Abstract: Threedimensional numerical simulations are conducted on a full scale CANDU Moderator and Transient variations of the temperature and velocity distributions inside the tank are determined. The results show that the flow and temperature distributions inside the moderator tank are three dimensional and no symmetry plane can be identified.Competition between the upward moving buoyancy driven flows and the downward moving momentum driven flows, results in the formation of circulation zones. The moderator tank operates in the buoyancy driven mode and any small disturbances in the flow or temperature makes the system unstable and asymmetric. Different types of temperature fluctuations are noted inside the tank: (i) large amplitude are at the boundaries between the hot and cold (ii) low amplitude are in the core of the tank (iii) high frequency fluctuations are in the regions with high velocities and (iv) low frequency fluctuations are in the regions with lower velocities.
Abstract: A DC-to-DC converter for applications involving a
source with widely varying voltage conditions with loads requiring
constant voltage from full load down to no load is presented.
The switching regulator considered is a Buck converter with Pulse
Skipping Modulation control whereby pulses applied to the switch
are blocked or released on output voltage crossing a predetermined
value. Results of the study on the performance of regulator circuit
are presented. The regulator regulates over a wide input voltage range
with slightly higher ripple content and good transient response. Input
current spectrum indicates a good EMI performance with crowding
of components at low frequency range.
Abstract: In this article the influence of higher frequency effects
in addition to a special damper design on the electrical behavior of a
synchronous generator main exciter machine is investigated. On the
one hand these machines are often highly stressed by harmonics from
the bridge rectifier thus facing additional eddy current losses. On the
other hand the switching may cause the excitation of dangerous
voltage peaks in resonant circuits formed by the diodes of the
rectifier and the commutation reactance of the machine. Therefore
modern rotating exciters are treated like synchronous generators
usually modeled with a second order equivalent circuit. Hence the
well known Standstill Frequency Response Test (SSFR) method is
applied to a test machine in order to determine parameters for the
simulation. With these results it is clearly shown that higher
frequencies have a strong impact on the conventional equivalent
circuit model. Because of increasing field displacement effects in the
stranded armature winding the sub-transient reactance is even smaller
than the armature leakage at high frequencies. As a matter of fact this
prevents the algorithm to find an equivalent scheme. This issue is
finally solved using Laplace transfer functions fully describing the
transient behavior at the model ports.
Abstract: This paper discusses aspects of re-design of loadshedding
schemes with respect to actual developments in the Kosovo
power system. Load-shedding is a type of emergency control that is
designed to ensure system stability by reducing power system load to
match the power generation supply. This paper presents a new
adaptive load-shedding scheme that provides emergency protection
against excess frequency decline, in cases when the Kosovo power
system might be disconnected from the regional transmission
network. The proposed load-shedding scheme uses the local
frequency rate information to adapt the load-shedding pattern to suit
the size and location of the occurring disturbance. The proposed
scheme is tested in a software simulation on a large scale PSS/E
model which represents nine power system areas of Southeast Europe
including the Kosovo power system.
Abstract: Solar energy is not only sustainable but also a clean
alternative to be used as source of high temperature heat for many
processes and power generation. However, the major drawback of
solar energy is its transient nature. Especially in solar
thermochemical processing, it is crucial to maintain constant or semiconstant
temperatures inside the solar reactor. In our laboratory, we
have developed a mechanism allowing us to achieve semi-constant
temperature inside the solar reactor. In this paper, we introduce the
concept along with some updated designs and provide the optical
analysis of the concept under various incoming flux.
Abstract: The seismic response of steel shear wall system considering nonlinearity effects using finite element method is investigated in this paper. The non-linear finite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of finite element code. A numerical model based on the finite element method for the seismic analysis of shear wall is presented with developing of finite element code in this research. To develop the finite element code, the standard Galerkin weighted residual formulation is used. Two-dimensional plane stress model and total Lagrangian formulation was carried out to present the shear wall response and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The presented model in this paper can be developed for analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: This paper presents an equivalent circuit model based on piecewise linear parallel branches (PLPB) to study solar cell modules which are partially shaded. The PLPB model can easily be used in circuit simulation software such as the ElectroMagnetic Transients Program (EMTP). This PLPB model allows the user to simulate several different configurations of solar cells, the influence of partial shadowing on a single or multiple cells, the influence of the number of solar cells protected by a bypass diode and the effect of the cell connection configuration on partial shadowing.
