Abstract: In MANET, mobile nodes communicate with each
other using the wireless channel where transmission takes place with
significant interference. The wireless medium used in MANET is a
shared resource used by all the nodes available in MANET. Packet
reserving is one important resource management scheme which
controls the allocation of bandwidth among multiple flows through
node cooperation in MANET. This paper proposes packet reserving
and clogging control via Routing Aware Packet Reserving (RAPR)
framework in MANET. It mainly focuses the end-to-end routing
condition with maximal throughput. RAPR is complimentary system
where the packet reserving utilizes local routing information
available in each node. Path setup in RAPR estimates the security
level of the system, and symbolizes the end-to-end routing by
controlling the clogging. RAPR reaches the packet to the destination
with high probability ratio and minimal delay count. The standard
performance measures such as network security level,
communication overhead, end-to-end throughput, resource utilization
efficiency and delay measure are considered in this work. The results
reveals that the proposed packet reservation and clogging control via
Routing Aware Packet Reserving (RAPR) framework performs well
for the above said performance measures compare to the existing
methods.
Abstract: This paper considers the characterization of a complex
electromagnetic environment due to multiple sources of
electromagnetic radiation as a five-dimensional surface which can be
described by a set of several surface sections including: instant EM
field intensity distribution maps at a given frequency and altitude,
instantaneous spectrum at a given location in space and the time
evolution of the electromagnetic field spectrum at a given point in
space. This characterization if done over time can enable the
exposure levels of Radio Frequency Radiation at every point in the
analysis area to be determined and results interpreted based on
comparison of the determined RFR exposure level with the safe
guidelines for general public exposure given by recognized body
such as the International commission on non-ionizing radiation
protection (ICNIRP), Institute of Electrical and Electronic Engineers
(IEEE), the National Radiation Protection Authority (NRPA).
Abstract: This paper presents a 4-DOF nonlinear model of a
cracked de Laval rotor-stator system derived based on Energy
Principles. The model has been used to simulate coupled torsionallateral
response of the faulty system with multiple parametric
excitations; rotor-stator-rub, a breathing transverse crack, eccentric
mass and an axial force. Nonlinearity of a “breathing” crack is
incorporated in the model using a simple hinge mechanism suitable
for a shallow crack. Response of the system while passing via its
critical speed with intermittent rotor-stator rub is analyzed. Effects of
eccentricity with phase and acceleration are investigated. Features of
crack, rub and eccentricity in vibration response are explored for
condition monitoring. The presence of a crack and rub are observable
in the power spectrum despite excitations by an axial force and rotor
unbalance. Obtained results are consistent with existing literature and
could be adopted into rotor condition monitoring strategies.
Abstract: The article discusses multimodal mobility in
contemporary societies as a main planning and organization issue in
the functioning of administrative bodies, a problem which really
exists in the space of contemporary cities in terms of shaping modern
transport systems. The article presents classification of available
resources and initiatives undertaken for developing multimodal
mobility. Solutions can be divided into three groups of measures –
physical measures in the form of changes of the transport network
infrastructure, organizational ones (including transport policy) and
information measures. The latter ones include in particular direct
support for people travelling in the transport network by providing
information about ways of using available means of transport. A
special measure contributing to this end is a trip planner. The article
compares several selected planners. It includes a short description of
the Green Travelling Project, which aims at developing a planner
supporting environmentally friendly solutions in terms of transport
network operation. The article summarizes preliminary findings of
the project.
Abstract: A relationship between face and signature biometrics
is established in this paper. A new approach is developed to predict
faces from signatures by using artificial intelligence. A multilayer
perceptron (MLP) neural network is used to generate face details
from features extracted from signatures, here face is the physical
biometric and signatures is the behavioural biometric. The new
method establishes a relationship between the two biometrics and
regenerates a visible face image from the signature features.
Furthermore, the performance efficiencies of our new technique are
demonstrated in terms of minimum error rates compared to published
work.
Abstract: In this paper, design of solid-state battery/supercapacitor emulator based on dc-dc boost converter is described.
The emulator mimics charging behavior of any storage device based
on a predefined behavior set by the user. The device is operated by a
two-level control structure: high-level emulating controller and low-
level input voltage controller. Simulation and experimental results are
shown to demonstrate the emulator operation.
Abstract: Innovations not only contribute to competitiveness of
the company but have also positive effects on revenues. On average,
product innovations account to 14 percent of companies’ sales.
Innovation management has substantially changed during the last
decade, because of growing reliance on external partners. As a
consequence, a new task for purchasing arises, as firms need to
understand which suppliers actually do have high potential
contributing to the innovativeness of the firm and which do not.
