Abstract: Meshless Finite Element Methods, namely element-free Galerkin and point-interpolation method were implemented and tested concerning their applicability to typical engineering problems like electrical fields and structural mechanics. A class-structure was developed which allows a consistent implementation of these methods together with classical FEM in a common framework. Strengths and weaknesses of the methods under investigation are discussed. As a result of this work joint usage of meshless methods together with classical Finite Elements are recommended.
Abstract: Rural areas of Tanzania are still disadvantaged in terms of diffusion of IP-based services; this is due to lack of Information and Communication Technology (ICT) infrastructures, especially lack of connectivity. One of the limitations for connectivity problems in rural areas of Tanzania is the high cost to establish infrastructures for IP-based services [1-2]. However the cost of connectivity varies from one technology to the other and at the same time, the cost is also different from one operator (service provider) to another within the country. This paper presents development of software system to calculate cost of connectivity to rural areas of Tanzania. The system is developed to make an easy access of connectivity cost from different technologies and different operators. The development of the calculator follows the V-model software development lifecycle. The calculator is used to evaluate the economic viability of different technologies considered as being potential candidates to provide rural connectivity. In this paper, the evaluation is based on the techno-economic analysis approach.
Abstract: Iris localization is a very important approach in
biometric identification systems. Identification process usually is
implemented in three levels: iris localization, feature extraction, and
pattern matching finally. Accuracy of iris localization as the first step
affects all other levels and this shows the importance of iris
localization in an iris based biometric system. In this paper, we
consider Daugman iris localization method as a standard method,
propose a new method in this field and then analyze and compare the
results of them on a standard set of iris images. The proposed method
is based on the detection of circular edge of iris, and improved by
fuzzy circles and surface energy difference contexts. Implementation
of this method is so easy and compared to the other methods, have a
rather high accuracy and speed. Test results show that the accuracy of
our proposed method is about Daugman method and computation
speed of it is 10 times faster.
Abstract: Psoriasis is a widespread skin disease affecting up to 2% population with plaque psoriasis accounting to about 80%. It can be identified as a red lesion and for the higher severity the lesion is usually covered with rough scale. Psoriasis Area Severity Index (PASI) scoring is the gold standard method for measuring psoriasis severity. Scaliness is one of PASI parameter that needs to be quantified in PASI scoring. Surface roughness of lesion can be used as a scaliness feature, since existing scale on lesion surface makes the lesion rougher. The dermatologist usually assesses the severity through their tactile sense, therefore direct contact between doctor and patient is required. The problem is the doctor may not assess the lesion objectively. In this paper, a digital image analysis technique is developed to objectively determine the scaliness of the psoriasis lesion and provide the PASI scaliness score. Psoriasis lesion is modelled by a rough surface. The rough surface is created by superimposing a smooth average (curve) surface with a triangular waveform. For roughness determination, a polynomial surface fitting is used to estimate average surface followed by a subtraction between rough and average surface to give elevation surface (surface deviations). Roughness index is calculated by using average roughness equation to the height map matrix. The roughness algorithm has been tested to 444 lesion models. From roughness validation result, only 6 models can not be accepted (percentage error is greater than 10%). These errors occur due the scanned image quality. Roughness algorithm is validated for roughness measurement on abrasive papers at flat surface. The Pearson-s correlation coefficient of grade value (G) of abrasive paper and Ra is -0.9488, its shows there is a strong relation between G and Ra. The algorithm needs to be improved by surface filtering, especially to overcome a problem with noisy data.
Abstract: MOC (method of cell) is a new method of investigating
wave propagating in material with periodic microstructure, and can
reflect the effect of microstructure. Wave propagation in periodically
laminated medium consisting of linearly elastic layers can be treated
as a special application of this method. In this paper, it was used to
simulate the dynamic response of carbon-phenolic to impulsive
loading under certain boundary conditions. From the comparison
between the results obtained from this method and the exact results
based on propagator matrix theory, excellent agreement is achieved.
