Abstract: The low power wireless sensor devices which usually
uses the low power wireless private area network (IEEE 802.15.4)
standard are being widely deployed for various purposes and in
different scenarios. IPv6 low power wireless private area network
(6LoWPAN) was adopted as part of the IETF standard for the
wireless sensor devices so that it will become an open standard
compares to other dominated proprietary standards available in the
market. 6LoWPAN also allows the integration and communication of
sensor nodes with the Internet more viable. This paper presents a
comparative study on different available IPv6 platforms for wireless
sensor networks including open and close sources. It also discusses
about the platforms used by these stacks. Finally it evaluates and
provides appropriate suggestions which can be use for selection of
required IPv6 stack for low power devices.
Abstract: This paper presents a novel three-phase utility
frequency to high frequency soft switching power conversion circuit
with dual mode pulse width modulation and pulse density modulation
for high power induction heating applications as melting of steel and
non ferrous metals, annealing of metals, surface hardening of steel
and cast iron work pieces and hot water producers, steamers and
super heated steamers. This high frequency power conversion circuit
can operate from three-phase systems to produce high current for
high power induction heating applications under the principles of
ZVS and it can regulate its ac output power from the rated value to a
low power level. A dual mode modulation control scheme based on
high frequency PWM in synchronization with the utility frequency
positive and negative half cycles for the proposed high frequency
conversion circuit and utility frequency pulse density modulation is
produced to extend its soft switching operating range for wide ac
output power regulation. A dual packs heat exchanger assembly is
designed to be used in consumer and industrial fluid pipeline systems
and it is proved to be suitable for the hot water, steam and super
heated steam producers. Experiment and simulation results are given
in this paper to verify the operation principles of the proposed ac
conversion circuit and to evaluate its power regulation and
conversion efficiency. Also, the paper presents a mutual coupling
model of the induction heating load instead of equivalent transformer
circuit model.
Abstract: Aggressive scaling of MOS devices requires use of ultra-thin gate oxides to maintain a reasonable short channel effect and to take the advantage of higher density, high speed, lower cost etc. Such thin oxides give rise to high electric fields, resulting in considerable gate tunneling current through gate oxide in nano regime. Consequently, accurate analysis of gate tunneling current is very important especially in context of low power application. In this paper, a simple and efficient analytical model has been developed for channel and source/drain overlap region gate tunneling current through ultra thin gate oxide n-channel MOSFET with inevitable deep submicron effect (DSME).The results obtained have been verified with simulated and reported experimental results for the purpose of validation. It is shown that the calculated tunnel current is well fitted to the measured one over the entire oxide thickness range. The proposed model is suitable enough to be used in circuit simulator due to its simplicity. It is observed that neglecting deep sub-micron effect may lead to large error in the calculated gate tunneling current. It is found that temperature has almost negligible effect on gate tunneling current. It is also reported that gate tunneling current reduces with the increase of gate oxide thickness. The impact of source/drain overlap length is also assessed on gate tunneling current.
Abstract: Harmonic pollution and low power factor in power
systems caused by power converters have been of great concern. To
overcome these problems several converter topologies using
advanced semiconductor devices and control schemes have been
proposed. This investigation is to identify a low cost, small size,
efficient and reliable ac to dc converter to meet the input performance
index of UPS. The performance of single phase and three phase ac to
dc converter along with various control techniques are studied and
compared. The half bridge converter topology with linear current
control is identified as most suitable. It is simple, energy efficient
because of single switch power loss and transformer-less operation of
UPS. The results are validated practically using a prototype built
using IGBT and analog controller. The performance for both single
and three-phase system is verified. Digital implementation of closed
loop control achieves higher reliability. Its cost largely depends on
chosen bit precision. The minimal bit precision for optimum
converter performance is identified as 16-bit with fixed-point
operation. From the investigation and practical implementation it is
concluded that half bridge ac – dc converter along with digital linear
controller meets the performance index of UPS for single and three
phase systems.
Abstract: In this paper, a design methodology to implement low-power and high-speed 2nd order recursive digital Infinite Impulse Response (IIR) filter has been proposed. Since IIR filters suffer from a large number of constant multiplications, the proposed method replaces the constant multiplications by using addition/subtraction and shift operations. The proposed new 6T adder cell is used as the Carry-Save Adder (CSA) to implement addition/subtraction operations in the design of recursive section IIR filter to reduce the propagation delay. Furthermore, high-level algorithms designed for the optimization of the number of CSA blocks are used to reduce the complexity of the IIR filter. The DSCH3 tool is used to generate the schematic of the proposed 6T CSA based shift-adds architecture design and it is analyzed by using Microwind CAD tool to synthesize low-complexity and high-speed IIR filters. The proposed design outperforms in terms of power, propagation delay, area and throughput when compared with MUX-12T, MCIT-7T based CSA adder filter design. It is observed from the experimental results that the proposed 6T based design method can find better IIR filter designs in terms of power and delay than those obtained by using efficient general multipliers.
