Abstract: Energy consumption rate during the cooling process
of industrial glass tempering process is considerably high. In this
experimental study the effect of dimensionless jet to jet distance
(S/D) and jet to plate distance (H/D) on the cooling time have been
investigated. In the experiments 4 mm thick glass samples have been
used. Cooling unit consists of 16 mutually placed seamless aluminum
nozzles of 8 mm in diameter and 80 mm in length. Nozzles were in
staggered arrangement. Experiments were conducted with circular
jets for H/D values between 1 and 10, and for S/D values between 2
and 10. During the experiments Reynolds number has been kept
constant at 30000. Experimental results showed that the longest
cooling time with 87 seconds has been observed in the experiments
for S/D=10 and H/D=10 values, while the shortest cooling time with
42.5 seconds has been measured in the experiments for S/D=2 and
H/D=4 values.
Abstract: An efficient transient flow simulation for gas
pipelines and networks is presented. The proposed transient flow
simulation is based on the transfer function models and MATLABSimulink.
The equivalent transfer functions of the nonlinear
governing equations are derived for different types of the boundary
conditions. Next, a MATLAB-Simulink library is developed and
proposed considering any boundary condition type. To verify the
accuracy and the computational efficiency of the proposed
simulation, the results obtained are compared with those of the
conventional finite difference schemes (such as TVD, method of
lines, and other finite difference implicit and explicit schemes). The
effects of the flow inertia and the pipeline inclination are
incorporated in this simulation. It is shown that the proposed
simulation has a sufficient accuracy and it is computationally more
efficient than the other methods.
Abstract: This paper presents the development and application of an adaptive neuro fuzzy inference system (ANFIS) based intelligent hybrid neuro fuzzy controller for automatic generation control (AGC) of two-area interconnected thermal power system with reheat non linearity. The dynamic response of the system has been studied for 1% step load perturbation in area-1. The performance of the proposed neuro fuzzy controller is compared against conventional proportional-integral (PI) controller, state feedback linear quadratic regulator (LQR) controller and fuzzy gain scheduled proportionalintegral (FGSPI) controller. Comparative analysis demonstrates that the proposed intelligent neuro fuzzy controller is the most effective of all in improving the transients of frequency and tie-line power deviations against small step load disturbances. Simulations have been performed using Matlab®.
Abstract: Among all mechanical joining processes, welding has
been employed for its advantage in design flexibility, cost saving,
reduced overall weight and enhanced structural performance.
However, for structures made of relatively thin components, welding
can introduce significant buckling distortion which causes loss of
dimensional control, structural integrity and increased fabrication
costs. Different parameters can affect buckling behavior of welded
thin structures such as, heat input, welding sequence, dimension of
structure. In this work, a 3-D thermo elastic-viscoplastic finite
element analysis technique is applied to evaluate the effect of shell
dimensions on buckling behavior and entropy generation of welded
thin shells. Also, in the present work, the approximated longitudinal
transient stresses which produced in each time step, is applied to the
3D-eigenvalue analysis to ratify predicted buckling time and
corresponding eigenmode. Besides, the possibility of buckling
prediction by entropy generation at each time is investigated and it is
found that one can predict time of buckling with drawing entropy
generation versus out of plane deformation. The results of finite
element analysis show that the length, span and thickness of welded
thin shells affect the number of local buckling, mode shape of global
buckling and post-buckling behavior of welded thin shells.
Abstract: A considerable progress has been achieved in transient
stability analysis (TSA) with various FACTS controllers. But, all
these controllers are associated with single transmission line. This
paper is intended to discuss a new approach i.e. a multi-line FACTS
controller which is interline power flow controller (IPFC) for TSA of
a multi-machine power system network. A mathematical model of
IPFC, termed as power injection model (PIM) presented and this
model is incorporated in Newton-Raphson (NR) power flow
algorithm. Then, the reduced admittance matrix of a multi-machine
power system network for a three phase fault without and with IPFC
is obtained which is required to draw the machine swing curves. A
general approach based on L-index has also been discussed to find
the best location of IPFC to reduce the proximity to instability of a
power system. Numerical results are carried out on two test systems
namely, 6-bus and 11-bus systems. A program in MATLAB has
been written to plot the variation of generator rotor angle and speed
difference curves without and with IPFC for TSA and also a simple
approach has been presented to evaluate critical clearing time for test
systems. The results obtained without and with IPFC are compared
and discussed.
Abstract: A novel three-phase active power filter (APF) circuit with photovoltaic (PV) system to improve the quality of service and to reduce the capacity of energy storage capacitor is presented. The energy balance concept and sampling technique were used to simplify the calculation algorithm for the required utility source current and to control the voltage of the energy storage capacitor. The feasibility was verified by using the Pspice simulations and experiments. When the APF mode was used during non-operational period, not only the utilization rate, power factor and power quality could be improved, but also the capacity of energy storage capacitor could sparing. As the results, the advantages of the APF circuit are simplicity of control circuits, low cost, and good transient response.