Abstract: This study describes a micro device integrated with
multi-chamber for polymerase chain reaction (PCR) with different
annealing temperatures. The device consists of the reaction
polydimethylsiloxane (PDMS) chip, a cover glass chip, and is
equipped with cartridge heaters, fans, and thermocouples for
temperature control. In this prototype, commercial software is utilized
to determine the geometric and operational parameters those are
responsible for creating the denaturation, annealing, and extension
temperatures within the chip. Two cartridge heaters are placed at two
sides of the chip and maintained at two different temperatures to
achieve a thermal gradient on the chip during the annealing step. The
temperatures on the chip surface are measured via an infrared imager.
Some thermocouples inserted into the reaction chambers are used to
obtain the transient temperature profiles of the reaction chambers
during several thermal cycles. The experimental temperatures
compared to the simulated results show a similar trend. This work
should be interesting to persons involved in the high-temperature
based reactions and genomics or cell analysis.
Abstract: A reduced order modeling approach for natural
gas transient flow in pipelines is presented. The Euler
equations are considered as the governing equations and
solved numerically using the implicit Steger-Warming flux
vector splitting method. Next, the linearized form of the
equations is derived and the corresponding eigensystem is
obtained. Then, a few dominant flow eigenmodes are used to
construct an efficient reduced-order model. A well-known test
case is presented to demonstrate the accuracy and the
computational efficiency of the proposed method. The results
obtained are in good agreement with those of the direct
numerical method and field data. Moreover, it is shown that
the present reduced-order model is more efficient than the
conventional numerical techniques for transient flow analysis
of natural gas in pipelines.
Abstract: The stability test problem for homogeneous large-scale perturbed bilinear time-delay systems subjected to constrained inputs is considered in this paper. Both nonlinear uncertainties and interval systems are discussed. By utilizing the Lyapunove equation approach associated with linear algebraic techniques, several delay-independent criteria are presented to guarantee the robust stability of the overall systems. The main feature of the presented results is that although the Lyapunov stability theorem is used, they do not involve any Lyapunov equation which may be unsolvable. Furthermore, it is seen the proposed schemes can be applied to solve the stability analysis problem of large-scale time-delay systems.
Abstract: Unsteady boundary layer flow of an incompressible
micropolar fluid over a stretching sheet when the sheet is stretched in
its own plane is studied in this paper. The stretching velocity is
assumed to vary linearly with the distance along the sheet. Two equal
and opposite forces are impulsively applied along the x-axis so that the
sheet is stretched, keeping the origin fixed in a micropolar fluid. The
transformed unsteady boundary layer equations are solved
numerically using the Keller-box method for the whole transient from
the initial state to final steady-state flow. Numerical results are
obtained for the velocity and microrotation distributions as well as the
skin friction coefficient for various values of the material parameter K.
It is found that there is a smooth transition from the small-time
solution to the large-time solution.
Abstract: This paper presents a procedure for modeling and tuning the parameters of Thyristor Controlled Series Compensation (TCSC) controller in a multi-machine power system to improve transient stability. First a simple transfer function model of TCSC controller for stability improvement is developed and the parameters of the proposed controller are optimally tuned. Genetic algorithm (GA) is employed for the optimization of the parameter-constrained nonlinear optimization problem implemented in a simulation environment. By minimizing an objective function in which the oscillatory rotor angle deviations of the generators are involved, transient stability performance of the system is improved. The proposed TCSC controller is tested on a multi-machine system and the simulation results are presented. The nonlinear simulation results validate the effectiveness of proposed approach for transient stability improvement in a multimachine power system installed with a TCSC. The simulation results also show that the proposed TCSC controller is also effective in damping low frequency oscillations.
Abstract: This study examines the design and construction of AC Electronics load surge protection in order to carry electric surge load arisen from faults in low voltage electricity system (single phase/220V) by using the principle of electronics load clamping voltage during induction period so that electric voltage could go through to safe load and continue to work. The qualification of the designed device could prevent both transient over voltage and voltage swell. Both will work in cooperation, resulting in the ability to improve and modify the quality of electrical power in Thailand electricity distribution system more effective than the past and help increase the lifetime of electric appliances, electric devices, and electricity protection equipments.
Abstract: This paper presents and discusses the numerical simulations of transient laminar natural convection cooling of high Prandtl number fluids in cubical cavities, in which the six walls of the cavity are subjected to a step change in temperature. The effect of the fluid Prandtl number on the heat transfer coefficient is studied for three different fluids (Golden Syrup, Glycerin and Glycerin-water solution 50%). The simulations are performed at two different Rayleigh numbers (5·106 and 5·107) and six different Prandtl numbers (3 · 105 ≥Pr≥ 50). Heat conduction through the cavity glass walls is also considered. The propsed correlations of the averaged heat transfer coefficient (N u) showed that it is dependant on the initial Ra and almost independent on P r. The instantaneous flow patterns, temperature contours and time evolution of volume averaged temperature and heat transfer coefficient are presented and analyzed.
