Abstract: In this study, active tendons with Proportional Integral
Derivation type controllers were applied to a SDOF and a MDOF
building model. Physical models of buildings were constituted with
virtual springs, dampers and rigid masses. After that, equations of
motion of all degrees of freedoms were obtained. Matlab Simulink
was utilized to obtain the block diagrams for these equations of
motion. Parameters for controller actions were found by using a trial
method. After earthquake acceleration data were applied to the
systems, building characteristics such as displacements, velocities,
accelerations and transfer functions were analyzed for all degrees of
freedoms. Comparisons on displacement vs. time, velocity vs. time,
acceleration vs. time and transfer function (Db) vs. frequency (Hz)
were made for uncontrolled and controlled buildings. The results
show that the method seems feasible.
Abstract: The effects of down slope steepness on soil splash distribution under a water drop impact have been investigated in this study. The equipment used are the burette to simulate a water drop, a splash cup filled with sandy soil which forms the source area and a splash board to collect the ejected particles. The results found in this study have shown that the apparent mass increased with increasing downslope angle following a linear regression equation with high coefficient of determination. In the same way, the radial soil splash distribution over the distance has been analyzed statistically, and an exponential function was the best fit of the relationship for the different slope angles. The curves and the regressions equations validate the well known FSDF and extend the theory of Van Dijk.
Abstract: Text-based game is supposed to be a low resource
consumption application that delivers good performances when
compared to graphical-intensive type of games. But, nowadays, some
of the online text-based games are not offering performances that are
acceptable to the users. Therefore, an online text-based game called
Star_Quest has been developed in order to analyze its behavior under
different performance measurements. Performance metrics such as
throughput, scalability, response time and page loading time are
captured to yield the performance of the game. The techniques in
performing the load testing are also disclosed to exhibit the viability
of our work. The comparative assessment between the results
obtained and the accepted level of performances are conducted as to
determine the performance level of the game. The study reveals that
the developed game managed to meet all the performance objectives
set forth.
Abstract: This article discusses the customs and traditions in
Turkestan in the late XIXth and early XXth centuries. Having a long
history, Turkestan is well-known as the birthplace of many nations
and nationalities. The name of Turkestan is also given to it for a
reason - the land of the Turkic peoples who inhabited Central Asia
and united under together. Currently, nations and nationalities of the
Turkestan region formed their own sovereign states, and every year
they prove their country names in the world community. Political,
economic importance of Turkestan, which became the gold wire
between Asia and Europe was always very high. So systematically
various aggressive actions were made by several great powers. As a
result of expansionary policy of colonization of the Russian Empire -
the Turkestan has appeared.
Abstract: A mobile agent is a software which performs an
action autonomously and independently as a person or an
organizations assistance. Mobile agents are used for searching
information, retrieval information, filtering, intruder recognition in
networks, and so on. One of the important issues of mobile agent is
their security. It must consider different security issues in effective
and secured usage of mobile agent. One of those issues is the
integrity-s protection of mobile agents.
In this paper, the advantages and disadvantages of each method,
after reviewing the existing methods, is examined. Regarding to this
matter that each method has its own advantage or disadvantage, it
seems that by combining these methods, one can reach to a better
method for protecting the integrity of mobile agents. Therefore, this
method is provided in this paper and then is evaluated in terms of
existing method. Finally, this method is simulated and its results are
the sign of improving the possibility of integrity-s protection of
mobile agents.
Abstract: Decentralized eco-sanitation system is a promising and sustainable mode comparing to the century-old centralized conventional sanitation system. The decentralized concept relies on an environmentally and economically sound management of water, nutrient and energy fluxes. Source-separation systems for urban waste management collect different solid waste and wastewater streams separately to facilitate the recovery of valuable resources from wastewater (energy, nutrients). A resource recovery centre constituted for 20,000 people will act as the functional unit for the treatment of urban waste of a high-density population community, like Singapore. The decentralized system includes urine treatment, faeces and food waste co-digestion, and horticultural waste and organic fraction of municipal solid waste treatment in composting plants. A design model is developed to estimate the input and output in terms of materials and energy. The inputs of urine (yellow water, YW) and faeces (brown water, BW) are calculated by considering the daily mean production of urine and faeces by humans and the water consumption of no-mix vacuum toilet (0.2 and 1 L flushing water for urine and faeces, respectively). The food waste (FW) production is estimated to be 150 g wet weight/person/day. The YW is collected and discharged by gravity into tank. It was found that two days are required for urine hydrolysis and struvite precipitation. The maximum nitrogen (N) and phosphorus (P) recovery are 150-266 kg/day and 20-70 kg/day, respectively. In contrast, BW and FW are mixed for co-digestion in a thermophilic acidification tank and later a decentralized/centralized methanogenic reactor is used for biogas production. It is determined that 6.16-15.67 m3/h methane is produced which is equivalent to 0.07-0.19 kWh/ca/day. The digestion residues are treated with horticultural waste and organic fraction of municipal waste in co-composting plants.