Conclusion can be made that the oscillation periodicity is decided by
the thickness of sub-cells. In the end, the NHDMOC method, which
permits studying stress wave propagation with one dimensional strain,
was applied to study the one-dimensional stress wave propagation. In
this paper, the ZWT nonlinear visco-elastic constitutive relationship
with 7 parameters, NHDMOC, and corresponding equations were
deduced. The equations were verified, comparing the elastic stress
wave propagation in SHPB with, respectively, the elastic and the
visco-elastic bar. Finally the dispersion and attenuation of stress wave
in SHPB with visco-elastic bar was studied.
Abstract: The rate of production of main products of the Fischer-Tropsch reactions over Fe/HZSM5 bifunctional catalyst in a fixed bed reactor is investigated at a broad range of temperature, pressure, space velocity, H2/CO feed molar ratio and CO2, CH4 and water flow rates. Model discrimination and parameter estimation were performed according to the integral method of kinetic analysis. Due to lack of mechanism development for Fisher – Tropsch Synthesis on bifunctional catalysts, 26 different models were tested and the best model is selected. Comprehensive one and two dimensional heterogeneous reactor models are developed to simulate the performance of fixed-bed Fischer – Tropsch reactors. To reduce computational time for optimization purposes, an Artificial Feed Forward Neural Network (AFFNN) has been used to describe intra particle mass and heat transfer diffusion in the catalyst pellet. It is seen that products' reaction rates have direct relation with H2 partial pressure and reverse relation with CO partial pressure. The results show that the hybrid model has good agreement with rigorous mechanistic model, favoring that the hybrid model is about 25-30 times faster.
Abstract: An experiment was performed with a 24.5 MeV 14N
beam on a 12C target in the cyclotron DC-60 located in Astana,
Kazakhstan, to study the elastic scattering of 14N on 12C; the
scattering was also analyzed at different energies for tracking the
phenomenon of remarkable structure at large angles. Its aims were to
extend the measurements to very large angles, and attempt to
uniquely identify the elastic scattering potential. Good agreement
between the theoretical and experimental data has been obtained with
suitable optical potential parameters. Optical model calculations with
l -dependent imaginary potentials were also applied to the data and
relatively good agreement was found.
Abstract: Composting is the process in which municipal solid
waste (MSW) and other organic waste materials such as biosolids
and manures are decomposed through the action of bacteria and other
microorganisms into a stable granular material which, applied to
land, as soil conditioner. Microorganisms, especially those that are
able to degrade polymeric organic material have a key role in speed
up this process. The aim of this study has been established to
isolation of microorganisms with high ability to production
extracellular enzymes for degradation of natural polymers that are
exists in MSW for decreasing time of degradation phase. Our
experimental study for isolation designed in two phases: in first
phase we isolated degrading microorganism with selected media that
consist a special natural polymer such as cellulose, starch, lipids and
etc as sole source of carbon. In second phase we selected
microorganism that had high degrading enzyme production with
enzymatic assay for seed production. However, our findings in pilot
scale have indicated that usage of this microbial consortium had high
efficiency for decreasing degradation phase.
Abstract: all of religions free towards society in Kazakhstan. Considering that Islam is more widespread religion in the region, Islamic industry is developing sector of Economy. There are some new sectors of Halal (Islamic) industry, which have importance for state developing on the whole. One of the youngest sectors of Halal industry is Islamic tourism, which became an object of disputes and led to dilemma, such as Islamic tourism is a result of a Religious revival and Islamic tourism is a new trend of Tourism. The paper was written under the research project “Islam in modern Kazakhstan: the nature and outcome of the religious revival".
Abstract: In recent years, a new numerical method has been
developed, the extended finite element method (X-FEM). The
objective of this work is to exploit the (X-FEM) for the treatment of
the fracture mechanics problems on 3D geometries, where we
showed the ability of this method to simulate the fatigue crack
growth into two cases: edge and central crack. In the results we
compared the six first natural frequencies of mode shapes uncracking
with the cracking initiation in the structure, and showed the stress
intensity factor (SIF) evolution function as crack size propagation
into structure, the analytical validation of (SIF) is presented. For to
evidence the aspects of this method, all result is compared between
FEA and X-FEM.
