Abstract: This paper aims at finding a suitable neural network
for monitoring congestion level in electrical power systems. In this
paper, the input data has been framed properly to meet the target
objective through supervised learning mechanism by defining normal
and abnormal operating conditions for the system under study. The
congestion level, expressed as line congestion index (LCI), is
evaluated for each operating condition and is presented to the NN
along with the bus voltages to represent the input and target data.
Once, the training goes successful, the NN learns how to deal with a
set of newly presented data through validation and testing
mechanism. The crux of the results presented in this paper rests on
performance comparison of a multi-layered feed forward neural
network with eleven types of back propagation techniques so as to
evolve the best training criteria. The proposed methodology has been
tested on the standard IEEE-14 bus test system with the support of
MATLAB based NN toolbox. The results presented in this paper
signify that the Levenberg-Marquardt backpropagation algorithm
gives best training performance of all the eleven cases considered in
this paper, thus validating the proposed methodology.
Abstract: The mineral bioflotation represents a viable
alternative for the evaluation of new processes benefit alternative.
The adsorption bacteria on minerals surfaces will depend mainly on
the type of the microorganism as well as of the studied mineral
surface. In the current study, adhesion of S. carnosus on coal was
studied. Several methods were used as: DRX, Fourier Transform
Infra-Red (FTIR) adhesion isotherms and kinetic. The main goal is to
recovery of organic matter by the microflotation process on coal
particles with biological reagent (S. carnosus). Adhesion tests
revealed that adhesion took place after of 8 h at pH 9. The results
suggest that the adhesion of bacteria to solid substrates can be
considered an abiotic physicochemical process that is consequently
governed by bacterial surface properties such as their specific surface
area, hydrophobicity and surface functionalities. The greatest coal
fine flotability was of 75%, after 5 min of flotation.
Abstract: Currently, biological control programs in greenhouse
crops involve the use, at the same time, several natural enemies
during the crop cycle. Also, large number of plant species grown in
greenhouses, among them, the used cultivars are also wide. However,
the cultivar effects on entomophagous species efficacy (predators and
parasitoids) have been scarcely studied. A new method had been
developed, using the factitious prey or host Ephestia kuehniella. It
allow us to evaluate, under greenhouse or controlled conditions
(semi-field), the cultivar effects on the entomophagous species
effectiveness. The work was carried out in greenhouse tomato crop. It
has been found the biological and ecological activities of predatory
species (Nesidiocoris tenuis) and egg-parasitoid (Trichogramma
achaeae) can be well represented with the use of the factitious prey
or host; being better in the former than the latter. The data found in
the trial are shown and discussed. The developed method could be
applied to evaluate new plant materials before making available to
farmers as commercial varieties, at low costs and easy use.
Abstract: Composite materials have important assets compared
to traditional materials. They bring many functional advantages:
lightness, mechanical resistance and chemical, etc. In the present
study we examine the effect of a circular central notch and a precrack
on the tensile fracture of two woven composite materials. The tensile
tests were applied to a standardized specimen, notched and a
precarcked (orientation of the crack 0°, 45° and 90°). These tensile
tests were elaborated according to an experimental planning design of
the type 23.31 requiring 24 experiments with three repetitions. By the
analysis of regression, we obtained a mathematical model describing
the maximum load according to the influential parameters (hole
diameter, precrack length, angle of a precrack orientation). The
specimens precracked at 90° have a better behavior than those having
a precrack at 45° and still better than those having of the precracks
oriented at 0°. In addition the maximum load is inversely
proportional to the notch size.
Abstract: The paper describes the experiments and the kinetic
parameters calculus of the gasoil hydrofining. They are presented
experimental results of gasoil hidrofining using Mo and promoted
with Ni on aluminum support catalyst. The authors have adapted a
kinetic model gasoil hydrofining. Using this proposed kinetic model
and the experimental data they have calculated the parameters of the
model. The numerical calculus is based on minimizing the difference
between the experimental sulf concentration and kinetic model
estimation.
Abstract: The article is devoted to the problem of political
discourse and its reflection on mass cognition. This article is
dedicated to describe the myth as one of the main features of political
discourse. The dominance of an expressional and emotional
component in the myth is shown. Precedent phenomenon plays an
important role in distinguishing the myth from the linguistic point of
view. Precedent phenomena show the linguistic cognition, which is
characterized by their fame and recognition. Four types of myths
such as master myths, a foundation myth, sustaining myth,
eschatological myths are observed. The myths about the national idea
are characterized by national specificity. The main aim of the
political discourse with the help of myths is to influence on the mass
consciousness in order to motivate the addressee to certain actions so
that the target purpose is reached owing to unity of forces.