Abstract: This paper provides an analysis of corporate income
tax (CIT) incentives in the Western Balkan countries: Slovenia,
Croatia, Serbia, Montenegro, Macedonia and Albania. Western
Balkan countries, as other transition and developing countries, use
large number of the corporate income tax incentives (CIT) to attract
foreign investments and to stimulate economic activity. The main
goal of this paper is to investigate how often these countries use CIT
incentives and provide review of existing tax incentives in Western
Balkan countries. Paper will focus on reduced CIT rates, tax
holidays, and other investment incentives which imply incentives
like accelerated depreciation, tax allowances and tax credits.
Abstract: Thermoelastic temperature, displacement, and
stress in heat transfer during laser surface hardening are solved
in Eulerian formulation. In Eulerian formulations the heat flux
is fixed in space and the workpiece is moved through a control
volume. In the case of uniform velocity and uniform heat flux
distribution, the Eulerian formulations leads to a steady-state
problem, while the Lagrangian formulations remains transient.
In Eulerian formulations the reduction to a steady-state
problem increases the computational efficiency. In this study
also an analytical solution is developed for an uncoupled
transient heat conduction equation in which a plane slab is
heated by a laser beam. The thermal result of the numerical
model is compared with the result of this analytical model.
Comparing the results shows numerical solution for uncoupled
equations are in good agreement with the analytical solution.
Abstract: In this study, a new and fast algorithm for Ascending
Aorta (AscA) and Descending Aorta (DesA) segmentation is
presented using Computed Tomography Angiography images. This
process is quite important especially at the detection of aortic
plaques, aneurysms, calcification or stenosis. The applied method has
been carried out at four steps. At first step, lung segmentation is
achieved. At the second one, Mediastinum Region (MR) is detected
to use in the segmentation. At the third one, images have been
applied optimal threshold and components which are outside of the
MR were removed. Lastly, identifying and segmentation of AscA and
DesA have been carried out. The performance of the applied method
is found quite well for radiologists and it gives enough results to the
surgeries medically.
Abstract: Nowadays, OCR systems have got several
applications and are increasingly employed in daily life. Much
research has been done regarding the identification of Latin,
Japanese, and Chinese characters. However, very little investigation
has been performed regarding Farsi/Arabic characters recognition.
Probably the reason is difficulty and complexity of those characters
identification compared to the others and limitation of IT activities in
Farsi and Arabic speaking countries. In this paper, a technique has
been employed to identify isolated Farsi/Arabic characters. A chain
code based algorithm along with other significant peculiarities such
as number and location of dots and auxiliary parts, and the number of
holes existing in the isolated character has been used in this study to
identify Farsi/Arabic characters. Experimental results show the
relatively high accuracy of the method developed when it is tested on
several standard Farsi fonts.
Abstract: In this work, the plate bending formulation of the boundary element method - BEM, based on the Reissner?s hypothesis, is extended to the analysis of plates reinforced by beams taking into account the membrane effects. The formulation is derived by assuming a zoned body where each sub-region defines a beam or a slab and all of them are represented by a chosen reference surface. Equilibrium and compatibility conditions are automatically imposed by the integral equations, which treat this composed structure as a single body. In order to reduce the number of degrees of freedom, the problem values defined on the interfaces are written in terms of their values on the beam axis. Initially are derived separated equations for the bending and stretching problems, but in the final system of equations the two problems are coupled and can not be treated separately. Finally are presented some numerical examples whose analytical results are known to show the accuracy of the proposed model.