Proper organization of the purchasing function is important since
for the majority of manufacturing companies deal with substantial
material costs which pass through the purchasing function. In the past
the purchasing function was largely seen as a transaction-oriented,
clerical function but today purchasing is the intermediate with supply
chain partners contributing to innovations, be it product or process
innovations. Therefore, purchasing function has to be organized
differently to enable firm innovation potential.
However, innovations are inherently risky. There are behavioral
risk (that some partner will take advantage of the other party),
technological risk in terms of complexity of products and processes
of manufacturing and incoming materials and finally market risks,
which in fact judge the value of the innovation. These risks are
investigated in this work. Specifically, technological risks which deal
with complexity of the products, and processes will be investigated
more thoroughly. Buying components or such high edge technologies
necessities careful investigation of technical features and therefore is
usually conducted by a team of experts. Therefore it is hypothesized
that higher the technological risk, higher will be the centralization of
the purchasing function as an interface with other supply chain
members.
Main contribution of this research lies is in the fact that analysis
was performed on a large data set of 1493 companies, from 25
countries collected in the GMRG 4 survey. Most analyses of
purchasing function are done by case study analysis of innovative
firms. Therefore this study contributes with empirical evaluations that
can be generalized.
Abstract: The use of IT equipment has become a part of every
day. However, each device that is part of cyberspace should be
secured against unauthorized use. It is very important to know the
basics of these security devices, but also the basics of safe conduct
their owners. This information should be part of every curriculum
computer science education in primary and secondary schools.
Therefore, the work focuses on the education of pupils in primary and
secondary schools on the Internet. Analysis of the current state
describes approaches to the education of pupils in security issues on
the Internet. The paper presents a questionnaire-based survey which
was carried out in the Czech Republic, whose task was to ascertain
the level of opinion pupils in primary and secondary schools on the
issue of communication in social networks. The research showed that
awareness of socio-pathological phenomena on the Internet
environment is very low. Based on the results it was proposed
appropriate ways of teaching to this issue and its inclusion a proposal
of curriculum for primary and secondary schools.
Abstract: Health analytics (HA) is used in healthcare systems
for effective decision making, management and planning of
healthcare and related activities. However, user resistances, unique
position of medical data content and structure (including
heterogeneous and unstructured data) and impromptu HA projects
have held up the progress in HA applications. Notably, the accuracy
of outcomes depends on the skills and the domain knowledge of the
data analyst working on the healthcare data. Success of HA depends
on having a sound process model, effective project management and
availability of supporting tools. Thus, to overcome these challenges
through an effective process model, we propose a HA process model
with features from rational unified process (RUP) model and agile
methodology.
Abstract: Characterization of the engineering behavior of
unsaturated soil is dependent on the soil-water characteristic curve
(SWCC), a graphical representation of the relationship between water
content or degree of saturation and soil suction. A reasonable
description of the SWCC is thus important for the accurate prediction
of unsaturated soil parameters. The measurement procedures for
determining the SWCC, however, are difficult, expensive, and timeconsuming.
During the past few decades, researchers have laid a
major focus on developing empirical equations for predicting the
SWCC, with a large number of empirical models suggested. One of
the most crucial questions is how precisely existing equations can
represent the SWCC. As different models have different ranges of
capability, it is essential to evaluate the precision of the SWCC
models used for each particular soil type for better SWCC estimation.
It is expected that better estimation of SWCC would be achieved via
a thorough statistical analysis of its distribution within a particular
soil class. With this in view, a statistical analysis was conducted in
order to evaluate the reliability of the SWCC prediction models
against laboratory measurement. Optimization techniques were used
to obtain the best-fit of the model parameters in four forms of SWCC
equation, using laboratory data for relatively coarse-textured (i.e.,
sandy) soil. The four most prominent SWCCs were evaluated and
computed for each sample. The result shows that the Brooks and
Corey model is the most consistent in describing the SWCC for sand
soil type. The Brooks and Corey model prediction also exhibit
compatibility with samples ranging from low to high soil water
content in which subjected to the samples that evaluated in this study.
Abstract: Web-based Cognitive Writing Instruction (WeCWI) is
a hybrid e-framework for the development of a web-based instruction
(WBI), which contributes towards instructional design and language
development. WeCWI divides its contribution in instructional design
into macro and micro perspectives. In macro perspective, being a 21st
century educator by disseminating knowledge and sharing ideas with
the in-class and global learners is initiated. By leveraging the virtue
of technology, WeCWI aims to transform an educator into an
aggregator, curator, publisher, social networker and ultimately, a
web-based instructor. Since the most notable contribution of
integrating technology is being a tool of teaching as well as a
stimulus for learning, WeCWI focuses on the use of contemporary
web tools based on the multiple roles played by the 21st century
educator. The micro perspective in instructional design draws
attention to the pedagogical approaches focusing on three main
aspects: reading, discussion, and writing. With the effective use of
pedagogical approaches through free reading and enterprises,
technology adds new dimensions and expands the boundaries of
learning capacity. Lastly, WeCWI also imparts the fundamental
theories and models for web-based instructors’ awareness such as
interactionist theory, cognitive information processing (CIP) theory,
computer-mediated communication (CMC), e-learning interactionalbased
model, inquiry models, sensory mind model, and leaning styles
model.