Abstract: Color Histogram is considered as the oldest method
used by CBIR systems for indexing images. In turn, the global
histograms do not include the spatial information; this is why the
other techniques coming later have attempted to encounter this
limitation by involving the segmentation task as a preprocessing step.
The weak segmentation is employed by the local histograms while
other methods as CCV (Color Coherent Vector) are based on strong
segmentation. The indexation based on local histograms consists of
splitting the image into N overlapping blocks or sub-regions, and
then the histogram of each block is computed. The dissimilarity
between two images is reduced, as consequence, to compute the
distance between the N local histograms of the both images resulting
then in N*N values; generally, the lowest value is taken into account
to rank images, that means that the lowest value is that which helps to
designate which sub-region utilized to index images of the collection
being asked. In this paper, we make under light the local histogram
indexation method in the hope to compare the results obtained against
those given by the global histogram. We address also another
noteworthy issue when Relying on local histograms namely which
value, among N*N values, to trust on when comparing images, in
other words, which sub-region among the N*N sub-regions on which
we base to index images. Based on the results achieved here, it seems
that relying on the local histograms, which needs to pose an extra
overhead on the system by involving another preprocessing step
naming segmentation, does not necessary mean that it produces better
results. In addition to that, we have proposed here some ideas to
select the local histogram on which we rely on to encode the image
rather than relying on the local histogram having lowest distance with
the query histograms.
Abstract: Frequent pattern mining is the process of finding a
pattern (a set of items, subsequences, substructures, etc.) that occurs
frequently in a data set. It was proposed in the context of frequent
itemsets and association rule mining. Frequent pattern mining is used
to find inherent regularities in data. What products were often
purchased together? Its applications include basket data analysis,
cross-marketing, catalog design, sale campaign analysis, Web log
(click stream) analysis, and DNA sequence analysis. However, one of
the bottlenecks of frequent itemset mining is that as the data increase
the amount of time and resources required to mining the data
increases at an exponential rate. In this investigation a new algorithm
is proposed which can be uses as a pre-processor for frequent itemset
mining. FASTER (FeAture SelecTion using Entropy and Rough sets)
is a hybrid pre-processor algorithm which utilizes entropy and roughsets
to carry out record reduction and feature (attribute) selection
respectively. FASTER for frequent itemset mining can produce a
speed up of 3.1 times when compared to original algorithm while
maintaining an accuracy of 71%.
Abstract: This paper presents a 3D guidance scheme for
Unmanned Aerial Vehicles (UAVs). The proposed guidance scheme
is based on the sliding mode approach using nonlinear sliding
manifolds. Generalized 3D kinematic equations are considered
here during the design process to cater for the coupling between
longitudinal and lateral motions. Sliding mode based guidance
scheme is then derived for the multiple-input multiple-output
(MIMO) system using the proposed nonlinear manifolds. Instead of
traditional sliding surfaces, nonlinear sliding surfaces are proposed
here for performance and stability in all flight conditions. In the
reaching phase control inputs, the bang-bang terms with signum
functions are accompanied with proportional terms in order to reduce
the chattering amplitudes. The Proposed 3D guidance scheme is
implemented on a 6-degrees-of-freedom (6-dof) simulation of a UAV
and simulation results are presented here for different 3D trajectories
with and without disturbances.
Abstract: The relationship between eigenstructure (eigenvalues
and eigenvectors) and latent structure (latent roots and latent vectors)
is established. In control theory eigenstructure is associated with
the state space description of a dynamic multi-variable system and
a latent structure is associated with its matrix fraction description.
Beginning with block controller and block observer state space forms
and moving on to any general state space form, we develop the
identities that relate eigenvectors and latent vectors in either direction.
Numerical examples illustrate this result. A brief discussion of the
potential of these identities in linear control system design follows.
Additionally, we present a consequent result: a quick and easy
method to solve the polynomial eigenvalue problem for regular matrix
polynomials.
Abstract: Two types of commercial cylindrical lithium ion
batteries (Panasonic 3.4 Ah NCR-18650B and Samsung 2.9 Ah
INR-18650), were investigated experimentally. The capacities of these
samples were individually measured using constant current-constant
voltage (CC-CV) method at different ambient temperatures (-10°C,
0°C, 25°C). Their internal resistance was determined by
electrochemical impedance spectroscopy (EIS) and pulse discharge
methods. The cells with different configurations of parallel connection
NCR-NCR, INR-INR and NCR-INR were charged/discharged at the
aforementioned ambient temperatures. The results showed that the
difference of internal resistance between cells much more evident at
low temperatures. Furthermore, the parallel connection of NCR-NCR
exhibits the most uniform temperature distribution in cells at -10°C,
this feature is quite favorable for the safety of the battery pack.