Abstract: In this paper, based on steady-state models of Flexible
AC Transmission System (FACTS) devices, the sizing of static
synchronous series compensator (SSSC) controllers in transmission
network is formed as an optimization problem. The objective of this
problem is to reduce the transmission losses in the network. The
optimization problem is solved using particle swarm optimization
(PSO) technique. The Newton-Raphson load flow algorithm is
modified to consider the insertion of the SSSC devices in the
network. A numerical example, illustrating the effectiveness of the
proposed algorithm, is introduced. In addition, a novel model of a 3-
phase voltage source converter (VSC) that is suitable for series
connected FACTS a controller is introduced. The model is verified
by simulation using Power System Blockset (PSB) and Simulink
software.
Abstract: This paper presents a physics-based model for the
high-voltage fast recovery diodes. The model provides a good
trade-off between reverse recovery time and forward voltage drop
realized through a combination of lifetime control and emitter
efficiency reduction techniques. The minority carrier lifetime can be
extracted from the reverse recovery transient response and forward
characteristics. This paper also shows that decreasing the amount of
the excess carriers stored in the drift region will result in softer
characteristics which can be achieved using a lower doping level. The
developed model is verified by experiment and the measurement data
agrees well with the model.
Abstract: Power System Security is a major concern in real time
operation. Conventional method of security evaluation consists of
performing continuous load flow and transient stability studies by
simulation program. This is highly time consuming and infeasible
for on-line application. Pattern Recognition (PR) is a promising
tool for on-line security evaluation. This paper proposes a Support
Vector Machine (SVM) based binary classification for static and
transient security evaluation. The proposed SVM based PR approach
is implemented on New England 39 Bus and IEEE 57 Bus systems.
The simulation results of SVM classifier is compared with the other
classifier algorithms like Method of Least Squares (MLS), Multi-
Layer Perceptron (MLP) and Linear Discriminant Analysis (LDA)
classifiers.
Abstract: Gas turbine systems with wet compression have a
potential for future power generation, since they can offer a high
efficiency and a high specific power with a relatively low cost. In this
study influence of ambient condition on the performance of the wet
compression process is investigated with a non-equilibrium analytical
modeling based on droplet evaporation. Transient behaviors of droplet
diameter and temperature of mixed air are investigated for various
ambient temperatures. Special attention is paid for the effects of
ambient temperature, pressure ratio, and water injection ratios on the
important wet compression variables including compressor outlet
temperature and compression work. Parametric studies show that
downing of the ambient temperature leads to lower compressor outlet
temperature and consequently lower consumption of compression
work even in wet compression processes.
Abstract: An alternative approach to the use of Discrete Fourier
Transform (DFT) for Magnetic Resonance Imaging (MRI) reconstruction
is the use of parametric modeling technique. This method
is suitable for problems in which the image can be modeled by
explicit known source functions with a few adjustable parameters.
Despite the success reported in the use of modeling technique as an
alternative MRI reconstruction technique, two important problems
constitutes challenges to the applicability of this method, these are
estimation of Model order and model coefficient determination. In
this paper, five of the suggested method of evaluating the model
order have been evaluated, these are: The Final Prediction Error
(FPE), Akaike Information Criterion (AIC), Residual Variance (RV),
Minimum Description Length (MDL) and Hannan and Quinn (HNQ)
criterion. These criteria were evaluated on MRI data sets based on the
method of Transient Error Reconstruction Algorithm (TERA). The
result for each criterion is compared to result obtained by the use of a
fixed order technique and three measures of similarity were evaluated.
Result obtained shows that the use of MDL gives the highest measure
of similarity to that use by a fixed order technique.
Abstract: Network on a chip (NoC) has been proposed as a viable solution to counter the inefficiency of buses in the current VLSI on-chip interconnects. However, as the silicon chip accommodates more transistors, the probability of transient faults is increasing, making fault tolerance a key concern in scaling chips. In packet based communication on a chip, transient failures can corrupt the data packet and hence, undermine the accuracy of data communication. In this paper, we present a comparative analysis of transient fault tolerant techniques including end-to-end, node-by-node, and stochastic communication based on flooding principle.