Abstract: It is believed that continuously variable transmission (CVT) will dominate the automotive transmissions in the future. The most popular design is Van Doorne-s CVT with single metal pushing V-belt. However, it is only applicable to low power passenger cars because its major limitation is low torque capacity. Therefore, this research studies a novel dual-belt CVT system to overcome the limitation of traditional single-belt CVT, such that it can be applicable to the heavy-duty vehicles. This paper presents the mathematical model of the design and its experimental verification. Experimental and simulated results show that the model developed is valid and the proposed dual-belt CVT can really overcome the traditional limitation of single-belt Van Doorne-s CVT.
Abstract: Full search block matching algorithm is widely used for hardware implementation of motion estimators in video compression algorithms. In this paper we are proposing a new architecture, which consists of a 2D parallel processing unit and a 1D unit both working in parallel. The proposed architecture reduces both data access power and computational power which are the main causes of power consumption in integer motion estimation. It also completes the operations with nearly the same number of clock cycles as compared to a 2D systolic array architecture. In this work sum of absolute difference (SAD)-the most repeated operation in block matching, is calculated in two steps. The first step is to calculate the SAD for alternate rows by a 2D parallel unit. If the SAD calculated by the parallel unit is less than the stored minimum SAD, the SAD of the remaining rows is calculated by the 1D unit. Early termination, which stops avoidable computations has been achieved with the help of alternate rows method proposed in this paper and by finding a low initial SAD value based on motion vector prediction. Data reuse has been applied to the reference blocks in the same search area which significantly reduced the memory access.
Abstract: Wireless sensor networks have been used in wide
areas of application and become an attractive area for researchers in
recent years. Because of the limited energy storage capability of
sensor nodes, Energy consumption is one of the most challenging
aspects of these networks and different strategies and protocols deals
with this area. This paper presents general methods for designing low
power wireless sensor network. Different sources of energy
consumptions in these networks are discussed here and techniques for
alleviating the consumption of energy are presented.
Abstract: Low power consumption is a major constraint for battery-powered system like computer notebook or PDA. In the past, specialists usually designed both specific optimized equipments and codes to relief this concern. Doing like this could work for quite a long time, however, in this era, there is another significant restraint, the time to market. To be able to serve along the power constraint while can launch products in shorter production period, objectoriented programming (OOP) has stepped in to this field. Though everyone knows that OOP has quite much more overhead than assembly and procedural languages, development trend still heads to this new world, which contradicts with the target of low power consumption. Most of the prior power related software researches reported that OOP consumed much resource, however, as industry had to accept it due to business reasons, up to now, no papers yet had mentioned about how to choose the best OOP practice in this power limited boundary. This article is the pioneer that tries to specify and propose the optimized strategy in writing OOP software under energy concerned environment, based on quantitative real results. The language chosen for studying is C# based on .NET Framework 2.0 which is one of the trendy OOP development environments. The recommendation gotten from this research would be a good roadmap that can help developers in coding that well balances between time to market and time of battery.
Abstract: Recently, much research has been conducted for
security for wireless sensor networks and ubiquitous computing.
Security issues such as authentication and data integrity are major
requirements to construct sensor network systems. Advanced
Encryption Standard (AES) is considered as one of candidate
algorithms for data encryption in wireless sensor networks. In this
paper, we will present the hardware architecture to implement low
power AES crypto module. Our low power AES crypto module has
optimized architecture of data encryption unit and key schedule unit
which could be applicable to wireless sensor networks. We also details
low power design methods used to design our low power AES crypto
module.
Abstract: The use of Quantum dots is a promising emerging
Technology for implementing digital system at the nano level. It is
effecient for attractive features such as faster speed , smaller size and
low power consumption than transistor technology. In this paper,
various Combinational and sequential logical structures - HALF
ADDER, SR Latch and Flip-Flop, D Flip-Flop preceding NAND,
NOR, XOR,XNOR are discussed based on QCA design, with
comparatively less number of cells and area. By applying these
layouts, the hardware requirements for a QCA design can be reduced.