Abstract: During welding, the amount of heat present in weld
zones determines the quality of weldment produced. Thus, the heat
distribution characteristics and its magnitude in weld zones with
respect to process variables such as tool pin-shoulder rotational and
traveling speed during welding is analyzed using thermal finite
element analyses method. For this purpose, transient thermal finite
element analyses are performed to model the temperatures
distribution and its quantities in weld-zones with respect to process
variables such as rotational speed and traveling speed during welding.
Commercially available software Altair HyperWork is used to model
three-dimensional tool pin-shoulder vs. workpieces and to simulate
the friction stir process. The results show that increasing tool
rotational speed, at a constant traveling speed, will increase the
amount of heat generated in weld-zones. In contrary, increasing
traveling speed, at constant tool pin-shoulder rotational speeds, will
reduce the amount of heat generated in weld zones.
Abstract: The paper discusses economic policy of Georgia
aiming to increase national competitiveness as well as the tools and
means which will help to improve the competitiveness of the country.
The sectors of the economy, in which the country can achieve the
competitive advantage, are studied. It is noted that the country’s
economic policy plays an important role in obtaining and maintaining
the competitive advantage - authority should take measures to ensure
high level of education; scientific and research activities should be
funded by the state; foreign direct investments should be attracted
mainly in science-intensive industries; adaptation with the latest
scientific achievements of the modern world and deepening of
scientific and technical cooperation. Stable business environment and
export oriented strategy is the basis for the country’s economic
growth.
As the outcome of the research, the paper suggests the strategy for
improving competitiveness in Georgia; recommendations are
provided based on relevant conclusions.
Abstract: Among all FACTS devices, the unified power flow
controller (UPFC) is considered to be the most versatile device.
This is due to its capability to control all the transmission system
parameters (impedance, voltage magnitude, and phase angle). With
the growing interest in UPFC, the attention to develop a mathematical
model has increased. Several models were introduced for UPFC in
literature for different type of studies in power systems. In this paper
a novel comparison study between two dynamic models of UPFC
with their proposed control strategies.
Abstract: Researches and concerns in power quality gained
significant momentum in the field of power electronics systems over
the last two decades globally. This sudden increase in the number of
concerns over power quality problems is a result of the huge increase
in the use of non-linear loads. In this paper, power quality evaluation
of some distribution networks at Misurata - Libya has been done
using a power quality and energy analyzer (Fluke 437 Series II). The
results of this evaluation are used to minimize the problems of power
quality. The analysis shows the main power quality problems that
exist and the level of awareness of power quality issues with the aim
of generating a start point which can be used as guidelines for
researchers and end users in the field of power systems.
Abstract: The generalized wave equation models various
problems in sciences and engineering. In this paper, a new three-time
level implicit approach based on cubic trigonometric B-spline for the
approximate solution of wave equation is developed. The usual finite
difference approach is used to discretize the time derivative while
cubic trigonometric B-spline is applied as an interpolating function in
the space dimension. Von Neumann stability analysis is used to
analyze the proposed method. Two problems are discussed to exhibit
the feasibility and capability of the method. The absolute errors and
maximum error are computed to assess the performance of the
proposed method. The results were found to be in good agreement
with known solutions and with existing schemes in literature.
Abstract: From an organizational perspective, leaders are a
variation of the same talent pool in that they all score a larger than
average value on the bell curve that maps leadership behaviors and
characteristics, namely competence, vision, communication,
confidence, cultural sensibility, stewardship, empowerment,
authenticity, reinforcement, and creativity. The question that remains
unanswered and essentially unresolved is how to explain the irony
that leaders are so much alike yet their organizations diverge so
noticeably in their ability to innovate. Leadership intersects with
innovation at the point where human interactions get exceedingly
complex and where certain paradoxical forces cohabit: conflict with
conciliation, sovereignty with interdependence, and imagination with
realism. Rather than accepting that leadership is without context, we
argue that leaders are specialists of their domain and that those
effective at leading for innovation are distinct within the broader pool
of leaders. Keeping in view the extensive literature on leadership and
innovation, we carried out a quantitative study with data collected
over a five-year period involving 240 participants from across five
dissimilar companies based in the United States. We found that while
innovation and leadership are, in general, strongly interrelated (r =
.89, p = 0.0), there are five qualities that set leaders apart on
innovation. These qualities include a large radius of trust, a restless
curiosity with a low need for acceptance, an honest sense of self and
other, a sense for knowledge and creativity as the yin and yang of
innovation, and an ability to use multiple senses in the engagement
with followers. When these particular behaviors and characteristics
are present in leaders, organizations out-innovate their rivals by a
margin of 29.3 per cent to gain an unassailable edge in a business
environment that is regularly disruptive. A strategic outcome of this
study is a psychometric scale named iLeadership, proposed with the
underlying evidence, limitations, and potential for leadership and
innovation in organizations.c
Abstract: This paper presents a new meta-heuristic bio-inspired
optimization algorithm which is called Cuttlefish Algorithm (CFA).