Abstract: The use of artificial neural network (ANN) modeling
for prediction and forecasting variables in water resources
engineering are being increasing rapidly. Infrastructural applications
of ANN in terms of selection of inputs, architecture of networks,
training algorithms, and selection of training parameters in different
types of neural networks used in water resources engineering have
been reported. ANN modeling conducted for water resources
engineering variables (river sediment and discharge) published in
high impact journals since 2002 to 2011 have been examined and
presented in this review. ANN is a vigorous technique to develop
immense relationship between the input and output variables, and
able to extract complex behavior between the water resources
variables such as river sediment and discharge. It can produce robust
prediction results for many of the water resources engineering
problems by appropriate learning from a set of examples. It is
important to have a good understanding of the input and output
variables from a statistical analysis of the data before network
modeling, which can facilitate to design an efficient network. An
appropriate training based ANN model is able to adopt the physical
understanding between the variables and may generate more effective
results than conventional prediction techniques.
Abstract: In this study, we explore the use of information for inventory decision in the healthcare organization (HO). We consider the scenario when the HO can make use of the information collected from some correlated products to enhance its inventory planning. Motivated by our real world observations that HOs adopt RFID and bar-coding system for information collection purpose, we examine the effectiveness of these systems for inventory planning with Bayesian information updating. We derive the optimal ordering decision and study the issue of Pareto improvement in the supply chain. Our analysis demonstrates that RFID system will outperform the bar-coding system when the RFID system installation cost and the tag cost reduce to a level that is comparable with that of the barcoding system. We also show how an appropriately set wholesale pricing contract can achieve Pareto improvement in the HO supply chain.
Abstract: Design of a fixed parameter robust STATCOM controller for a multi-machine power system through an H-? based loop-shaping procedure is presented. The trial and error part of the graphical loop-shaping procedure has been eliminated by embedding a particle swarm optimization (PSO) technique in the design loop. Robust controllers were designed considering the detailed dynamics of the multi-machine system and results were compared with reduced order models. The robust strategy employing loop-shaping and PSO algorithms was observed to provide very good damping profile for a wide range of operation and for various disturbance conditions.
Abstract: A research program is conducted to evaluate the
mechanical properties of Ultra High Performance Concrete, target
compressive strength at the age of 28 days being more than 150 MPa.
The methodology to develop such mix has been explained. The
material properties, mix design and curing regime are determined.
The material attributes are understood by studying the stress strain
behaviour of UHPC cylinders under uniaxial compressive loading.
The load –crack mouth opening displacement (cmod) of UHPC
beams, flexural strength and fracture energy was evaluated using
third point loading test. Compressive strength and Split tensile
strength results are determined to find out the compressive and tensile
behaviour. Residual strength parameters are presented vividly
explaining the flexural performance, toughness of concrete.Durability
studies were also done to compare the effect of fibre to that of a
control mix For all the studies the Mechanical properties were
evaluated by varying the percentage and aspect ratio of steel fibres
The results reflected that higher aspect ratio and fibre volume
produced drastic changes in the cube strength, cylinder strength, post
peak response, load-cmod, fracture energy flexural strength, split
tensile strength, residual strength and durability. In regards to null
application of UHPC in India, an initiative is undertaken to
comprehend the mechanical behaviour of UHPC, which will be vital
for longer run in commercialization for structural applications.
Abstract: Dengue is a mosquito-borne infection that has peaked to an alarming rate in recent decades. It can be found in tropical and sub-tropical climate. In Malaysia, dengue has been declared as one of the national health threat to the public. This study aimed to map the spatial distributions of dengue cases in the district of Hulu Langat, Selangor via a combination of Geographic Information System (GIS) and spatial statistic tools. Data related to dengue was gathered from the various government health agencies. The location of dengue cases was geocoded using a handheld GPS Juno SB Trimble. A total of 197 dengue cases occurring in 2003 were used in this study. Those data then was aggregated into sub-district level and then converted into GIS format. The study also used population or demographic data as well as the boundary of Hulu Langat. To assess the spatial distribution of dengue cases three spatial statistics method (Moran-s I, average nearest neighborhood (ANN) and kernel density estimation) were applied together with spatial analysis in the GIS environment. Those three indices were used to analyze the spatial distribution and average distance of dengue incidence and to locate the hot spot of dengue cases. The results indicated that the dengue cases was clustered (p < 0.01) when analyze using Moran-s I with z scores 5.03. The results from ANN analysis showed that the average nearest neighbor ratio is less than 1 which is 0.518755 (p < 0.0001). From this result, we can expect the dengue cases pattern in Hulu Langat district is exhibiting a cluster pattern. The z-score for dengue incidence within the district is -13.0525 (p < 0.0001). It was also found that the significant spatial autocorrelation of dengue incidences occurs at an average distance of 380.81 meters (p < 0.0001). Several locations especially residential area also had been identified as the hot spots of dengue cases in the district.
