Abstract: This paper presents the design of a ring-shaped tri-axial fore sensor that can be incorporated into the tip of a guidewire for use in minimally invasive surgery (MIS). The designed sensor comprises a ring-shaped structure located at the center of four cantilever beams. The ringdesign allows surgical tools to be easily passed through which largely simplified the integration process. Silicon nanowires (SiNWs) are used aspiezoresistive sensing elementsembeddedon the four cantilevers of the sensor to detect the resistance change caused by the applied load.An integration scheme with new designed guidewire tip structure having two coils at the distal end is presented. Finite element modeling has been employed in the sensor design to find the maximum stress location in order to put the SiNWs at the high stress regions to obtain maximum output. A maximum applicable force of 5 mN is found from modeling. The interaction mechanism between the designed sensor and a steel wire has been modeled by FEM. A linear relationship between the applied load on the steel wire and the induced stress on the SiNWs were observed.
Abstract: A specially designed flat plate was mounted vertically
over the axial line in the wind tunnel of the Aerospace Department of
the Pusan National University. The plate is 2 m long, 0.8 m high and 8
cm thick. The measurements were performed in velocity range from
15 to 60 m/s. A sand paper turbulizer was placed close to the plate nose
to provide fully developed turbulent boundary layer over the most part
of the plate. Strain balances were mounted in the trailing part of the
plate to measure the skin friction drag over removable insertions of
0.55×0.25m2 size. A set of the insertions was designed and
manufactured: 3mm thick polished metal surface and three compliant
surfaces. The compliant surfaces were manufactured of a silicone
rubber Silastic® S2 (Dow Corning company). To modify the
viscoelastic properties of the rubber, its composition was varied: 90%
of the rubber + 10% catalyst (standard), 92.5% + 7.5% (weak), 85% +
15% (strong). Modulus of elasticity and the loss tangent were
measured accurately for these materials in the frequency range from
40 Hz to 3 KHz using the unique proposed technique.
Abstract: A wireless sensor network with a large number of tiny sensor nodes can be used as an effective tool for gathering data in various situations. One of the major issues in wireless sensor networks is developing an energy-efficient routing protocol which has a significant impact on the overall lifetime of the sensor network. In this paper, we propose a novel hierarchical with static clustering routing protocol called Energy-Efficient Protocol with Static Clustering (EEPSC). EEPSC, partitions the network into static clusters, eliminates the overhead of dynamic clustering and utilizes temporary-cluster-heads to distribute the energy load among high-power sensor nodes; thus extends network lifetime. We have conducted simulation-based evaluations to compare the performance of EEPSC against Low-Energy Adaptive Clustering Hierarchy (LEACH). Our experiment results show that EEPSC outperforms LEACH in terms of network lifetime and power consumption minimization.
Abstract: In real-time networks a large number of application programs are relying on video data and heterogeneous data transmission techniques. The aim of this research is presenting a method for end-to-end vouch quality service in surface applicationlayer for sending video data in comparison form in wireless heterogeneous networks. This method tries to improve the video sending over the wireless heterogeneous networks with used techniques in surface layer, link and application. The offered method is showing a considerable improvement in quality observing by user. In addition to this, other specifications such as shortage of data load that had require to resending and limited the relation period length to require time for second data sending, help to be used the offered method in the wireless devices that have a limited energy. The presented method and the achieved improvement is simulated and presented in the NS-2 software.
Abstract: Delay and Disruption Tolerant Networking is part of
the Inter Planetary Internet with primary application being Deep
Space Networks. Its Terrestrial form has interesting research
applications such as Alagappa University Delay Tolerant Water
Monitoring Network which doubles as test beds for improvising its
routing scheme. DTNs depend on node mobility to deliver packets
using a store-carry-and forward paradigm. Throwboxes are small and
inexpensive stationary devices equipped with wireless interfaces and
storage. We propose the use of Throwboxes to enhance the contact
opportunities of the nodes and hence improve the Throughput. The
enhancement is evaluated using Alunivdtnsim, a desktop simulator in
C language and the results are graphically presented.
Abstract: In a wireless communication system, a
predistorter(PD) is often employed to alleviate nonlinear distortions
due to operating a power amplifier near saturation, thereby improving
the system performance and reducing the interference to adjacent
channels. This paper presents a new adaptive polynomial digital
predistorter(DPD). The proposed DPD uses Coordinate Rotation
Digital Computing(CORDIC) processors and PD process by pipelined
architecture. It is simpler and faster than conventional adaptive
polynomial DPD. The performance of the proposed DPD is proved by
MATLAB simulation.
Abstract: In this study, we propose a network architecture for
providing secure access to information resources of enterprise
network from remote locations in a wireless fashion. Our proposed
architecture offers a very promising solution for organizations which
are in need of a secure, flexible and cost-effective remote access
methodology. Security of the proposed architecture is based on
Virtual Private Network technology and a special role based access
control mechanism with location and time constraints. The flexibility
mainly comes from the use of Internet as the communication medium
and cost-effectiveness is due to the possibility of in-house
implementation of the proposed architecture.