Abstract: Immunomodulators are substances that alter immune
system via dynamic regulation of messenger molecules. It can be
divided into immunostimulant and immunosuppressant. It can help to
increase immunity of people with a low immune system, and also can
help to normalize an overactive immune system. Aim of this study is
to investigate the effects of in vitro exposure to low and high doses of
several immunomodulators which include caffeine, kaloba and
quercetin on antigen-stimulated whole blood culture cytokine
production. Whole blood samples were taken from 5 healthy males
(age: 32 ± 12 years; weight: 75.7 ± 6.1 kg; BMI: 24.3 ± 1.5 kg/m2)
following an overnight fast with no vigorous activity during the
preceding 24 h. The whole blood was then stimulated with 50 μl of
100 x diluted Pediacel vaccine and low or high dose of
immunomodulators in the culture plate. After 20 h incubation (5%
CO2, 37°C), it was analysed using the Evidence Investigator to
determine the production of cytokines including IL-2, IL-4, IL-10,
IFN-γ, and IL-1α. Caffeine and quercetin showed a tendency towards
decrease cytokine production as the doses were increased. On the
other hand, an upward trend was evident with kaloba, where a high
dose of kaloba seemed to increase the cytokine production. In
conclusion, we found that caffeine and quercetin have potential as
immunosuppressant and kaloba as immunostimulant.
Abstract: Caused by shorter product life cycles and higher
product variety the importance of production ramp ups is increasing.
Even though companies are aware of that fact, up to 40% of the ramp
up projects still miss technical and economical requirements. The
success of a ramp up depends on the planning of human factors,
organizational aspects and technological solutions. Since only partly
considered in scientific literature, this paper lays its focus on the
human factor during production ramp up. There are only incoherent
methods which address the problems in this area. A systematic and
holistic method to improve the capabilities of the employees during
ramp up is missing. The Harada Method is a relatively young
approach for developing highly-skilled workers. It consists of
different worksheets which help employees to set guidelines and
reach overall objectives. This approach is going to be transferred into
a tool for ramp up management.
Abstract: A wireless sensor network (WSN) is a collection of
sensor nodes organized into a cooperative network. These nodes
communicate through a wireless antenna. Reduction in physical size
and multiband operation is an important requirement of WSN
antenna. Fractal antenna is used for miniaturization and multiband
operation. The self-similar or self-affine and space filling property of
fractal geometry increases the effective electrical length of the
antenna, reduces the size and make them frequency independent. This
paper elaborates on Dual band fractal antenna with Coplanar
Waveguide (CPW) feed for WSN. The proposed antenna is designed
on a FR4 substrate with the dimension of 27mm x 28.5mm x 1.6mm,
resonates at 2.4GHz and 5.2GHz with a return loss less than -10dB.
The design and simulation process is carried out using IE3D
simulation software. The simulated and measured results are found in
good agreement.
Abstract: The effect of trucks on the level of service is
determined by considering passenger car equivalents (PCE) of trucks.
The current version of Highway Capacity Manual (HCM) uses a
single PCE value for all tucks combined. However, the composition
of truck traffic varies from location to location; therefore, a single
PCE value for all trucks may not correctly represent the impact of
truck traffic at specific locations. Consequently, present study
developed separate PCE values for single-unit and combination
trucks to replace the single value provided in the HCM on different
freeways. Site specific PCE values, were developed using concept of
spatial lagging headways (that is the distance between rear bumpers
of two vehicles in a traffic stream) measured from field traffic data.
The study used data from four locations on a single urban freeway
and three different rural freeways in Indiana. Three-stage-leastsquares
(3SLS) regression techniques were used to generate models
that predicted lagging headways for passenger cars, single unit trucks
(SUT), and combination trucks (CT). The estimated PCE values for
single-unit and combination truck for basic urban freeways (level
terrain) were: 1.35 and 1.60, respectively. For rural freeways the
estimated PCE values for single-unit and combination truck were:
1.30 and 1.45, respectively. As expected, traffic variables such as
vehicle flow rates and speed have significant impacts on vehicle
headways. Study results revealed that the use of separate PCE values
for different truck classes can have significant influence on the LOS
estimation.