The algorithm mimics the mechanism of color changing behavior of
the cuttlefish to solve numerical global optimization problems. The
colors and patterns of the cuttlefish are produced by reflected light
from three different layers of cells. The proposed algorithm considers
mainly two processes: reflection and visibility. Reflection process
simulates light reflection mechanism used by these layers, while
visibility process simulates visibility of matching patterns of the
cuttlefish. To show the effectiveness of the algorithm, it is tested with
some other popular bio-inspired optimization algorithms such as
Genetic Algorithms (GA), Particle Swarm Optimization (PSO) and
Bees Algorithm (BA) that have been previously proposed in the
literature. Simulations and obtained results indicate that the proposed
CFA is superior when compared with these algorithms.
Abstract: Three dimensional non-Interlaced carbon fibre
reinforced silicon carbide (3-D-Cf/SiC) composites with pyrocarbon
interphase were fabricated using isothermal chemical vapor
infiltration (ICVI) combined with polymer impregnation pyrolysis
(PIP) process. Polysilazane (PSZ) is used as a preceramic polymer to
obtain silicon carbide matrix. Thermo gravimetric analysis (TGA),
Infrared spectroscopic analysis (IR) and X-ray diffraction (XRD)
analysis were carried out on PSZ pyrolysed at different temperatures
to understand the pyrolysis and obtaining the optimum pyrolysing
condition to yield β-SiC phase. The density of the composites was
1.94 g cm-3 after the 3-D carbon preform was SiC infiltrated for 280 h
with one intermediate polysilazane pre-ceramic PIP process.
Mechanical properties of the composite materials were investigated
under tensile, flexural, shear and impact loading. The values of
tensile strength were 200 MPa at room temperature (RT) and 195
MPa at 500°C in air. The average RT flexural strength was 243 MPa.
The lower flexural strength of these composites is because of the
porosity. The fracture toughness obtained from single edge notched
beam (SENB) technique was 39 MPa.m1/2. The work of fracture
obtained from the load-displacement curve of SENB test was 22.8
kJ.m-2. The composites exhibited excellent impact resistance and the
dynamic fracture toughness of 44.8 kJ.m-2 is achieved as determined
from instrumented Charpy impact test. The shear strength of the
composite was 93 MPa, which is significantly higher compared 2-D
Cf/SiC composites. Microstructure evaluation of fracture surfaces
revealed the signatures of fracture processes and showed good
support for the higher toughness obtained.
Abstract: This study aimed at designing and developing a
mechanical force gauge for the square watermelon mold for the first
time. It also tried to introduce the square watermelon characteristics
and its production limitations. The mechanical force gauge
performance and the product itself were also described. There are
three main designable gauge models: a. hydraulic gauge, b. strain
gauge, and c. mechanical gauge. The advantage of the hydraulic
model is that it instantly displays the pressure and thus the force
exerted by the melon. However, considering the inability to measure
forces at all directions, complicated development, high cost, possible
hydraulic fluid leak into the fruit chamber and the possible influence
of increased ambient temperature on the fluid pressure, the
development of this gauge was overruled. The second choice was to
calculate pressure using the direct force a strain gauge. The main
advantage of these strain gauges over spring types is their high
precision in measurements; but with regard to the lack of conformity
of strain gauge working range with water melon growth, calculations
were faced with problems. Finally the mechanical pressure gauge has
advantages, including the ability to measured forces and pressures on
the mold surface during melon growth; the ability to display the peak
forces; the ability to produce melon growth graph thanks to its
continuous force measurements; the conformity of its manufacturing
materials with the required physical conditions of melon growth; high
air conditioning capability; the ability to permit sunlight reaches the
melon rind (no yellowish skin and quality loss); fast and
straightforward calibration; no damages to the product during
assembling and disassembling; visual check capability of the product
within the mold; applicable to all growth environments (field,
greenhouses, etc.); simple process; low costs and so forth.