Abstract: In this paper, an adaptive radio resource allocation
(RRA) algorithm applying to multiple traffic OFDMA system is
proposed, which distributes sub-carrier and loading bits among users
according to their different QoS requirements and traffic class. By
classifying and prioritizing the users based on their traffic
characteristic and ensuring resource for higher priority users, the
scheme decreases tremendously the outage probability of the users
requiring a real time transmission without impact on the spectrum
efficiency of system, as well as the outage probability of data users is
not increased compared with the RRA methods published.
Abstract: Target tracking and localization are important applications
in wireless sensor networks. In these applications, sensor nodes
collectively monitor and track the movement of a target. They have
limited energy supplied by batteries, so energy efficiency is essential
for sensor networks. Most existing target tracking protocols need to
wake up sensors periodically to perform tracking. Some unnecessary
energy waste is thus introduced. In this paper, an energy efficient
protocol for target localization is proposed. In order to preserve
energy, the protocol fixes the number of sensors for target tracking,
but it retains the quality of target localization in an acceptable
level. By selecting a set of sensors for target localization, the other
sensors can sleep rather than periodically wake up to track the target.
Simulation results show that the proposed protocol saves a significant
amount of energy and also prolongs the network lifetime.
Abstract: As the increase of intraoral acidity due to ingestion of sweet foods and acidic beverages usually bring forth a dental caries and a erosion, the measurement of intraoral pH is essential in the study of oral environment. The indwelling intraoral pH telemetry for lasting longer than 24 hours in the mouth was developed to overcome the limits of conventional wire electrode method previously used for salivary and plaque pH measurement, and to assess its effectiveness.
Abstract: Short Message Service (SMS) has grown in
popularity over the years and it has become a common way of
communication, it is a service provided through General System
for Mobile Communications (GSM) that allows users to send text
messages to others.
SMS is usually used to transport unclassified information, but
with the rise of mobile commerce it has become a popular tool for
transmitting sensitive information between the business and its
clients. By default SMS does not guarantee confidentiality and
integrity to the message content.
In the mobile communication systems, security (encryption)
offered by the network operator only applies on the wireless link.
Data delivered through the mobile core network may not be
protected. Existing end-to-end security mechanisms are provided
at application level and typically based on public key
cryptosystem.
The main concern in a public-key setting is the authenticity of
the public key; this issue can be resolved by identity-based (IDbased)
cryptography where the public key of a user can be derived
from public information that uniquely identifies the user.
This paper presents an encryption mechanism based on the IDbased
scheme using Elliptic curves to provide end-to-end security
for SMS. This mechanism has been implemented over the standard
SMS network architecture and the encryption overhead has been
estimated and compared with RSA scheme. This study indicates
that the ID-based mechanism has advantages over the RSA
mechanism in key distribution and scalability of increasing
security level for mobile service.
Abstract: Wireless Sensor Networks (WSNs) are wireless
networks consisting of number of tiny, low cost and low power
sensor nodes to monitor various physical phenomena like
temperature, pressure, vibration, landslide detection, presence of any
object, etc. The major limitation in these networks is the use of nonrechargeable
battery having limited power supply. The main cause of
energy consumption WSN is communication subsystem. This paper
presents an efficient grid formation/clustering strategy known as Grid
based level Clustering and Aggregation of Data (GCAD). The
proposed clustering strategy is simple and scalable that uses low duty
cycle approach to keep non-CH nodes into sleep mode thus reducing
energy consumption. Simulation results demonstrate that our
proposed GCAD protocol performs better in various performance
metrics.
Abstract: In this paper electrical characteristics of various kinds
of multiple-gate silicon nanowire transistors (SNWT) with the
channel length equal to 7 nm are compared. A fully ballistic quantum
mechanical transport approach based on NEGF was employed to
analyses electrical characteristics of rectangular and cylindrical
silicon nanowire transistors as well as a Double gate MOS FET. A
double gate, triple gate, and gate all around nano wires were studied
to investigate the impact of increasing the number of gates on the
control of the short channel effect which is important in nanoscale
devices. Also in the case of triple gate rectangular SNWT inserting
extra gates on the bottom of device can improve the application of
device. The results indicate that by using gate all around structures
short channel effects such as DIBL, subthreshold swing and delay
reduces.
Abstract: This article discusses the customs and traditions in
Turkestan in the late XIXth and early XXth centuries. Having a long
history, Turkestan is well-known as the birthplace of many nations
and nationalities. The name of Turkestan is also given to it for a
reason - the land of the Turkic peoples who inhabited Central Asia
and united under together. Currently, nations and nationalities of the
Turkestan region formed their own sovereign states, and every year
they prove their country names in the world community. Political,
economic importance of Turkestan, which became the gold wire
between Asia and Europe was always very high. So systematically
various aggressive actions were made by several great powers. As a
result of expansionary policy of colonization of the Russian Empire -
the Turkestan has appeared.