Abstract: Water pipe network is installed underground and once equipped, it is difficult to recognize the state of pipes when the leak or burst happens. Accordingly, post management is often delayed
after the fault occurs. Therefore, the systematic fault management system of water pipe network is required to prevent the accident and
minimize the loss. In this work, we develop online fault detection system of water pipe network using data of pipes such as flow rate
or pressure. The transient model describing water flow in pipelines
is presented and simulated using MATLAB. The fault situations such
as the leak or burst can be also simulated and flow rate or pressure data when the fault happens are collected. Faults are detected using
statistical methods of fast Fourier transform and discrete wavelet transform, and they are compared to find which method shows the
better fault detection performance.
Abstract: Fractional Fourier Transform, which is a
generalization of the classical Fourier Transform, is a powerful tool
for the analysis of transient signals. The discrete Fractional Fourier
Transform Hamiltonians have been proposed in the past with varying
degrees of correlation between their eigenvectors and Hermite
Gaussian functions. In this paper, we propose a new Hamiltonian for
the discrete Fractional Fourier Transform and show that the
eigenvectors of the proposed matrix has a higher degree of
correlation with the Hermite Gaussian functions. Also, the proposed
matrix is shown to give better Fractional Fourier responses with
various transform orders for different signals.
Abstract: This paper presents a procedure of forming the
mathematical model of radial electric power systems for simulation
of both transient and steady-state conditions. The research idea has
been based on nodal voltages technique and on differentiation of
Kirchhoff's current law (KCL) applied to each non-reference node of
the radial system, the result of which the nodal voltages has been
calculated by solving a system of algebraic equations. Currents of the
electric power system components have been determined by solving
their respective differential equations. Transforming the three-phase
coordinate system into Cartesian coordinate system in the model
decreased the overall number of equations by one third. The use of
Cartesian coordinate system does not ignore the DC component
during transient conditions, but restricts the model's implementation
for symmetrical modes of operation only. An example of the input
data for a four-bus radial electric power system has been calculated.
Abstract: A minimal complexity version of component mode
synthesis is presented that requires simplified computer
programming, but still provides adequate accuracy for modeling
lower eigenproperties of large structures and their transient
responses. The novelty is that a structural separation into components
is done along a plane/surface that exhibits rigid-like behavior, thus
only normal modes of each component is sufficient to use, without
computing any constraint, attachment, or residual-attachment modes.
The approach requires only such input information as a few (lower)
natural frequencies and corresponding undamped normal modes of
each component. A novel technique is shown for formulation of
equations of motion, where a double transformation to generalized
coordinates is employed and formulation of nonproportional damping
matrix in generalized coordinates is shown.
Abstract: In this paper a mixed method by combining an evolutionary and a conventional technique is proposed for reduction of Single Input Single Output (SISO) continuous systems into Reduced Order Model (ROM). In the conventional technique, the mixed advantages of Mihailov stability criterion and continued Fraction Expansions (CFE) technique is employed where the reduced denominator polynomial is derived using Mihailov stability criterion and the numerator is obtained by matching the quotients of the Cauer second form of Continued fraction expansions. Then, retaining the numerator polynomial, the denominator polynomial is recalculated by an evolutionary technique. In the evolutionary method, the recently proposed Differential Evolution (DE) optimization technique is employed. DE method is based on the minimization of the Integral Squared Error (ISE) between the transient responses of original higher order model and the reduced order model pertaining to a unit step input. The proposed method is illustrated through a numerical example and compared with ROM where both numerator and denominator polynomials are obtained by conventional method to show its superiority.
Abstract: This paper proposes a new performance characterization for the test strategy intended for second order filters denominated Transient Analysis Method (TRAM). We evaluate the ability of the addressed test strategy for detecting deviation faults under simultaneous statistical fluctuation of the non-faulty parameters. For this purpose, we use Monte Carlo simulations and a fault model that considers as faulty only one component of the filter under test while the others components adopt random values (within their tolerance band) obtained from their statistical distributions. The new data reported here show (for the filters under study) the presence of hard-to-test components and relatively low fault coverage values for small deviation faults. These results suggest that the fault coverage value obtained using only nominal values for the non-faulty components (the traditional evaluation of TRAM) seem to be a poor predictor of the test performance.
Abstract: Dynamic models of power converters are normally
time-varying because of their switching actions. Several approaches
are applied to analyze the power converters to achieve the timeinvariant
models suitable for system analysis and design via the
classical control theory. The paper presents how to derive dynamic
models of the power system consisting of a three-phase controlled
rectifier feeding an uncontrolled buck converter by using the
combination between the well known techniques called the DQ and
the generalized state-space averaging methods. The intensive timedomain
simulations of the exact topology model are used to support
the accuracies of the reported model. The results show that the
proposed model can provide good accuracies in both transient and
steady-state responses.