These structures are designed and simulated using QCA Designer
Tool. By taking full advantage of the unique features of this
technology, we are able to create complete circuits on a single layer
of QCA. Such Devices are expected to function with ultra low
power Consumption and very high speeds.
Abstract: Design Patterns have gained more and more
acceptances since their emerging in software development world last
decade and become another de facto standard of essential knowledge
for Object-Oriented Programming developers nowadays.
Their target usage, from the beginning, was for regular computers,
so, minimizing power consumption had never been a concern.
However, in this decade, demands of more complicated software for
running on mobile devices has grown rapidly as the much higher
performance portable gadgets have been supplied to the market
continuously. To get along with time to market that is business
reason, the section of software development for power conscious,
battery, devices has shifted itself from using specific low-level
languages to higher level ones. Currently, complicated software
running on mobile devices are often developed by high level
languages those support OOP concepts. These cause the trend of
embracing Design Patterns to mobile world.
However, using Design Patterns directly in software development
for power conscious systems is not recommended because they were
not originally designed for such environment. This paper
demonstrates the adapted Design Pattern for power limitation system.
Because there are numerous original design patterns, it is not possible
to mention the whole at once. So, this paper focuses only in creating
Energy Conscious version of existing regular "Builder Pattern" to be
appropriated for developing low power consumption software.
Abstract: In this paper a novel high output impedance, low input impedance, wide bandwidth, very simple current mirror with input and output voltage requirements less than that of a simple current mirror is presented. These features are achieved with very simple structure avoiding extra large node impedances to ensure high bandwidth operation. The circuit's principle of operation is discussed and compared to simple and low voltage cascode (LVC) current mirrors. Such outstanding features of this current mirror as high output impedance ~384K, low input impedance~6.4, wide bandwidth~178MHz, low input voltage ~ 362mV, low output voltage ~ 38mV and low current transfer error ~4% (all at 50μA) makes it an outstanding choice for high performance applications. Simulation results in BSIM 0.35μm CMOS technology with HSPICE are given in comparison with simple, and LVC current mirrors to verify and validate the performance of the proposed current mirror.
Abstract: Three similar negative differential resistance (NDR)
profiles with both high peak to valley current density ratio (PVCDR)
value and high peak current density (PCD) value in unity resonant
tunneling electronic circuit (RTEC) element is developed in this paper.
The PCD values and valley current density (VCD) values of the three
NDR curves are all about 3.5 A and 0.8 A, respectively. All PV values
of NDR curves are 0.40 V, 0.82 V, and 1.35 V, respectively. The VV
values are 0.61 V, 1.07 V, and 1.69 V, respectively. All PVCDR
values reach about 4.4 in three NDR curves. The PCD value of 3.5 A
in triple PVCDR RTEC element is better than other resonant
tunneling devices (RTD) elements. The high PVCDR value is
concluded the lower VCD value about 0.8 A. The low VCD value is
achieved by suitable selection of resistors in triple PVCDR RTEC
element. The low PV value less than 1.35 V possesses low power
dispersion in triple PVCDR RTEC element. The designed multiple
value logical level (MVLL) system using triple PVCDR RTEC
element provides equidistant logical level. The logical levels of
MVLL system are about 0.2 V, 0.8 V, 1.5 V, and 2.2 V from low
voltage to high voltage and then 2.2 V, 1.3 V, 0.8 V, and 0.2 V from
high voltage back to low voltage in half cycle of sinusoid wave. The
output level of four levels MVLL system is represented in 0.3 V, 1.1 V,
1.7 V, and 2.6 V, which satisfies the NMP condition of traditional
two-bit system. The remarkable logical characteristic of improved
MVLL system with paralleled capacitor are with four significant
stable logical levels about 220 mV, 223 mV, 228 mV, and 230 mV.
The stability and articulation of logical levels of improved MVLL
system are outstanding. The average holding time of improved MVLL
system is approximately 0.14 μs. The holding time of improved
MVLL system is fourfold than of basic MVLL system. The function of
additional capacitor in the improved MVLL system is successfully
discovered.
Abstract: One of the most growing areas in the embedded community is multimedia devices. Multimedia devices incorporate a number of complicated functions for their operation, like motion estimation. A multitude of different implementations have been proposed to reduce motion estimation complexity, such as spiral search. We have studied the implementations of spiral search and identified areas of improvement. We propose a modified spiral search algorithm, with lower computational complexity compared to the original spiral search. We have implemented our algorithm on an embedded ARM based architecture, with custom memory hierarchy. The resulting system yields energy consumption reduction up to 64% and performance increase up to 77%, with a small penalty of 2.3 dB, in average, of video quality compared with the original spiral search algorithm.
