizes of silver
nanoparticles (AgNPs). SiNCs have been characterized by scanning
electron microscopy (SEM), high resolution transmission electron
microscopy (HRTEM), Fourier transform infrared spectroscopy
(FTIR) and X-ray photoelectron spectroscopy (XPS). It is found that
the SiNCs are crystalline with an average diameter of 65 nm and FCC
lattice. AgNPs were synthesized using photochemical reduction of
AgNO3 with sodium dodecyl sulphate (SDS). The enhanced
luminescence of SiNCs by AgNPs was evaluated by confocal Raman
microspectroscopy. Enhancement up to x9 and x3 times were
observed for SiNCs that mixed with AgNPs which have an average
particle size of 100 nm and 30 nm, respectively. Silver NPs-enhanced
luminescence of SiNCs occurs as a result of the coupling between the
excitation laser light and the plasmon bands of AgNPs; thus this
intense field at AgNPs surface couples strongly to SiNCs.
Abstract: Artemisia species, which are medically beneficial, are
widespread in temperate regions of both Northern and Southern
hemispheres among which Iran is located. About 35 species of
Artemisia are indigenous in Iran among them some are widespread in
all or most provinces, yet some are restricted to some specific
regions. In this review paper, initially, GC-Mass results of some
experiments done in different provinces of Iran are mentioned among
them some compounds are common among species, some others are
mostly restricted to other species; after that, medical advantages
based on some researches on species of this genus are reviewed;
different qualities such as anti-leishmania, anti-bacteria, antiviral as
well as anti-proliferative could be mentioned.
Abstract: The aim of the paper was to elaborate a novel calculator BasWilCalc, that allows to estimate the actual amount of biomass on the basket willow plantations. The proposed method is based on the results of field experiment conducted during years 2011-2013 on basket willow plantation in the south-western part of Poland. As input data the results of destructive measurements of the diameter, length and weight of willow stems and non-destructive biometric measurements of diameter in the middle of stems and their length during the growing season performed at weekly intervals were used. Performed analysis enabled to develop the algorithm which, due to the fact that energy plantations are of known and constant planting structure, allows to estimate the actual amount of willow basket biomass on the plantation with a given probability and accuracy specified by the model, based on the number of stems measured and the age of the plantation.
Abstract: The mathematical analysis on radiation obtained and
the development of the solar photovoltaic (PV) array groundwater
pumping is needed in the rural areas of Thohoyandou for sizing and
power performance subject to the climate conditions within the area.
A simple methodology approach is developed for the directed
coupled solar, controller and submersible ground water pump system.
The system consists of a PV array, pump controller and submerged
pump, battery backup and charger controller. For this reason, the
theoretical solar radiation is obtained for optimal predictions and
system performance in order to achieve different design and
operating parameters. Here the examination of the PV schematic
module in a Direct Current (DC) application is used for obtainable
maximum solar power energy for water pumping. In this paper, a
simple efficient photovoltaic water pumping system is presented with
its theoretical studies and mathematical modeling of photovoltaics
(PV) system.
Abstract: Calcium phosphate coating (CaP) has been employed
for protein delivery, but the typical direct protein adsorption on the
coating led to low incorporation content and fast release of the
protein from the coating. By using bovine serum albumin (BSA) as a
model protein, rapid biomimetic co-precipitation between calcium
phosphate and BSA was employed to control the distribution of BSA
within calcium phosphate coating during biomimetic formation on
titanium surface for only 6 h at 50oC in an accelerated calcium
phosphate solution. As a result, the amount of BSA incorporation and
release duration could be increased by using a rapid biomimetic coprecipitation
technique. Up to 43 fold increases in the BSA
incorporation content and the increase from 6 h to more than 360 h in
release duration compared to typical direct adsorption technique were
observed depending on the initial BSA concentration used during coprecipitation
(1, 10 and 100 μg.ml-1). From x-ray diffraction and
Fourier transform infrared spectroscopy studies, the coating
composition was not altered with the incorporation of BSA by this
rapid biomimetic co-precipitation and mainly comprised octacalcium
phosphate and hydroxyapatite. However, the microstructure of
calcium phosphate crystals changed from straight, plate-like units to
curved, plate-like units with increasing BSA content.
Abstract: In Capitalism all economic activity rests upon a set of
core institutional foundations, main from which are privately owned
capital assets and profit. How these core institutional foundations are
working in former soviet countries, in particular in Travel and
Tourism Industry of Georgia?
The role of Travel and Tourism as a key pillar of economic growth
is being increasingly recognized by governments in all regions of the
world. For the last few years Georgia succeeded in the World Bank
and IFC “Doing Business” rankings. Despite of that, during decades
totally different statistical data of the tourism sector were provided by
the different State bodies; economic parameters were published few,
or not published at all.
The frequency and extent of property rights violation in Georgia
has repeatedly been the subject of concern for the last decade. Total
value of abrogated by the former Georgian Government private
property is estimated approximately in US$4-5 billion.
Thus, if economic profitability is unknown and property rights are
not protected – that means that the main institutional foundations of
capitalism in Georgia, are not working properly yet, that cause
management problems at all levels of the national Travel and
Tourism industry of Georgia.
Abstract: The success of any retail business is predisposed by its
swift response and its knack in understanding the constraints and the
requirements of customers. In this paper a conceptual design model
of an automated customer-friendly supermarket has been proposed.