Abstract: In the present work, the effects of additives, including
contents of the added antioxidants and type of the selected metallic
stearates (either calcium stearate (CaSt) or zinc stearate (ZnSt)), on
the thermal stabilities of carbon black (CB)/high density polyethylene
(HDPE) compounds were studied. The results showed that the AO
contents played a key role in the thermal stabilities of the CB/HDPE
compounds — the higher the AO content, the higher the thermal
stabilities. Although the CaSt-containing compounds were slightly
superior to those with ZnSt in terms of the thermal stabilities, the
remaining solid residue of CaSt after heated to the temperature of 600
°C (mainly calcium carbonate (CaCO3) as characterized by the X-ray
diffraction (XRD) technique) seemed to catalyze the decomposition
of CB in the HDPE-based compounds. Hence, the quantification of
CB in the CaSt-containing compounds with a muffle furnace gave an
inaccurate CB content — much lower than actual value. However,
this phenomenon was negligible in the ZnSt-containing system.
Abstract: Polyethylene (PE), Polypropylene (PP), Polyethylene
(vinyl acetate) (EVA) and PE-ionomer nanocomposite samples were
prepared by mixing of the polymer with organofilized
montmorillonite fillers Cloisite 93A and Dellite 67G. The amount of
each modified montmorillonite (MMT) was fixed to 5% (w/w). The
twin-screw kneader was used for the compounding of polymer matrix
and chosen nanofillers. The level of MMT exfoliation was studied by
the transmission electron microscopy (TEM) observations. The
mechanical properties of prepared materials were evaluated by
dynamical mechanical analysis at 30°C and by the measurement of
tensile properties (stress and strain at break).
Abstract: Different order modulations combined with different
coding schemes, allow sending more bits per symbol, thus achieving
higher throughputs and better spectral efficiencies. However, it must
also be noted that when using a modulation technique such as 64-
QAM with less overhead bits, better signal-to-noise ratios (SNRs) are
needed to overcome any Inter symbol Interference (ISI) and maintain
a certain bit error ratio (BER). The use of adaptive modulation allows
wireless technologies to yielding higher throughputs while also
covering long distances. The aim of this paper is to implement an
Adaptive Modulation and Coding (AMC) features of the WiMAX
PHY in MATLAB and to analyze the performance of the system in
different channel conditions (AWGN, Rayleigh and Rician fading
channel) with channel estimation and blind equalization. Simulation
results have demonstrated that the increment in modulation order
causes to increment in throughput and BER values. These results
derived a trade-off among modulation order, FFT length, throughput,
BER value and spectral efficiency. The BER changes gradually for
AWGN channel and arbitrarily for Rayleigh and Rician fade
channels.
Abstract: This study was conducted to evaluate the manganese
removal from aqueous solution using Banana peels activated carbon
(BPAC). Batch experiments have been carried out to determine the
influence of parameters such as pH, biosorbent dose, initial metal ion
concentrations and contact times on the biosorption process. From
these investigations, a significant increase in percentage removal of
manganese 97.4% is observed at pH value 5.0, biosorbent dose 0.8 g,
initial concentration 20 ppm, temperature 25 ± 2°C, stirring rate 200
rpm and contact time 2h. The equilibrium concentration and the
adsorption capacity at equilibrium of the experimental results were
fitted to the Langmuir and Freundlich isotherm models; the Langmuir
isotherm was found to well represent the measured adsorption data
implying BPAC had heterogeneous surface. A raw groundwater
samples were collected from Baharmos groundwater treatment plant
network at Embaba and Manshiet Elkanater City/District-Giza,
Egypt, for treatment at the best conditions that reached at first phase
by BPAC. The treatment with BPAC could reduce iron and
manganese value of raw groundwater by 91.4% and 97.1%,
respectively and the effect of the treatment process on the
microbiological properties of groundwater sample showed decrease
of total bacterial count either at 22°C or at 37°C to 85.7% and 82.4%,
respectively. Also, BPAC was characterized using SEM and FTIR
spectroscopy.
Abstract: As the human race will continue to explore the space
by creating new space transportation means and sending them to other
planets, the enhance of atmospheric reentry study is crucial. In this
context, an analysis of mass recession rate of ablative materials for
thermal shields of reentry spacecrafts is important to be carried out.
The paper describes a new estimation method for calculating the mass
recession of an ablator system made of carbon fiber reinforced plastic
materials. This method is based on Arrhenius equation for low
temperatures and, for high temperatures, on a theory applied for the
recession phenomenon of carbon fiber reinforced plastic materials,
theory which takes into account the presence of the resin inside the
materials. The space mission of USERS spacecraft is considered as a
case study.