Abstract: Structural representation and technology mapping of
a Boolean function is an important problem in the design of nonregenerative
digital logic circuits (also called combinational logic
circuits). Library aware function manipulation offers a solution to
this problem. Compact multi-level representation of binary networks,
based on simple circuit structures, such as AND-Inverter Graphs
(AIG) [1] [5], NAND Graphs, OR-Inverter Graphs (OIG), AND-OR
Graphs (AOG), AND-OR-Inverter Graphs (AOIG), AND-XORInverter
Graphs, Reduced Boolean Circuits [8] does exist in
literature. In this work, we discuss a novel and efficient graph
realization for combinational logic circuits, represented using a
NAND-NOR-Inverter Graph (NNIG), which is composed of only
two-input NAND (NAND2), NOR (NOR2) and inverter (INV) cells.
The networks are constructed on the basis of irredundant disjunctive
and conjunctive normal forms, after factoring, comprising terms with
minimum support. Construction of a NNIG for a non-regenerative
function in normal form would be straightforward, whereas for the
complementary phase, it would be developed by considering a virtual
instance of the function. However, the choice of best NNIG for a
given function would be based upon literal count, cell count and
DAG node count of the implementation at the technology
independent stage. In case of a tie, the final decision would be made
after extracting the physical design parameters.
We have considered AIG representation for reduced disjunctive
normal form and the best of OIG/AOG/AOIG for the minimized
conjunctive normal forms. This is necessitated due to the nature of
certain functions, such as Achilles- heel functions. NNIGs are found
to exhibit 3.97% lesser node count compared to AIGs and
OIG/AOG/AOIGs; consume 23.74% and 10.79% lesser library cells
than AIGs and OIG/AOG/AOIGs for the various samples considered.
We compare the power efficiency and delay improvement achieved
by optimal NNIGs over minimal AIGs and OIG/AOG/AOIGs for
various case studies. In comparison with functionally equivalent,
irredundant and compact AIGs, NNIGs report mean savings in power
and delay of 43.71% and 25.85% respectively, after technology
mapping with a 0.35 micron TSMC CMOS process. For a
comparison with OIG/AOG/AOIGs, NNIGs demonstrate average
savings in power and delay by 47.51% and 24.83%. With respect to
device count needed for implementation with static CMOS logic
style, NNIGs utilize 37.85% and 33.95% lesser transistors than their
AIG and OIG/AOG/AOIG counterparts.
Abstract: This paper presents two prototypes of low power low voltage current mode 9 bit pipelined a/d converters. The first and the second converters are configured of 1.5 bit and 2.5 bit stages, respectively. The a/d converter structures are composed of current mode building blocks and final comparator block which converts the analog current signal into digital voltage signal. All building blocks have been designed in CMOS AMS 0.35μm technology, then simulated to verify proposed concept. The performances of both converters are compared to performances of known current mode and voltage mode switched capacitance converter structures. Low power consumption and small chip area are advantages of the proposed converters.
Abstract: A digital system is proposed for low power 100-
channel neural recording system in this paper, which consists of 100
amplifiers, 100 analog-to-digital converters (ADC), digital controller
and baseband, transceiver for data link and RF command link. The
proposed system is designed in a 0.18 μm CMOS process and 65 nm
CMOS process.
Abstract: Although White LED lighting systems powered by solar cells have presented for many years, they are not widely used in today application because of their cost and low energy conversion efficiency. The proposed system use the dc power generated by fixed solar cells module to energize White LED light sources that are operated by directly connected White LED with current limitation resistors, resulting in much more power consumption. This paper presents the use of white LED as a general lighting application powered by tracking solar cells module and using pulse to apply the electrical power to the White LED. These systems resulted in high efficiency power conversion, low power consumption, and long light of the white LED.
Abstract: In this paper an algorithm for fast wavelength calibration of Optical Spectrum Analyzers (OSAs) using low power reference gas spectra is proposed. In existing OSAs a reference spectrum with low noise for precise detection of the reference extreme values is needed. To generate this spectrum costly hardware with high optical power is necessary. With this new wavelength calibration algorithm it is possible to use a noisy reference spectrum and therefore hardware costs can be cut. With this algorithm the reference spectrum is filtered and the key information is extracted by segmenting and finding the local minima and maxima. Afterwards slope and offset of a linear correction function for best matching the measured and theoretical spectra are found by correlating the measured with the stored minima. With this algorithm a reliable wavelength referencing of an OSA can be implemented on a microcontroller with a calculation time of less than one second.