Abstract: In this study, to accurately predict cavitation of a
centrifugal pump, numerical analysis was compared with experimental
results modeled on a small industrial centrifugal pump. In this study,
numerical analysis was compared with experimental results modeled
on a small industrial centrifugal pump for reliable prediction on
cavitation of a centrifugal pump. To improve validity of the numerical
analysis, transient analysis was conducted on the calculated domain of
full-type geometry, such as an experimental apparatus. The numerical
analysis from the results was considered to be a reliable prediction of
cavitaion.
Abstract: The objective of the present paper is a numerical
analysis of the flow forces acting on spool surfaces of a pressure
regulated valve. The transient, compressible and turbulent flow
structures inside the valve are simulated using ANSYS FLUENT
coupled with a special UDF. Here, valve inlet pressure is varied in a
stepwise manner. For every value of inlet pressure, transient analysis
leads to a quasi-static flow through the valve. Spool forces are
calculated based on different pressures at inlet. From this information
of spool forces, pressure characteristic of the passive control circuit
has been derived.
Abstract: Reduction of Single Input Single Output (SISO) continuous systems into Reduced Order Model (ROM), using a conventional and an evolutionary technique is presented in this paper. In the conventional technique, the mixed advantages of Mihailov stability criterion and continued fraction expansions (CFE) technique is employed where the reduced denominator polynomial is derived using Mihailov stability criterion and the numerator is obtained by matching the quotients of the Cauer second form of Continued fraction expansions. In the evolutionary technique method Particle Swarm Optimization (PSO) is employed to reduce the higher order model. PSO method is based on the minimization of the Integral Squared Error (ISE) between the transient responses of original higher order model and the reduced order model pertaining to a unit step input. Both the methods are illustrated through numerical example.
Abstract: Fractional Fourier Transform is a powerful tool,
which is a generalization of the classical Fourier Transform. This
paper provides a mathematical relation relating the span in Fractional
Fourier domain with the amplitude and phase functions of the signal,
which is further used to study the variation of quality factor with
different values of the transform order. It is seen that with the
increase in the number of transients in the signal, the deviation of
average Fractional Fourier span from the frequency bandwidth
increases. Also, with the increase in the transient nature of the signal,
the optimum value of transform order can be estimated based on the
quality factor variation, and this value is found to be very close to
that for which one can obtain the most compact representation. With
the entire mathematical analysis and experimentation, we consolidate
the fact that Fractional Fourier Transform gives more optimal
representations for a number of transform orders than Fourier
transform.
Abstract: The paper deals with determination of electromagnetic
and temperature field distribution of induction heating system used
for pipe brazing. The problem is considered as coupled – time
harmonic electromagnetic and transient thermal field. It has been
solved using finite element method. The detailed maps of
electromagnetic and thermal field distribution have been obtained.
The good understanding of the processes in the considered system
ensures possibilities for control, management and increasing the
efficiency of the welding process.
Abstract: In this paper, the effect of modified clay on the
mechanical efficiency of epoxy resin is examined. Studies by X ray
diffraction and microscopic transient electron method show that
modified clay distribution in polymer area is intercalated kind.
Examination the results of mechanical tests shows that existence of
modified clay in epoxy area increases pressure yield strength, tension
module and nano composite fracture toughness in relate of pure
epoxy. By microscopic examinations it is recognized too that the
action of toughness growth of this kind of nano composite is due to
crack deflection, formation of new surfaces and fracture of clay piles.
Abstract: When designing satellites, one of the major issues aside for designing its primary subsystems is to devise its thermal. The thermal management of satellites requires solving different sets of issues with regards to modelling. If the satellite is well conditioned all other parts of the satellite will have higher temperature no matter what. The main issue of thermal modelling for satellite design is really making sure that all the other points of the satellite will be within the temperature limits they are designed. The insertion of power electronics in aerospace technologies is becoming widespread and the modern electronic systems used in space must be reliable and efficient with thermal management unaffected by outer space constraints. Many advanced thermal management techniques have been developed in recent years that have application in high power electronic systems. This paper presents a Three-Dimensional Modal Transmission Line Matrix (3D-TLM) implementation of transient heat flow in space power electronics. In such kind of components heat dissipation and good thermal management are essential. Simulation provides the cheapest tool to investigate all aspects of power handling. The 3DTLM has been successful in modeling heat diffusion problems and has proven to be efficient in terms of stability and complex geometry. The results show a three-dimensional visualisation of self-heating phenomena in the device affected by outer space constraints, and will presents possible approaches for increasing the heat dissipation capability of the power modules.