In this model a 10-sided, space benefited, regular polygon shaped
gravity shelves have been designed for goods storage and effective
customer-specific algorithms have been built-in for quick automatic
delivery of the randomly listed goods. The algorithm is developed
with two main objectives, viz., delivery time and priority. For
meeting these objectives the randomly listed items are reorganized
according to the critical-path of the robotic arm specific to the
identified shop and its layout and the items are categorized according
to the demand, shape, size, similarity and nature of the product for an
efficient pick-up, packing and delivery process. We conjectured that
the proposed automated supermarket model reduces business
operating costs with much customer satisfaction warranting a winwin
situation.
Abstract: The discarded clam shell waste, fossil and edible oil
as biolubricant feedstocks create environmental impacts and food
chain dilemma, thus this work aims to circumvent these issues by
using activated saltwater clam shell waste (SCSW) as solid catalyst
for conversion of Jatropha curcas oil as non-edible sources to ester
biolubricant. The characterization of solid catalyst was done by
Differential Thermal Analysis-Thermo Gravimetric Analysis (DTATGA),
X-Ray Fluorescence (XRF), X-Ray Diffraction (XRD),
Brunauer-Emmett-Teller (BET), Field Emission Scanning Electron
Microscopy (FESEM) and Fourier Transformed Infrared
Spectroscopy (FTIR) analysis. The calcined catalyst was used in the
transesterification of Jatropha oil to methyl ester as the first step, and
the second stage was involved the reaction of Jatropha methyl ester
(JME) with trimethylolpropane (TMP) based on the various process
parameters. The formated biolubricant was analyzed using the
capillary column (DB-5HT) equipped Gas Chromatography (GC).
The conversion results of Jatropha oil to ester biolubricant can be
found nearly 96.66%, and the maximum distribution composition
mainly contains 72.3% of triester (TE).
Abstract: For a given a simple connected graph, we present
some new bounds via a new approach for a special topological index
given by the sum of the real number power of the non-zero
normalized Laplacian eigenvalues. To use this approach presents an
advantage not only to derive old and new bounds on this topic but
also gives an idea how some previous results in similar area can be
developed.
Abstract: An anthropometric study applied to 1,115 students of
the Faculty of Chemical Sciences and Engineering of the
Autonomous University of California. Thirteen individual
measurements were taken in a sitting position. The results obtained
allow forming a reliable anthropometric database for statistical
studies and analysis and inferences of specific distributions, so the
opinion of experts in occupational medicine recommendations may
emit to reduce risks resulting in an alteration of the vital signs during
the execution of their school activities. Another use of these analyses
is to use them as a reliable reference for future deeper research, to the
design of spaces, tools, utensils, workstations, with anthropometric
dimensions and ergonomic characteristics suitable to use.
Abstract: This paper presents an anthropometric study
conducted to 300 employees in a maquiladora industry that belongs
to the cluster of medical products as part of a research project to
pretend simulate workplace conditions under which operators
conduct their activities. This project is relevant because traditionally
performed a study to design ergonomic workspaces according to
anthropometric profile of users, however, this paper demonstrates the
importance of making decisions when the infrastructure cannot be
adapted for economic whichever put emphasis on user activity.
Abstract: Economic Dispatch (ED) is one of the most
challenging problems of power system since it is difficult to determine
the optimum generation scheduling to meet the particular load demand
with the minimum fuel costs while all constraints are satisfied. The
objective of the Economic Dispatch Problems (EDPs) of electric
power generation is to schedule the committed generating units
outputs so as to meet the required load demand at minimum operating
cost while satisfying all units and system equality and inequality
constraints. In this paper, an efficient and practical steady-state genetic
algorithm (SSGAs) has been proposed for solving the economic
dispatch problem. The objective is to minimize the total generation
fuel cost and keep the power flows within the security limits. To
achieve that, the present work is developed to determine the optimal
location and size of capacitors in transmission power system where,
the Participation Factor Algorithm and the Steady State Genetic
Algorithm are proposed to select the best locations for the capacitors
and determine the optimal size for them.
Abstract: Historical and ancestral bonds of the countries in the
Middle East have led to similarities in culture and context of their
societies. In addition, economical resources, such as the oil industry,
have generally been an integrative point in the region. Higher
education of a country is influenced by different national and
international factors and, regarding the mentioned bonds, it is inviting
to study the development of the countries of the Middle East in
higher education and draw some practical implications which can be
used in the educational policymaking of the region. This review
includes a data analysis on the population of international students in
the countries of the Middle East. As its second objective, a review
study on the successful countries, that is, those which host the highest
number of international students, and the strategies they have
developed to reach this state among the countries of the region, has
been conducted. Suggestions are made as to the strategies in higher
education systems of these countries which could prove useful and
practical in the development of internationalization of higher
education in the region, specifically with regard to the recruitment of
international students.
Abstract: A circularly polarized fractal boundary microstrip
antenna is presented. The sides of a square patch along x- axis, yaxis
are replaced with Minkowski and Koch curves correspondingly.
By using the fractal curves as edges, asymmetry in the structure is
created to excite two orthogonal modes for circular polarization (CP)
operation. The indentation factors of the fractal curves are optimized
for pure CP. The simulated results of the novel polyfractal antenna
are demonstrated.