Abstract: Using mini modules of Tmotes, it is possible to automate a small personal area network. This idea can be extended to large networks too by implementing multi-hop routing. Linking the various Tmotes using Programming languages like Nesc, Java and having transmitter and receiver sections, a network can be monitored. It is foreseen that, depending on the application, a long range at a low data transfer rate or average throughput may be an acceptable trade-off. To reduce the overall costs involved, an optimum number of Tmotes to be used under various conditions (Indoor/Outdoor) is to be deduced. By analyzing the data rates or throughputs at various locations of Tmotes, it is possible to deduce an optimal number of Tmotes for a specific network. This paper deals with the determination of optimum distances to reduce the cost and increase the reliability of the entire sensor network with Wireless Local Loop (WLL) capability.
Abstract: Recently, as information industry and mobile
communication technology are developing, this study is conducted on
the new concept of intelligent structures and maintenance techniques
that applied wireless sensor network, USN (Ubiquitous Sensor
Network), to social infrastructures such as civil and architectural
structures on the basis of the concept of Ubiquitous Computing that
invisibly provides human life with computing, along with mutually
cooperating, compromising and connecting networks each other by
having computers within all objects around us.
Therefore, the purpose of this study is to investigate the capability
of wireless communication of sensor node embedded in reinforced
concrete structure with a basic experiment on an electric wave
permeability of sensor node by fabricating molding with variables of
concrete thickness and steel bars that are mostly used in constructing
structures to determine the feasibility of application to constructing
structures with USN.
At this time, with putting the pitches of steel bars, the thickness of
concrete placed, and the intensity of RF signal of a
transmitter-receiver as variables and when wireless communication
module was installed inside, the possible communication distance of
plain concrete and the possible communication distance by the pitches
of steel bars was measured in the horizontal and vertical direction
respectively. Besides, for the precise measurement of diminution of an
electric wave, the magnitude of an electric wave in the range of used
frequencies was measured by using Spectrum Analyzer. The
phenomenon of diminution of an electric wave was numerically
analyzed and the effect of the length of wavelength of frequencies was
analyzed by the properties of a frequency band area.
As a result of studying the feasibility of an application to
constructing structures with wireless sensor, in case of plain concrete,
it shows 45cm for the depth of permeability and in case of reinforced
concrete with the pitches of 5cm, it shows 37cm and 45cm for the
pitches of 15cm.
Abstract: DS-CDMA system is well known wireless
technology. This system suffers from MAI (Multiple Access
Interference) caused by Direct Sequence users. Multi-User Detection
schemes were introduced to detect the users- data in presence of
MAI. This paper focuses on linear multi-user detection schemes used
for data demodulation. Simulation results depict the performance of
three detectors viz-conventional detector, Decorrelating detector and
Subspace MMSE (Minimum Mean Square Error) detector. It is seen
that the performance of these detectors depends on the number of
paths and the length of Gold code used.
Abstract: The prologue of new High Voltage (HV) transmission
mains into the community necessitates earthing design to ensure
safety compliance of the system. Conductive structures such as steel
or concrete poles are widely used in HV transmission mains. The
earth potential rise (EPR) generated by a fault on these structures
could result to an unsafe condition. This paper discusses information
on the input impedance of the over head earth wire (OHEW) system
for finite and infinite transmission mains. The definition of finite and
infinite system is discussed, maximum EPR due to pole fault. The
simplified equations for EPR assessments are introduced and
discussed for the finite and infinite conditions. A case study is also
shown.
Abstract: In this paper, we present an analytical framework for the evaluation of the uplink performance of multihop cellular networks based on dynamic time division duplex (TDD). New wireless broadband protocols, such as WiMAX, WiBro, and 3G-LTE apply TDD, and mobile communication protocols under standardization (e.g., IEEE802.16j) are investigating mobile multihop relay (MMR) as a future technology. In this paper a novel MMR TDD scheme is presented, where the dynamic range of the frame is shared to traffic resources of asymmetric nature and multihop relaying. The mobile communication channel interference model comprises of inner and co-channel interference (CCI). The performance analysis focuses on the uplink due to the fact that the effects of dynamic resource allocation show significant performance degradation only in the uplink compared to time division multiple access (TDMA) schemes due to CCI [1-3], where the downlink results to be the same or better.The analysis was based on the signal to interference power ratio (SIR) outage probability of dynamic TDD (D-TDD) and TDMA systems,which are the most widespread mobile communication multi-user control techniques. This paper presents the uplink SIR outage probability with multihop results and shows that the dynamic TDD scheme applying MMR can provide a performance improvement compared to single hop applications if executed properly.
Abstract: Routing places an important role in determining the
quality of service in wireless networks. The routing methods adopted
in wireless networks have many drawbacks. This paper aims to
review the current routing methods used in wireless networks. This
paper proposes an innovative solution to overcome the problems in
routing. This solution is aimed at improving the Quality of Service.
This solution is different from others as it involves the resuage of the
part of the virtual circuits. This improvement in quality of service is
important especially in propagation of multimedia applications like
video, animations etc. So it is the dire need to propose a new solution
to improve the quality of service in ATM wireless networks for
multimedia applications especially during this era of multimedia
based applications.