Abstract: This paper studies a vital issue in wireless
communications, which is the transmission of images over Wireless
Personal Area Networks (WPANs) through the Bluetooth network. It
presents a simple method to improve the efficiency of error control
code of old Bluetooth versions over mobile WPANs through
Interleaved Error Control Code (IECC) technique. The encoded
packets are interleaved by simple block interleaver. Also, the paper
presents a chaotic interleaving scheme as a tool against bursts of
errors which depends on the chaotic Baker map. Also, the paper
proposes using the chaotic interleaver instead of traditional block
interleaver with Forward Error Control (FEC) scheme. A comparison
study between the proposed and standard techniques for image
transmission over a correlated fading channel is presented.
Simulation results reveal the superiority of the proposed chaotic
interleaving scheme to other schemes. Also, the superiority of FEC
with proposed chaotic interleaver to the conventional interleavers
with enhancing the security level with chaotic interleaving packetby-
packet basis.
Abstract: A new generation of manufacturing machines
so-called MIMCA (modular and integrated machine control
architecture) capable of handling much increased complexity in
manufacturing control-systems is presented. Requirement for more
flexible and effective control systems for manufacturing machine
systems is investigated and dimensioned-which highlights a need for
improved means of coordinating and monitoring production
machinery and equipment used to- transport material. The MIMCA
supports simulation based on machine modeling, was conceived by
the authors to address the issues. Essentially MIMCA comprises an
organized unification of selected architectural frameworks and
modeling methods, which include: NISTRCS, UMC and Colored
Timed Petri nets (CTPN). The unification has been achieved; to
support the design and construction of hierarchical and distributed
machine control which realized the concurrent operation of reusable
and distributed machine control components; ability to handle
growing complexity; and support requirements for real- time control
systems. Thus MIMCA enables mapping between 'what a machine
should do' and 'how the machine does it' in a well-defined but
flexible way designed to facilitate reconfiguration of machine
systems.
Abstract: Ultrastructure of duodenum mucosa of irradiated rat
was studied versus dose rate of irradiation following exposure to
gamma rays from 60-Cobalt source. The animals were whole body
irradiated at two dose rates (1 Gy.mn-1 and 1 Gy.h-1) and three total
doses (1, 2 or 4 Gy) for each dose rate. 24 or 48 h after irradiation,
their small intestine was removed and samples of duodenum were
processed for observations under a transmission electron microscopy.
Samples of duodenum mucosa of control rats were processed in the
same way. For the lower dose rate of 1 Gy.h-1, main lesions
characteristic of apoptosis were detected within irradiated enterocytes
at a total dose of 2 Gy and 24 h after exposure. Necrosis was noted in
the samples, 48 h after exposition. For the higher dose rate of 1
Gy.mn-1, fewer changes were detected at all total doses 24 or 48 h
irradiation. Thus, it was shown that the appearance of radiationinduced
alterations varies not only with increasing total dose and
post-irradiation time but especially with decreasing dose rate.
Abstract: High performance Resistive Random Access Memory
(RRAM) based on HfOx has been prepared and its temperature
instability has been investigated in this work. With increasing
temperature, it is found that: leakage current at high resistance state
increases, which can be explained by the higher density of traps
inside dielectrics (related to trap-assistant tunneling), leading to a
smaller On/Off ratio; set and reset voltages decrease, which may be
attributed to the higher oxygen ion mobility, in addition to the
reduced potential barrier to create / recover oxygen ions (or oxygen
vacancies); temperature impact on the RRAM retention degradation
is more serious than electrical bias.