Abstract: This paper presents a new approach for busbar protection with stable operation of current transformer during saturation, using fuzzy neuro and symmetrical components theory. This technique uses symmetrical components of current signals to learn the hidden relationship existing in the input patterns. Simulation studies are preformed and the influence of changing system parameters such as inception fault and source impedance is studied. Details of the design procedure and the results of performance studies with the proposed relay are given in the paper. An analysis of the performance of the proposed technique during ct saturation conditions is presented. The performance of the technique was investigated for a variety of operating conditions and for several busbar configurations. Data generated by EMTDC simulations of model power systems were used in the investigations. The results indicate that the proposed technique is stable during ct saturation conditions.
Abstract: The Muslim faith requires individuals to fast between
the hours of sunrise and sunset during the month of Ramadan. Our
recent work has concentrated on some of the changes that take place
during the daytime when fasting. A questionnaire was developed to
assess subjective estimates of physical, mental and social activities,
and fatigue. Four days were studied: in the weeks before and after
Ramadan (control days) and during the first and last weeks of
Ramadan (experimental days). On each of these four days, this
questionnaire was given several times during the daytime and once
after the fast had been broken and just before individuals retired at
night.
During Ramadan, daytime mental, physical and social activities
all decreased below control values but then increased to abovecontrol
values in the evening. The desires to perform physical and
mental activities showed very similar patterns. That is, individuals
tried to conserve energy during the daytime in preparation for the
evenings when they ate and drank, often with friends. During
Ramadan also, individuals were more fatigued in the daytime and
napped more often than on control days. This extra fatigue probably
reflected decreased sleep, individuals often having risen earlier
(before sunrise, to prepare for fasting) and retired later (to enable
recovery from the fast).
Some physiological measures and objective measures of
performance (including the response to a bout of exercise) have also
been investigated. Urine osmolality fell during the daytime on
control days as subjects drank, but rose in Ramadan to reach values
at sunset indicative of dehydration. Exercise performance was also
compromised, particularly late in the afternoon when the fast had
lasted several hours. Self-chosen exercise work-rates fell and a set
amount of exercise felt more arduous. There were also changes in
heart rate and lactate accumulation in the blood, indicative of greater
cardiovascular and metabolic stress caused by the exercise in
subjects who had been fasting. Daytime fasting in Ramadan produces
widespread effects which probably reflect combined effects of sleep
loss and restrictions to intakes of water and food.
Abstract: Computers are being integrated in the various aspects
of human every day life in different shapes and abilities. This fact
has intensified a requirement for the software development
technologies which is ability to be: 1) portable, 2) adaptable, and 3)
simple to develop. This problem is also known as the Pervasive
Computing Problem (PCP) which can be implemented in different
ways, each has its own pros and cons and Context Oriented
Programming (COP) is one of the methods to address the PCP.
In this paper a design for a COP framework, a context aware
framework, is presented which has eliminated weak points of a
previous design based on interpreter languages, while introducing the
compiler languages power in implementing these frameworks.
The key point of this improvement is combining COP and
Dependency Injection (DI) techniques. Both old and new frameworks
are analyzed to show advantages and disadvantages. Finally a
simulation of both designs is proposed to indicating that the practical
results agree with the theoretical analysis while the new design runs
almost 8 times faster.
Abstract: Refractive index control of benzocyclobutene (BCB 4024-40) is achieved by facilitating different conditions during the thermal curing of BCB film. Refractive index (RI) change of 1.49% is obtained with curing of BCB film using an oven, while the RI change is 0.1% when the BCB is cured using a hotplate. The two different curing methods exhibit a temperature dependent refractive index change of the BCB photosensitive polymer. By carefully controlling the curing conditions, multiple layers of BCB with different RI can be fabricated, which can then be applied in the fabrication of optical waveguides.