Abstract: Transmission network expansion planning (TNEP) is a basic part of power system planning that determines where, when and how many new transmission lines should be added to the network. Up till now, various methods have been presented to solve the static transmission network expansion planning (STNEP) problem. But in all of these methods, lines adequacy rate has not been considered at the end of planning horizon, i.e., expanded network misses adequacy after some times and needs to be expanded again. In this paper, expansion planning has been implemented by merging lines loading parameter in the STNEP and inserting investment cost into the fitness function constraints using genetic algorithm. Expanded network will possess a maximum adequacy to provide load demand and also the transmission lines overloaded later. Finally, adequacy index could be defined and used to compare some designs that have different investment costs and adequacy rates. In this paper, the proposed idea has been tested on the Garvers network. The results show that the network will possess maximum efficiency economically.
Abstract: Nowadays, manufacturers are facing great challenges
with regard to the production of green products due to the emerging issue of hazardous substance management (HSM). In particular,
environmental legislation pressures have yielded to increased risk,
manufacturing complexity and green components demands. The green principles were expanded to many departments within
organization, including supply chain. Green supply chain
management (GSCM) was emerging in the last few years. This idea
covers every stage in manufacturing from the first to the last stage of
life cycle. From product lifecycle concept, the cycle starts at the design of a product. QFD is a customer-driven product development
tool, considered as a structured management approach for efficiently
translating customer needs into design requirements and parts deployment, as well as manufacturing plans and controls in order to
achieve higher customer satisfaction. This paper develops an Eco-
QFD to provide a framework for designing Eco-mobile phone by integrating the life cycle analysis LCA into QFD throughout the entire product development process.
Abstract: Changing technology and increased constituent
demand for government services derive the need for governmental
responsiveness. The government organisations in the developing
countries will be under increased pressure to change their
bureaucratic systems to be able to respond rapidly to changing and
increasing requirements and rapid technology advancements. This
paper aims to present a conceptual framework for explaining the
main barriers and drivers of public e-service development. Therefore,
the framework provides a basic context within which the process and
practice of E-Service can be implemented successfully in the public
sector organisations. The framework is flexible enough to be adopted
by governments at different levels; national or local by developing
countries around the world.
Abstract: In this paper, Fabless Prototyping Methodology is
introduced for the design and analysis of MEMS devices.
Conventionally Finite Element Analysis (FEA) is performed before
system level simulation. In our proposed methodology, system level
simulation is performed earlier than FEA as it is computationally less
extensive and low cost. System level simulations are based on
equivalent behavioral models of MEMS device. Electrostatic
actuation based MEMS Microgripper is chosen as case study to
implement this methodology. This paper addresses the behavioral
model development and simulation of actuator part of an
electrostatically actuated Microgripper. Simulation results show that
the actuator part of Microgripper works efficiently for a voltage range
of 0-45V with the corresponding jaw displacement of 0-4.5425μm.
With some minor changes in design, this range can be enhanced to
15μm at 85V.
Abstract: Horizontal continuous casting is widely used to
produce semi-finished non-Ferrous products. Homogeneity in the
metallurgical characteristics and mechanical properties for this
product is vital for industrial application. In the present work, the
microstructure and mechanical properties of a horizontal continuous
cast two-phase brass billet have been studied. Impact strength and
hardness variations were examined and the phase composition and
porosity studied with image analysis software. Distinct differences in
mechanical properties were observed between the upper, middle and
lower parts of the billet, which are explained in terms of the
morphology and size of the phase in the microstructure. Hardness
variation in the length of billet is higher in upper area but impact
strength is higher in lower areas.
Abstract: In this study, we present an advanced detection
technique for mass type breast cancer based on texture information
of organs. The proposed method detects the cancer areas in three
stages. In the first stage, the midpoints of mass area are determined
based on AHE (Adaptive Histogram Equalization). In the second
stage, we set the threshold coefficient of homogeneity by using
MLE (Maximum Likelihood Estimation) to compute the uniformity
of texture. Finally, mass type cancer tissues are extracted from the
original image. As a result, it was observed that the proposed
method shows an improved detection performance on dense breast
tissues of Korean women compared with the existing methods. It is
expected that the proposed method may provide additional
diagnostic information for detection of mass-type breast cancer.